Purlin Span= 7m

Purlin Spacing= 1.56 m Ref : SP 38

Basic Wind Speed:Vb 50 m/s
Risk Coefficient K1 1.05
Bldg Ht & Terrain Categary Factor K2 1.05
Topography factor K3 1.05
Design Wind Speed:Vz=VbK1K2K3 58 m/s
Design Wind Pressure Pd=0.6Vz /1000=
2
###
External Pressure Coeff Cpe= 1
Internal Pressure Coeff Cpi= 0.5
Effective Wind Pressure=(Cpe+Cpi)Pd= ###
Roof Angle= 18 degree
Weight of Alluminium Sheet= .20 kN/m²
Whether sag rods provided?y/n n

Calculations:
Weight of Sheet per m= 0.312 kN/m
Try ISMC200
Selfweight= 0.221 kN/m
Live Load on projected area= 0.59 kN/m2
Total Dead Load wd= 0.533 kN/m
Total Live Load wl= 0.92 kN/m
DL+LL=wdl= 1.453 kN/m
Wind load uplift force= 4.704 kN/m
Net uplift force=wwd= 4.197 kN/m
Considering unsymmtetrical bending of the Purlin member,
Mxx=wdlx(span about x)2xcosa/10= 5.84 kNm
Myy=wdlx(span about y)2xsina/10= 1.898 kNm
Checking the section ISMC200
Zxx= 182 cm 3

Zyy= 26.3 cm3

sbc cal= 104.3 N/mm2 < 165 So OK
Under uplift condition,
Mxx=wwdx(span about x)2/10= 17.73 kNm
Myy=wdx(span about y)2xsina/10= 0.696 kNm
sbc cal= 123.9 N/mm2 < 1.33x158 So OK

Deflection Check (Ref. Draft Copy of IS 800:2004)

Actual deflection = 5.59 mm < Allowable deflection = 43 mm So OK
 w a Cx Cy h b tf tw Ix
L50X50X6 4.5 5.68 1.45 1.45 50 50 6 6 12.9
L65X65X6 5.8 7.44 1.81 1.81 65 65 6 6 29.1
L75X75X6 6.8 8.66 2.06 2.06 75 75 6 6 45.7
L90X90X6 8.2 10.47 2.42 2.42 90 90 6 6 80.1
L90X90X8 10.8 13.79 2.51 2.51 90 90 8 8 104.2
L100X100X6 9.2 11.67 2.67 2.67 100 100 6 6 111.3
L100X100X8 12.1 15.39 2.76 2.76 100 100 8 8 145.1
L100X100X10 14.9 19.03 2.84 2.84 100 100 10 10 177
ISMC75 6.8 8.67 3.75 1.31 75 40 7.3 4.4 76
ISMC100 9.2 11.7 5 1.53 100 50 7.5 4.7 186.7
ISMC125 12.7 16.19 6.25 1.94 125 65 8.1 5 416.4
ISMC150 16.4 20.88 7.5 2.22 150 75 9 5.4 779.4
ISMC200 22.1 28.21 10 2.17 200 75 11.4 6.1 1819.3
ISMC250 30.4 38.67 12.5 2.3 250 80 14.1 7.1 3816.8
ISMC300 35.8 45.64 15 2.36 300 90 13.6 7.6 6362.6
ISMC350 42.1 53.65 17.5 2.44 350 100 13.5 8.1 10008
ISMC400 49.4 62.93 20 2.42 400 100 15.3 8.6 15082.8
ISMB150 14.9 19 7.5 4 150 80 7.6 4.8 726.4
ISMB200 25.4 32.33 10 5 200 100 10.8 5.7 2235.4
ISMB250 37.3 47.55 12.5 6.25 250 125 12.5 6.9 5131.6
ISMB300 44.2 56.26 15 7 300 140 12.4 7.5 8603.6
ISMB350 52.4 66.71 17.5 7 350 140 14.2 8.1 13630.3
ISMB400 61.6 78.46 20 7 400 140 16 8.9 20458.4
ISMB450 72.4 92.27 22.5 7.5 450 150 17.4 9.4 30390.8
ISMB500 86.9 110.74 25 9 500 180 17.2 10.2 45218.3
ISMB600 122.6 156.21 30 10.5 600 210 20.8 12 91813

RHS96483.2 6.7 8.55 4.8 2.4 96 48 3.2 3.2 98.61

RHS96484.0 8.22 10.47 4.8 2.4 96 48 4 4 117.55
RHS96484.8 9.66 12.31 4.8 2.4 96 48 4.8 4.8 134.35
RHS122613.6 9.67 12.32 6.1 3.05 122 61 3.6 3.6 232.61
RHS122614.5 11.88 15.14 6.1 3.05 122 61 4.5 4.5 278.94
RHS122615.4 14.01 17.85 6.1 3.05 122 61 5.4 5.4 320.83
RHS145824.8 15.92 20.28 7.05 4.1 145 82 4.8 4.8 555.16
RHS145825.4 17.74 22.6 7.05 4.1 145 82 5.4 5.4 610.85
RHS172924.8 18.71 23.83 8.6 4.6 172 92 4.8 4.8 917.13
RHS172925.4 20.88 26.59 8.6 4.6 172 92 5.4 5.4 1012.47

PROPERTIES OF COMBINED SECTION:

SECTION: DOUBLE L90X90X6 SPACING:
DOUBLE ANGLES: AREA: 20.94
 IZZ 160.2 ZZZt 66.19835
Y IYY 326.723256 ZYY 34.75779

Z Z
rzz 2.7659410333
rYY 3.9500417465
Y
Y SECTION: DOUBLE ISMC150 SPACING:
Y
DOUBLE CHANNELS(BACK TO BACK): AREA: 41.76
IZZ 1558.8 ZZZ 207.84
Y IYY ZYY
469.792704 60.22983
Z Z
rzz 6.1096306113
Y
rYY
SY 3.3540759215
Y

SECTION: DOUBLE ISMC200 SPACING:

DOUBLE CHANNELS(BACK TO BACK): AREA: 56.42
IZZ 3638.6 ZZZ 363.86
Y IYY ZYY
6301.316138 504.1053
Z Z
rzz 8.0306484879 Leff zz 11.25
Y
rYY 10.568153033 Leff yy 15
SY
Y

SECTION: ISMB600 ISMC400

BEAM WITH CHANNEL ON TOP: AREA: 219.14 C ZZt 22.69294
IZZ 128600.87537 ZZZt 5666.999
Y IYY ZYYtop flange only
Czzt 17733.8

Z Z
Czzb
rzz 24.224852072
rYY 8.9958058636
Y
Y
Y
 SECTION: DOUBLE L75x75x6 SPACING:
STAR ANGLES: AREA: 17.32
IZZ 196.213712 ZZZ 24.83718
Y IYY 196.213712 ZYY 24.83718

rzz 3.3658188095
rYY 3.3658188095
Z Z

Y
Y SECTION: ISMB200 B t B t
Y
BEAM WITH PLATES AT WEB PLATES: 0 0 TOP PLATE: 15 0.6
TOP & BOTTOM & WEBS: AREA: 50.33 C ZZt 10.60
Y IZZ 4145.56 ZZZt 391.0906
Czzt IYY 487.5 ZYY top flange only

Z Z

Czzb rzz 9.0756583239

rYY 3.1122454796
Y
Y
Y
DESIGN FOR AXIAL COMPRESSIOM & BENDING:
P= 0 KN
My= 0 KN m
Mz= 0.63 KN m
Leff y= 0 m
Leff z= 2.4 m

Trial Section : L65X65X6

 Iy rx ry ru rv Zx Zy Leffyy Leffzz lyy lzz sac sbcy sbcz Pac
12.9 1.51 1.51 1.9 0.96 3.6 3.6 4.1968 4.7037 277.9 311.51 11.954 111.0378 105.45 50
29.1 1.98 1.98 2.5 1.26 6.2 6.2 4.1968 4.7037 212 237.56 20.085 112.2216 106.52 50
45.7 2.3 2.3 2.91 1.46 8.4 8.4 4.1968 4.7037 182.5 204.51 26.513 113.4365 107.61 50
80.1 2.77 2.77 3.5 1.75 12.2 12.2 4.1968 4.7037 151.5 169.81 36.88 115.6477 109.54 50
104.2 2.75 2.75 3.47 1.75 16 16 4.1968 4.7037 152.6 171 36.422 125.9707 120.86 50
111.3 3.09 3.09 3.91 1.95 15.2 15.2 4.1968 4.7037 135.8 152.22 44.314 117.7137 111.39 50
145.1 3.07 3.07 3.88 1.95 20 20 4.1968 4.7037 136.7 153.22 43.845 127.1649 121.95 50
177 3.05 3.05 3.85 1.94 24.7 24.7 4.1968 4.7037 137.6 154.22 43.376 134.0511 129.66 50
12.6 2.96 1.21 2.96 1.21 20.3 4.7 4.1968 4.7037 346.8 158.91 9.6947 89.49378 127.49 50
25.9 4 1.49 4 1.49 37.3 7.5 4.1968 4.7037 281.7 117.59 14.524 87.47144 131.75 50
59.9 5.07 1.92 5.07 1.92 66.6 13.1 4.1968 4.7037 218.6 92.776 23.461 94.30674 138.23 50
102.3 6.11 2.21 6.11 2.21 103.9 19.4 4.1968 4.7037 189.9 76.984 30.309 98.78026 144.27 50
140.4 8.03 2.23 8.03 2.23 181.9 26.3 4.1968 4.7037 188.2 58.577 30.801 97.06504 152.43 50
219.3 9.94 2.38 9.94 2.38 305.3 38.4 4.1968 4.7037 176.3 47.321 34.548 100.4287 157.09 50
310.8 11.81 2.61 11.81 2.61 424.4 46.8 4.1968 4.7037 160.8 39.828 40.463 97.46915 159.46 50
430.6 13.66 2.83 13.66 2.83 571.9 57 4.1968 4.7037 148.3 34.434 46.239 97.37639 161.08 50
504.8 15.48 2.83 15.48 2.83 754.1 66.6 4.1968 4.7037 148.3 30.386 46.239 97.11314 162.17 50
52.6 6.18 1.66 6.18 1.66 96.9 13.1 4.1968 4.7037 252.8 76.112 17.856 74.79603 142.69 50
150 8.32 2.15 8.32 2.15 223.5 30 4.1968 4.7037 195.2 56.535 28.849 92.56662 153.06 50
334.5 10.39 2.65 10.39 2.65 410.5 53.5 4.1968 4.7037 158.4 45.272 41.507 102.101 157.59 50
453.9 12.37 2.84 12.37 2.84 573.6 64.8 4.1968 4.7037 147.8 38.025 46.503 99.84662 159.99 50
537.7 14.29 2.84 14.29 2.84 778.9 76.8 4.1968 4.7037 147.8 32.916 46.503 99.23929 161.53 50
622.1 16.15 2.82 16.15 2.82 1022.9 88.9 4.1968 4.7037 148.8 29.125 45.975 98.29314 162.48 50
834 18.15 3.01 18.15 3.01 1350.7 111.2 4.1968 4.7037 139.4 25.916 50.993 101.7867 163.14 50
1369.8 20.21 3.52 20.21 3.52 1808.7 152.2 4.1968 4.7037 119.2 23.274 64.258 110.0756 163.6 50
2651 24.24 4.12 24.24 4.12 3060.4 252.5 4.1968 4.7037 101.9 19.405 78.742 121.4416 164.14 50

33.28 3.4 1.97 3.4 1.97 20.54 13.27

39.32 3.35 1.94 3.35 1.94 24.49 16.38
44.55 3.3 1.9 3.3 1.9 27.99 18.56
78.83 4.34 2.53 4.34 2.53 38.13 25.84
93.78 4.29 2.49 4.29 2.49 45.73 30.75
107.03 4.24 2.45 4.24 2.45 52.6 35.09
228.5 5.23 3.36 5.23 3.36 76.51 55.73
250.59 5.2 3.33 5.2 3.33 84.26 61.12
346.91 6.2 3.82 6.2 3.82 106.64 75.41
381.74 6.17 3.79 6.17 3.79 117.73 82.99

8 mm
 ZZZb 24.347

6 mm

250 mm

lzz 140.09
lyy 141.94

sac 49.589 x y T D c1 c2 k1 k2 fbc

sbc 113 322.5 131.54 14.105 200 125 125 1 0 322.4779

C ZZb 38.167
ZZZb 3369
820.415
 8 mm

B t
BOTTOM PL: 15 0.6
C ZZb 10.6
ZZZb 391.09

32.50
Myy Mzz Ratio sbcALLO.
25 25 L50X50X6 165
25 25 L65X65X6 165
25 25 L75X75X6 165
25 25 L90X90X6 165
25 25 L90X90X8 165
25 25 L100X100X6 165
25 25 L100X100X8 165
25 25 L100X100X10 165
25 25 ISMC75 165
25 25 ISMC100 165
25 25 ISMC125 165
25 25 ISMC150 165
25 25 ISMC200 165
25 25 ISMC250 165
25 25 ISMC300 165
25 25 ISMC350 165
25 25 ISMC400 165
25 25 ISMB150 165
25 25 ISMB200 165
25 25 ISMB250 165
25 25 ISMB300 165
25 25 ISMB350 165
25 25 ISMB400 165
25 25 ISMB450 165
25 25 ISMB500 165
25 25 ISMB600 165

158
158
158
158
158
158
158
158
158
158
158
528529072.xls\SHEET 3\06/18/2021\11:46:35
528529072.xls\SHEET 3\06/18/2021\11:46:35
528529072.xls\SHEET 3\06/18/2021\11:46:35
528529072.xls\SHEET 3\06/18/2021\11:46:35
528529072.xls\SHEET 3\06/18/2021\11:46:35
Purlin Span= 9m
Purlin Spacing= 1.05 m Ref : SP 38
Basic Wind Speed:Vb 50 m/s
Risk Coefficient K1 1.05
Bldg Ht & Terrain Categary Factor K2 1.05
Topography factor K3 1.05
Design Wind Speed:Vz=VbK1K2K3 58 m/s
Design Wind Pressure Pd=0.6Vz2/1000= ###
External Pressure Coeff Cpe= 1
Internal Pressure Coeff Cpi= 0.5
Effective Wind Pressure=(Cpe+Cpi)Pd= ###
Roof Angle= 2 degree
Weight of Alluminium Sheet= .20 kN/m²
Whether sag rods provided?y/n n

Calculations:
Weight of Sheet per m= 0.21 kN/m
Try ISMC175
Selfweight= #N/A kN/m
Live Load on projected area= 0.75 kN/m2
Total Dead Load wd= #N/A kN/m
Total Live Load wl= 0.789 kN/m
DL+LL=wdl= #N/A kN/m
Wind load uplift force= 3.172 kN/m
Net uplift force=wwd= #N/A kN/m
Considering unsymmtetrical bending of the Purlin member,
Mxx=wdlx(span about x)2xcosa/10= #N/A kNm
Myy=wdlx(span about y) xsina/10=
2 #N/A kNm
Checking the section ISMC175
Zxx= ### cm3
Zyy= ### cm3
sbc cal= #N/A N/mm2 < ### ###
Under uplift condition,
Mxx=wwdx(span about x)2/10= #N/A kNm
Myy=wdx(span about y)2xsina/10= #N/A kNm
sbc cal= #N/A N/mm2 ###

Deflection Check (Ref. Draft Copy of IS 800:2004)

Actual deflection = #N/A mm ### 63 ###
Ref : SP 38

M/Z)x= #REF!
M/Z)y= #REF!