Completion Systems

HYDRAULIC PRODUCTION PACKERS

HYDROW IIA
The Weatherford Hydrow IIA is a mechanically held dual string production packer.

The Hydrow IIA is available with short or long string setting capabilities and a
variety of tubing connections. The packer has been carefully designed for
maximum flexibility when it comes to submersible pump applications. By changing
only a few parts, the Hydrow IIA can be modified from a high-pressure production
packer to a packer installation for submersible pumps.

Hydrow IIA
The Hydrow IIA has a patented sequential upper slip releasing system that is Scoop Head
designed so that each slip is released individually to reduce the pull required to
release the packer. The angles on the slips, cone, and the upper slip body results
in releasing forces which allows the penetration of the slips to release smoothly
from the casing.

Applications:
Normally run above a single string hydraulic or wireline set seal bore packer. The
short length of the Hydrow IIA makes it ideally suited for deviated wells or doglegs.
Also, since there is no tubing manipulation required to set the packer, the
wellhead can be installed and flanged up before setting the packer.

Features:
• Short, compact and economical
• No hydraulic hold down buttons
• Shear release easily adjusted
• Sequential upper slip system for easy release
• Setting cylinder below elements to eliminate all of the critical o-rings after setting
• Hydraulic set to allow flanging-up before setting packer
• Differential pressures help to improve the rubber pack-off
• Can be pressure tested on location
• Multiple bores available for control line, ESP cable, chemical injection line,
and well monitoring devices
• Three seal options for the short string; J-latch, locator, or snap latch

SETTING PROCEDURE
The Hydrow IIA is set by temporarily plugging the long string and pressuring the
tubing.

When tubing pressure is applied to the packer, the inlet port allows pressure
differential to be present in the setting chamber. This differential forces the setting
cylinder down and sets the lower slips. The setting mandrel is forced up, and sets
the upper slips and packs-off the elements. Any relative motion between the
setting cylinder and the setting mandrel is held in place by the locking nut, which
will ratchet in only one direction. With a pressure differential from above, the force
is transferred through the outer components of the packer and is supported by the
lower slips. With pressure differential from below the force transfers through the
outer components of the packer and is supported by the upper slips.

RELEASING PROCEDURE
The Hydrow IIA is released by a straight pick-up on the long string. The shear
Hydrow IIA-P Hydrow IIA-P
release value is adjustable.

© 2000 WEATHERFORD. All Rights Reserved. Houston, TX USA • Ph 713/693-4000 • 800/257-3826 • Fax 713/693-4227
 Completion Systems
HYDROW IIA SPECIFICATION GUIDE
CASING LONG STRING SHORT STRING SEAL
PACKER BASE
BORE
O.D. STANDARD MANDREL STANDARD SEALNIPPLE PRODUCT
O.D. WEIGHT I.D.
in/ m m THREAD I.D. THREAD I.D. NUMBER
in/ m m lb/ft in/ m m
CONNECTIONS in/ m m CONNECTIONS in/ m m
5-1/2 4.625 1.531 1.313 1.969
14.0 - 20.0 1.900 NU 10RD 1.660 NU 10RD 905-55
139,70 117,48 38,89 33,35 50,01
7 5.938 1.938 1.938 2.688
23.0 - 32.0 2-3/8 EU 8RD 2-3/8 EU 8RD 905-70
177,80 150,83 49,23 49,23 68,28
7 6.000 1.938 1.938 2.688
17.0 - 29.0 2-3/8 EU 8RD 2-3/8 EU 8RD 905-72
177,80 152,40 49,23 49,23 68,28
7-5/8 6.453 1.938 1.938 2.688
33.7 - 39.0 2-3/8 EU 8RD 2-3/8 EU 8RD 905-75
193,68 163,91 49,23 49,23 68,28
7-5/8 6.625 2.406 2.406 2.688
24.0 - 29.7 2-7/8 EU 8RD 2-7/8 EU 8RD 905-76
193,68 168,28 61,11 61,11 68,28
8-5/8 7.531 2.406 2.406 3.250
28.0 - 40.0 2-7/8 EU 8RD 2-7/8 EU 8RD 905-85
219,08 191,29 61,11 61,11 82,55
9-5/8 8.250 3.000 3.000 3.750
47.0 -53.0 3-1/2 EU 8RD 3-1/2 EU 8RD 905-95
244,48 209,55 76,20 76,20 95,25
9-5/8 8.500 3.000 3.000 3.750
36.0 - 47.0 3-1/2 EU 8RD 3-1/2 EU 8RD 905-96
244,48 215,90 76,20 76,20 95,25

HYDRAULIC PRODUCTION ACCESSORIES

Y-BLOCK
The Weatherford Y-Block is designed to split the tubing from one to two strings.
There are two separate strings that communicate with each other. The Y-Block
includes cable by-pass areas for ESP applications.

Y- B LOCK SPECIFICATION GUIDE

CASING TOOL SIZE AND CONNECTION BASE

PRODUCT
O.D. MAX. O.D. NUMBER
THRU STRING SHORT STRING
in/ m m in/ m m
7 5.938
2-7/8 EU 8RD 2-3/8 EU 8RD 198-70
177,80 150,83
9-5/8 8.500
2-7/8 EU 8RD 3-1/2 EU 8RD 198-95
244,58 215,90

SAFETY JOINT
The Weatherford Safety Joint allows a positive release of the tubing string in
Y-Block
completions where tool retrieval problems are anticipated. The keyed model
allows torque to be transmitted through the Safety Joint. The standard model
allows the tubing to be rotated without transmitting torque through the Safety Joint.
SAFETY JOINT SPECIFICATION GUIDE
TOOL BASE PRODUCT NUMBER
TUBING
MAX. MIN. STANDARD
in/ m m
O.D . I.D. THREAD ROTATIONAL SHEAR- OUT
in/m m in/m m CONNECTIONS
3/4 1.750 0.750
1.315 NU 10RD N/A 569-10
19,05 44,45 19,05
1-1/4 2.250 1.250
1.660 NU 10RD 568-16 569-26
31,75 57,15 31,75
1-1/2 2.688 1.610
1.900 NU 10RD N/A 569-19
38,10 68,28 40,89
2-3/8 3.063 2.000
2-3/8 EU 8RD 568-20 569-20
60,33 77,80 50,80
2-7/8 3.688 2.500
2-7/8 EU 8RD 568-25 569-25
73,03 93,68 63,50
3-1/2 4.500 3.000
Safety Joint
3-1/2 EU 8RD 568-35 569-35
88,90 114,30 76,20

© 2000 WEATHERFORD. All Rights Reserved. Houston, TX USA • Ph 713/693-4000 • 800/257-3826 • Fax 713/693-4227
 INDEX NO.: 200
UNIT NO.: 905-70A-SSS
PN: 905-70A-SSS
905-72A-SSS
PAGE: 1 OF 3

7” X 2-3/8” X 2-3/8”” HYDROW IIA-P DUAL STRING PACKER OPERATION

(SHORT STRING SET) When tubing pressure is applied to the packer, the inlet port allows a pressure differential to be present
in the setting chamber. This differential forces the setting mandrel to separate from the setting cylinder,
The Weatherford Hydrow IIA-P is a hydraulic set, mechanically held dual string production packer, shearing the setting shear screws. The setting cylinder is forced down, which shears the lower slip body
which is normally run above an electrical submersible pump. The unique design allows for the largest shear screws and sets the lower slips. The setting mandrel is forced up, which shears the upper slip
possible production string and feed through combinations. The short length of the Hydrow IIA-P body shear screws, and sets the upper slips and packs off the elements. Any relative motion between
makes it ideally suited for deviated wells or doglegs. Also, since there is no tubing manipulation the setting cylinder and the setting mandrel is held in place by the locking nut, which will ratchet in only
required to set the packer, the well head can be installed and flanged up before setting the packer. one direction. With a pressure differential from above, the force is transferred through the outer
The Hydrow IIA-P is designed with all critical o-rings below the packing elements. These o-rings can components of the packer and is supported by the lower slips. With a pressure differential from below,
be pressure tested prior to running the packer. This test can be performed in the shop or at the rig the force transfers through the outer components of the packer and is supported by the upper slips.
utilizing the o-ring Pressure Test Kit. The Hydrow IIA-P has as sequential upper slip releasing system
that is designed so that each slip is released individually to reduce the pull required to release the
packer. The angles on the slips, cone, and the resultant releasing force allow the penetration of the
DISASSEMBLY
slips to release smoothly from the casing. PATENT #4,813,486.
1.) Place top connection (3) in the vise. Remove changeovers (29 & 30).
2.) Remove coupling (1) and nipple (2) from top connection (3). Remove releasing shear screws (27)
SPECIFICATION GUIDE from shear sleeve (28) and remove shear sleeve (28) from lower slip body cap (26). Remove
torque screws (9) and shear screws (10) from lower slip body (24).
RECOMMENDED O.D. 3.) Remove lower slip body (24) assembly from mandrels (4 & 5). Remove slips (23) and slip springs
CASING
CASING RANGE OF PRODUCT (8) from lower slip body (24).
SIZE WEIGHT MIN. MAX. TOOL NUMBER 4.) Remove lower slip body cap (26) from lower slip body (24). Remove pick-up ring (25) from long
(IN.) (LBS./FT.) (IN.) (IN.) (IN.) string mandrel (4). {use snap ring pliers} Remove setting mandrel assembly (16 through 22) from
7 23.0 - 32.0 6.094 6.366 5.938 905-70A-SSS mandrels (4 & 5).
5.) Remove lower cone (22) from setting cylinder (19). Remove o-rings (12 & 21).
7 17.0 - 29.0 6.184 6.538 6.000 905-72A-SSS
6.) Remove shear screws (16) from setting cylinder (19). Rotate setting mandrel (18) to remove it
from locking nut (20) and out of setting cylinder (19). Remove lock nut (20) from setting cylinder
LONG STRING SHORT STRING (19). Remove o-ring (17) from setting cylinder (19). Remove o-rings (12) from setting mandrel
THREAD MANDREL THREAD MANDREL (18).
CONNECTION I.D. CONNECTION I.D. 7.) Remove packing elements (13 & 15) and rubber spacers (14) from mandrels (4 & 5).
BOX UP / PIN DOWN (IN.) BOX UP / PIN DOWN (IN.) 8.) Remove torque screws (9) and shear screws (10) from upper slip body (6).
2-3/8" EU 8 rd 1.938 2-3/8" EU 8 rd 1.938 9.) Remove upper cone (11) from mandrels (4 & 5). Remove o-rings (12) from upper cone (11).
10.) Remove upper slip (7) and slip springs (8) from upper slip body (6). Remove upper slip body (6)
from top connection (3).
SETTING PROCEDURES 11.) Remove long string mandrel (4) and short string mandrel (5) from top connection (3). DO NOT
WRENCH ON SEAL SURFACES OF MANDRELS. Clean and inspects all parts. Replace any
Run the packer in the well slowly (maximum of 60 ft. in 30 seconds is recommended). If both strings worn or damaged parts.
are run simultaneously, allow at least 30 minutes for the packer to equalize thermally before setting.
Temporarily plug the short string below the packer and apply a minimum of 2,500-PSI differential PACKING ELEMENT GUIDE
in the tubing at the packer and hold the pressure for at least 10 minutes. The packer should now
be fully set and can be pressure tested if desired.
TEMP. ELEMENT DURO
CLASSIFICATION
RANGE END MIDDLE END
RELEASING PROCEDURES LOW TEMPERATURE 60 - 125 80 60 80
STANDARD TOOL 125 - 225 90 70 90
The Hydrow IIA-P packer is released by a straight pick up on the long string. The shear release value
is adjustable in 4,250 lb. increments up to 29,750 lbs. MODERATE TEMP. 225 - 275 90 80 90
HIGH TEMPERATURE 275 - UP CONTACT TECH. SALES
NO. OF RELEASE SHEAR MAX. NUMBER OF LOWER SLIP
SHEAR SCREWS INSTALLED BODY SHEAR SCREWS
7 (29,700 LBS.) 4
SCREW 6 (25,500 LBS.) 3
GUIDE 5 (21,250 LBS.) 2
LESS THAN 5 RELEASE SCREWS IS NOT RECOMMENDED

© 1999 WEATHERFORD All Rights Reserved. NORTH AMERICAN NUMBERS: HUNTSVILLE, TX PH:800/331-4042 USA 409/295-0080 FAX:409/295-9132 • POWELL, WY PH:307/754-7234 800/458-9202 USA FAX:307/754-5875 REV. 00/DTD: 09-30-99
 INDEX NO.: 200
UNIT NO.: 905-70A-SSS
PN: 905-70A-SSS
905-72A-SSS
PAGE: 2 OF 3

PARTS LIST PARTS LIST

7" 7" 7" 7

ITEM ITEM
DESCRIPTION 23.0 - 32.0 17.0 - 29.0 DESCRIPTION 23.0 - 32.0 17.0 - 29.0
NO. NO.
905-70A-SSS 905-72A-SSS 905-70A-SSS 905-72A-SSS
1 COUPLING 905-70-600 905-70-600 13 PACKING ELEMENT* 905-70-512 (2) 905-70-512 (2)
2 NIPPLE 905-70-102 905-70-102 14 RUBBER SPACER 905-70-841 (2) 905-70-841 (2)
3 TOP CONNECTION 905-70-624 905-70-624 15 PACKING ELEMENT* 905-70-511 905-70-511
4 LONG STRING MANDREL 905-70-213 905-70-213 16 SHEAR SCREW*175 PSI / EA. B20-C5-005 (8) B20-C5-005 (8)
5 SHORT STRING MANDREL 907-72-226 907-72-226 17 O-RING* 050-90-252 050-90-252
6 UPPER SLIP BODY 905-70-321 905-72-321 18 SETTING MANDREL 905-70-750 905-72-750
7 UPPER SLIP 905-70-111 (4) 905-70-111 (4) 19 SETTING CYLINDER 905-70-755 905-70-755
8 SLIP SPRING* 905-55-900 (16) 905-55-900 (16) 20 LOCKING NUT* 905-70-720 905-70-720
9 TORQUE SCREW* 905-75-910 (4) 905-75-910 (4) 21 O-RING* 050-90-160 050-90-160
10 SHEAR SCREW* B20-C6-006 (8) B20-C6-006 (8) 22 LOWER CONE 905-70-421 905-72-421
11 UPPER CONE 905-70-411 905-72-411 23 LOWER SLIP 905-70-125 (4) 905-70-125 (4)
12 O-RING* 050-90-229 (6) 050-90-229 (6) 24 LOWER SLIP BODY 905-70-316 905-72-316
25 PICK-UP RING 905-70-760 905-70-760
DIMENSIONAL DATA 26 LOWER SLIP BODY CAP 907-70-345 907-70-345
27 RELEASE SCREW* 4,250 LB.EA. 650-50-902 (7) 650-50-902 (7)
DIMENSIONS (IN.) 28 SHEAR SLEEVE 905-70-740 905-70-740
SIZE PRODUCT
(IN.) NUMBER A B C D E F 29 CHANGE-OVER SUB 650-50-670 650-50-670
30 CHANGE-OVER SUB 650-50-670 650-50-670
7 905-70A-SSS 98.169 70.385 21.551 2.156 1.938 5.938 *Common repair parts
7 905-72A-SSS 98.169 70.171 21.551 2.156 1.938 6.000

© 1999 WEATHERFORD All Rights Reserved. NORTH AMERICAN NUMBERS: HUNTSVILLE, TX PH:800/331-4042 USA 409/295-0080 FAX:409/295-9132 • POWELL, WY PH:307/754-7234 800/458-9202 USA FAX:307/754-5875 REV. 00/DTD: 09-30-99
 INDEX NO.: 200
UNIT NO.: 905-70A-SSS
PN: 905-70A-SSS
905-72A-SSS
PAGE: 3 OF 3

7” HYDROW II-AP TEST OPERATING PROCEDURES

O-RING PRESSURE TEST KIT
1.) Plug the top and bottom of the short string side of the packer.
2.) Fill the mandrel with hydraulic oil or inhibited water.
ASSEMBLY
3.) Apply pressure, hold and observe for leaks. DO NOT EXCEED 1,500 P.S.I.
1.) Remove setting shear screws (16) from setting cylinder (19). 4.) Release pressure, remove test fixtures, and re-install setting shear screws (16) into setting
2.) Slide one sleeve cap (31) onto lower end of packer with threads toward bottom of tool. cylinder (19).
3.) Slide sleeve (33) onto lower end of packer.
4.) Install one (2 halves) split ring (32) into groove in setting mandrel (18) of packer. Slide sleeve PARTS LIST
(33) over split ring (32) and screw sleeve cap (31) into sleeve (33).
5.) Slide sleeve toward top of the packer enough to install remaining split ring (32) into groove in ITEM 7"
DESCRIPTION
lower cone (22) of packer. NUMBER 905-70-TSFA
6.) Slide remaining sleeve cap (31) onto lower end of packer and screw into sleeve (33). 31 SLEEVE CAP 905-70-TSF3 (2)
32 SPLIT RING (2 HALVES) 905-70-TSF4 (2)
33 TEST SLEEVE 905-70-TSF2

© 1999 WEATHERFORD All Rights Reserved. NORTH AMERICAN NUMBERS: HUNTSVILLE, TX PH:800/331-4042 USA 409/295-0080 FAX:409/295-9132 • POWELL, WY PH:307/754-7234 800/458-9202 USA FAX:307/754-5875 REV. 00/DTD: 09-30-99