Torsion Test: Department of Power Engineering and Turbomachinery Silesian University of Technology, Gliwice

Department of Power Engineering and Turbomachinery
Silesian University of Technology, Gliwice
INSTRUCTIONS FOR LABORATORY EXERCISES OF

STRENGTH OF MATERIALS
TORSION TEST
Dr inż. Katarzyna Stolecka
Gliwice, 2018
1) The aim of the laboratory
The purpose of the exercise is to find the modulus of elasticity in shear G (rigidity modulus) of the
material of which a bar with a cross-section is made, by measuring the angle of twist. The second
purpose of the exercise is determination of the characteristics of Ms=f(ϕ) (dependence of the torque
(twist moment) versus angle of twist).
2) Introduction
Torsion occurs when the twisting moments are applied to the bar.
Torsion is induced by two pairs of forces. These two forces act in two different planes perpendicular to
the axis of the bar. Moments of these two forces are called twisting moments.
If the bar is loaded by two pairs of forces of equally magnitudes moments but opposite directions in
two planes which are perpendicular to the axis then we obtained the state of strain and stress called
pure torsion – fig. 1.
Fig. 1. Models of pure torsion
Considering a simplified model of the bar. And then, assuming a three-dimensional grid and
subjecting to a pure torsion, it can be seen that (Fig. 2):
 the axis of the bar does not change its form and after deformation still remains straight line
 the circles remain wheels, and the cross-sectional ends are flat
 the horizontal lines of the grid will change its initial shape. This means that these lines are
deflected from their initial position by an angle γ
 the surfaces of the front and end of the bar will rotate relative to each other by an angle of
twist ϕ
Fig. 2. Deformation of the twisted bar of circular/square cross-section
3) Calculations
If we cut a segment of the bar with height dx and we assume some certain simplifications we can
evaluate the angle of twist of the bar section with height dx and radius r as:
𝑴𝒔 𝒅𝒙
𝒅𝝋 =
𝑮𝑱𝟎
The angle of twist for entire length of the bar can be expressed as:
𝑴𝒔 𝑳
𝝋=
𝑮𝑱𝟎
𝝅𝒅𝟒
𝑱𝟎 =
𝟑𝟐
Where:
Ms – torsion moment (torque)
dx –the height of the section of the bar
L – length of the bar
G – shear modulus, also called the rigidity modulus
J0 – polar moment of inertia
d – diameter of the bar

Shear stress
Shear stresses are produced by the application the twisting moments to the end of the bar. Shear stress
in sections orthogonal to the axis of the torsional bar can be expressed as:
𝑴𝒔
𝝉𝝆 = 𝝆
𝑱𝟎
The highest shear stress occurs on the surface of the bar, where the radius is maximum.
𝑴𝒔
𝝉𝒎𝒂𝒙 = 𝝉𝝆=𝒓 = 𝒓
𝑱𝟎
𝑱𝟎
= 𝑾𝟎
𝒓
𝑴𝒔
𝝉𝒎𝒂𝒙 = ≤ 𝝉𝒅𝒐𝒑
𝑾𝟎
𝝅𝒅𝟑
W0 – section modulus of torsion 𝑾𝟎 =
𝟏𝟔
τdop – permissible stress
NOTE: Above formulas are valid for the bar of circular cross-section in the area of stress falling below
the proportional limit (Fig. 3).
Fig. 3. The torque-twist plot of a torsion specimen
Mh – torque corresponding to the proportional limit stress

Msp – torque corresponding to the elastic limit stress
Mpl – torque corresponding to the yield stress
Mrs – torque corresponding to the fracture (rupture strength)
In the torsion bar, a change of stress in the circular cross-section can be observed. Graph of shear
stress to the proportional limit takes the form of a right triangle. After crossing the proportional limit,
the triangular form of a graph passes in a rectangular form, where the shear stress corresponding to the
yield stress already exists in the entire cross-section of the bar (see Fig. 4). The change of distribution
of stresses (from triangular to rectangular) results from shifting the first layers of the external cross-
section of the specimen beyond its yield stress. While the layers closer to the axis still remain in the
elastic region.
Fig. 4. Shear stress in the twisted bar of circular cross-section: a) elastic region, b) elastic-plastic
region, c) plastic region
4) Torsion test
Torsion test is usually carried out in the specimens of the circular cross-section for which determine
the state of stress and strain is relatively simple. Specimens with different cross-sections are used for
special tests. In this time, it is required to use different formulas than in the presented above. In the
case of solid specimens of circular cross-section the gauge length of the bar is equal to (5–20)d0,
generally l=10d0 where d0=(10-30)mm is a gauge diameter of specimen.
Fig 5. Specimens for torsion test
During the destructive torsion test, torsion fracture geometry may take the following forms:
a) When subjected to torsion a ductile specimen breaks along the plane perpendicular to the bar
axis
b) When subjected to torsion a brittle material breaks along the plane perpendicular to the
direction in which the tension is maximum
a) A solid bar of ductile. Facture on the plane right section

b) A solid bar of brittle. Helicoidally facture
5) Determination of shear modulus G (modulus of rigidity)
Scheme of the test stand is shown in Fig.6.
For solid circular torsion shafts:
𝝅𝒅𝟐
𝑱𝟎 = 𝟑𝟐
so:
𝟑𝟐𝑴𝒔 𝑳
𝑮=
𝝅𝒅𝟒 𝝋
Where:
𝒙
𝝋 ≅ 𝒂𝒓𝒕𝒄 [°]
𝒍𝒑
φ – the angle of twist

x – the displacement of the end of the spindle sensor caused by the angle of twist
lp – the distance between the spindle sensor and axis of the shafts
6) Torsion test
To perform the measurement do the following:
1) Set the sensor to zero.

2) Put the weight on the plate. The greater weights causes the increasing of the torque.
3) Each time make a response of sensor reading and written in measurement card.
4) After reaching the maximum load take off the weight and also write a response of the sensor.
7) Laboratory report
The laboratory’s report should contain:
a) A short introduction to torsion test

b) Brief description of the aim of the laboratory
c) Calculations
d) The formula for angle of twist
e) Plot of function Ms = f(φ)
f) Scheme of a test stand
g) Complete measurement card
h) Short conclusions.
Deadline for a laboratory report is 2 weeks.

Date of the laboratory:
Section:
Name Surname
Measurement data
lp = 90 mm (see fig. 6)
lr = 700 mm (see fig. 6)
length of specimen l = 500 mm
diameter of specimen d = 20 mm
𝟏
Lp. m [kg] x [mm] Ms = m·lr·g [N] φ [ ○] Gi [MPa] 𝑮𝒂𝒗 = ∑ 𝑮𝒊
𝒏
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.

Torsion Test: Department of Power Engineering and Turbomachinery Silesian University of Technology, Gliwice

Uploaded by

Copyright:

Available Formats

Torsion Test: Department of Power Engineering and Turbomachinery Silesian University of Technology, Gliwice

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Torsion Test: Department of Power Engineering and Turbomachinery Silesian University of Technology, Gliwice

Uploaded by

Copyright:

Available Formats

Department of Power Engineering and Turbomachinery

Silesian University of Technology, Gliwice

INSTRUCTIONS FOR LABORATORY EXERCISES OF

Dr inż. Katarzyna Stolecka

Fig. 1. Models of pure torsion

Ms – torsion moment (torque)

dx –the height of the section of the bar

L – length of the bar

G – shear modulus, also called the rigidity modulus

J0 – polar moment of inertia

d – diameter of the bar

τdop – permissible stress

Fig. 3. The torque-twist plot of a torsion specimen

Mh – torque corresponding to the proportional limit stress

Fig 5. Specimens for torsion test

a) A solid bar of ductile. Facture on the plane right section

5) Determination of shear modulus G (modulus of rigidity)

Scheme of the test stand is shown in Fig.6.

For solid circular torsion shafts:

φ – the angle of twist

To perform the measurement do the following:

1) Set the sensor to zero.

The laboratory’s report should contain:

a) A short introduction to torsion test

Deadline for a laboratory report is 2 weeks.

You might also like