Data SheetSP 5A-25
Data SheetSP 5A-25
Data SheetSP 5A-25
Submersible borehole pump, suitable for pumping clean water. Can be installed vertically or horizontally. All steel
components are made in stainless steel, EN 1.4301 (AISI 304), that ensures high corrosive resistance. This pump
carries drinking water approval.
The pump is fitted with a 2.2 kW MS402 motor with sand shield, lip seal, water-lubricated journal bearings and a
volume compensating diaphragm. The motor is a canned type submersible motor offering good mechanical stability
and high efficiency. Suitable for temperatures up to 40 °C.
The motor is not fitted with a temperature sensor. If temperature monitoring is desired, a Pt1000 sensor can be fitted.
Pump
All pump surfaces that are in contact with pumped liquids are made in stainless steel which makes them corrosion-
and wear-resistant. The corrosion diagram below shows the capabilities of the pump and motor in relation to the
temperature in Celsius (y-axis) and the concentration of chloride in ppm (x-axis).
The elastomer parts in the pump are made of NBR (Nitrile-Butadiene Rubber) and TPU (Thermoplastic Poly-Urethane) which offers
good wear resistance and long service intervals.
The suction interconnector is fitted with a strainer to prevent large particles from entering the pump. The suction
interconnector is designed to comply with NEMA standards for motor mounting/dimensions.
Motor
The stator is hermetically encapsulated in stainless steel and the windings are embedded in polymer compound. This
results in high mechanical stability, optimum cooling and reduces the risk of short circuits in the windings.
The shaft seal is of the lip seal type characterised by low friction against the rotor shaft. The NBR elastomer offers
good wear resistance, good elasticity and resistance to particles. The rubber material is approved for use in potable
water.
The motor can be fitted with a Pt100 or Pt1000 sensor that together with a control unit ensures that the maximum
operating temperature conditions are not exceeded.
Liquid:
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Selected liquid temperature: 20 °C
Density: 998.2 kg/m³
Technical:
Pump speed on which pump data are based: 2900 rpm
Actual calculated flow: 4.956 m³/h
Resulting head of the pump: 100.2 m
Shaft seal for motor: LIPSEAL
Approvals on nameplate: CE,EAC
Curve tolerance: ISO9906:2012 3B
Motor version: T40
Specification for shaft end: CYLINDRICAL
Materials:
Pump: Stainless steel
EN 1.4301
AISI 304
Impeller: Stainless steel
EN 1.4301
AISI 304
Motor: Stainless steel
DIN W.-Nr. 1.4301
AISI 304
Installation:
Pump outlet: Rp1 1/2
Motor diameter: 4 inch
Others:
Minimum efficiency index, MEI ≥: 0.50
ErP status: EuP Standalone/Prod.
Net weight: 19.6 kg
Gross weight: 21.3 kg
Shipping volume: 21.7 m³
Danish VVS No.: 388315250
Swedish RSK No.: 5852974
Finnish LVI No.: 4762678
Norwegian NRF no.: 9040877
On request SP 5A-25 50 Hz
H SP 5A-25, 3*400 V, 50Hz eta
[m] [%]
Q = 4.956 m³/h
H = 100.2 m
Es = 0.621 kWh/m³
n = 2852 rpm
Pumped liquid = Water
Liquid temperature during operation = 20 °C
Density = 998.2 kg/m³
160
140
120
100 100
80 80
60 60
40 40
20 20
3.5
3.0 P1
2.5
P2
2.0
1.5
1.0
0.5
P1 = 3.077 kW
P2 = 2.32 kW
0
95
1069
720.2
Rp1 1/2
101
Installation: 101
Pump outlet: Rp1 1/2
Rp1 1/2
Motor diameter: 4 inch
Liquid:
Pumped liquid: Water
Maximum liquid temperature: 40 °C
720.2
Electrical data:
Motor type: MS402
Applic. motor: GRUNDFOS
349
95
Rated power - P2: 2.2 kW
Power (P2) required by pump: 2.2 kW
Mains frequency: 50 Hz
Rated voltage: 3 x 380-400-415 V
L1 L2 L3 PE
Rated current: 5.50-5.50-5.70 A
Starting current: 440-460-470 %
Cos phi - power factor: 0.85-0.82-0.77
Rated speed: 2850-2860-2870 rpm
Start. method: direct-on-line
Enclosure class (IEC 34-5): IP68
Insulation class (IEC 85): B
Motor protec: NONE
Thermal protec: external
U V W PE
Built-in temp. transmitter: no
Motor No: 79192007
Others: M
Minimum efficiency index, MEI ≥: 0.50 3
On request SP 5A-25 50 Hz
cos phi SP5A-25 + MS402 2.2 kW 3*400 V, 50 Hz I
eta [A]
cos phi
0.8 8
eta
0.6 6
I
0.4 4
0.2 2
P2 = 2.32 kW
cos phi = 0.83
Eta = 75.4 %
I = 5.35 A
0.0 0
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 P2 [kW]
n P1
[rpm] [kW]
n
2800 4.0
P1
2600 3.0
2400 2.0
2200 1.0
P1 = 3.077 kW
n = 2852 rpm
2000 0.0
On request SP 5A-25 50 Hz
101
Rp1 1/2
720.2
1069
349
95
On request SP 5A-25 50 Hz
L1 L2 L3 PE
U V W PE
M
3