DX-3300-3800-75-15.

5i-M-R
Model: ATD4516R8

Antenna Specifications
General Electrical Properties
Frequency range (MHz) 3300 - 3800

General Polarization +45° , -45°

parameters Electrical downtilt (°) 2 - 12，continuously adjustable
Grounding DC Ground
Coupling factor between calibration port and each
-26 ±2
antenna port (dB)
Max. amplitude tolerance from calibration port to
0.9
input ports (dB)

Calibration and Max. phase tolerance from calibration port to input 7

electrical ports (°)
parameters
Ports VSWR 1.5
Avg. power capacity (W) 25
Co-polarization isolation between ports (dB) ≥ 20
Cross-polarization isolation between ports (dB) ≥ 25

Beamforming Electrical Properties

Frequency range (MHz) 3300 - 3800
Horizontal 3dB beam width (°) 78
Gain (dBi) 15.5

Single Vertical 3dB beam width (°) 5.5

column Cross polar ratio (0°) (dB) ≥ 18
beam
Side lobe suppression for first side
≤ -15
lobe above main beam (dB)
Front to back ratio (dB) ≥ 23
Horizontal 3dB beam width (°) 65
Gain (dBi) 17
Gain roll-off at sector edge (dB) 12
Radiation 65°
Vertical 3dB beam width (°) 5.5
parameters Broadcast
beam Cross polar ratio (0°) (dB) 22
Front to back ratio (dB) ≥ 25
Side lobe suppression for first side
≤ -15
lobe above main beam (dB)
0° direct beam gain (dBi) 21
0° direction beam horizontal 3dB
26
beam width (°)
0° direction beam horizontal side
Service -12
lobe suppression (dB)
beam
0° direction beam cross polar ratio
22
(0°) (dB)
0° direction beam front to back ratio
28
(dB)

1
 DX-3300-3800-75-15.5i-M-R
Model: ATD4516R8

Soft Split Electrical Properties

Frequency range (MHz) 3300 - 3800
Horizontal 3dB beam width (°) 30
Gain (dBi) 20
Radiation
parameters Vertical 3dB beam width (°) 5.5
Multi-beam
Front to back ratio (dB) ≥ 25
Side lobe suppression for first side
≤ -15
lobe above main beam (dB)

Notes：
65° broadcast beams and multi-beams are applicable in different scenarios. Select one of them for network coverage based on
site requirements and auxiliary equipment conditions.

Mechanical Properties
Distance between columns (mm) 43
Antenna dimensions (H x W x D) (mm) 1100 x 259 x 135 106

Packing dimensions (H x W x D) (mm) 1290 x 340 x 205

Antenna weight (kg) 13.0
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 20.0 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass

1100
770
Radome colour Light grey
Operational temperature (℃) -40 .. +65
Frontal: 350 (at 150 km/h)
Wind load (N) Lateral: 160 (at 150 km/h)
Rear side: 435 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 9 x N Female
Connector position Bottom

Accessories

Item Model Description Weight Units per antenna

Downtilt kit ASMDT0B01 Mechanical downtilt: 0 - 16° 1.3 kg 1 (Separate packing)

RET S/N: HWMxxx….y

RAE S/N: HWXxxx…..y

y - Yellow

2
 DX-3300-3800-75-15.5i-M-R
Model: ATD4516R8

Pattern sample for reference

Single 65°
column Broadcast

Service 0°

Azimuth Azimuth
-15° +15°

Multi-Beam Multi-Beam
-30° +30°

3
 DX-3300-3800-75-15.5i-M-R
Model: ATD4516R8

Antenna Information Management Module (AIMM) Specifications

RET Properties
RET type Integrated RET
RET protocols AISG 2.0 / 3GPP
Input voltage range (V) DC 10 - 30
< 6 (motor activated, 12V)
Power consumption (W)
< 1.5 (stand by, 12V)
Adjustment time (full range) (s) Typ. < 55
RET interface 1 (RF feeder) Calibration channel integrate the Bias-T and supporting OOK modulation signal communication
2 x 8 pin connector according to IEC 60130-9
RET interface 2 (485 connector)
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
Lightning protection (kA) 5 (8/20 μs)

RAE Properties
RAE type Integrated RAE, manages antenna information
RAE protocols AISG-ES-RAE V2.1.0

EasyBeam Properties
Frequency range (MHz) 3300 - 3800
Electrical downtilt (°) 2 - 12
Horizontal 3dB beam width (°) 30 65 90
Broadcast
Electrical azimuth (°) -15..+15 0
beam
Electrical azimuth step(°) 1 /

Standards: EN 55022(Emission), EN 55024(Immunity), ETSI EN 301 489, FCC part15, ICES-003

Certification: CE, FCC, IC

NOTE
1. Facilities, such as towers and poles, must bear the weight and wind load of antennas.
2. HUAWEI ‘s standard brackets and accessories must be used for any installation.
3. The antenna working environment must meet the requirements specified in the datasheet.
4. Only qualified personnel are allowed to perform installation. Installation tools and procedures must conform to
requirements described in the antenna installation guide.

Huawei Technologies Co., Ltd. Bantian, Longgang District, Shenzhen 518129, P.R.China www.huawei.com/antenna
Any previous datasheet issues become invalid. 4 Issue: 2016-06-22