0% found this document useful (0 votes)

87 views

MT

This document provides information on hydraulic orbit motors of the MS series. It describes their general features such as disc valve and roll-gerotor gearing which provide high efficiency. Standard motors can be mounted in various ways including on wheels. Options include short motors, speed sensors and drum brakes. Technical specifications are given for pressure, flow, torque, speed and temperature ranges. Mounting dimensions and order codes are also included.

Uploaded by

Даниил Сторчеус

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

87 views

MT

Uploaded by

Даниил Сторчеус

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 56

DISC VALVE HYDRAULIC MOTORS

CONTENTS

Page

• Hydraulic Motors Series MS .................................................................................... 4

• Hydraulic Motors Series MT ................................................................................... 25

• Hydraulic Motors Series MV .................................................................................. 39

• Motor Special Features............................................................................................... 51

• Motors with Speed Sensor................................................................................................... 52

• Application Calculation ....................................................................................................... 54

“M+S HYDRAULIC” can accept no responsibility for possible errors in catalogues, brochures and other printed material.
“M+S HYDRAULIC” reserves the right to alter its products without notice. This also applies to products already on order provided that such
alterations can be made without subsequential changes being necessary in specifications already agreed.
DISC VALVE HYDRAULIC MOTORS
GENERAL INFORMATION:
Orbit motors convert hydraulic energy (pressure, oil flow) into mechanical energy (torque, speed). Hydraulic orbit motors
operate on the principle of an internal gear (rotor) rotating within a fixed external gear (stator). The internal gear transmits
the torque generated by the application of pressure from hydraulic oil fed into motor which is then delivered via the motor's
output shaft. Orbit motors have high starting torque and constant output torque at wide speed range. The output shaft runs
on tapered roller bearings and can absorb high axial and radial forces.

DISTRIBUTOR VALVE
MS, MT, MV series motors have disk valve: the distributor valve has been separated from output shaft and is driven by short
cardan shaft. A balance plate counterbalances the hydraulic forces around the distributor valve. It gives the motors high
efficiency- even at high pressures, and good starting characteristics.

GEAR WHEEL SET

There are two forms of gear wheel set: Gerotor set has plain teeth and Roll-gerotor set with teeth fitted with rollers.
MS, MT, MV series motors have roll-gerotor set. The rollers reduce local stress and the tangential reaction forces on the
rotor reducing friction to a minimum. This gives long operating life and better efficiency even at continuous high pressures.

FEATURES:

Standard Motor The standard motor mounting flange is located as close to the output shaft as possible. This type of
mounting supports the motor close to the shaft load. This mounting flange is also compatible with many standard gear
boxes.

Wheel Motor The wheel motor mounting flange is located near the center of the motor which permits part or all of
the motor to be located inside the wheel or roller hub. In traction drive applications, loads can be positioned over the motor
bearings for best bearing life. This wheel motor mounting flange provides design flexibility in many applications.

Short Motor This motor is assembled without the output shaft, bearings and bearing housing and has the same
drive components as the standard motors. The short motor is especially suited for applications such as gear boxes, winch,
reel and roll drives. Short motor applications must be designed with a bearing supported internal spline to mate with the
short motor drive. Product designs using these hydraulic motors provide considerable cost savings.

Low Leakage LL Series hydraulic motors are designed to operate at the whole standard range of working
conditions (pressure drop and frequency of rotation ), but with considerable decreased volumetric losses in the drain
ports. This motors are suitable for hydraulic systems with series-conected motors with demands for low leakage.

Low Speed LSV feature optimizes the motor for low-speed performance. Motors with this valving provide very
Valve low speed while maintaining high torque. They are designed to run continuously at low speed (up to
200 RPM) at normal pressure drop and reduced flow. Optimal run is guaranteed at frequency of rotation from 20 to 50 RPM.
Motors with this valving have an increased starting pressure and are not recommended for using at pressure drop less than
40 bar.

High Pressure The high pressure shaft seals allow the motors to withstand high case pressures at high speeds
Shaft Seal without external drain line.

Motors with Motors are available with integrated inductive speed sensor. The output signal is a standardized
Speed Sensor voltage signal that can be used to control the speed of a motor. The torque and the radial load of the
motor are not affected by the installation of speed sensor.

3
HYDRAULIC MOTORS MS

APPLICATION
» Conveyors
» Metal working machines
» Agricultural machines
» Road building machines
» Mining machinery
» Food industries
» Special vehicles etc.

CONTENTS OPTIONS
Specification data ............................................ 5÷6 » Model - Disc valve, roll-gerotor
Function diagrams ........................................ 7÷12
» Flange and wheel mount
Dimensions and mounting ...........................13÷16
Tacho connection ............................................. 16 » Short motor
Shaft extensions .............................................. 17 » Motor with Drum Brake
Motor with Drum brake- MSB .......................... 18 » Tacho connection
Permissible Shaft Seal pressure........................17
» Speed sensoring
Permissible shaft loads ................................... 19
Function diagram for MSB .............................. 19 » Side and rear ports
Dimensions and mounting- MSS, V, U ...... 20÷23 » Shafts - straight, splined and tapered
Internal Spline data ......................................... 23 » SAE, Metric and BSPP ports
Order code ...................................................... 24
» Other special features

GENERAL
Max. Displacement, 3
cm /rev [in /rev]
3
564,9 [34.47]
Max. Speed, [RPM] 1000
Max. Torque, daNm [lb-in] cont.: 85 [7520] int.: 99 [8760]
Max. Output, kW [HP] 23 [30.8]
Max. Pressure Drop, bar [PSI] cont.: 210 [3050] int.: 275 [3990]
Max. Oil Flow, lpm [GPM] 90 [24]
Min. Speed, [RPM] 5
Permissible Shaft Loads daN [lbs] Pa=500 [1125]
Pressure fluid Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)
Temperature range,
O O
C [ F] -40÷140 [-40÷284]
Optimal Viscosity range, mm /s [SUS]
2
20÷75 [98÷347]
Filtration ISO code 20/16 (Min. recommended fluid filtration of 25 microns)

Oil flow in drain line p p Pressure Losses

bar PSI
14 200
12
Oil flow in 150
Pressure drop Viscosity drain line 10
2
bar [PSI] mm /s [ SUS] lpm [GPM ] 8
100
6
20 [ 98 ] 1,5 [ .396 ]
140 [2030] 4 50
35 [ 164 ] 1 [ .264 ]
2
20 [98] 3 [ .793 ] 0 0
210 [ 3045]
35 [164] 2 [ .528 ] 0 2.5 5 7.5 10 12.5 15 17.5 20 22.5 Q, GPM

0 10 20 30 40 50 60 70 80 90 Q, lpm

4
MS
MOTORS

SPECIFICATION DATA

Type MS 80 MS 100 MS 125 MS 160 MS 200

Displacement, cm³/rev [in³/rev] 80,5 [4.91] 100 [6.1] 125,7 [7.67] 159,7 [9.74] 200 [12.2]
Max. Speed, cont. 810 750 600 470 375
[RPM] Int.* 1000 900 720 560 450
Max. Torque cont. 24 [2120] 30,5 [2700] 37,5 [3320] 49 [4340] 61 [5400]
daNm [lb-in] Int.* 31 [2740] 39 [3450] 49 [4340] 60 [5310] 72 [6370]
Max. Output cont. 15,5 [20.8] 18 [24.1] 18 [24.1] 16,5 [22.1] 16,5 [22.1]
kW [HP] int.* 19,5 [26.2] 22,8 [30.2] 22,5 [30.2] 23 [30.8] 22 [29.52]
Max. Pressure Drop cont. 210 [3050] 210 [3050] 210 [3050] 210 [3050] 210 [3050]
bar [PSI] Int.* 275 [3990] 275 [3990] 275 [3990] 275 [3990] 275 [3990]
peak** 295 [4280] 295 [4280] 295 [4280] 295 [4280] 295 [4280]
Max. Oil Flow cont. 65 [17] 75 [20] 75 [20] 75 [20] 75 [20]
lpm [GPM] Int.* 80 [21] 90 [24] 90 [24] 90 [24] 90 [24]
Max. Inlet Pressure cont. 230 [3340] 230 [3340] 230 [3340] 230 [3340] 230 [3340]
bar [PSI] Int.* 295 [4280] 295 [4280] 295 [4280] 295 [4280] 295 [4280]
peak** 300 [4350] 300 [4350] 300 [4350] 300 [4350] 300 [4350]
Max. Return Pressure cont. 140 [2030] 140 [2030] 140 [2030] 140 [2030] 140 [2030]
with Drain Line Int.* 175 [2540] 175 [2540] 175 [2540] 175 [2540] 175 [2540]
bar [PSI] peak** 210 [3050] 210 [3050] 210 [3050] 210 [3050] 210 [3050]
Max. Starting Pressure with Unloaded Shaft, bar [PSI] 12 [175] 10 [145] 10 [145] 8 [115] 8 [115]
Min. Starting Torque at max. press. drop cont. 18 [1590] 23 [2040] 29 [2570] 37 [3270] 47 [4160]
daNm [lb-in] at max. press. drop Int.* 23,5 [2080] 30 [2660] 38 [3360] 46 [4070] 56 [4960]
Min. Speed***, [RPM] 10 10 8 8 6
Weight, kg [lb] MS(F) 9,9 [21.8] 10,1 [22.2] 10,4 [22.9] 10,8 [23.8] 11,2 [24.7]
MSW 10,4 [22.9] 10,6 [23.3] 10,9 [24] 11,3 [24.6] 11,7 [25.8]
For Rear Ports
MSS 7,9 [17.4] 8,1 [17.8] 8,4 [18.5] 8,8 [19.4] 9,2 [20.2]
+ 0,40 [.88]
MSV 5,8 [12.8] 6 [13.2] 6,3 [13.9] 6,7 [14.8] 7,1 [15.6]
MSQ 10,3 [22.7] 10,5 [23.2] 10,8 [23.8] 11,2 [24.7] 11,6 [25.6]
MSB 16,9 [37.3] 17,1 [37.7] 17,4 [38.3] 17,8 [39.2] 18,2 [41.1]

* Intermittent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds lower than given, consult factory or your regional manager.

1. Intermittent speed and intermittent pressure must not occur simultaneously.

2. Recommended filtration is per ISO cleanliness code 20/16. A nominal f iltration of 25 micron or better.
3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM ( ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4. Recommended minimum oil viscosity 13 mm²/s [70 SUS] at 50°C [122°F].
5. Recommended maximum system operating temperature is 82°C [180°F].
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.

5
MSMS
MOTORS
MOTORS

SPECIFICATION DATA (continued)

Type MS 250 MS 315 MS 400 MS 475 MS 525 MS 565

Displacement, cm³/rev [in³/rev] 250 [15.3] 314,9 [19.2] 397 [24.2] 474,6[28.96] 522,7 [31.88] 564,9[34.47]
Max. Speed, cont. 300 240 190 160 145 130
[RPM] Int.* 360 290 230 190 175 160
Max. Torque cont. 72 [6370] 82,5 [7300] 86,5 [7660] 85 [7520] 85 [7520] 85 [7520]
daNm [lb-in] Int.* 87 [7700] 100 [8850] 99 [8760] 99 [8760] 99 [8760] 99 [8760]
Max. Output cont. 14,5 [19.4] 15 [20.1] 11 [14.8] 8,4 [11] 7,6 [10.2] 6,9 [9]
kW [HP] int.* 18 [24.1] 17 [22.8] 12,5 [16.8] 11,3 [15] 10,4 [13.9] 9,6 [13]
Max. Pressure Drop cont. 200 [2900] 200 [2900] 160 [2320] 130 [1880] 115 [1670] 105 [1520]
bar [PSI] Int.* 250 [3630] 240 [3480] 190 [2760] 150 [2180] 135 [1960] 125 [1810]
peak** 270 [3920] 260 [3770] 210 [3050] 170 [2470] 155 [2250] 145 [2100]
Max. Oil Flow cont. 75 [20] 75 [20] 75 [20] 75 [20] 75 [20] 75 [20]
lpm [GPM] Int.* 90 [24] 90 [24] 90 [24] 90 [24] 90 [24] 90 [24]
Max. Inlet Pressure cont. 230 [3340] 230 [3340] 230 [3340] 230 [3340] 230 [3340] 230 [3340]
bar [PSI] Int.* 295 [4280] 295 [4280] 295 [4280] 295 [4280] 295 [4280] 295 [4280]
peak** 300 [4350] 300 [4350] 300 [4350] 300 [4350] 300 [4350] 300 [4350]
Max. Return Pressure cont. 140 [2030] 140 [2030] 140 [2030] 140 [2030] 140 [2030] 140 [2030]
with Drain Line Int.* 175 [2540] 175 [2540] 175 [2540] 175 [2540] 175 [2540] 175 [2540]
bar [PSI] peak** 210 [3050] 210 [3050] 210 [3050] 210 [3050] 210 [3050] 210 [3050]
Max. Starting Pressure with Unloaded Shaft, bar [PSI] 8 [115] 8 [115] 8 [115] 8 [115] 8 [115] 8 [115]
Min. Starting Torque at max. press. drop cont. 56 [4960] 71 [6280] 71 [6280] 71 [6280] 71 [6280] 71 [6280]
daNm [lb-in] at max. press. drop Int.* 70 [6200] 85 [7520] 84 [7430] 84 [7430] 84 [7430] 84 [7430]
Min. Speed***, [RPM] 6 5 5 5 5 5
Weight, kg [lb] MS(F) 11,7 [25.8] 12,4 [27.3] 13,1 [29.3] 14,1 [31] 14,6 [32.2] 15 [33.1]
MSW 12,2 [26.9] 12,9 [28.4] 13,8 [30.4] 14,6 [32.2] 15,1 [33.3] 15,5 [34.1]
For Rear Ports
MSS 9,7 [21.4] 10,4 [22.9] 11,3 [24.9] 12.1 [26.7] 12,6 [27.8] 13 [28.6]
+ 0,40 [.88]
MSV 7,6 [16.7] 8,3 [18.3] 9,2 [20.2] 10 [22] 10,5 [23.1] 10,9 [24]
MSQ 12,1 [26.7] 12,8 [28.2] 13,7 [30.2] 14,5 [32] 15 [33.1] 15,4 [33.9]
MSB 18,7 [41.2] 19,4 [42.7] 20,3 [44.7] 21,1 [46.5] 21,6 [47.6] 23 [48.5]

1. Intermittent speed and intermittent pressure must not occur simultaneously.

6
MS
MOTORS

FUNCTION DIAGRAMS

MS 80

M M

20 l/min
5.3 GPM

30 l/min
7.9 GPM

40 l/min
10.6 GPM

50 l/min
13.2 GPM

80 l/min
21.1 GPM
65 l/min
17.2 GPM
Q=5 l/min
1.3 GPM
10 l/min
2.6 GPM

lb-in daNm

3000
p=275 bar
30 3990 PSI
2500 250 bar
3630 PSI
18 kW 225 bar
25 3260 PSI
210 bar
int.

2000 9 kW 15 kW
12 kW 3050 PSI
20 175 bar
6 kW 12 hp 18 hp 2540 PSI
1500 9 hp
6 hp 15 hp
15 140 bar
1 hp 2030 PSI
3 kW
cont.

3 hp
1000 105 bar
10 t=81%
1520 PSI
80%
70 bar
500 78% 1020 PSI
5 N=1 kW 70%
75%
30 bar
60%
440 PSI
0 0
cont. int. n

0 100 200 300 400 500 600 700 800 900 1000 RPM

MS 100

M
60 l/min
15.9 GPM
10 l/min
2.6 GPM
Q=5 l/min
1.3 GPM

40 l/min
10.6 GPM

50 l/min
13.2 GPM
20 l/min
5.3 GPM

30 l/min
7.9 GPM

75 l/min
19.8 GPM

90 l/min
23.8 GPM

M daNm
lb-in

4000 45
p=275 bar
3500 40 3990 PSI
250 bar
35 3630 PSI
3000 15 kW 18 kW 225 bar
3260 PSI
int.

30 210 bar
2500 9 kW 12 kW 3050 PSI
25 175 bar
12 hp
2000 6 kW 9 hp 2540 PSI
15 hp 18 hp
20 140 bar
6 hp
3 kW 2030 PSI
cont.

1500 t=83%
15 105 bar
3 hp
1520 PSI
1000 80%
10
70 bar
1 hp N=1 kW 75% 1020 PSI
500 5 70%
35 bar
60% 510 PSI
0 0 cont. int. n
0 100 200 300 400 500 600 700 800 900 950 RPM

The function diagrams data is for average performance of randomly selected motors at back pressure
o
5÷10 bar [72.5÷145 PSI] and oil with viscosity of 32 mm²/s [150 SUS] at 50°C [122 F].
7
MS
MOTORS

FUNCTION DIAGRAMS

MS 125

M M
20 l/min
5.3 GPM

30 l/min
7.9 GPM

40 l/min
10.6 GPM

50 l/min
13.2 GPM

60 l/min
15.9 GPM

75 l/min
19.8 GPM

90 l/min
23.8 GPM
10 l/min
2.6 GPM
Q=5 l/min
1.3 GPM

lb-in daNm

4500
50 p=275 bar
3990 PSI
4000 45 250 bar
21 kW 3630 PSI
3500 40 225 bar
18 kW
int.

3260 PSI
12 kW 15 kW 210 bar
3000 35 3050 PSI
9 kW 21 hp
30 175 bar
2500 2540 PSI
6 kW 18 hp
25
cont.

6 hp 140 bar
2000 9 hp 15 hp
12 hp 2030 PSI
20
1500 3 hp 3 kW 105 bar
15 t=85% 83% 1520 PSI
1 hp 80%
1000 70 bar
10
N=1 kW 75% 1020 PSI
500 70%
5 35 bar
60%
510 PSI
0 0
cont. int. n

0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 RPM

MS 160

M M
Q=5 l/min
1.3 GPM
10 l/min
2.6 GPM

30 l/min
7.9 GPM

40 l/min
10.6 GPM

50 l/min
13.2 GPM
20 l/min
5.3 GPM

60 l/min
15.9 GPM

75 l/min
19.8 GPM

90 l/min
23.8 GPM

lb-in daNm
6000

60 p=260 bar
3770 PSI
5000
55
21 kW 225 bar
50 3260 PSI
4000 21 hp 18 kW 210 bar
45
int.

6 kW
3050 PSI
12 kW 15 kW
40 175 bar
2540 PSI
35 160 bar
3000 9 kW 18 hp 2320 PSI
30 140 bar
cont.

9 hp 12 hp 15 hp 2030 PSI
6 hp
25
2000 105 bar
3 hp 3 kW
20 1520 PSI
t=87%
15 1 hp
N=1 kW 86% 85% 83% 80% 70 bar
1000 10 1020 PSI
75% 70%
60%
5 35 bar
510 PSI
0 0
cont. int. n
0 50 100 150 200 250 300 350 400 450 500 550 600 RPM

MS 200

M M

40 l/min
10.6 GPM
20 l/min
5.3 GPM

30 l/min
7.9 GPM

60 l/min
15.9 GPM

75 l/min
19.8 GPM

90 l/min
23.8 GPM
50 l/min
13.2 GPM
10 l/min
2.6 GPM
Q=5 l/min
1.3 GPM

lb-in daNm

7000
75
p=250 bar
70 3630 PSI
6000
65 225 bar
int.

21 kW 3260 PSI
60 210 bar
15 kW 18 kW 3050 PSI
5000 55
12 kW 175 bar
50
21 hp 2540 PSI
4000 45 12 hp 160 bar
9 kW 2320 PSI
cont.

40 140 bar
6 kW 18 hp 2030 PSI
35 6 hp 9 hp
3000 15 hp
30 105 bar
t=88%
25 1520 PSI
2000 3 kW 86%
20
N=1 kW 3 hp 85% 70 bar
15 83% 80%
1 hp 75% 1020 PSI
1000 10 70%
60% 30 bar
5 440 PSI
0 0 cont. int. n

0 50 100 150 200 250 300 350 400 450 500 RPM

MS 250
50 l/min
13.2 GPM
20 l/min
5.3 GPM
10 l/min
2.6 GPM

30 l/min
7.9 GPM

40 l/min
10.6 GPM

75 l/min
19.8 GPM

90 l/min
23.8 GPM
Q=5 l/min
1.3 GPM

60 l/min
15.9 GPM

M M
lb-in daNm
p=250 bar
8000 90 3630 PSI

225 bar
80 3260 PSI
7000 21 kW
200 bar
int.

2900 PSI
70
6000 9 kW 15 kW 18 kW
175 bar
2540 PSI
60
5000 18 hp 21 hp 155 bar
2250 PSI
50
cont.

6 hp 9 hp 12 hp 15 hp 140 bar
4000 12 kW 2030 PSI
6 kW
40 125 bar
1810 PSI
3000 3 kW
3 hp 95 bar
30
86% 85% 1390 PSI
2000 70 bar
20 N=1 kW t=87%
83% 1020 PSI
1 hp 80% 75% 70%
1000 10 35 bar
60% 510 PSI
0 0
cont. int. n

0 50 100 150 200 250 300 350 RPM

MS 315

M M

75 l/min
19.8 GPM
30 l/min
7.9 GPM

40 l/min
10.6 GPM
20 l/min
5.3 GPM

60 l/min
15.9 GPM

90 l/min
23.8 GPM
50 l/min
13.2 GPM
10 l/min
2.6 GPM
Q=5 l/min
1.3 GPM

lb-in daNm

p=240 bar
9000 3480 PSI
100 225 bar
3260 PSI
8000 200 bar
90 2900 PSI
int.

18 kW 175 bar
7000 80
15 kW 2540 PSI
160 bar
70 2320 PSI
6000 12 kW
9 kW 15 hp 140 bar
60
cont.

12 hp 18 hp 2030 PSI
5000
6 kW 120 bar
50 1740 PSI
9 hp
4000
100 bar
40 1450 PSI
3 kW 6 hp
3000 t=87%
30 70 bar
1020 PSI
N=1 kW 3 hp 85% 80%
2000 83%
20 1 hp 75% 70%
1000 35 bar
10 60% 510 PSI

0 0
cont. int. n

0 25 50 75 100 125 150 175 200 225 250 275 300 RPM

MS 400

M M
40 l/min
10.6 GPM

75 l/min
19.8 GPM
20 l/min
5.3 GPM

30 l/min
7.9 GPM

60 l/min
15.9 GPM

90 l/min
23.8 GPM
50 l/min
13.2 GPM
10 l/min
2.6 GPM
Q=5 l/min
1.3 GPM

lb-in daNm

p=190 bar
9000 2760 PSI
100 175 bar
2540 PSI
8000 90 160 bar
int.

15 kW 2320 PSI
80 140 bar
7000
2030 PSI
12 kW
70 120 bar
6000
15 hp 1740 PSI
60 12 hp
cont.

5000 105 bar

3 kW 6 kW 9 kW 1520 PSI
50
4000 9 hp
t=87% 80 bar
40 6 hp
3 hp 1160 PSI
3000
30 85% 60 bar
N=1 kW 86% 83% 870 PSI
2000
20 1 hp 80%
75%
70%
30 bar
1000 10 440 PSI
60%
0 0
cont. int. n

0 25 50 75 100 125 150 175 200 225 250 RPM

FUNCTION DIAGRAMS

MS 475

M M

75 l/min
19.8 GPM
Q=5 l/min
1.3 GPM

30 l/min
7.9 GPM

40 l/min
10.6 GPM

60 l/min
15.9 GPM

90 l/min
23.8 GPM
20 l/min
5.3 GPM
10 l/min
2.6 GPM

50 l/min
13.2 GPM
lb-in daNm

9000 p=150 bar

100
2180 PSI
int.

8000 90 130 bar

1890 PSI
12 kW 120 bar
7000 80 1740 PSI
12 hp
70 105 bar
6000
6 hp 1520 PSI
cont.

60
5000 9 kW
50 3 kW 86% 85% 85 bar
t=88% 6 kW
4000 9 hp 1230 PSI
3 hp
40 83% 70 bar
3000 80% 1020 PSI
30 N=1 kW
1 hp 75% 70% 50 bar
2000 730 PSI
20 60%

1000 10
25 bar
360 PSI
0 0
cont. int. n

0 25 50 75 100 125 150 175 200 RPM

MS 525

M M
Q=5 l/min
1.3 GPM

30 l/min
7.9 GPM

40 l/min
10.6 GPM

50 l/min
13.2 GPM
20 l/min
5.3 GPM

60 l/min
15.9 GPM

75 l/min
19.8 GPM

90 l/min
23.8 GPM
10 l/min
2.6 GPM

lb-in daNm

9000 p=135 bar

100
1960 PSI
int.

8000 90 115 bar

1670 PSI
7000 80 105 bar
9 kW 1520 PSI
70 12 hp
6000
6 hp
cont.

6 kW 9 hp 90 bar
60
5000 3 kW 86% 1300 PSI
t=88% 80 bar
50 1160 PSI
4000 3 hp 85%
40
3000
30 N=1 kW 80% 50 bar
1 hp 83% 75% 730 PSI
2000 70%
20
60%
1000 10 25 bar
360 PSI
0 0
cont. int. n

0 25 50 75 100 125 150 175 RPM

FUNCTION DIAGRAMS

MS 565

M M
Q=5 l/min
1.3 GPM
10 l/min
2.6 GPM

20 l/min
5.3 GPM

30 l/min
7.9 GPM

40 l/min
10.6 GPM

50 l/min
13.2 GPM

60 l/min
15.9 GPM

75 l/min
19.8 GPM

90 l/min
23.8 GPM
lb-in daNm

9000 p=125 bar

100
1810 PSI
8000 90
int.

105 bar
80 1520 PSI
7000
12 hp 9 kW
9 hp
70
6000 6 hp 85 bar
6 kW 1230 PSI
60 3 kW
cont.

5000
50 t=88% 70 bar
1020 PSI
4000 3 hp 86% 85%
83% 60 bar
40 870 PSI
3000 80%
30 N=1 kW
45 bar
1 hp 650 PSI
2000 75%
20 30 bar
70%
60% 430 PSI
1000 10
15 bar
220 PSI
0 0
cont. int. n

0 20 40 60 80 100 120 140 160 RPM

The function diagrams data is for average performance of randomly selected motors at back pressure
o
5÷10 bar [72.5÷145 PSI] and oil with viscosity of 32 mm²/s [150 SUS] at 50°C [122 F].

12
MS
MOTORS
DIMENSIONS AND MOUNTING DATA
MS, MSF, MSA, MSW

SL Shaft SL Shaft
Shaft Dim.
See Page 17
K Shaft C Shaft K Shaft C Shaft
SH Shaft SH Shaft
CO Shaft CO Shaft
SA Shaft SA Shaft
110 [4.33]

146 [5.748]
67,85 [2.671]
67,85 [2.671]

57,85 [2.277]

104 [4.09]

94 [3.701]
104 [4.09]
42 [1.65]

78 [3.07]
65 [2.535]

[1.102]
28
L2

Flange Dim.
max L

See Page 15
T

L2
L1

L1
max 103 max 103
[4.055] max L [4.055]

Port A

Port B

Port Dim.
P(A,B) See Page 16

E Rear ports

mm [in]

C: 2xM10-12 mm [.47 in] depth

max LE

P(A,B): 2xG1/2 or 2xM22x1,5-15 mm [.59 in] depth

T: G ¼ or M14x1,5- 12 mm [.47 in] depth (plugged)

Standard Rotation Reverse Rotation

Viewed from Shaft End Viewed from Shaft End
Port A Pressurized - CW Port A Pressurized - CCW
Port A Port B
Port B Pressurized - CCW Port B Pressurized - CW

Type L,mm[in.] L2,mm[in.] *LE, mm[in.] Type L, mm[in.] L2,in.[mm] *LE,mm[in.] L1,mm[in.]
MS(F, A) 80 168 [6.61] 124 [4.88] 173 [6.81] MSW 80 129 [5.08] 87 [3.43] 138 [5.43] 14,0 [.55]
MS(F, A) 100 171 [6.73] 128 [5.04] 177 [6.97] MSW100 133 [5.23] 91 [3.58] 142 [5.59] 17,4 [.69]
MS(F, A) 125 176 [6.93] 132 [5.20] 181 [7.13] MSW 125 137 [5.39] 95 [3.74] 146 [5.75] 21,8 [.86]
MS(F, A) 160 182 [7.17] 138 [5.43] 187 [7.36] MSW 160 143 [5.63 ] 101 [3.98] 152 [5.99] 27,8 [1.09]
MS(F, A) 200 189 [7.44] 145 [5.71] 194 [7.64] MSW 200 150 [5.91] 108 [4.25] 159 [6.26] 34,8 [1.37]
MS(F, A) 250 197 [7.76] 154 [6.06] 203 [7.99] MSW 250 159 [6.26] 117 [4.61] 168 [6.62] 43,5 [1.71]
MS(F, A) 315 209 [8.23] 165 [6.50] 214 [8.43] MSW 315 170 [6.69] 128 [5.04] 179 [7.05] 54,8 [2.16]
MS(F, A) 400 223 [8.78] 179 [7.05] 228 [8.98] MSW 400 184 [7.24] 143 [5.63] 194 [7.64] 69,4 [2.73]
MS(F, A) 475 237 [9.33] 193 [7.60] 242 [9.53] MSW 475 198 [7.79] 156 [6.14] 207 [8.15] 82,6 [3.25]
MS(F, A) 525 229 [9.02] 185 [7.28] 234 [9.21] MSW 525 190 [7.48] 148 [5.83] 199 [7.84] 74,5 [2.93]
MS(F, A) 565 235 [9.25] 191 [7.52] 240 [9.45] MSW 565 196 [7.72] 154 [6.06] 205 [8.07] 80,2 [3.16]

* -For Rear Ported Motors.

13
MS
MOTORS
DIMENSIONS AND MOUNTING DATA - MSQ

SL Shaft

Shaft Dim.
K Shaft C Shaft See Page 17
SH Shaft CO Shaft
SA Shaft

96,5 [3.799]

44,35 [1.746]
54,35 [2.14]

54,35 [2.14]
28.5 [1.12]
[3.031]
77

L2
max L

L1
max 103
[4.055]

Port A
Port Dim.
Port B See Page 16

P(A,B)

E Rear ports
L2
max LE

mm [in]
Port A Port B

C: 2xM10-12 mm [.47 in] depth Standard Rotation Reverse Rotation

P(A,B): 2xG1/2 or 2xM22x1,5-15 mm [.59 in] depth Viewed from Shaft End Viewed from Shaft End
Port A Pressurized - CW Port A Pressurized - CCW
T: G ¼ or M14x1,5- 12 mm [.47 in] depth (plugged) Port B Pressurized - CCW Port B Pressurized - CW

Type L, mm [in.] L2, mm [in.] *LE, mm [in.] L1, mm [in.]

MSQ 80 179 [7.05] 136 [5.35] 185 [7.28] .55 [14,0]
MSQ 100 183 [7.21] 140 [5.51] 189 [7.44] .69 [17,4]
MSQ 125 187 [7.36] 144 [5.67] 193 [7.60] .86 [21,8]
MSQ 160 193 [7.60] 150 [5.91] 199 [7.83] 1.09 [27,8]
MSQ 200 200 [7.87] 157 [6.18] 206 [8.11] 1.37 [34,8]
MSQ 250 209 [8.23] 166 [6.54] 215 [8.46] 1.71 [43,5]
MSQ 315 220 [8.66] 177 [6.67] 226 [8.90] 2.16 [54,8]
MSQ 400 235 [9.25] 192 [7.56] 241 [9.49] 2.73 [69,4]
MSQ 475 247 [9.72] 205 [8.07] 254 [10.0] 3.25 [82,6]
MSQ 525 240 [9.45] 197 [7.76] 246 [9.69] 2.93 [74,5]
MSQ 565 246 [9.69] 203 [7.99] 252 [9.92] 3.16 [80,2]

* -For Rear Ported Motors.

14
MS
MOTORS

MOUNTING

SAE A-4 Mount (4 Holes)

4xø13,5
[.531] ø106,4±0,2 6,1±0,25
[4.189±.0078] [.24±.0098]

[3.248+.0019]
ø82,5 +0,05
Q Square Mount (4 Holes)
max 131
[5.157]

4xø11,5 ø106,4±0,2
ax 33 5

6,1±0,25
m 4.1 10

[.453] [4.189±.0078]
.9 26 ]
[ ax

[.24±.0098]
m

[4 1
6]

53 18
[2.086] [.709]

[3.248 +.0019]
ø82,5 +0,05
max 103
[4.055]

max 103 18
A SAE A-2 Mount (2 Holes) [4.055] [.709]

2xø13,5
[.531] ø106,4±0,2 6,1±0,25
[4.189±.0078] [.24±.0098]
[3.248 +.0019 ]
ø82,5 +0,05
max 131
[5.157]

ø95
[3.7
4]
W Wheel Mount
.9 26
[4 x 1
6]
a
m

53 18
[2.086] [.709]

16 9
ø160±0,2 [.629] [.354]
4xø13,5
[6.299±.0078] [.531]
[4.921-.0025 ]

F Magneto Mount (4 Holes)

ø125 -0,063
max 139

max ø73
[5.47]

[2.87]

4xø13,5
ø106,4±0,2 6,1±0,25
[.531]
[4.189±.0078] [.24±.0098]
43
max 139 [1.693]
[5.47]
[3.248 +.0019]
ø82,5+0,05
max 136
[5.35]

ø95
[3.7
4]

0
22,5 0 22,5 18
[.709]

mm [in]

15
MS
MOTORS

PORTS

Side Ports E Rear Ports

L2
53 5±0,15 22±0,3 53 Port B
[2.086] [.197±.0059] [.866±.0118]
C
[2.086]

[.63±.0118]
16±0,3

[1.26±.0118] [1.26±.0118]
[.827±.0118]

32±0,3
Port B

21±0,3
21±0,3

[.827±.0118]

32±0,3
Port A
[.63±.0118]
16±0,3

P(A,B)
5±0,15
[.197±.0059]
P(A,B)
max L
Port A

Standard Rotation Reverse Rotation

Viewed from Shaft End Viewed from Shaft End C: 2xM10-12 mm [.47 in] depth
Port A Pressurized - CW Port A Pressurized - CCW P(A,B): 2xG1/2 or 2xM22x1,5-15 mm [.59 in] depth
Port B Pressurized - CCW Port B Pressurized - CW T: G ¼ or M14x1,5- 12 mm [.47 in] depth (plugged)

MOTORS WITH TACHO CONNECTION

53 max L 33
[2.086] [1.299]
[.315]
ø8

ø3
[.118]
[1.89]
ø48

5
[.197]

16 20
ø34 4xM5
[1.339] 8 [.315] depth [.63] [.787]

mm [in]

16
MS
MOTORS
SHAFT EXTENSIONS

C - ø32 straight, Parallel key A10x8x45 DIN 6885 K - tapered 1:10, Parallel key B6x6x20 DIN 6885
Max. Torque 77 daNm [6815 lb-in] Max. Torque 95 daNm [8400 lb-in]
S=41
Tightening torque
A-A A 20±1 daNm
10 -0,036 6 -0,03 [1770±88.5 lb-in]
[.236-.0011 ] 36
[.394-.0014 ]
[1.417]

[.751-.0039 ]
19,1 -0,1

[1.378 -.0015 ]
+.0001]
[1.378 -.0079]

[1.26 +.0007
ø32 +0,002
+0,018

ø35 -0,039
35 -0,2

M20x1,5
[1.378]

[1.732]
ø35

ø44
ø4,5
M8
A [.177]
56,5±0,4
min 16 [.63] deep Taper 1:10 5
[2.224±.016] 58±0,4 [.196]
[2.283±.016]

CO - ø1¼" straight, Parallel key 5 16"x 5 16 "x 1¼"BS46 SH - ø1¼" splined 14T, DP12/24 ANS B92.1-1970
Max. Torque 77 daNm [6815 lb-in] Max. Torque 95 daNm [8400 lb-in]
7,96 -0,025
[.313 -.001 ] 36 +2
[1.417+.079]
[1.39 -.001 ]
35,33 -0,25

ø31,75-0,051

ø31,75-0,025

[1.25 -.001 ]
[1.25 -.002 ]
[1.378]

[1.378]
ø35

ø35
3/8-16UNC 47,5±0,4 M8
min 19 [.75] deep [1.87±.016] min 16 [.63] deep 56,5±0,4
[2.224±.016]

SL - ø34,85 p.t.o. DIN 9611 Form 1 SA - 7/8''-13T splined DP16/32 ANS B92.1-1970
Max. Torque 77 daNm [6815 lb-in] Max. Torque 20 daNm [1770 lb-in]
76±1
[2.992±.039]
A-A 38±0,25 ø18,6 -0,2
[1.496±.01] R4 R2,5
8,64 -0,11 [.732 -.0079 ]
7 [.16]
[.34-.0043 ] A .098
[.28]
30 0

[.866±.0039]
ø22±0,1
[1.157±.0039]

[1.378]
[1.372 -.0047]
ø34,85 -0,12
ø29,4±0,1

ø35
[1.378]
ø35

13±0,5
33±0,2 [.512±.0197]
R6,7
ø28,9 -0,15 [1.299±.0079]
A [.264]
[1.138 -.006 ] 100±0,4
[3.937±.016]

mm [in]
MAX. PERMISSIBLE SHAFT SEAL PRESSURE
Max. return pressure without drain line or
max. pressure in the drain line

1: Drawing for Standard Shaft Seal

1 2: Drawing for High Pressure Seal ("U" Seal)

- continuous operations
- intermittent operations

17
MS
MOTORS
DIMENSIONS AND MOUNTING DATA

MSB Motor with Drum Brake

53
Actuating the brake level, the brake MSBR [2.165]
shaft is turned. The rectangular shape
A B of the inner part of this shaft forces the
brake pads to be pressed against the
brake drum. This brakes the wheel or
the winch drum.

[2.756]
70
Releasing the level, the springs pull it and the brake pads back
to the initial position. The motor output shaft is released.
0
Minimum angle adjustment is 10 . It can be adjusted by
dismounting the level. Depending on the application You can

[2.756]
choose the actuating direction of the brake level. The rod

70
MSBL
connection actuating the brake should be capable of moving
at last 25 mm from neutral to extreme position. PL

MD PL
90
ø155±0,5
[6.102±.0196]
max ø199,5 [3.54]
max 122,5
[7.85]
[4.82]
ø101,6 -0,2 ø139,7±0,3
[4.0-.0078 ] [5.5±.0118]

5xM12x1,5
F
S=5
[.39]
10

[1.02]
26

max 120,5
[4.75]
[2.69]
68,3
[.169]
4,3

[.67]
17
ø10,3 4xM12
[.197±.0078]
max 47
[1.85]

[.406]
[.63]

[.69]
17,5

5±0,2
16

max 54
L1

[2.13]
[.39]
L2

103
10

[4.055]
max L

T
Port A Port Dim.
C See Page 16

Port B mm [in]

ø130 -0,075
P(A,B) [5.118 -.0029]

E Rear ports
Type L, mm[in] L1,mm[in.] L2,mm[in.] *LE, mm[in]
L2

MSB 80 119 [4.69] 14,0 [.55] 74 [2.91] 127 [5.00]

max LE

MSB100 122 [4.80] 17,4 [.69] 77 [3.03] 130 [5.12]

MSB 125 126 [4.96] 21,8 [.86] 82 [3.23] 134 [5.28]
MSB 160 132 [5.20] 27,8 [1.09] 88 [3.47] 140 [5.51]
MSB 200 139 [5.47] 34,8 [1.37] 95 [3.74] 147 [5.79]
Port A Port B MSB 250 148 [5.83] 43,5 [1.71] 110 [4.33] 156 [6.14]
C : 2xM10-12 mm [.47 in] depth MSB 315 159 [6.26] 54,8 [2.16] 115 [4.53] 167 [6.57]
F : Inspection hole for checking brake lining MSB 400 174 [6.85] 69,4 [2.73] 130 [5.12] 182 [7.17]
P(A,B) : 2xG1/2 or 2xM22x1,5-15 mm [.59 in] depth MSB 475 188 [7.40] 82,6 [3.25] 143 [5.63] 196 [7.72]
T : G ¼ or M14x1,5- 12 mm [.47 in] depth (plugged) MSB 525 180 [7.09] 74,5 [2.93] 135 [5.32] 188 [7.40]
Standard Rotation Reverse Rotation MSB 565 186 [7.32] 80,2 [3.16] 141 [5.55] 192 [7.56]
Viewed from Shaft End Viewed from Shaft End
Port A Pressurized - CW Port A Pressurized - CCW * -For Rear Ported Motors.
Port B Pressurized - CCW Port B Pressurized - CW
18
MS
MOTORS
PERMISSIBLE SHAFT LOADS

Mounting Flange:
Pr Pr -1 -.5 0 .5 1 1.5 2 2.5 3 in
lbs daN Standard
7000 -30 -20 -10 0 10 20 30 40 50 60 70 80 mm A-2
3000
Magneto
6000 500 daN
2500
1124 lbs.
5000
2000
4000
1
1500
3000
1000
2000

1000 500

0 0
0 10 20 30 40 50 60 70 80 90 100 110 120 mm W - Wheel
0 .5 1 1.5 2 2.5 3 3.5 4 4.5 in

-40 -30 -20 -10 0 10 20 30 40 50 60 70 mm

Q - Square
-2 -1 -.5 0 .5 1 1.5 2 2.5 in

Shaft: All type shafts except SA

FUNCTION DIAGRAM MSB

PL
daN lbs

150 340
140 320 PL - Brake Lever Load
300 MB - Brake Torque
130
280 MD - Brake Lever Torque
120
260
110
240
100 220 MD
90 200 lb-in daNm
80 180
70 160 1264 14
60 140 1106 12
120 948
50 10
100 790
40 8
80 632
30 60 6
474
20 316 4
40
10 20 158 2
0 0
0 1000 2000 3000 4000 5000 6000 lb-in MB

0 10 20 30 40 50 60 70 daNm

19
MS
MOTORS
DIMENSIONS AND MOUNTING DATA - MSS and MSV

S Short Mount V Very Short Mount

max 27,1 [1.067]
min 23,8 [.937]

ø100 -0,054
ø90 -0,04
[.236±.0078]

[3.937-.0021 ] -0,12
24 [3.543-.0016
-.0047]
6±0,2

max 45,6 [1.795]

[.945]

min 45 [1.772]
"O" Ring 100x3

max 25
[.984]
4xM10

[.905]
23
"O" Ring 85x2
[.63]
16

[.63±.0039]
16±0,1
L1

L1
L2

max 103

max L
[4.055]

max L
Port A C Port A
C
Port Dim.
Port B See Page 16 Port B
P(A,B) P(A,B)
ø125±0,15 4xø11
[4.921±.0059] [.433]
102
[4.016]
[1.18]

[1.457]
[1.457]

[2.165]
37
37

53
ø104±0,15
ø5 ø5 [.197]
[4.095±.0059]
[.197] Drain port
ø4
[.157] 24
[.945]
ø145
[5.708]

E Rear ports
mm [in]

C: 2xM10-12 mm [.47 in] depth

max LE

P(A,B): 2xG1/2 or 2xM22x1,5-15 mm [.59 in] depth

T: G ¼ or M14x1,5- 12 mm [.47 in] depth (plugged)
Standard Rotation Reverse Rotation
Viewed from Shaft End Viewed from Shaft End
Port A Pressurized - CW Port A Pressurized - CCW
Port A Port B
Port B Pressurized - CCW Port B Pressurized - CW

Type L,mm[in] L2,mm[in]] LE,mm[in] Type L,mm[in] L2,mm[in] LE,mm[in] L1,mm[in]

MSS 80 125 [4.92] 83 [3.27] 134 [5.28] MSV 80 91 [3.58] 47 [1.85] 97 [3.82] 14,0 [.55]
MSS 100 129 [5.08] 87 [3.43] 138 [5.43] MSV 100 94 [3.70] 50,5 [1.99] 100 [3.94] 17,4 [.69]
MSS 125 133 [5.24] 90 [3.54] 141 [5.55] MSV 125 99 [3.90] 55 [2.17] 105 [4.13] 21,8 [.86]
MSS 160 139 [5.47] 96 [3.78] 147 [5.79] MSV 160 105 [4.13] 61 [2.40] 111 [4.37] 27,8 [1.09]
MSS 200 146 [5.75] 103 [4.05] 154 [6.06] MSV 200 112 [4.41] 68 [2.78] 118 [4.64] 34,8 [1.37]
MSS 250 155 [6.10] 112 [4.41] 163 [6.42] MSV 250 120 [4.72] 76,5 [3.01] 126 [4.96] 43,5 [1.71]
MSS 315 166 [6.54] 123 [4.84] 174 [6.85] MSV 315 132 [5.20] 88 [3.46] 138 [5.43] 54,8 [2.16]
MSS 400 181 [7.13] 138 [5.43] 189 [7.44] MSV 400 146 [5.75] 103 [4.05] 153 [6.02] 69,4 [2.73]
MSS 475 194 [7.64] 152 [5.98] 203 [7.99] MSV 475 160 [6.30] 116 [4.57] 166 [6.54] 82,6 [3.25]
MSS 525 186 [7.32] 144 [5.67] 195 [7.68] MSV 525 152 [5.98] 108 [4.25] 158 [6.22] 74,5 [2.93]
MSS 565 192 [7.56] 150 [5.91] 201 [7.91] MSV 565 158 [6.22] 114 [4.49] 164 [6.46] 80,2 [3.16]
* -For Rear Ported Motors.
20
MS
MOTORS
DIMENSIONS AND MOUNTING DATA - MSU

U Ultra Short Mount

-0,04
ø75 -0,12
-.0016
[2.953 -.0047 ]

-.0035 ]
[1.772 +.0043
4xM10
"O" Ring 75x3

+1,1
45 -0,9

max 23
[.276]

[.276]
7
L1
L2

max L
Port A
C
Port B Port Dim.
See Page 16
P(A,B)

102
[4.016]

[1.012]
25,7

[2.165]
53

ø104±0,15
ø5 [.197]
[4.095±.0059]
Drain port

E Rear ports
max LE

Port A Port B

Standard Rotation Reverse Rotation

C: 2xM10-12 mm [.47 in] depth Viewed from Shaft End
Viewed from Shaft End
P(A,B): 2xG1/2 or 2xM22x1,5 Port A Pressurized - CCW
Port A Pressurized - CW
15 mm [.59 in] depth Port B Pressurized - CCW Port B Pressurized - CW

Type L,mm[in] L2,mm[in] *LE,mm[in] L1,mm[in]

MSU 80 105,5 [4.15] 63 [2.48] 111,5 [4.39] 14,0 [.55]
MSU 100 109 [4.29] 66,5 [2.62] 115 [4.53] 17,4 [.69]
MSU 125 113 [4.45] 71 [2.80] 119 [4.69] 21,8 [.86]
MSU 160 119 [4.69] 77 [3.03] 125 [4.92] 27,8 [1.09]
MSU 200 126 [4.96] 84 [3.31] 132 [5.20] 34,8 [1.37]
MSU 250 135 [5.32] 92,5 [3.64] 141 [5.55] 43,5 [1.71]
MSU 315 146 [5.75] 104 [4.09] 152 [5.98] 54,8 [2.16]
MSU 400 160 [6.30] 119 [4.69] 167 [6.58] 69,4 [2.73]
MSU 475 174 [6.85] 132 [5.20] 180 [7.09] 82,6 [3.25]
MSU 525 166 [6.54] 124 [4.88] 172 [6.77] 74,5 [2.93]
MSU 565 172 [6.77] 130 [5.12] 178 [7.01] 80,2 [3.16]

* -For Rear Ported Motors. mm [in]

21
MS
MOTORS
DIMENSIONS OF THE ATTACHED COMPONENT

For MSS
52±0,3
[2.047±.0118]
27+0,5
+0,2
[1.063+.019
+.0078] 8+0,4
[.315 +.0157 ]

H I T
0,1 K

F
G

0,25 K
min ø4

min ø40 [1.575]

[4.921±.0059
[.158]

[1.378±.0197]

[4.212±.0275]
[3.937+.0034 ]

ø125±0,15
ø100 +0,087

ø107±0,7
K
ø35±0,5

[1.575]
ø40
[1.142±.0197]
ø29±0,5

20±1
[.787±.039] K
J
External Spline
2,3±0,05
12 DP 12/24
[.091±.0019]
ANS B92.1-76

G: Internal drain channel

F: Oil circulation hole I : O- Ring 100x3 mm [3.94x.12 in]
H: Hardened stop plate K: Conical seal ring
J: 4xM10-16 mm [.63 in] depth, 90
0
T: Drain connection G1/4 or M14x1,5

For MSV

26±0,1 15 +0,5
[1.023±.0039] [.591+.0157]
H J G
F

1,5±0,4 A
[.059±.0157] K
min ø40 [1.575]

max ø52 [2.05]

[1.142±.0197]

[1.378±.0197]
min ø4 [.158]

[3.543 +.0019]

[4.094±.0059]
ø90 +0,05

ø104±0,15
ø35±0,5
ø29±0,5

0,25 K

External Spline
20 0

12 DP 12/24
ANS B92.1-76
I
1.8±0,2
[.071±.0078]
46±0,4
[1.811±.0157] 0,1 A
0,006

F: Oil circulation hole G: Internal drain channel

H: Hardened stop plate I: O- Ring 85x2 mm [3.346x.0787 in]
J: 4xM10-26 mm [1.024 in] depth, 900 K: Conical seal ring mm [in]

22
MS
MOTORS

DIMENSIONS OF THE ATTACHED COMPONENT(continued)

For MSU
46,2+0,3
0,006
[1.819+.0118 ]
min 15 7,5 +0,5
[.59] [.295 +.0197]
2,3±0,05
[.091±.0019]
0,13 A

0,25 A G

A
K
min ø40 [1.575]
[1.142±.0197]

[1.378±.0197]

+.0008 ]
[2.953+.0035

[3.26 +.0078 ]
ø29±0,5

ø35±0,5

+0,09
ø75 +0,02

ø82,8 +0,2

0,5±0,4
[.019±.0157]

External Spline
12 DP 12/24
I
ANS B92.1-76
J
19±0,1
[.748±.0039] J: 4xM10-26 mm [1.024 in] depth, 900, ø104 [4.094]
I: O- Ring 75x3 mm [2.952x.12 in]
G: Internal drain channel
K: Conical seal ring
mm [in]
DRAIN CONNECTION

The drain line has to be used when pressure in the return line can exceed the permissible pressure. It can be
connected:
- For MSS at the drain port of the motor;
- For MSV and MSU at the drain connection of the attached component. The maximum pressure in the drain line is
limited by the attached component and its shaft seal.
The drain line must be possible for oil to flow freely between motor and attached component and must be led to the
tank. The maximum pressure in the drain line is limited by the attached component and its seal.

INTERNAL SPLINE DATA FOR THE ATTACHED COMPONENT

Standard ANS B92.1-1976, class 5

[m=2.1166; corrected x.m=+0,8] Lo R

Fillet Root Side Fit mm inch

Number of Teeth z 12 12
Diametral Pitch DP 12/24 12/24 Dri
Pressure Angle 30º 30º Dri
Pitch Dia. D 25,4 1
28,0-0,1
D
Major Dia. Dri 1.1 ÷ 1.098 R
Minor Dia. Di 23,0 +0,033 .907 ÷ .905 d L
Space Width [Circular] Lo 4,308±0,020 .1704 ÷ .1688
Fillet Radius R 0,2 .008 Hardening Specification:
Max. Measurement L 17,62+0,15 .699 ÷ .694 HV=750±50 on the surface
between Pins HV=560 at 0,7±0,2 mm [.035÷.019 in] case depth
Pin Dia. d 4,835±0,001 .19039÷.19031 Material: 20 MoCr4 EN 10084 or better

23
MS
MOTORS

ORDER CODE

1 2 3 4 5 6 7 8

Pos.1 - Mounting Flange Pos.5 - Shaft Seal Version (see page 17)
omit - SAE A-4 mount, four holes omit - Low pressure seal
A - SAE A-2 mount, two holes U - High pressure seal
F - Magneto mount, four holes
Q - Square mount, four holes
B - Motor with drum brake Pos. 5 - Ports
S - Short mount omit - BSPP (ISO 228)
V - Very short mount M - Metric (ISO 262)
U - Ultra short mount Pos. 6 - Actuating Direction**
W - Wheel mount /R - Right
/L - Left
Pos.2 - Port type
omit - Side ports Pos. 7 - Special Features (see page 51)
E - Rear ports
Pos. 8 - Design Series
Pos.3 - Displacement code
omit - Factory specified
80 3 3
- 80,5 cm /rev [4.91 in /rev]
100 - 100,0 cm3/rev [6.10 in3/rev]
125 - 125,7 cm3/rev [7.67 in3/rev]
160 - 159,7 cm3/rev [9.74 in3/rev]
200 - 200,0 cm3/rev [12.20 in3/rev]
250 - 250,0 cm3/rev [15.30 in3/rev]
315 - 314,9 cm3/rev [19.20 in3/rev]
400 - 397,0 cm3/rev [24.20 in3/rev]
475 - 474,6 cm3/rev [28.96 in3/rev]
525 - 522,7 cm3/rev [31.88 in3/rev]
565 - 564,9 cm3/rev [34.47 in3/rev]

Pos.4 - Shaft Extensions*

omit - for B, S, U and V mounting flange
C - ø32 straight, Parallel key A10x8x45 DIN6885
CO - ø1¼" straight, Parallel key 5/16”x5/16”x1¼” BS46
K - ø35 tapered 1:10, Parallel key B6x6x20 DIN6885
SL - ø34,85 p.t.o. DIN 9611 Form 1
SH - ø1¼" splined 14T ANS B92.1-1970
SA - 7/8"-13T splined ANS B92.1-1970

NOTES:
* The permissible output torque for shafts must not be exceeded!
** Only for MSB

The hydraulic motors are mangano-phosphatized as standard.

24
HYDRAULIC MOTORS MT
APPLICATION
» Conveyors
» Metal working machines
» Agricultural machines
» Road building machines
» Mining machinery
» Food industries
» Special vehicles
» Plastic and rubber machinery etc.

CONTENTS OPTIONS
Specification data ......................................26÷27 » Model - Disc valve, roll-gerotor
Function diagrams .................................... 28÷31 » Flange with wheel mount
Dimensions and mounting .........................32÷33
» Short motor
Shaft extensions ............................................ 34
» Tacho connection
Permissible Shaft Seal pressure .................... 34
Dimensions and mounting- MTS, V ......... 35÷36 » Speed sensoring
Internal Spline data ....................................... 37 » Side and rear ports
Permissible shaft loads .................................. 37 » Shafts - straight, splined and tapered
Tacho connection .......................................... 38 » Metric and BSPP ports
Order code .................................................... 38
» Other special features

GENERAL
Max. Displacement, 3
cm /rev [in /rev]
3
724,3 [44.2]
Max. Speed, [RPM] 775
Max. Torque, daNm [lb-in] cont.: 130 [11500] int.: 148 [13100]
Max. Output, kW [HP] 40 [54]
Max. Pressure Drop, bar [PSI] cont.: 200 [2900] int. 240 [348 0]
Max. Oil Flow, lpm [GPM] 150 [39.6]
Min. Speed, [RPM] 5
Permissible Shaft Loads daN [lbs] Pa=1000 [2250]
Pressure fluid Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)
Temperature range,
O O
C [ F] -40÷140 [-40÷284]
Optimal Viscosity range, mm /s [SUS]
2
20 ÷ 75 [98 ÷ 347]
Filtration ISO code 20/16 (Min. recommended fluid filtration of 25 micron s)

Oil flow in drain line Pressure Losses

p p
bar PSI

Oil flow in 14 200

Pressure drop Viscosity drain line 12
2 150
bar [PSI] mm /s [ SUS] lpm [GPM ] 10
8
20 [ 98 ] 2,5 [.660 ] 100
6
140 [ 2030]
35 [ 164 ] 1,5 [.396 ] 4 50
2
20 [ 98 ] 5 [1.321 ] 0 0
210 [ 3045] 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 Q, GPM
35 [ 164 ] 3 [.793 ]
0 10 20 30 40 50 60 70 80 90 100 110 120 Q, lpm

25
MT
MOTORS

SPECIFICATION DATA

MT MT MT MT
Type
160 200 250 315
Displacement, 161,1 201,4
12.29 251,8
15.36 326,3
19.90
3 3
cm³/rev [in³/rev] in. /rev. [Cm. /rev.] [9.83] [12.29] [15.36] [19.90]
Max. Speed, Cont. 622 620 496 382
[RPM] Int.* 775 752 601 461
Max. Torque Cont. 47 [4160] 59 [5220] 73 [6460] 95 [8410]
daNm [lb-in] Int.* 56 [4960] 71 [6285] 88 [7790] 114 [10090]
Peak** 66 [5840] 82 [7260] 102 [9030] 133 [11770]
Max. Output Cont. 26,5 [36] 33,5 [45] 33,5 [45] 33,5 [45]
kW [HP] Int.* 32 [43] 40 [54] 40 [54] 40 [54]
Max. Pressure Drop Cont. 200[2900] 200 [2900] 200 [2900] 200 [2900]
bar [PSI] Int.* 240[3480] 240 [3480] 240 [3480] 240 [3480]
Peak** 280[4050] 280 [4050] 280 [4050] 280 [4050]
Max. Oil Flow Cont. 100 [26] 125 [33] 125 [33] 125 [33]
lpm [GPM] Int.* 125[33] 150 [39.6] 150 [39.6] 150 [39.6]
Max. Inlet Pressure Cont. 210[3050] 210 [3050] 210 [3050] 210 [3050]
bar [PSI] Int.* 250[3600] 250 [3600] 250 [3600] 250 [3600]
Peak** 300[4350] 300 [4350] 300 [4350] 300 [4350]
Max. Return Pressure Cont. 140[2030] 140 [2030] 140 [2030] 140 [2000]
with Drain Line Int.* 175[2540] 175 [2540] 175 [2540] 175 [2500]
bar [PSI] Peak** 210[3050] 210 [3050] 210 [3050] 210 [3000]
Max. Starting Pressure with
Unloaded Shaft, bar [PSI] 10 [150] 10 [150] 10 [150] 10 [150]
Min. Starting Torque At max. press. drop Cont. 34 [3010] 43 [3800] 53 [4690] 74 [6550]
daNm [lb-in] At max. press. drop Int.* 41 [3630] 52 [4600] 63 [5580] 89 [7880]
Min. Speed***, [RPM] 10 9 8 7
Weight, kg [lb] MT 20 [44.1] 21,5 [47.4] 21 [46.3] 22 [48.5]
For Rear Ports MTW 22 [48.5] 22,5 [49.6] 23 [50.7] 24 [52.9]
+0,450[ .992] MTS 15 [33.1] 15,5 [34.2] 16 [35.3] 17 [37.5]
MTV 11 [24.3] 11,5 [25.4] 12 [26.5] 13 [28.7]

1. Intermittent speed and intermittent pressure must not occur simultaneously.

26
MT
MOTORS

SPECIFICATION DATA (continued)

Type MT MT MT MT
400 500 630 725
Displacement, 410,9
25.06 523,6
31.95 631,2
38.52 724,3
44.2
3 3
cm³/rev [in³/rev] in. /rev. [Cm. /rev.] [25.06] [31.95] [38.52] [44.2]
Max. Speed, Cont. 304 238 197 172
[RPM] Int.* 368 289 234 209
Max. Torque Cont. 108 [9560] 122 [10800] 130 [11500] 127 [11240]
daNm [lb-in] Int.* 126 [11150] 137 [12125] 148 [13100] 147 [13010]
Peak** 144 [12745] 160 [14160] 176 [15580] 175 [15490]
Max. Output Cont. 30 [40] 26,5 [36] 24,3 [33] 20,2 [27]
kW [HP] Int.* 35 [47] 30 [40] 27,5 [37] 26,8 [36]
Max. Pressure Drop Cont. 180 [2610] 160 [2320] 140 [2010] 120 [1740]
bar [PSI] Int.* 210 [3050] 180 [2610] 160 [2320] 140 [2010]
Peak** 240 [3480] 210 [3050] 190 [2760] 165 [2395]
Max. Oil Flow Cont. 125 [33] 125 [33] 125 [33] 125 [33]
lpm [GPM] Int.* 150 [39.6] 150 [39.6] 150 [39.6] 150 [39.6]
Max. Inlet Pressure Cont. 210 [3050] 210 [3050] 210 [3600] 210 [3050]
bar [PSI] Int.* 250 [3600] 250 [3600] 250 [4350] 250 [3600]
Peak** 300 [4350] 300 [4350] 300 [2000] 300 [4350]
Max. Return Pressure Cont. 140 [2000] 140 [2000] 140 [2500] 140 [2000]
with Drain Line Int.* 175 [2500] 175 [2500] 175 [3000] 175 [2500]
bar [PSI] Peak** 210 [3000] 210 [3000] 210 [3000] 210 [3000]
Max. Starting Pressure with
Unloaded Shaft, bar [PSI] 10 [150] 10 [150] 10 [150] 10 [150]
Min. Starting Torque At max. press. drop Cont. 84 [7435] 95 [8410] 95 [8410] 95 [8410]
daNm [lb-in] At max. press. drop Int.* 97 [8585] 106 [9380] 110 [9740] 115 [10180]
Min. Speed***, [RPM] 6 5 5 5
Weight, kg [lb] MT 23 [50.7] 24 [52.9] 23,5 [51.8] 24,5 [54.0]
For Rear Ports MTW 25 [55.1] 26 [57.3] 25,5 [56.2] 26,5 [58.4]
+0,450[ .992] MTS 18 [39.7] 19 [41.9] 18,5 [40.8] 19,5 [43.0]
MTV 14 [30.9] 15 [33.1] 14,5 [32.0] 15,5 [34.2]

1. Intermittent speed and intermittent pressure must not occur simultaneously.

27
MT
MOTORS
FUNCTION DIAGRAMS
MT 160

Q=10 l/min
2.6 GPM

20 l/min
5.3 GPM

40 l/min
10.6 GPM

60 l/min
15.9 GPM

80 l/min
21 GPM

100 l/min
26 GPM

125 l/min
33 GPM
M M
lb-in daNm

5500
60
5000 p=240 bar
55 3480 PSI
35kW
4500
50
70%
int.

30kW
200 bar
4000 45
80% 2900 PSI

3500 40
25kW
160 bar
35 85% 2320 PSI
cont.

3000
t= 86%
20kW
30
2500
120 bar
25 1740 PSI
2000 15kW
20 10kW
1500 80 bar
15 5kW 1160 PSI
1000
10
40 bar
500 5 580 PSI

0 0
cont. int. n
-1
0 100 200 300 400 500 600 700 800 min (rpm)

MT 200
Q=10 l/min
2.6 GPM
20 l/min
5.3 GPM

40 l/min
10.6 GPM

60 l/min
15.9 GPM

80 l/min
21 GPM

100 l/min
26 GPM

125 l/min
33 GPM

150 l/min
39.6 GPM

M M
lb-in daNm
75
6500
70 p=240 bar
6000 35kW 3480 PSI
65
40kW
int.

5500
60 70%
5000 80% 200 bar
55 2900 PSI
30kW
4500 50 85%
cont.

4000 45 160 bar

25kW 2320 PSI
86%
3500 40
20kW

3000 35
120 bar
15kW 1740 PSI
30
2500
25 10kW
2000 80 bar
20
t= 87% 1160 PSI
1500
15 5kW
1000
10 40 bar
500 580 PSI
5

0 0
cont. int. n
-1
0 100 200 300 400 500 600 700 800 min (rpm)

M M

150 l/min
39.6 GPM
80 l/min
21 GPM

100 l/min
26 GPM

125 l/min
33 GPM
Q=10 l/min
2.6 GPM

5.3 GPM

40 l/min
10.6 GPM
20 l/min

60 l/min
15.9 GPM
lb-in daNm
8500 95
8000 90
p=240 bar
7500 85 3480 PSI
7000 80
40kW
int.

75
6500 70%
200 bar
70
6000 80% 35kW 2900 PSI
65
5500 25kW
60
5000 30kW 160 bar
cont.

55 20kW
2320 PSI
4500 50 85%
4000 15kW
45
120 bar
3500 40
1740 PSI
10kW
3000 35
30
2500
N=5kW 80 bar
25
2000 t= 87% 1160 PSI
20
1500
15
1000 10 40 bar
500 580 PSI
5
0 0
cont. int. n
0 50 100 150 200 250 300 350 400 450 500 550 600 min-1 (rpm)

MT 315
150 l/min
39.6 GPM
80 l/min
21 GPM

100 l/min
26 GPM

125 l/min
33 GPM
Q=10 l/min
2.6 GPM
20 l/min
5.3 GPM

40 l/min
10.6 GPM

60 l/min
15.9 GPM

M M
lb-in daNm
120
10000 p=240 bar
110
3480 PSI
9000 100 40kW
int.

70%
80% 200 bar
8000 90 2900 PSI
35kW
7000 80 25kW
30kW
85% 160 bar
cont.

70 20kW 2320 PSI

6000
87%
60 15kW
5000 120 bar
50 10kW 1740 PSI
4000
40
3000 N=5kW 80 bar
t= 88%
30 1160 PSI
2000
20

1000 40 bar
10
580 PSI
0 0
cont. int. n
-1
0 50 100 150 200 250 300 350 400 450 min (rpm)

80 l/min
21 GPM

125 l/min
33 GPM

150 l/min
39.6 GPM
100 l/min
26 GPM
Q=10 l/min
2.6 GPM

5.3 GPM

40 l/min
10.6 GPM
20 l/min

60 l/min
15.9 GPM
M M
lb-in daNm

130
11000 p=210 bar
120 3050 PSI
int.

70%
10000
110
180 bar
9000 100 2610 PSI
80%
8000 90 30kW 150 bar
cont.

85%
2175 PSI
7000 80
87% 25kW
70 120 bar
6000
20kW 1740 PSI
60
5000
50 90 bar
4000 15kW 1160 PSI
t= 88%
40
3000 10kW 60 bar
30 870 PSI
2000
20
5kW
N=2,5kW 30 bar
1000 10 435 PSI
70%
0 0
n
0 50 100 150 200 250 300 350 min-1 (rpm)

MT 500
80 l/min
21 GPM

150 l/min
39.6 GPM
100 l/min
26 GPM

125 l/min
33 GPM
Q=10 l/min
2.6 GPM
20 l/min
5.3 GPM

40 l/min
10.6 GPM

60 l/min
15.9 GPM

M M
lb-in daNm

150
13000
140
12000 p=180 bar
2610 PSI
int.

130
11000
120 160 bar
30kW 2320 PSI
10000
110
140 bar
9000 100 2030 PSI
25kW
cont.

20kW
8000 90 120 bar
15kW 1740 PSI
7000 80

6000 70
90 bar
60 5kW 10kW 87% 1160 PSI
5000 t= 90%
85%
50
4000 80% 60 bar
40 N=2,5kW 870 PSI
3000
30
2000
20 30 bar
1000 435 PSI
10
0 0
cont. int. n
-1
0 25 50 75 100 125 150 175 200 225 250 275 300 min (rpm)

MT 630

M M

80 l/min
21 GPM

100 l/min
26 GPM

125 l/min
33 GPM

150 l/min
39.6 GPM
Q=10 l/min
2.6 GPM
20 l/min
5.3 GPM

40 l/min
10.6 GPM

60 l/min
15.9 GPM
lb-in daNm
14000 160
150
13000
140
12000 p=160 bar
int.

130 25kW
11000 2320 PSI
120
10000 140 bar
110 20kW 2030 PSI
9000 100
cont.

8000 90 120 bar

15kW 1740 PSI
7000 80
80% 75%
6000 70
85% 90 bar
60 1160 PSI
5000
t= 87% 10kW
50
4000
40 60 bar
3000 870 PSI
30 5kW
2000 20 30 bar
2,5kW
1000 10 435 PSI

0 0
cont. int. n
-1
0 25 50 75 100 125 150 175 200 225 250 min (rpm)

MT 725
80 l/min
21 GPM

100 l/min
26 GPM

125 l/min
33 GPM

150 l/min
39.6 GPM
Q=10 l/min
2.6 GPM
20 l/min
5.3 GPM

40 l/min
10.6 GPM

60 l/min
15.9 GPM

M M
lb-in daNm
14000 160
150
13000
140
12000
130
int.

20kW p=140 bar

11000 2030 PSI
120
10000 120 bar
110
1740 PSI
9000 100
15kW
cont.

8000 90

7000 80 90 bar
1160 PSI
6000 70 10kW 73%
77%
60
5000 75%
50 t= 82% 80% 60 bar
4000 870 PSI
40
3000 5kW
30
2000 30 bar
20 435 PSI
N=2,5kW
1000 10
0 0
cont. int. n
-1
0 25 50 75 100 125 150 175 200 225 min (rpm)

DIMENSIONS AND MOUNTING DATA

SL Shaft SL Shaft
C, CO Shaft
Shaft Dim. K Shaft C, CO Shaft
K Shaft See Page 34
SH Shaft SH Shaft
max 134
[5.276]
max 114

max 114
[4.488]

[4.488]

max 202
[7.953]
max 182

max 182
[7.165]

[7.165]
[2.36]
60

T Flange Dim.
L2

See Page 33
max L

75
75
T

L1
max
125125
L1

[2.953]
[2.953]
[4.621]
[4.921] max 125
125

max L
[4.921]
[4.621]

L2
C
Port A
Port B

Port Dim.
See Page 33 72
P(A,B) [2.835]

E Rear ports
mm [in]

C: 4xM10-10 mm [.39 in] depth

max LE

P(A,B): 2xG3/4 or 2xM27x2-17 mm [.67 in] depth

T: G 1/4 or M14x1,5 - 12 mm [.47 in] depth (plugged)
Standard Rotation Reverse Rotation
Viewed from Shaft End Viewed from Shaft End
Port A Pressurized - CW Port A Pressurized - CCW
Port A Port B Port B Pressurized - CCW Port B Pressurized - CW

Type L,mm [in] L2, mm [in] **LE, mm [in] Type L, mm [in] L2, mm [in] **LE,mm [in] *L1, mm [in]
MT 160 190 [7.48] 140 [5.51] 200 [7.87] MTW 160 123 [4.84] 73 [2.87] 133 [5.23] 16,5 [.65]
MT 200 195 [7.68] 145 [5.71] 205 [8.07] MTW 200 128 [5.04] 78 [3.07] 138 [5.43] 21,5 [.85]
MT 250 201 [7.91] 151 [5.95] 211 [8.31] MTW 250 134 [5.28] 84 [3.31] 144 [5.67] 27,8 [1.09]
MT 315 211 [8.31] 161 [6.34] 221 [8.70] MTW 315 144 [5.67] 94 [3.70] 154 [6.02] 37,0 [1.46]
MT 400 221 [8.70] 171 [6.73] 231 [9.09] MTW 400 154 [6.06] 104 [4.09] 164 [6.45] 47,5 [1.87]
MT 500 235 [9.25] 185 [7.28] 245 [9.64] MTW 500 168 [6.61] 118 [4.65] 178 [6.61] 61,5 [2.42]
MT 630 231 [9.09] 181 [7.13] 241 [9.49] MTW 630 164 [6.46] 114 [4.49] 174 [6.85] 57,5 [2.26]
MT 725 240 [9.45] 190 [7.48] 250 [9.84] MTW 725 173 [6.81] 123 [4.84] 183 [7.21] 66,5 [2.62]

* - The width of the roll-gerotor is 3,5 mm [.138 in] greater than L1.
** - For Rear Ported Motors.

32
MT
MOTORS
MOUNTING

Square Mount (4 Holes)

60
4xø14±0,1 ø160±0,4 [2.36]
18 8
[.551±.0039] [6.299±.0157] [.709] [.315]

[4.921 -.0025 ]
[2.835±.039]
ø125 -0,063
max 143

ø72±1
[5.63]

max 143
[5.63]
W Wheel Mount
4 18
4xø18±0,15 ø200±0,4 [.157] [.709]
[.708±.0059] [7.874±.0157] 78,2
[3.079]
20
[.787]

[4.921 -.0039 ]
[6.772 -.0025 ]

[6.299 -.0025 ]
ø172 -0,063

ø160 -0,063
[2.835±.039]
ø125 -0,1
max 180
[7.087]

ø72±1
[2.953]
75

7
max 180 [.276] max 99
[7.087] [3.897]

PORTS

Port A Side Ports E Rear Ports

23±0,6
[.905±.024] 72 7
72
12,5±0,5 12,5±0,5
[2.835] Port A [2.835] [.276]
[.85±.019]
21,6±0,5

C [.492±.019] [.492±.019]
[1.732±.0118] [1.732±.0118]
[.787±.0118]
[.85±.019]

44±0,3
20±0,3
21,6±0,5

[.787±.0118]

[.85±.019]
21,6±0,5

44±0,3
20±0,3
[.85±.019]
21,6±0,5

P(A,B)
12,5±0,5 12,5±0,5 Port B
[.492±.019] [.492±.019]

Port B
mm [in]
Standard Rotation Reverse Rotation
Viewed from Shaft End Viewed from Shaft End C: 4xM10-10 mm [.39 in] depth
Port A Pressurized - CW Port A Pressurized - CCW P(A,B): 2xG3/4 or 2xM27x2-17 mm [.67 in] depth
Port B Pressurized - CCW Port B Pressurized - CW T: G 1/4 or M14x1,5 - 12 mm [.47 in] depth (plugged)

33
MT
MOTORS
SHAFT EXTENSIONS

C -ø40 straight, Parallel key A12x8x70 DIN 6885 K -tapered 1:10, Parallel key B12x8x28 DIN 6885
Max. Torque 132,8 daNm [11755 lb-in] Max. Torque 210,7 daNm [18650 lb-in]
S=46
Tightening torque
A-A 12 -0.043
50±3 daNm
12 -0.043 [4425±265 lb-in]
0 [.472-.0017 ] A
[.472-.0017 ] 45

[.248]
ø6,3
[1.692 -.0079]

+.0001 ]
[1.575+.0007
ø40 +0,002
+0,018

[2.205]
M30x2
43 -0,2

[1.771]

ø56
ø45

ø45
[.95 -.0079]
24,15 -0,2
M12 A 9
82 -0,2
min 25 [.984] deep Taper 1:10 [.354]
[3.228-.0079]
54±0,4 4
[2.126±.016] [.157]
82±0,2
[3.228±.0079]

CO-ø1½" straight, Parallel key 3 8"x 3 8"x 2¼" BS46 SH -ø1½" splined 17T, DP 12/24 ANSI B92.1-1976
Max. Torque 132,8 daNm [11755 lb-in] Max. Torque 132,8 daNm [11755 lb-in]
9.545 -0,02
56 +2
[.379-.0008]
[2.205 +.079 ]
[1.669-.0079 ]

ø38,1 -0,025

[1.5 -.001 ]
ø38,1 -0,05
42,4 -0,2

[1.5 -.0019]

[1.771]
[1.771]

ø45
ø45

82 -0,2 82-0,2
3/8-16 UNC [3.228-.0079] M12
[3.228-.0079]
min 25 [.984] deep min 25 [.984] deep

SL -ø34,85 p.t.o. DIN 9611 Form 1

Max. Torque 77 daNm [6815 lb-in]
102 -0,2
[4.016-.0079]
76±1
[2.992±.039]
[1.157±.0039]

[1.372 -.0047]
ø34,85 -0,12
ø29,4±0,1

38±0,25
[1.496±.01]
8,64 -0,11 A-A
[.34-.0043 ] ø28,9 -0,15 A
[1.138 -.006 ]
[1.771]
ø45

7
A [.28]
R6,7 mm [in]
[.264]

MAX. PERMISSIBLE SHAFT SEAL PRESSURE for MT motors

Max. return pressure without drain line or
P P
max. pressure in the drain line
PSI bar
1800
120
1600
1450 100
1400
1200 80 1: Drawing for Standard Shaft Seal
1090 75
1000 2: Drawing for High Pressure Seal ("U" Seal)
60
800

600 40 2
400
- continuous operations
200
20
1
- intermittent operations

0 0
0 100 200 300 400 500 600 700 800 min-1

34
MT
MOTORS
DIMENSIONS AND MOUNTING DATA - MTS and MTV

S Short Mount V Very Short Mount

max 36,1 [1.421]

min 32,9 [1.295]
-0,04
ø106-0,12
ø125 -0,063
[4.921-.0025 ] [4.173 -.0016
-.0047 ]
28
[1.102] ø105,5±0,1
[4.153±.0039]
[.315]

"O" Ring 125x3

[2.657-.075 ]
8

67,5 -1,9
4xM14

[.276]
[1.22]

7
31
"O" Ring 100x3
[.708]

max 25
[.984]
18

T
L2

[.905±.0039]
max 125
L1

23±0,1
L1
max 125
[4.921]
[4.921]

max L

max L
C
Port A Port A
Port B Port B

P(A,B)
4xø14,2
[.552] ø160±0,4 Port Dim.
ø6 [6.299±.0157]
See Page 33
[.236] ø125
ø6 [.236] [4.921]
Drain port
[1.693]

[1.693]
43
43

max 125
[4.921]
[1.969]
50
[2.835]

[2.835]
72

ø6
[.236]

28
[1.102]
ø186
[7.323]

mm [in]
E Rear ports

C: 4xM10-10 mm [.39 in] depth

P(A,B): 2xG3/4 or 2xM27x2-17 mm [.67 in] depth
T: G 1/4 or M14x1,5 - 12 mm [.47 in] depth (plugged)
E
max L

Standard Rotation Reverse Rotation

Viewed from Shaft End Viewed from Shaft End
Port A Pressurized - CW Port A Pressurized - CCW
Port A
Port B Pressurized - CCW Port B Pressurized - CW
Port B

Type L, in.[mm] **LE,mm[ in.] Type L, in.[mm] *L1,mm [in]

MTS 160 146 [5.75] 96 [3.78] 156 [6.14] MTV 160 101 [3.98] 51,5 [2.02] 111 [4.37] 16,5 [ .65]
MTS 200 151 [5.95] 101 [3.98] 161 [6.33] MTV 200 106 [4.17] 56,5 [2.22] 116 [4.57] 21,5 [ .85]
MTS 250 157 [6.18] 107 [4.21] 167 [6.57] MTV 250 112 [4.41] 62,8 [2.47] 122 [4.80] 27,8 [1.09]
MTS 315 166 [6.53] 116 [4.56] 176 [6.93] MTV 315 121 [4.76] 72,0 [2.83] 131 [5.16] 37,0 [1.46]
MTS 400 177 [6.97] 127 [5.00] 187 [7.36] MTV 400 132 [5.19] 82,5 [3.25] 142 [5.59] 47,5 [1.87]
MTS 500 191 [7.52] 142 [5.59] 201 [7.91] MTV 500 146 [5.75] 96,5 [3.80] 156 [6.14] 61,5 [2.42]
MTS 630 187 [7.36] 138 [5.43] 197 [7.76] MTV 630 142 [5.59] 92,5 [3.64] 152 [5.98] 57,5 [2.26]
MTS 725 196 [7.72] 147 [5.79] 206 [8.11] MTV 725 151 [5.95] 101,5[4.00] 161 [6.34] 66,5 [2.62]
* - The width of the roll-gerotor is 3,5 mm [.138 in] greater than L1.
** - For Rear Ported Motors.
35
MT
MOTORS
DIMENSIONS OF THE ATTACHED COMPONENT

MTS
External Spline
46±0,3 16 DP 12/24
[1.811±.0118] 11,2±0,2 ANS B92.1-76
Internal spline
16 DP 12/24
[.441±.0079] T
ANS B 92.1-1976 I

2,3±0,05 K
[.091±.002]
5
[.197]

[1.535±.0197]

[1,988±.0197]
[.236]

ø125 +0,063
[4.921 +.0025]
min ø6

[5.228±.0079]

[2.125 +.0157 ]
[6.299±.0157]
ø50,5±0,5

[2.48+.019 ]
ø132,8±0,2

[3.62 +.039]
ø39±0,5

ø160±0,4

ø63 +0,5
min ø55

ø54 +0,4
[2,165]

ø92 +1
G
J
26±1 29+1
[1.024±.039] 69±0,4 [1.142+.039 ]
34,5±0,2
[2.717±.0157]
[1.358±.0079]

I : O- Ring 125x3 mm [4.921x.118 in]

F: Oil circulation hole
J: 4xM12-18 mm [.71 in] depth, 90
0

G: Internal drain channel

K: Conical seal ring
H: Hardened stop plate
T: Drain connection G1/4 or M14x1,5 mm [in]
MTV
26±1 22,5 -0,5
[1.024±.039] [.885 -.0197]

Internal spline
16 DP 12/24
ANS B 92.1-1976 External Spline
16 DP 12/24
1,8±0,2 ANS B92.1-76
M
1,5±0,4[.071±.0078] K
[.059±.0157]
[.236]

[1.535±.0197]

+.0008]
[2.008±.0197]
min ø6

[4.921±.0079]
[4.173 +.0024
ø106 +0,06
+0,02
ø51±0,5

min ø55
[2,165]

ø125±0,2
ø39±0,5

R0,5
[.0197] 1,6
20 0

G
F I
4xM14-26 depth min
H 0
H: Hardened stop plate
67,5 +1,8
+0,6 Four 90
[2.657 +.071
+.024 ] I : O- Ring 100x3 mm [3.94x.12 in]
F: Oil circulation hole K: Conical seal ring
G: Internal drain channel

DRAIN CONNECTION
The drain line has to be used when pressure in the return line can exceed the permissible pressure. It can be
connected:
- For MTS at the drain port of the motor;
- For MTV at the drain connection of the attached component. The maximum pressure in the drain line is limited by
the attached component and its shaft seal.
The drain line must be possible for oil to flow freely between motor and attached component and must be led to the
tank. The maximum pressure in the drain line is limited by the attached component and its seal.

36
MT
MOTORS

INTERNAL SPLINE DATA FOR THE ATTACHED COMPONENT

Standard ANS B92.1-1976, class 5
[m=2.1166; corrected x.m=1]

Fillet Root Side Fit mm inch

Number of Teeth z 16 16
Diametral Pitch DP 12/24 12/24
Pressure Angle 30° 30°
Pitch Dia. D 33,8656 1.3333
+0,4
Major Dia. Dri 38,4 1.5118±1.5275
+0,04
Minor Dia. Di 32,15 1.2657±1.2673
Space Width [Circular] Lo 4,516±0,037 .1763±.1791
Fillet Radius R 0,5 .02
+0,10
Max. Measurement L 26,9 1.063±1.059 Hardening Specification:
between Pins HV=750±50 on the surface.
d HV=560 at 0,7±0,2 mm [.035±.019in] case depth
Pin Dia. 4,835±0,001 .19026±.19034 Material: 20 MoCr4 EN 10084 or SAE8620.

PERMISSIBLE SHAFT LOADS

Curve " 1 " shows max. radial shaft load. Any shaft load exceeding the values shown by the curve will seriously
reduce motor life.

Mounting Flange:
Pr Pr
0 .5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 in
lbs daN
14000 0 20 40 60 80 100 120 140 160 180 mm W - Wheel
6000

12000
5000 1000 daN
2250 lbs.
10000
4000
8000

3000
6000

2000
4000

2000 1000

0 0
-80 -60 -40 -20 0 20 40 60 80 100 120 mm
Standard
-3 -2.5 -2 -1.5 -1 -.5 0 .5 1 1.5 2 2.5 3 3.5 4 4.5 in

mm [in]

37
MT
MOTORS

MOTORS WITH TACHO CONNECTION

33 max L 72
[2.835]
[1.299]

ø3
[.118]
[1.89]
ø48

5
[.197]
[.315]
ø8

20 16
[.787] [.63] ø34 4xM5
[1.339] 8 [.315] deep

mm [in]

ORDER CODE

1 2 3 4 5 6 7 8

Pos.1 - Mounting Flange Pos.4 - Shaft Extensions*

omit - Square mount, four holes
omit - for S and V mounting flange
S - Short mount
C - ø40 straight, Parallel key A12x8x70 DIN6885
V - Very short mount
CO - ø1½ ” straight, Parallel key /8”x /8”x2¼” BS46
3 3

W - Wheel mount
K - ø45 tapered 1:10, Parallel key B12x8x28 DIN6885
Pos.2 - Port type SL - ø34,85 p.t.o. DIN 9611 Form 1
omit - Side ports SH - ø1½" splined 17T ANS B92.1-1976
E - Rear ports
Pos.5 - Shaft Seal Version (see page 34)
Pos.3 - Displacement code omit - Low pressure seal
160
3 3
- 61,6 cm /rev [9.83 in /rev] U - High pressure seal
200 - 201,4 cm3/rev [12.29 in3/rev] Pos.6 - Ports
250 - 251,8 cm3/rev [15.36 in3/rev] omit - BSPP (ISO 228)
315 - 326,3 cm3/rev [19.90 in3/rev]
M - Metric (ISO 262)
400 - 410,9 cm3/rev [25.06 in3/rev]
500 - 523,6 cm3/rev [31.95 in3/rev] Pos.7 - Special Features (see page 51)
630 - 631,2 cm3/rev [38.52 in3/rev] Pos.8 - Design Series
725 - 724,3 cm3/rev [44.20 in3/rev] omit - Factory specified

NOTES:
* The permissible output torque for shafts must not be exceeded!

The hydraulic motors are mangano-phosphatized as standard.

38
HYDRAULIC MOTORS MV
APPLICATION
» Conveyors
» Metal working machines
» Agricultural machines
» Road building machines
» Mining machinery
» Food industries
» Special vehicles
» Plastic and rubber machinery etc.

CONTENTS OPTIONS
Specification data ............................................ 39 » Model - Disc valve, roll-gerotor
Function diagrams ..................................... 41÷43 » Flange and wheel mount
Permissible shaft loads ................................... 43
» Short motor
Dimensions and mounting ......................... 44÷46
Dimensions and mounting - MVS .................... 47 » Tacho connection
Dimensions and mounting - MVV .................... 48 » Speed sensoring
Internal Spline data ......................................... 49 » Side ports
Tacho connection............................................. 49 » Shafts - straight, splined and tapered
Shaft extensions .............................................. 50 » BSPP ports
Order code ...................................................... 50
» Other special features

GENERAL
Max. Displacement,
3 3
cm /rev [in /rev] 801,8 [48.91]
Max. Speed, [RPM] 630
Max. Torque, daNm [lb-in] cont.: 188 [16650] int.: 211 [18650]
Max. Output, kW [HP] 64 [85,8]
Max. Pressure Drop, bar [PSI] cont.: 200 [2900] int.: 240 [3480]
Max. Oil Flow, lpm [GPM] 240 [63.4]
Min. Speed, [RPM] 5
Permissible Shaft Loads daN [lbs] Pa=1500 [3300]
Pressure fluid Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)
Temperature range,
O O
C [ F] -40÷140 [-40÷284]
Optimal Viscosity range, mm /s [SUS] 20÷75 [98÷347]
2

Filtration ISO code 20/16 (Min. recommended fluid filtration of 25 microns)

Oil flow in drain line Pressure Losses

250
16
Pressure drop Viscosity Oil flow in 14 200
drain line
bar [PSI] mm 2/s [ SUS] lpm [GPM ] 12
10 150
20 [98] 3 [.793] 8
140 [2030] 100
35 [164] 2 [ .528 ] 6
4 50
20 [98] 6 [ 1.585 ] 2
210 [ 3045]
35 [164] 4 [1.057] 0 0
0 5 10 15 20 25 30 35 40 45 50 55 Q, GPM

0 20 40 60 80 100 120 140 160 180 200 Q, lpm

39
MLHV
MV
MOTORS

SPECIFICATION DATA

MV MV MV MV MV
Type
315 400 500 630 800
Displacement, 314,5 400,9 499,6 629,1 801,8
3 3
cm /rev [In /rev] [19.18] [24.45] [30.48] [38.38] [48.91]
Max. Speed, Cont. 510 500 400 320 250
[RPM] Int.* 630 600 480 380 300
Max. Torque Cont. 92 [8150] 118 [10450] 146 [12950] 166 [14700] 188 [16650]
daNm [lb-in] Int.* 111 [9800] 141 [12500] 176 [15550] 194 [17150] 211 [18650]
Peak** 129 [11400] 164 [14500] 205 [18150] 221 [19550] 247 [21850]
Max. Output Cont. 42,5 [57] 53,5 [71.7] 53,5 [71.7] 48 [64.4] 42,5 [57]
kW [HP] Int.* 51 [68.4] 64 [85.8] 64 [85.8] 56 [75] 48 [64.4]
Max. Pressure Drop Cont. 200 [2900] 200 [2900] 200 [2900] 180 [2610] 160 [2320]
bar [PSI] Int.* 240 [3480] 240 [3480] 240 [3480] 210 [3050] 180 [2610]
Peak** 280 [4060] 280 [4060] 280 [4060] 240 [3480] 210 [3050]
Max. Oil Flow Cont. 160 [42.3] 200 [52.8] 200 [52.8] 200 [52.8] 200 [52.8]
lpm [GPM] Int.* 200 [52.8] 240 [63.4] 240 [63.4] 240 [63.4 240 [63.4]
Max. Inlet Pressure Cont. 210 [3050] 210 [3050] 210 [3050] 210 [3050] 210 [3050]
bar [PSI] Int.* 250 [3620] 250 [3620] 250 [3620] 250 [3620] 250 [3620]
Peak** 300 [4350] 300 [4350] 300 [4350] 300 [4350] 300 [4350]
Max. Return Pressure Cont. 140 [2040] 140 [2040] 140 [2040] 140 [2040] 140 [2040]
with Drain Line Int.* 175 [2540] 175 [2540] 175 [2540] 175 [2540] 175 [2540]
bar [PSI] Peak** 210 [3050] 210 [3050] 210 [3050] 210 [3050] 210 [3050]
Max. Starting Pressure with
Unloaded Shaft, bar [PSI] 8 [120] 8 [120] 8 [120] 8 [120] 8 [120]
Min. Starting Torque At max. press. drop Cont. 71 [6300] 91 [8100] 113 [10000] 133 [11800] 151 [13400]
daNm [lb-in] At max. press. drop Int.* 85 [7500] 109 [9600] 136 [12000] 155 [13700] 170 [15000]
Min. Speed***, [RPM] 10 9 8 6 5
Weight, kg [lb] MV 31,8 [70.1] 32,6 [71.9] 33,5 [73.8] 34,9 [76.9] 36,5 [80.5]
MVW 32,4 [71.4] 33,2 [73.2] 34,1 [75.2] 35,5 [78.3] 37,1 [81.8]
MVS 22,7 [50] 23,5 [51.8] 24,4 [53.8] 25,6 [56.4] 27,7 [61.1]

1. Intermittent speed and intermittent pressure must not occur simultaneously.

40
MV
MOTORS

FUNCTION DIAGRAMS

MV 315
2.6 GPM

6.6 GPM

13.2 GPM

19.8 GPM

26.4 GPM

33 GPM

39.6 GPM

42.3 GPM

52.8 GPM
Q=10 l/min

25 l/min

50 l/min

75 l/min

100 l/min

125 l/min

150 l/min

160 l/min

200 l/min
M M
lb-in daNm

11000
120
10000
p=240 bar
9000 3480 PSI
100
40 kW
int.

8000 50 kW
30 kW 200 bar
2900 PSI
7000 80
175 bar
2540 PSI
cont.

20 kW
6000
60 140 bar
5000 2030 PSI
10 kW
4000 105 bar
40 N=5 kW 1520 PSI
3000 85%
70 bar
2000 1020 PSI
20 80%
1000 70% 35 bar
510 PSI
0 0
cont. int.
n
0 50 100 150 200 250 300 350 400 450 500 550 600 650 min-1 (rpm)

MV 400
M M
2.6 GPM

6.6 GPM

13.2 GPM

19.8 GPM

26.4 GPM

33 GPM

39.6 GPM

46.2 GPM

52.8 GPM

63.4 GPM
Q=10 l/min

25 l/min

50 l/min

75 l/min

100 l/min

125 l/min

150 l/min

175 l/min

200 l/min

240 l/min
lb-in daNm

15000
160
14000
13000
140
p=240 bar
12000
3480 PSI
11000
int.

120
10000 200 bar
50 kW 2900 PSI
9000 100
175 bar
cont.

8000 2540 PSI

40 kW
80
7000 140 bar
2030 PSI
6000 30 kW
60
5000 87% 105 bar
20 kW 1520 PSI
4000 85%
40
3000 70 bar
N=5 kW 80% 10 kW 1020 PSI
2000 20
1000 70% 35 bar
510 PSI
0 0
cont. int. n
-1
0 50 100 150 200 250 300 350 400 450 500 550 600 min (rpm)

FUNCTION DIAGRAMS

MV 500 2.6 GPM

6.6 GPM

19.8 GPM

26.4 GPM

33 GPM

39.6 GPM

175 l/min
46 GPM

52.8 GPM

63.4 GPM
13.2 GPM
Q=10 l/min

25 l/min

75 l/min

100 l/min

125 l/min

150 l/min

200 l/min

240 l/min
50 l/min
M M
lb-in daNm

16000 180
15000 p=240 bar
160 50 kW 3480 PSI
14000
int.

40 kW
13000 60 kW
140 30 kW 200 bar
12000
2900 PSI
11000 120 175 bar
cont.

10000 20 kW 2540 PSI

9000 100
140 bar
8000 10 kW 2030 PSI
7000 80
6000 105 bar
60 N=5 kW 1520 PSI
5000
4000 70 bar
40
3000 85% 1020 PSI
87%
2000 20 80% 35 bar
1000 70%
510 PSI
0 0
cont. int. n
-1
0 50 100 150 200 250 300 350 400 450 500 min (rpm)

MV 630
M M
2.6 GPM

6.6 GPM

19.8 GPM

26.4 GPM

33 GPM

39.6 GPM

52.8 GPM
13.2 GPM
Q=10 l/min

25 l/min

75 l/min

100 l/min

125 l/min

150 l/min

175 l/min
46 GPM

200 l/min
50 l/min

63.4 GPM
240 l/min

lb-in daNm

18000 200
17000 p=240 bar
3480 PSI
int.

16000 175 60 kW
15000
40 kW 180 bar
14000 50 kW 2610 PSI
150 30 kW
13000
12000 150 bar
cont.

11000 125 2175 PSI

20 kW
10000
9000 100 120 bar
1740 PSI
8000
7000 75 10 kW 90 bar
6000 1305 PSI
N=5 kW
5000
50
4000 87% 60 bar
85% 80% 870 PSI
3000 70%
2000 25
30 bar
1000 435 PSI
0 0
cont. int.
n
0 50 100 150 200 250 300 350 400 min-1 (rpm)

6.6 GPM
25 l/min

13.2 GPM

26.4 GPM

33 GPM

39.6 GPM

52.8 GPM

63.4 GPM
2.6 GPM

50 l/min

100 l/min

125 l/min

150 l/min

175 l/min
46 GPM

200 l/min

240 l/min
Q=10 l/min

19.8 GPM
75 l/min
M M
lb-in daNm
20000 225
19000
18000
int.

200 p=180 bar

17000 2610 PSI
16000
175 160 bar
15000 2320 PSI
14000
150 40 kW
13000
cont.

12000 20 kW 130 bar

30 kW 1885 PSI
11000 125
10000
9000 100 100 bar
10 kW 1450 PSI
8000
7000 75 N=5 kW 75 bar
6000
1090 PSI
5000
4000 50
80% 50 bar
85%
3000 720 PSI
2000 25
70% 25 bar
1000
360 PSI
0 0
cont. int. n
0 50 100 150 200 250 300 min-1 (rpm)
The function diagrams data is for average performance of randomly selected motors at back pressure
o
5÷10 bar [72.5÷145 PSI] and oil with viscosity of 32 mm²/s [150 SUS] at 50°C [122 F].

PERMISSIBLE SHAFT LOADS

The output shaft runs in tapered bearings that permit high axial and radial forces. The permissible radial load on
the shaft is shown for an axial load of 0 N as function of the distance from the mounting flange to the point of load
application. The curves apply to a B10 bearing life of 2000 hours at 100 RPM .
Curve " 1 " shows max. radial shaft load. Any shaft load exceeding the values shown by the curve will seriously
reduce motor life.
Mounting Flange:
-2.5 -2 -1.5 -1 -.5 0 .5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 in
Pr Pr
lbs daN -60 -40 -20 0 20 40 60 80 100 120 140 mm Standard
10000
22000
20000 9000
1500 daN
18000 8000 3370 lbs.

16000 7000
14000
6000
12000
5000
10000
4000
8000 1
3000
6000
2000
4000

2000 1000

0 0
0 20 40 60 80 100 120 140 160 180 200 mm W - Wheel
0 .5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 in

-80 -60 -40 -20 0 20 40 60 80 100 110 mm

SAE C
-3.5 -3 -2.5 -2 -1.5 -1 -.5 0 .5 1 1.5 2 2.5 3 3.5 4 4.5 in

43
MV
MOTORS

DIMENSIONS AND MOUNTING DATA - MV and MVC

K Shaft Shaft Dim. K Shaft

See Page 50
SH Shaft SH Shaft
C Shaft CO Shaft C Shaft CO Shaft

105 [4.134]
105 [4.134]

82 [3.228]
82 [3.228]
82 [3.228]
82 [3.228]

[.551+.0078 ]
14 +0,2
40 [1.575]

85 [3.346]
60 [2.362]

Flange Dim.
See Page 46

T T
L2
L2

max L
max L
L1

L1
max 145 [5.709] max 145 [5.709]

C C
Port A Port A
Port B Port B

P(A,B) Port Dim. P(A,B)

See Page 46

C: 4xM12 - 12 mm [.47 in] depth

P(A,B): 2xG1 - 20 mm [.79 in] depth
T: G 1/4 - 12 mm [.47 in] depth

Standard Rotation Reverse Rotation

Viewed from Shaft End Viewed from Shaft End
Port A Pressurized - CW Port A Pressurized - CCW
Port B Pressurized - CCW
mm [in]
Port B Pressurized - CW

Type L, mm [in] L2, mm [in] Type L, mm [in] L2, mm [in] *L1, mm [in]
MV 315 214,5 [8.45] 160[6.30] MVC 315 238,25 [9.38] 184,26 [7.25] 22,0 [ .87]
MV 400 221,5 [8.72] 167[6.58] MVC 400 245,25 [9.66] 191,26 [7.53] 29,0 [1.14]
MV 500 229,5 [9.04] 175[6.89] MVC 500 253,25 [9.97] 199,26 [7.85] 37,0 [1.46]
MV 630 240,0 [9.45] 186[7.32] MVC 630 263,75 [10.38] 209,76 [8.25] 47,5 [1.87]
MV 800 254,0 [10.0] 200[7.87] MVC 800 277,75 [10.94] 223,76 [8.81] 61,5 [2.42]
* The width of the roll-gerotor is 4 mm [.157 in.] greater than L1.

44
MV
MOTORS

DIMENSIONS AND MOUNTING DATA - MVW

K Shaft
SH Shaft
C Shaft CO Shaft

Shaft Dim.
See Page 50
105 [4.134]

82 [3.228]

108 [4.252]
Flange Dim.
See Page 46

85 [3.346]
L1

T
L2

max 145 [5.709]

max L

Port A
Port Dim.
See Page 46
Port B

C: 4xM12 - 12 mm [.47 in] depth

P(A,B): 2xG1 - 20 mm [.79 in] depth
T: G 1/4 - 12 mm [.47 in] depth

Standard Rotation Reverse Rotation

Viewed from Shaft End Viewed from Shaft End
Port A Pressurized - CW Port A Pressurized - CCW
Port B Pressurized - CCW
mm [in]
Port B Pressurized - CW

Type L, mm [in] L2, mm [in] *L1, mm [in]

MVW 315 146 [5.75] 92 [3.62] 22,0 [ .87]
MVW 400 153 [6.02] 99 [3.90] 29,0 [1.14]
MVW 500 161 [6.34] 107 [4.21] 37,0 [1.46]
MVW 630 172 [6.77] 118 [4.65] 47,5 [1.87]
MVW 800 185 [7.28] 132 [5.20] 61,5 [2.42]

* The width of the roll-gerotor is 4 mm [.157 in.] greater than L 1.

45
MV
MOTORS
MOUNTING
Square Mount (4 Holes)
T
max 179 60 40
[7.047] [2.362] [1.575]

[2.717]
69

[6.299 -.0025 ]
ø160 -0,063
[3.504±.0394]
max 179

ø89±1
[7.047]

ø200±0,4 4xø18 20 11
[7.874±.0157] [.708] [.787] [.433] C SAE C Mount
147
[5.787]
T 85
[3.346] 14 +0,2
[.551+.0078 ]

[6.181]

[5.0 -.0019]
ø127 -0,05
[5.787]

157
147

ø162±0,4 4xø14,3 20
[6.378±.0157] [.563] [.787]

W Wheel Mount
20 10
ø224±0,4 [.787] [.394]
[8.819±.0157] 3,6 79
[.142] [3.11]
[7.638 -.0028 ]

[5.827 -.0039 ]
ø194 -0,072

[3.504±.0394]

[7.087 -.0025 ]
ø180 -0,063
ø148 -0,1
max 198

ø89±1
[7.795]

[3.346]
85

4xø18 108
[.708] T [4.252]
max 198
[7.795]

PORTS
Side Ports

13,5±0,5 13,5±0,5
C: 4xM12 - 12 mm [.47 in] depth
[.921±.0197]

[.531±.0197] [.531±.0197]
23,4±0,5

81 P(A,B): 2xG1 - 20 mm [.79 in] depth

C
[.984±.0118]

[3.189]
T: G 1/4 - 12 mm [.47 in] depth
P(A, B)
25±0,3
[.921±.0197]
23,4±0,5

Standard Rotation
Viewed from Shaft End
Port A Pressurized - CW
Port B Pressurized - CCW
[.921±.0197]
23,4±0,5

Reverse Rotation
[.984±.0118]

Viewed from Shaft End

25±0,3

Port A Pressurized - CCW

[.921±.0197]
23,4±0,5

13,5±0,5 13,5±0,5 Port B Pressurized - CW

[.531±.0197] [.531±.0197]

24±0,6
[.945±.0236]
mm [in]
46
MV
MOTORS
DIMENSIONS AND MOUNTING
ø140 -0,063 S Short Mount
[5.112 -.0025 ] ø207
28 [8.150]
Involute Spline
[1.102] 16 DP 10/20
ANS B92.1-1976
51 max
[2.008]

[.315]
“O” Ring 140x3

8
[5.512x.118in]

[.787]

[1.378]
20

35
T 84
Port A Port B [3.307]
L2

L1
max L
[.531±.0197]

25±0,3 25±0,3
13,5±0,5

[.984±.0118] [.984±.0118]

C
[.531±.0197]
13,5±0,5
[.945±.0236]
24±0,6

P(A,B) 23,4±0,5 23,4±0,5 Standard Rotation max 77 81

[.921±.0197] [.921±.0197] Viewed from Shaft End [3.0315] [3.189]
23,4±0,5 23,4±0,5
[.921±.0197] [.921±.0197]
Port A Pressurized - CW
58
Port B Pressurized - CCW 4xø14 [2.283]
[.551]
Reverse Rotation
C: 4xM12 - 12 mm [.47 in] depth Viewed from Shaft End
P(A,B): 2xG1 - 20 mm [.79 in] depth Port A Pressurized - CCW ø6 [.236]
T: G 1/4 - 12 mm [.47 in] depth Port B Pressurized - CW Drain port

Type L, mm [in] L2, mm [in] *L1, mm [in]

[7.087±.0157]

[1.102]
MVS 315 171[6.73] 117[4.61] 22,0 [.87]
ø180±0,4

28
MVS 400 179[7.05] 124[4.88] 29,0 [1.14]
MVS 500 186[7.32] 132[5.20] 37,0 [1.46]
MVS 630 197[7.76] 143[5.63] 47,5 [1.87]
MVS 800 211[8.31] 157[6.18] 61,5 [2.42]

* The width of the roll-gerotor is 4 mm [.157 in] greater than L1.

DIMENSIONS OF THE ATTACHED COMPONENT

76±0,3
Internal Spline
16 DP 10/20
53±0,3
[2.087±.0118]
[2.992±.0118]
MVS
9±0,5
ANS B92.1-1976 [.354±.0197] T
0,1 K
I

0,25 K
[7.087±.0157]
[5.819±.0039]
[1.811±.0078]

[4.33 +.0157]
ø147,8±0,1
[2.165 +.0512 ]
min ø6
[.236]

[5.112+.0025 ]

[2.598+.0197 ]
ø110 +0,4
ø180±0,4
ø140 +0,063
ø46±0,2

min ø60
[2.362]
ø55 +1,3

ø66 +0,5

J
F 32±0,5
[1.26±.0197] G
H
2,3±0,05 30±0,5
[.0905±.00196] [1.181±.0197]
min 18
[.7087] F : Oil circulation hole
J: 4xM12-18 mm [.709 in] depth, 900
G: Internal drain channel
K: Conical seal ring
H: Hardened stop plate
T: Drain connection G1/4 - 12 mm [.47 in] depth
mm [in] I : O-Ring 140x3mm [5.512x.118in]
47
MV
MOTORS
DIMENSIONS AND MOUNTING
V Very Short Mount
-0,04
ø122 -0,12
-.0016
[4.803-.0047 ] Involute Spline
16 DP 10/20
ANS B92.1-1976

min 75,55 [2.974]

max 77,7 [3.059]

[0.945±.0039]
24±0,1
4xM16

“O”-ring 115x3

L3
[4.527x.118in]

25±0,3 25±0,3 L1
C
[.531±.0197]
L2

13,5±0,5

[.984±.0118] [.984±.0118]

max L
[.531±.0197]
13,5±0,5

Standard Rotation
Viewed from Shaft End
[.531±.0197]

Port A Pressurized - CW
13,5±0,5
[.945±.0236]
24±0,6

Port B Pressurized - CCW

[.531±.0197]

Reverse Rotation
13,5±0,5

P(A,B) 23,4±0,5 23,4±0,5 Viewed from Shaft End 157

[.921±.0197] [.921±.0197] Port A Pressurized - CCW [6.181]
23,4±0,5 23,4±0,5 Port B Pressurized - CW
[.921±.0197] [.921±.0197] 145
[5.709]
ø145±0,4
C: 4xM12 - 12 mm [.47 in] depth ø6 [.236]
[5.709±.0157]

P(A,B): 2xG1 - 20 mm [.79 in] depth Drain port

Type L, mm[in.] L2, mm [in] L3, mm [in] *L1, mm [in]

MVV 315 121,5[4.78] 68[2.68] 29,5[1.16] 22,0 [.87]
[5.709]
145

MVV 400 128,5[5.06] 75[2.95] 32,5[1.28] 29,0 [1.14]

MVV 500 136,5[5.37] 83[3.27] 34,5[1.36] 37,0 [1.46]
MVV 630 147,0[5.79] 93[3.66] 34,0[1.34] 47,5 [1.87]
MVV 800 161,0[6.34] 107,5[4.23] 30,0[1.18] 61,5 [2.42]
52,6 82
* The width of the roll-gerotor is 4 mm [.157 in] greater than L1. [2.071] [3.228]

DIMENSIONS OF THE ATTACHED COMPONENT

Internal Spline
16 DP 10/20 +1,5
MVV
78 +0,5 23,5-0,3
ANS B92.1-1976, cl.5
+.059
[3.071+.0197 ] [.925 -.0118]
1,8+0,2
H [.0708+.0078 ]
A
4xM16

ø0,2

F I
[.63]

A
0,25 K
K
min 7
[.275]
[5.709±.0078]
[.236]

[2.165 +.0512]
min ø6

]
[1.811 +.0078]

+.0024
[4.803+.0078

1,5±0,4
max ø72

+0,02

145±0,2
ø122 +0,06
[2.835]
ø55 +1,3
ø46 +0,2

[.059±.0157]

0,006
max R0,5 0,1 K
max R.0197 1,6

0
20
G

F: Oil circulation hole

I : O- Ring 115x3mm [4.527x.118in]
32±0,5 min 36 H: Hardened stop plate
[1.26±.0197] [1.417] K: Conical seal ring
G: Internal drain channel
mm [in]
48
MV
MOTORS
DRAIN CONNECTION
A drain line has to be used when pressure in the return line can exceed the permissible pressure. It can be
connected:
- For MVS to the drain port of the motor;
- For MVV to the drain connection of the attached component. The maximum pressure in the drain line is limited by
the attached component and its shaft seal.
The drain line must be possible for oil to flow freely between motor and attached component and must be led to the
tank. The maximum pressure in the drain line is limited by the attached component and its seal.

INTERNAL SPLINE DATA FOR THE ATTACHED COMPONENT

Standard ANS B92.1-1976, class 5
[m=2.54; corrected x.m=+1,0]
Fillet Root Side Fit mm inch
Number of Teeth z 16 16
Diametral Pitch DP 10/20 10/20
Pressure Angle 300 300
Pitch Dia. D 40,640 1.6
+0,4
Major Dia. Dri 45,2 1.796÷1.780
+0,039
Minor Dia. Di 38,5 1.5175÷1.516 L
Space Width [Circular] Lo 5,18±0,037 .2055÷.2025
Fillet Radius R 0,4 .015
Max. Measurement L 32,47 +0,15 1.284÷1.278 Hardening Specification:
HV=750±50 on the surface.
between Pins HV=560 at 0,7±0,2 mm [.035±.019in] case depth
Pin Dia. d 5,6±0,001 .22051÷.22043 Material: 20 MoCr4 EN 10084 or better.

MOTOR WITH TACHO CONNECTION

33 max L
[1.299]

ø3
[.118]
[1.89]
ø48

[.315]
ø8

5
[.197]

20 16
[.787] [.63]
ø34 4xM5
[1.339] 8 [.315] deep

MAX. PERMISSIBLE SHAFT SEAL PRESSURE for MV motors

Max. return pressure without drain line or
P P max. pressure in the drain line
PSI bar
1200

1000 1: Drawing for High Pressure Seal ("U" Seal)

800 2: Drawing for Standard Shaft Seal
600
1

400 2 - continuous operations

200 - intermittent operations

0 -1
min
mm [in]
49
MV
MOTORS

SHAFT EXTENSIONS

C - ø50 straight, Parallel key A14x9x70 DIN 6885 CO - ø2¼"[57,15] straight,Parallel key ½ "x½"x 2¼" BS46
12,72 -0,02 79
14 -0,043 79 [3.11]
[.5 -.0008 ]
[.551-.0017 ] [3.11]

ø57,15 -0,015
[2.086 -.0079 ]
+.0079 ]

+.0001 ]
+0,018
ø50 +0,002
[2.086 +.0197

[2.25 -.0006 ]
[1.968+.0007

62,9 -0,2

[2.362]
[2.362]
+0,5
53 +0,2

ø60
ø60

M12 3/8-16 UNC

min 26 [1.024] deep
min 25 [.984] deep

SH -ø21/ 8"splined, 16 DP 8/16 ANS B92.1-1976 K -tapered 1:10, Parallel key B16x10x32 DIN 6885
S=65
70 7
Tightening Torque
[2.756] A [.275]
A-A 70±1 daNm
16 -0,043
+2 40 [6196±88.5 lb-in]
56 [.63 -.0017]
[1.575]
[2.205+.078 ]

[.315]
ø8
ø53,975 -0,025
[2.125 -.001 ]

[3.071]
[2.362]

M42x3
[2.362]

ø60

ø78
ø60

[1.27 -.0079 ]
32,25 -0,2

79
M12 A
[3.11] 6
min 26 [1.024] deep
Taper 1:10 105 [.236]
[4.134]

mm [in]

ORDER CODE
1 2 3 4 5 6

Pos.1 - Mounting Flange Pos. 3 - Shaft extensions*

omit - Square mount, four holes omit - for S and V mounting flange
C - SAE C mount C - ø50 straight, Parallel key A14x9x70 DIN6885
W - Wheel mount CO - ø2¼" straight, Parallel key ½ "x½"x 2¼" BS46
S - Short mount SH
1
- ø2 /8" splined,ANS B92.1-1976
V - Very short mount K - ø60 tapered 1:10, Parallel key B16x10x32 DIN6885
Pos. 4 - Shaft Seal Version (see page 49)
Pos.2 - Displacement code
omit - Low pressure shaft seal
315
3 3
- 314,5 cm /rev [19.18 in /rev]
U - High pressure shaft seal
400 - 400,9 cm3/rev [24.45 in3/rev]
500 - 499,6 cm3/rev [30.48 in3/rev] Pos. 5 - Special Features (see page 51)
630 - 629,1 cm3/rev [38.38 in3/rev] Pos. 6 - Design Series
800 - 801,8 cm3/rev [48.91 in3/rev] omit - Factory specified

NOTES:
* The permissible output torque for shafts must not be exceeded!
The hydraulic motors are mangano- phosphatized as standard.

50
MOTOR SPECIAL FEATURES

Motor type
Special
Feature Order
Description Code

MV
MT
Speed Sensor* RS O O O

Tacho Connection** T O O O

Reinforced motor HD - O O

Low Leakage LL O O O

Low Speed Valving LSV O O O

Reverse Rotation R O O O

Paint*** P O O O

Corrosion
PC O O O
Protected Paint***

Check Valves S S S

O Optional
- Not applicable
S Standard

* for sensor ordering see pages 52-53.

** only for side ports.
*** color at customer's request.
****without check valves for "HD" option.

For more information about HD option please contact with "M+S Hydraulic".

51
MOTORS WITH SPEED SENSOR

MS...RS max 50
[1.97]
M12x1

max 110
[4.33]
MT...RS max 54
M12x1 [2.13]

max 122
[4.8]

MV...RS max 61
M12x1 [2.4]
127 max
[5.0]

mm [in]
52
SPEED
SENSOR

MOTORS

TECHNICAL DATA OF THE SPEED SENSOR

Technical data Output signal

U
Frequency range 0...15 000 Hz
Uhigh>Ud.c.-2V
Output PNP, NPN
Power supply 10...36 VDC
Current input 20 mA (@24 VDC)
Ambient Temperature -40...+1250C [-40...+2570F] Ulow<2V
Protection IP 67
Plug connector M12-Series f1 f2 f
Mounting principle ISO 6149 f1=f2±10%
Load max.:Ihigh=Ilow<50mA

Motor type MS MT MV
Pulses per revolution 54 84 102

Wiring diagrams

PNP NPN

RLoad [kΩ]=Ud.c. [V]/Imax [mA]

Stick type Order Code for Speed Sensor

Terminal Cable Sensor Output

4 3 No. Connection Output Code type Electric connection
1 Ud.c. Brown RSN NPN Connector BINDER 713 series
2 No connection White
RSP PNP Connector BINDER 713 series
3 0V Blue
1 2 RSNL5 NPN Cable output 3x0,25; 5 m [196 in] long
4 Output signal Black
RSPL5 PNP Cable output 3x0,25; 5 m [196 in] long

NOTE: *- The speed sensor is not fitted at the factory, but is supplied in a plastic bag with the motor.
For installation see enclosed instructions.

53
APPLICATION CALCULATION
VEHICLE DRIVE CALCULATIONS
1.Motor speed: n, RPM 4. Acceleration force: FA, daN [lbs]
Force FA necessary for acceleration from 0 to maximum
2,65 x vkm x i 168 x vml x i
n= n= speed v and time t can be calculated with a formula:
Rm Rin
vkm- vehicle speed, km/h; vkm x G vml x G
vml- vehicle speed, mil/h; FA= , [daN] FA= , [lbs];
Rm- wheel rolling radius, m;
3,6 x t 22 x t
Rin- wheel rolling radius, in;
i- gear ratio between motor and wheels.
If no gearbox, use i=1. FA- acceleration force, daN [lbs];
t- time, [s].
2.Rolling resistance: RR, daN [lbs]
The resistance force resulted in wheels contact with 5.Tractive effort: DP,daN [lbs]
different surfaces: Tractive effort DP is the additional force of trailer. This value
RR=G x r will be established as follows:
G- total weight loaded on vehicle, daN [lbs]; -acc.to constructor's assessment;
r- rolling resistance coefficient (Table 1). -as calculating forces in items 2, 3 and 4 of trailer; the
calculated sum corresponds to the tractive effort requested.
Table 1
Rolling resistance coefficient 6.Total tractive effort: TE, daN [lbs]
In case of rubber tire rolling on different surfaces Total tractive effort TE is total effort necessary for vehicle
motion; that the sum of forces calculated in items from 2 to 5
Surface r and increased with 10 % because of air resistance.
Concrete- faultless 0.010
TE=1,1x(RR + GR + FA + DP)
Concrete- good 0.015
RR - force acquired to overcome the rolling resistance;
Concrete- bad 0.020
GR- force acquired to slope upwards;
Asphalt- faultless 0.012 FA- force acquired to accelerate (acceleration force);
Asphalt- good 0.017 DP- additional tractive effort (trailer).
Asphalt- bad 0.022 7.Motor Torque moment: M, daNm [lb-in]
Macadam- faultless 0.015 Necessary torque moment for every hydraulic motor:
Macadam- good 0.022
M=
Macadam- bad 0.037
Snow- 5 cm 0.025 N- motor numbers;
Snow- 10 cm 0.037 hM- mechanical gear efficiency (if it is available).
Polluted covering- smooth 0.025
8.Cohesion between tire and road covering: MW, daNm [lb-in]
Polluted covering- sandy 0.040
Mud 0.037÷0.150 MW=
Sand- Gravel 0.060÷0.150
Sand- loose 0.160÷0.300
To avoid wheel slipping, the following condition should be
3.Grade resistance: GR, daN [lbs] observed MW > M
f - frictional factor;
GW- total weight over the wheels, daN [lbs] .
a- gradient negotiation angle (Table 2)
Table 2 Table 3
Grade Grade Frictional factor
% Degrees % Degrees Surface f
1% 0º 35' 12% 6º 5' Steel on steel 0.15 ÷ 0.20
2% 1º 9' 15% 8º 31' Rubber tire on polluted surface 0.5 ÷ 0.7
5% 2º 51' 20% 11º 19' Rubber tire on asphalt 0.8 ÷ 1.0
6% 3º 26' 25% 14º 3'
Rubber tire on concrete 0.8 ÷ 1.0
8% 4º 35' 32% 18º
Rubber tire on grass 0.4
10% 5º 43' 60% 31º

54
HYDRAULIC

MOTORS

9.Radial motor loading: Prad , daN [lbs]

When motor is used for vehicle motion with wheels
mounted directly on motor shaft, the total radial
Prad
GW
loading of motor shaft Prad is a sum of motion force and
weight force acting on one wheel.
M
R
GW - Weight held by wheel;
Prad - Total radial loading of motor shaft; M 2

M/R- Motion force. 2

Prad= G W + R

In accordance with calculated loadings the suitable motor from the catalogue is selected.

DRAINAGE SPACE AND DRAINAGE PRESSURE

Advantages in oil drainage from drain space: Cleaning; Cooling and Seal lifetime prolonging.

Series connection

Parallel connection

55
WARRANTY

M+S Hydraulic warrants, that its products, supplied directly to original equipment
manufacturer, authorized distributor or other customer, will be free of defects in material or
workmanship at the time of shipment from M+S Hydraulic and will conform to the products
technical documentation (drawings and specifications) under sale agreement with Buyer.

This warranty will apply only to defects appearing within applicable Warranty period,
mentioned below. If Buyer notifies M+S Hydraulic within the Warranty period about any
such defects, M+S, at its sole option will replace or repair the defective products or their
parts found by M+S Hydraulic to be defective in material or workmanship.

THE FOREGOING LIMITED WARRANTY IS AVAILABLE ONLY IF “M+S HYDRAULIC”

IS PROMPTLY NOTIFIED IN WRITTEN OF THE ALLEGED DEFECT AND DOES NOT
COVER FAILURE TO FUNCTION CAUSED BY DAMAGE TO THE PRODUCT,
IMPROPER INSTALLATION, UNREASONABLE USE OR ABUSE OF THE PRODUCT,
FAILURE TO PROVIDE OR USE OF IMPROPER MAINTENANCE OR USUAL,
DEGRADATION OF THE PRODUCT DUE TO PHYSICAL ENVIRONMENTS OF AN
USUAL NATURE. THE FOREGOING REMEDIES ARE THE SOLE AND EXCLUSIVE
REMEDIES AVAILABLE TO CUSTOMER. To facilitate the inspection, M+S Hydraulic may
require return of the product/part, which Buyer claims to be defective.
M+S Hydraulic shall not be liable for labor costs or any other expenses incurred during
the disassembling or reinstalling of the product/part.
In case the claimed products are returned to M+S Hydraulic in bad condition: dirty,
disassembled, with damaged or missing parts during transportation, the warranty will be
considered as not applicable and the products will not be liable to repair.

Warranty periods

New products: The Warranty period is limited to 24 consecutive months (2 years) from
the date of production of the product.

Repaired products: If the product is repaired in M+S Hydraulic during its warranty
period, the warranty period of the repaired item shall continue for the balance of original
Warranty period or for a period equal to 50% of the original new product Warranty period,
whichever is later.

Spare parts: The Warranty period for Spare parts is 12 consecutive months (1 year)
from the dispatch date of such parts from M+S Hydraulic.

LIMITATION OF LIABILITY M+S Hydraulic's liability for claim of any kind, for loss or
damage arising out of, connected with or resulting from an order, or from the performance
or branch thereof, or from the design, manufacture, sale delivery, operation or use of any of
its products shall be limited to, at M+S 's sole option, replacement, repair of any defective
product or the issuance of a credit to Customer against any future purchases. Cash
refunds will not be made under any circumstances and Customer will not be entitled to
recover any damages of any kind against M+S Hydraulic, including but not limited to
incidental or consequential damages, whether direct or indirect, known or unknown,
foreseen or unforeseen.

Ond The Pulse 3 PDF
100% (4)
Ond The Pulse 3 PDF
155 pages
Bauer Motors PDF
0% (1)
Bauer Motors PDF
30 pages
MCR 5
100% (1)
MCR 5
18 pages
Parker Re15196 - 2013-12
100% (1)
Parker Re15196 - 2013-12
16 pages
Bauer Nilson PDF
100% (1)
Bauer Nilson PDF
29 pages
Section 3 - Hand Pumps
No ratings yet
Section 3 - Hand Pumps
3 pages
E2 Diskvalve
No ratings yet
E2 Diskvalve
56 pages
E1 Spoolvalve
No ratings yet
E1 Spoolvalve
126 pages
E3 Heavy Duty
No ratings yet
E3 Heavy Duty
53 pages
Sae3-Heavy Duty
No ratings yet
Sae3-Heavy Duty
53 pages
3 Гидромоторы Героторные и Геролерные
No ratings yet
3 Гидромоторы Героторные и Геролерные
238 pages
SAE2-DISCVALVE
No ratings yet
SAE2-DISCVALVE
63 pages
Sae2 Discvalve
No ratings yet
Sae2 Discvalve
64 pages
Sae1 Spoolvalve
No ratings yet
Sae1 Spoolvalve
110 pages
BFP OrbitalMotor AxialPiston
No ratings yet
BFP OrbitalMotor AxialPiston
109 pages
Motores Hidráulicos PDF
No ratings yet
Motores Hidráulicos PDF
106 pages
Mo to Thuy Luc-catalo
No ratings yet
Mo to Thuy Luc-catalo
200 pages
Select the Right Motor for Your Hydraulic Applications
No ratings yet
Select the Right Motor for Your Hydraulic Applications
5 pages
Hydraulic Motors: What Is A Hydraulic Motor and Why Do You Need It?
No ratings yet
Hydraulic Motors: What Is A Hydraulic Motor and Why Do You Need It?
9 pages
Fluid Mechanics Pesentation
No ratings yet
Fluid Mechanics Pesentation
29 pages
Eaton Hydraulic Motors
No ratings yet
Eaton Hydraulic Motors
336 pages
M+S Hydro MotorCatalogue
No ratings yet
M+S Hydro MotorCatalogue
130 pages
Hydraulic Motors: What Is A Hydraulic Motor and Why Do You Need It?
No ratings yet
Hydraulic Motors: What Is A Hydraulic Motor and Why Do You Need It?
7 pages
Motor Hidrolik 1
No ratings yet
Motor Hidrolik 1
47 pages
Radial Piston Hydraulic Motor: LD Series MD Series MDS Series 820 Series HD Series
No ratings yet
Radial Piston Hydraulic Motor: LD Series MD Series MDS Series 820 Series HD Series
7 pages
2 +Hydraulic+Actuators+-+Book
100% (1)
2 +Hydraulic+Actuators+-+Book
27 pages
10 MV 1
No ratings yet
10 MV 1
10 pages
Catalogo MB
No ratings yet
Catalogo MB
146 pages
Pleiger Hydraulik: Operating Instructions Radial Piston Motor MO-05 / MO-08
No ratings yet
Pleiger Hydraulik: Operating Instructions Radial Piston Motor MO-05 / MO-08
12 pages
Re15206 2009-07 PDF
No ratings yet
Re15206 2009-07 PDF
18 pages
Char Lynn Spool Valve Motors
100% (1)
Char Lynn Spool Valve Motors
106 pages
Lecture 1 Intro To Motors
No ratings yet
Lecture 1 Intro To Motors
11 pages
Eaton
No ratings yet
Eaton
157 pages
M Series Bent Axis Motor Iso
No ratings yet
M Series Bent Axis Motor Iso
24 pages
M GB Net
No ratings yet
M GB Net
28 pages
Rexroth Mcr5 Motors
100% (2)
Rexroth Mcr5 Motors
18 pages
Hydraulic Motor Curve 1
No ratings yet
Hydraulic Motor Curve 1
29 pages
Radial Piston Motor Bosch Rexroth MCR 1422868715
100% (2)
Radial Piston Motor Bosch Rexroth MCR 1422868715
14 pages
Fluid Power Fluid Power Equipment Tutorial - Hydraulic and Pneumatic Motors
No ratings yet
Fluid Power Fluid Power Equipment Tutorial - Hydraulic and Pneumatic Motors
12 pages
YPT Orbital Motors Complete
No ratings yet
YPT Orbital Motors Complete
176 pages
Orbital Cat
No ratings yet
Orbital Cat
32 pages
ME080 Section 6 - Hydraulic Motors
No ratings yet
ME080 Section 6 - Hydraulic Motors
56 pages
Radial Piston Motors For Industrial Applications MCR-D Mcr-E
No ratings yet
Radial Piston Motors For Industrial Applications MCR-D Mcr-E
16 pages
Radial Piston Motor (Multi-Stroke) MCR10: RE 15207/07.10 1/16 Replaces: 02.98
No ratings yet
Radial Piston Motor (Multi-Stroke) MCR10: RE 15207/07.10 1/16 Replaces: 02.98
16 pages
Motor MFB 10 Uy 31 PDF
No ratings yet
Motor MFB 10 Uy 31 PDF
11 pages
Motor MCR 03
No ratings yet
Motor MCR 03
18 pages
Pneumatic Rotary Actuators & Airmotors Radial Piston Air Motors - P1V-P
No ratings yet
Pneumatic Rotary Actuators & Airmotors Radial Piston Air Motors - P1V-P
33 pages
7-MS-1
No ratings yet
7-MS-1
20 pages
Char Lynn 6k
No ratings yet
Char Lynn 6k
25 pages
Radial Piston Motor (Multi Stroke) Type MCR 5: RE 15 206/06.06 1/16 Replaces: 02.98
0% (1)
Radial Piston Motor (Multi Stroke) Type MCR 5: RE 15 206/06.06 1/16 Replaces: 02.98
16 pages
Hydraulic Motors: Brought To You By: Demetri Preonas Greg Unverferth
No ratings yet
Hydraulic Motors: Brought To You By: Demetri Preonas Greg Unverferth
29 pages
Technical Information: General, Orbital Motors
No ratings yet
Technical Information: General, Orbital Motors
32 pages
A2-MEDIUM-DUTY-VARIABLE-MOTOR - MA2V V1.3a
No ratings yet
A2-MEDIUM-DUTY-VARIABLE-MOTOR - MA2V V1.3a
26 pages
Hydraulic Motor
No ratings yet
Hydraulic Motor
18 pages
Motor Hidráulico (Rotor) Serie 16 y 17 Rotary Power SMA 1600 SMA 2200
No ratings yet
Motor Hidráulico (Rotor) Serie 16 y 17 Rotary Power SMA 1600 SMA 2200
16 pages
WS-Orbital-Motors-Technical-Information
No ratings yet
WS-Orbital-Motors-Technical-Information
36 pages
Hydraulic Motors
No ratings yet
Hydraulic Motors
22 pages
Chapter - 4: Basic Components of Hydraulic &pneumatic Systems
No ratings yet
Chapter - 4: Basic Components of Hydraulic &pneumatic Systems
98 pages
A2-MEDIUM-DUTY-VARIABLE-MOTOR - MA2V v1.4
No ratings yet
A2-MEDIUM-DUTY-VARIABLE-MOTOR - MA2V v1.4
30 pages
CNC Machining Handbook: Building, Programming, and Implementation
From Everand
CNC Machining Handbook: Building, Programming, and Implementation
Alan Overby
No ratings yet
Speed Changers, Drives & Gears World Summary: Market Values & Financials by Country
From Everand
Speed Changers, Drives & Gears World Summary: Market Values & Financials by Country
Editorial DataGroup
No ratings yet
The IT Factory
From Everand
The IT Factory
H.J.C. van Aken
No ratings yet
НАСОСЫ РУЧНЫЕ
No ratings yet
НАСОСЫ РУЧНЫЕ
14 pages
Hydraulic Side Mount Tanks 15L-80L
No ratings yet
Hydraulic Side Mount Tanks 15L-80L
1 page
Cat Tubefittings en
No ratings yet
Cat Tubefittings en
208 pages
MH Parts Catalogus 2021
100% (2)
MH Parts Catalogus 2021
112 pages
P.T.O. Gearboxes: Technical Catalogue
No ratings yet
P.T.O. Gearboxes: Technical Catalogue
48 pages
Hipo Mak
No ratings yet
Hipo Mak
74 pages
PV48K-Manual Section 7 Page 5
No ratings yet
PV48K-Manual Section 7 Page 5
42 pages
Номенклатура Оборудования 1 (Данфос)
No ratings yet
Номенклатура Оборудования 1 (Данфос)
100 pages
Catalogue BD
100% (1)
Catalogue BD
228 pages
Fixed Displacement Bent Axis Piston Pumps: For Truck Applications
No ratings yet
Fixed Displacement Bent Axis Piston Pumps: For Truck Applications
4 pages
P80ED3 G 12,24VDC Badestnost
No ratings yet
P80ED3 G 12,24VDC Badestnost
2 pages
Catalogue Standart Gear Pumps
No ratings yet
Catalogue Standart Gear Pumps
8 pages
SVV-90 Гидрораспределитель соленоидный Badestnost
No ratings yet
SVV-90 Гидрораспределитель соленоидный Badestnost
4 pages
KS180 Badestnost От 1 До 12 Секций
No ratings yet
KS180 Badestnost От 1 До 12 Секций
7 pages
Turolla Hydraulic Gear Pumps Group2 Catalogue en l1016341
No ratings yet
Turolla Hydraulic Gear Pumps Group2 Catalogue en l1016341
44 pages
V68.19.4Z and Earlier Summary of Firmware Release
No ratings yet
V68.19.4Z and Earlier Summary of Firmware Release
20 pages
Stok Opname BB Maret 2021 Validasi
No ratings yet
Stok Opname BB Maret 2021 Validasi
11 pages
Lesson4 Pocket Money 9th Form
100% (1)
Lesson4 Pocket Money 9th Form
3 pages
MF-218 Piping and Miscellaneous Practice in Engine Room PDF
No ratings yet
MF-218 Piping and Miscellaneous Practice in Engine Room PDF
35 pages
Experiments on drag-reducing surfaces and their optimization with an adjustable geometry
No ratings yet
Experiments on drag-reducing surfaces and their optimization with an adjustable geometry
29 pages
Definition and Objective of An Assurance Engagement
No ratings yet
Definition and Objective of An Assurance Engagement
3 pages
Microsoft Official Course: Installing and Configuring The Hyper-V Role
No ratings yet
Microsoft Official Course: Installing and Configuring The Hyper-V Role
43 pages
Test Bank for Health Psychology: Biopsychosocial Interactions, 9th Edition, Edward P. Sarafino Timothy W. Smith - Free Download Available To Read All Chapters
100% (8)
Test Bank for Health Psychology: Biopsychosocial Interactions, 9th Edition, Edward P. Sarafino Timothy W. Smith - Free Download Available To Read All Chapters
30 pages
Salary Slip Format in Excel
No ratings yet
Salary Slip Format in Excel
12 pages
Quay Et Al (2022) Dewey's Education Through Occupations As Being-Doing-Knowing Creative Learning Units
No ratings yet
Quay Et Al (2022) Dewey's Education Through Occupations As Being-Doing-Knowing Creative Learning Units
17 pages
Lab (Feed Formulation)
No ratings yet
Lab (Feed Formulation)
4 pages
PCE1-M: Fundamentals of Surveying
No ratings yet
PCE1-M: Fundamentals of Surveying
22 pages
Buffing Process in Manufacturing
No ratings yet
Buffing Process in Manufacturing
4 pages
Integration of Git Java and Maven To Jenkins
No ratings yet
Integration of Git Java and Maven To Jenkins
2 pages
DHM-T72X10FS
No ratings yet
DHM-T72X10FS
2 pages
Seasonal S
No ratings yet
Seasonal S
10 pages
LBN Accreditation Contract 2022
No ratings yet
LBN Accreditation Contract 2022
7 pages
Als Effectiveness Final
No ratings yet
Als Effectiveness Final
33 pages
Guy Wire Hardware For Set # 1 at Elev 75.00 FT
No ratings yet
Guy Wire Hardware For Set # 1 at Elev 75.00 FT
1 page
Buffet Service
No ratings yet
Buffet Service
14 pages
Financial Management Theory and Practice 14th Edition Brigham Test Bank download pdf
100% (15)
Financial Management Theory and Practice 14th Edition Brigham Test Bank download pdf
66 pages
AM of Ceramic Based Materials
No ratings yet
AM of Ceramic Based Materials
26 pages
Gov - Ininformation20brochure 2024-25 PDF
No ratings yet
Gov - Ininformation20brochure 2024-25 PDF
5 pages
73 Magazine - March 2002
100% (1)
73 Magazine - March 2002
68 pages
Draft Pricing File SOR Event Item
No ratings yet
Draft Pricing File SOR Event Item
5 pages
Data Sheet
No ratings yet
Data Sheet
7 pages
TTL 1 Course Outline
No ratings yet
TTL 1 Course Outline
4 pages
Accessories Catalogue-Mindray-2015
No ratings yet
Accessories Catalogue-Mindray-2015
66 pages
Database Lab Manual
No ratings yet
Database Lab Manual
90 pages