WF18FTLAADNN0# 第 1 頁，共 5 頁

Winstar Display Co., LTD

華凌光電股份有限公司
WEB: http://www.winstar.com.tw E-mail: sales@winstar.com.tw

SPECIFICATION

MODULE NO.: WF18FTLAADNN0#

General Specifications
Item Dimension Unit

Size 1.77 inch

Dot Matrix 128 x RGB x 160(TFT) dots

Module dimension 34.0(W) x 45.83(H) x 2.65(D) mm

Active area 28.03 x 35.04 mm

Dot pitch 0.073 x 0.219 mm

LCD type TFT, Normally White, Transmissive

View Direction 6 o’clock

Gray Scale Inversion Direction 12 o’clock

Aspect Ratio Portrait

IC ST7735S

Backlight Type LED, Normally White

Touch Panel Without Touch Panel

Surface Anti-Glare
*Color tone slight changed by temperature and driving voltage.

WF18FTLAADNN0# 第 2 頁，共 5 頁
Absolute Maximum Ratings
Item Symbol Min Typ Max Unit
Operating Temperature TOP -20 － +70 ℃
Storage Temperature TST -30 － +80 ℃

Electrical Characteristics
Operating conditions
Item Symbol Condition Min Typ Max Unit
Supply Voltage For Analog VCI － 2.5 2.75 4.8 V

Interface Operation Voltage IOVCC － 1.65 1.8 3.7 V

Supply LCM current ICI(mA) － - 0.9 2 mA

WF18FTLAADNN0# 第 3 頁，共 5 頁
Interface
LCM PIN Definition
Pin Symbol I/O Function
1 VLED- P Back light cathode
2 VLED+ P Back light anode
- MCU Parallel Interface Type Selection
-If Not Used, Please Fix this Pin at VDDI or DGND Level.
3 IM0

4 IM1

MCU Parallel Interface Bus and Serial Interface select

5 IM2 I IM2=’1’, Parallel Interface
IM2=’0’, Serial Interface
6 RESET P Reset signal
7-12 NC - No Connect
DB15:0] are used as MCU parallel interface data bus.
DB15-DB0(SPI -DBis the serial input/output signal in serial interface mode.
13-28 I/O
_SDA) -In serial interface, DB15:1] are not used and should be fixed
at VDDI or DGND level.
29 NC - No Connect
Read Enable in 8080 MCU Parallel Interface.
30 RD I
-If not used, please fix this pin at VDDI or DGND level.
Serial clock
31 WR I -Write Enable in MCU Parallel Interface.
-If not used, please fix this pin at VDDI or DGND level.
-Display data/command Selection Pin in MCU Interface.
-D/CX=’1’: Display Data or Parameter.
32 D/C(SPI_SCL) I -D/CX=’0’: Command Data.
-In Serial Interface, this is used as SCL.
-If not used, please fix this pin at VDDI or DGND level.
33 CS(SPI_CS) I Chip enable
34 IOVCC P Interface Operation Voltage
35 VCI P Analog Supply Voltage
36 GND P Ground
37-40 NC - No Connect

WF18FTLAADNN0# 第 4 頁，共 5 頁
Contour Drawing
PIN DESCRIPTION
NO. SYMBOL
34.00±0.2 1 VLED-
1.08 31.83±0.2 LCD 2 VLED+
2.79
1.12

2.98 28.03 AA 2.65±0.1 3 IM0

4 IM1
5 IM 2
6 RESET
7 NC
8 NC
9 NC
Pull tape
41.42±0.2 LCD

1.77"TFT 10
35.04 AA

NC
45.83±0.2

11 NC
128×3(RGB)×160 Dots
12 NC
13-27 DB15-1
28 DB0(SPI_SDA)
29 NC
30 RD
31 WR
32 D/C(SPI_SCL)
33 CS(SPI_CS)
C OM PO NEN T AR EA 34 IOVCC
24.00±0.5

YU XLYDXR AKK
35 VCI
25.8 36 G ND
5.00

3.5
37-40 NC
Stiffener Contact side
40 1 1 40
0.3±0.05 W =0.35
IM2 IM1 IM0 MPU
P0.5*39=19.5 0.5 Interface
GRAM

8080 MCU
6.12±0.5 20.5±0.1 1 0 1
16-bit bus D[15:0]
8080 MCU
1 0 0 D[7:0]
8-bit bus

0 — — 3- Line SPI (D0 : SDA)

(D/C :SCL)
(SPI_CS)

The non-specified tolerance of dimension is ±0.3 mm .

WF18FTLAADNN0# 第 5 頁，共 5 頁