WF57A2TIBCDBG0# 第 1 頁，共 6 頁

Winstar Display Co., LTD

華凌光電股份有限公司
WEB: https://www.winstar.com.tw E-mail: sales@winstar.com.tw

SPECIFICATION

MODULE NO.: WF57A2TIBCDBG0#

General Specifications
Item Dimension Unit
Size 5.7 inch
Dot Matrix 320 x RGBx240(TFT) dots
Module dimension 141.12x 101.55 x 15.24 mm
Active area 115.2 x 86.4 mm
Dot pitch 0.12 x 0.36 mm
LCD type TFT, Normally White, Transmissive
View Direction 12 o’clock
Gray Scale Inversion Direction 6 o’clock
Aspect Ratio 4:3
Backlight Type LED ,Normally White
Controller IC SSD1963 or Equivalent
TFT Interface Digital 8080 family MPU 8bit/16bit
PCAP FW Version 0x07.0x00.0x00.0x00.0xA2.0x01.0x57.0x00
PCAP IC ILI2130 or equivalent
PCAP Interface I2C
PCAP Resolution 16384*16384
Touch Pnael With PCAP
Surface Glare
*Color tone slight changed by temperature and driving voltage.

WF57A2TIBCDBG0# 第 2 頁，共 6 頁
Absolute Maximum Ratings
Item Symbol Min Typ Max Unit

Operating Temperature TOP -20 － +70 ℃

Storage Temperature TST -30 － +80 ℃

Electrical Characteristics
Operating conditions: (CON3.Pin1=GND, Pin2=VDD)
Conditio
Item Symbol Min Typ Max Unit
n
Supply Voltage For LCM VDD － 3.0 3.1 3.3 V

Supply Current For LCM IDD － － 480 720 mA

WF57A2TIBCDBG0# 第 3 頁，共 6 頁
Interface
1. LCM PIN Definition (CON3)
Pin Symbol Function
1 GND System ground pin of the IC . Connect to system ground.
2 VDD Power Supply : +3.3V
3 BLE Backlight control signal , H: On \ L: Off
4 D/C Data/Command select
5 WR Write strobe signal
6 RD Read strobe signal
7 DB0 Data bus
8 DB1 Data bus
9 DB2 Data bus
10 DB3 Data bus
11 DB4 Data bus
12 DB5 Data bus
13 DB6 Data bus
14 DB7 Data bus
15 DB8 Data bus (When select 8bits Mode, this pin is NC)
16 DB9 Data bus (When select 8bits Mode, this pin is NC)
17 DB10 Data bus (When select 8bits Mode, this pin is NC)
18 DB11 Data bus (When select 8bits Mode, this pin is NC)
19 DB12 Data bus (When select 8bits Mode, this pin is NC)
20 DB13 Data bus (When select 8bits Mode, this pin is NC)
21 DB14 Data bus (When select 8bits Mode, this pin is NC)
22 DB15 Data bus (When select 8bits Mode, this pin is NC)
23 NC No connect
24 CTP_INT CTP_ External interrupt to the host
25 CS Chip select
26 RESET Hardware reset
27 LR Left / right selection; Default L/R=H
28 UD Up/down selection; ; Default U/D=L
29 CTP_SCL CTP_SPI Slave mode, chip select, active low / I2C clock input
30 CTP_SDA CTP_ SPI Slave mode, data input / I2C data input and output

WF57A2TIBCDBG0# 第 4 頁，共 6 頁
31 CTP_RST CTP_ External Reset, Low is active
32 NC No connect
33 VLED- Power for LED Driver IC(GND)
34 VLED- Power for LED Driver IC(GND)
35 VLED+ Power for LED Driver IC(+5V)
36 VLED+ Power for LED Driver IC(+5V)

WF57A2TIBCDBG0# 第 5 頁，共 6 頁
Contour Drawing
CON3
TFT OD 141.12±0.5 PIN NO.SYMBOL PIN NO.SYMBOL
3.50 134.12
1 GND 19 DB12
2 VDD 20 DB13
7.56 126.00
3 BLE 21 DB14
0.15±0.5 TP OD 125.70 4 D/C 22 DB15
(4.10) TP AA 117.80 5 WR 23 NC
4.80±0.5 TP VA 116.40 15.24 MAX 6 RD 24 CTP_INT
(5.40) TFT AA 115.20 7.79±0.65 7 DB0 25 CS
4.27±0.5
0.15±0.5

6.05±0.45 100.50±0.5(PCB)
8 DB1 26 RESET
24.00
(3.57)

(4.67)

13.78

9 DB2 27 LR
16.80±0.5

4-
10 DB3 28 UD
11 DB4 29 CTP_SCL

(18.69)
12 DB5 30 CTP_SDA
Pull tape
13 DB6 31 CTP_RST
14 DB7 32 NC

4.00
15 DB8 33 VLED-

8.00
Lens

32.72±0.5
T:0.7mm 16 DB9 34 VLED-

320 X RGB X 240

DB10 VLED+
TFT OD 101.55±0.5

17 35
TFT AA 86.40
TP AA 89.16
TP VA 87.76
TP OD 101.25

DB11 VLED+

70.00±0.5(PCB)
18 36
74.00

82.00
CTP1
1 10

1 2
CON4

2.0 MAX
IC

Black printing
1.00 (PCB)
2-C0.15±0.1
(along the outline)

The non-specified tolerance of dimension is 0.3mm.

WF57A2TIBCDBG0# 第 6 頁，共 6 頁