T20-a

OPERATION TABLE

Illustrated parts list

111706 T-IPL35h
 Eschmann After Sales Service Department
The Eschmann After Sales Service Department is staffed and equipped to provide advice and
assistance during normal office hours. To avoid delays when making enquires, please quote the
Model and Serial Number of your Operation Table which is shown on the Serial Number plate, the
location of which is shown below. Please ensure you include all alpha and numeric digits of the
Serial Number.

The Serial Number

plate is located here

For further information visit www.eschmann.co.uk

All correspondence relating to the after sales service of Eschmann Equipment to be addressed to :
Illustrated parts list

UK Customers
Eschmann Equipment, Peter Road, Lancing, West Sussex BN15 8TJ, England.
Tel: +44 (0) 1903 765040. Fax: +44 (0) 1903 762006.

Overseas Customers
Contact your local distributor. In case of doubt contact Eschmann Equipment.

Patents and Trade marks

The ESCHMANN name and logo are registered trade marks of Eschmann Holdings Limited.
“Eschmann Equipment” is a trading name of Eschmann Holdings Limited.
“T20-a” is a trade mark of Eschmann Holdings Limited.

Patents : Worldwide Patents Pending. (Application numbers 0100981, 0100983, 0124126)

Copyright © 2004
All rights reserved. This booklet is protected by copyright. No part of it may be reproduced, stored in a
retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying,
recording or otherwise without written permission from Eschmann Holdings Limited.
The information in this publication was correct at the time of going to print. The Company, however,
reserves the right to modify or improve the equipment referred to.

If the CE mark is affixed to the product, it indicates compliance with Council Directive
93/42/EEC of 14 June 1993 concerning medical devices.

T-IPL35h March 2004

 T20-a
OPERATION TABLE

INTRODUCTION e.g. minor part identification 23, 34, 45

23 is the minor part
34 and 45 are the fixing screw and washer
1.1 Applicability
In some cases the numbers following the minor part may
This ‘Illustrated parts list’ should be referred to for details identify other small parts used on assembly (e.g. a small
of the following T20 Powered Operation Tables with Serial return spring) or a part that is not drawn and related to the
Number (SN) T2AA3A0000 or above (also see section 1.14): minor part.
REF T20-223-2301* & T20-108-2301*
REF T20-221-2301 & T20-106-2301 1.5 Common assembly items
REF T20-221-2101 & T20-106-2101
The following items are used during assembly;
Serial Numbers (SN) T2AA3H2071 or above.
* These models have Denyer style accessory side rails. 110477 .. .. Grease
670650 .. .. Threadlock
1.2 Abbreviations 695776 .. .. Cable tie (small)
The following abbreviations are used within the parts list 695777 .. .. Cable tie (large)
descriptions:
1.6 Mattresses
Ø diameter
assy. assembly The following mattresses apply to the T20 table and
csk countersunk accessories:
hd head T20-411-0001 Mattress, complete set, 50mm
hex hexagonal T20-412-0001 Mattress, complete set, 75mm
T20-421-0001 Mattress, trunk section, 50mm
id internal diameter
T20-422-0001 Mattress, trunk section, 75mm
inc includes T20-431-0001 Mattress, head or footrest, 50mm
int internal T20-432-0001 Mattress, head or footrest, 75mm
m’switch microswitch T20-441-0001 Mattress, leg section, 50mm
No. number T20-442-0001 Mattress, leg section, 75mm
od outside diameter TA-0501002 Mattress, width extender, long, 50mm
TA-0501006 Mattress, ophthalmic head section
PCA printed circuit assembly
TA-0501008 Mattress, width extender, short, 50mm
PSU power supply unit TA-0501009 Mattress, width extender, long, 75mm
Qty. quantity TA-0501010 Mattress, width extender, short, 75mm
skt socket
st/st stainless steel 1.7 Handsets
w width T00-520-0001 Infrared handset (UK side rails)
T00-521-0001 Infrared handset (Denyer side rails)
1.3 Spares T00-540-0001 Corded handset (UK side rails)
The column headed ‘Spares’ is the recommended number T00-541-0001 Corded handset (Denyer side rails)
of parts to be held on stock (for one table) for owners The infrared handset batteries can be changed ‘in the field’
overseas. If the same part appears on several ‘Parts lists’at which time the seal between the mouldings must be
the recommended quantity only appears once to eliminate changed as well, maintaining the IPX rating (see Service
duplication. If more than one T20-a table is in use within Manual). Spring clips can also be changed ‘in the field’ but
the hospital these numbers can be increased. new screws are advised (see Service Manual) also ensure
Only use the parts listed and supplied by Eschmann that the correct clip is used to match the tables side rails.
Equipment and DO NOT use equivalents. Some of the To service the infrared handset order the kit detailed below.
components have been specifically chosen for their Handset spring clip (UK) 110514 1 reqd.
strength (e.g. fixing screws) and components that look the Handset spring clip (Denyer) 111717 1 reqd.
same could compromise the strength and safety of the Spring clip screws 111908 2 reqd.
table if used. Handset kit* (UK) 111040 1 reqd.
1.4 Illustration numbering Handset kit* (Denyer) 111745 1 reqd.
* Kit contains:
For clarity on some illustrations not all duplicated parts are 1 - Seal
numbered within the figure. Also, not all fixing screws and 2 - Batteries
washers etc. are drawn, in which cases the minor part is 1 - Spring clip
numbered with the fixing screws identified as the example 6 - M2 cap head screws
following shows. 2 - M4 button head screws

T-IPL35h P3/26
1.8 Side rails 1.11 Torque settings for screws etc.
Within these parts lists the side rails detailed are the UK The values of all important torque values for screws and
standard side rails. Other side rails are available, the fixings are provided in the ‘Service manual’ and must be
‘European’ sized side rails have part numbers as follows: adhered to. Always refer to the ‘Service manual’ when
replacing parts for this and other important technical
Head section .. .. 110851
information.
Leg section .. .. 110852
Short trunk .. .. 110853
Long trunk .. .. 110854 1.12 Accessories
The Denyer side rails have part numbers as follows: See notes in the ‘Instructions for Use’ regarding the suitability
of accessories that fit onto the side rails for tables fitted
Head section .. .. 111593 with Denyer style side rails.
Leg section .. .. 111594
Short trunk .. .. 111596 T00-311-0001 Head section², UK side bars
Long trunk .. .. 111595 T00-312-0001 Head section², Euro side bars
T00-321-0001 Leg section², UK side bars
T00-322-0001 Leg section², Euro side bars
TA-0202001 Width extender², long, UK side bar
1.9 Batteries
TA-0202005 Width extender², long, Euro side bar
For the infrared handset: TA-0202007 Width extender², short, UK side bar
See section 1.7. TA-0202012 Width extender², short, Euro side bar
TA-0203001 Foot rest/extension²
For the table: TA-0301001 Lightweight leg
Note: Consult the service manual for details of battery TA-0302001 Ophthalmic head section²
management system reconditioning before changing the TA-0303004 Accessory attachment bar
batteries: TA-0401013 Accessory trolley
2 - Battery module 12V - 10Ah - 111581 TA-0404003 Footswitch
or TA-0601011 Leg abduction support
2 - Battery module 12V - 1.2Ah - 111580 81-342-00 Perineal instrument tray
81-367-85 Douche tray
391177 Mains cord
1.10 Fuse details ²
These accessories come without a mattress which
1.10.1 External fuses should be ordered separately, see section 1.6.
Mains input fuses
2 x T4A (5 x 20mm) Part No. 696768 1.13 Base covers
Battery fuses The base covers should be ordered for a specific table
2 x T20A (6.35 x 32mm) Part No. 110658 only when they are required. They come complete with all
labelling including the Serial Label which is specific to a
Note: The left hand fuse is linked to the main batteries
particular table. When ordering these items sufficient
and the right hand fuse (i.e. nearest to the backup
information will need to be supplied to ensure that the
battery switch) is linked to the backup batteries.
labelling is correct for the intended table.. Such information
Mains plug fuse is the table Serial Number, REF Number and the table
10A (type is dependent on plug which may Voltage etc.
have been changed from that originally supplied)
1.14 Serial Numbers (SN)
1.10.2 Internal fuses (only accessible by engineer)
Note: Consult the service manual for details of battery This parts list covers all design modification states of T20-a
management system reconditioning before changing a operation table. Where there is a significant change to a
battery link fuse (main or standby). parts list the modification states is changed and this is
Battery fuses (joining each battery pair) reflected in the Serial Number. To determine which parts
list is applicable to a table (if more than one is provided)
T30A blade type Part No. 704554 refer to the tables Serial Number shown on the serial label
. on the base cover. Only the first part of the Serial Number
is significant in this respect (e.g. for Serial Number
T2AC3D1023 note the first 4 digits T2AC).

P4/26 T-IPL35h
 T20-a
OPERATION TABLE

PARTS LIST INDEX

Item No. Description Cat. No. Parts List

(see Fig 1) (if applicable) No. Page
1 Head section see section 1.12 1 6
2 Leg section see section 1.12 1 6
3 Column and base, covers and looms N.A. 2 8
4 Column, top frame and looms N.A. 3 10
5 Trunks section (long) N.A. 4 12
6 Trunks section (short) N.A. 4 14
7 Powered traverse assembly N.A. 5 16
8 Traverse motor assembly N.A. 6 18
9 Base assembly (Tables SN T2AA.....)* N.A. 7a 20
9 Base assembly (Tables SN T2AC..... or later)* N.A. 7b 22
- Main electrical components N.A. 8 26

* see section 1.14.

Fig. 1 Item numbers for Part List index

T-IPL35h P5/26
PARTS LIST 1 - HEAD & LEG

NOTE: Parts 13, 14, 19 and 20

are not fitted on the head section.

Fig. 2 Head and leg section assembly

P6/26 T-IPL35h
 T20-a
OPERATION TABLE

PARTS LIST 1 - HEAD & LEG

Item No. Qty. Head Qty. Leg Part No. Description Spares

1 0 1 110390 Mattress, leg flap -

1 1 0 110391 Mattress, head flap -
2 2 2 742357 Cover, screw 4
3 2 2 710265 Screw, M6 x 30mm, csk skt st/st -
4 0 1 111043 Cover assembly, leg flap # -
4 1 0 111042 Cover assembly, head flap # -
5 4 4 710263 Screw, M6 x 20mm, csk skt st/st -
6 2 2 710260 Screw, M6 x 12mm, csk skt st/st -
7 0 1 110336 Black top, leg flap -
7 1 0 110348 Black top, head flap -
8 0 1 110335 Side arm, leg flap, right -
8 1 0 110347 Side arm, head flap, right -
9 2 2 110501 Screw, shoulder, M8 x 10 x 80mm -
10 2 2 110345 Cone washer, M8 shoulder screw -
11 0 1 110334 Side arm, leg flap, left -
11 1 0 110346 Side arm, head flap, left -
12 0 2 110338 Side rail, leg flap UK (also see section 1.8) -
12 2 0 110350 Side rail, head flap UK (also see section 1.8)-
13 0 2 709721 Screw, M8 x 16mm, button st/st -
14 0 2 110631 Washer, spring, M8 st/st -
15 2 2 700225 Pin, dowel, M10 x 55mm st/st -
16 2 2 110342 End cap, head and leg flap -
17 2 2 710219 Screw, M4 x 16mm, skt hd cap st/st* -
18 2 2 110503 Release head, gas spring -
19 0 1 110344 Cross bar, leg flap -
20 0 4 710271 Screw, M5 x 16mm, skt hd cap st/st -
21 1 1 110343 Gas spring release handle -
22 2 2 110504 Screw, M8 x 80mm skt butt hd st/st -
23 0 2 110505 Gas spring and nut, leg flap 1
23 2 0 110509 Gas spring and nut, head flap 1
24 1 1 110340 Guide pin 1
25 2 2 710889 Screw, M5 x 35mm, skt hd cap st/st -
26 1 1 110339 Guide pin, locking 1
27 2 2 110341 Mounting block, head and leg -
28 2 2 307223 Washer M5 shakeproof -
29 2 2 110506 Screw, shoulder, M6 x 8mm x 20mm -
30 2 2 110498 Mattress retainer 2
31 2 2 111521 Nut M4, Nylok 2

* On early tables this was a rolled pin (110502), screw and nut now preferred.
# Cover assemblies include the printed and applied maximum loads label.

T-IPL35h P7/26
PARTS LIST 2 - COLUMN COVERS & LOOMS

Fig. 3 Column covers and loom assembly

P8/26 T-IPL35h
 T20-a
OPERATION TABLE

PARTS LIST 2 - COLUMN COVERS & LOOMS

Item No. Qty. Part No. Description Spares

1## 1 111775 Base cover, front assy. (external pedal catch) -

or 112218 Base cover, front assy. (internal pedal catch) -
2## 1 111046 Base cover, rear assy. (external pedal catch) -
or 112219 Base cover, front assy. (internal pedal catch) -
3 1 110409 Upstand assembly -
4 1 110410 Cover support bracket rh -
5 1 110411 Cover support bracket lh -
6 1 111765 Power supply assy. (see parts list 8, Note 1) -
7 1 111674 Telescopic cover assy. (includes item 32) -
8 1 110383 Bellows -
9 2 111160 Switch panel retainer -
10 2 111162 Telescopic cover support -
11 1 111577 Handset panel loom -
12 1 110597 Switch panel loom -
13 4 110419 Bellows retainer, top -
14 1 110420 Top of column cover -
15 2 110421 Top of column end cover -
16 2 110422 Top of column side cover -
17 34 111908 Screw M4x10mm Torx pin, button Lok-pad 6
18 6 710270 M5 x 10mm cap head screw -
19 4 700083 M6 x 16mm cap head screw -
20 8 710215 M4 x 8mm cap head screw -
21 2 111491 M6 x 12mm Torx pin button head screw 2
22 4 110953 Screw M4x12mm Torx pin csk ss dl 2
23 2 110954 Screw M4x16mm Torx pin csk ss dl 2
24 4 709890 M3 x 8mm csk head screw -
25 1 111463 Column energy chain loom -
26 14 699711 Ø4x8.5mm nylon ext. rivet 10
27 4 111908 M4 x 10mm cap head screw 2
28 2 110830 Cover, crossbeam side -
29# 1 110704 Label T20 on/off switch -
30# 1 111501 Label T20 handset/ accessory -
31 2 111492 M6 machine screw insulator -
32 1 111499 Standby panel -
33# 1 111465 Mains indicator (panel) loom -
# Not drawn
## Base covers come complete with all labelling and the IR dome, see section 1.13

Note: For earth bonding see Parts List 8

T-IPL35h P9/26
PARTS LIST 3 - COLUMN , TOP FRAME & LOOMS

Note : Item 41 has its Processor

PCAs held in place by 2 cable ties
(380080) with spacer (111393).

Fig. 4 Column wrapround, top frame and loom assembly

P10/26 T-IPL35h
 T20-a
OPERATION TABLE

PARTS LIST 3 - COLUMN , TOP FRAME & LOOMS

Item No. Qty. Part No. Description Spares

1 1 110280 Wrapround welded assembly -
2* 2 110291 . . Top pivot, wrapround -
3 1 110287 Front beam, trend frame -
4 1 110288 Rear beam, trend frame -
5 2 110292 Tilt frame, end beam -
6 2 110293 Tilt frame, side beam -
7* 2 110298 . . Pivot pin, tilt frame -
8 2 110294 Tilt hanger -
9 1 110295 Upper yoke -
10 2 110296 Lower tilt hanger -
11 1 110297 Lower yoke -
12* 2 110324 . . Angle transducer pin -
13 1 110608 Trend and tilt sensor loom -
14 4 110491 Iglidur 20mm Ø x 11.5mm headed bush -
15 2 110492 Iglidur 12mm Ø x 15mm headed bush -
16 2 110493 Iglidur 10mm Ø x 15mm headed bush -
17 12 710183 M8 x 20mm cap head screw -
18 20 110631 M8 spring washer -
19 4 710186 M8 x 35mm cap head screw -
20 4 710189 M8 x 55mm cap head screw -
21 6 110950 M3 x 6mm Torx button head screw -
22 4 710434 M10 x 40mm cap head screw -
23 1 110387 Pedestal connector assembly -
24 2 710184 M8 x 25mm cap head screw -
25 2 110388 Top location angle -
26 2 110494 M6 x 10mm flanged oilite bush -
27 2 710153 M6 x 20mm cap head screw -
28 2 710151 M6 x 10mm cap head screw -
29 3 710215 M4 x 8mm cap head screw -
30 1 110607 Height potentiometer loom -
31 2 110538 Top actuator pin -
32 2 110539 Lower actuator pin -
33 8 713674 ‘R’ clip -
34 6 111208 Spacer, PCB -
35 1 710270 M5 x 10mm cap head screw -
36 1 710701 M5 plain washer -
37 2 711443 ‘P’ clip -
38 1 770242 ‘P’ clip -
39 4 110822 Bearing pad 4
40 3 110825 M16 bearing screw 3
41 1 111524 Four actuator PCA (see parts list 8) -
42# 1 111528 Connector block loom -
43 1 110590 Trendelenburg actuator assembly -
44 1 110591 Tilt actuator assembly -
45 1 110592 Tilt motor 1
46 1 111251 Trendelenburg motor 1
47 8 710431 M10 x 20mm cap hd screw -
48 12 710888 M10 spring washer -
49 4 111056 M4 x 10mm Cheese head nylon screw -
50 1 111057 4 Axis PCA insulation sheet -
* These parts are bonded to their mating parts (i.e. 5-7-12, 1-2-12, 5-7, 2-1) using retainer (part No. 670651).
# Not drawn
Note: For earth bonding see Parts List 8

T-IPL35h P11/26
PARTS LIST 4 - TRUNK SECTIONS

Fig. 5 Long trunk section assembly (see Fig 6 for short trunk assembly)

P12/26 T-IPL35h
 T20-a
OPERATION TABLE

PARTS LIST 4 - TRUNK SECTIONS

Item No. Qty. Part No. Description Spares

1* 2 110452 Side rail short trunk UK (also see section 1.8) -

2 8 110453 Black top location dowel 4
3 8 710263 M6 x 20mm hex skt csk hd screw st/st -
4* 1 110454 Black top short trunk -
5 28 709721 M8 x 16mm hex skt button head screw st/st -
6* 1 110455 Cover bottom short trunk left hand -
7 4 713674 ‘R’-clip, grip 10mm Ø wire 1.42mm Ø 2
8 2 110544 Ball bearing 8mm Ø 2
9 2 110666 Spring compression 7.62mm Ø x 25.4mm 2
10 2 110456 Plunger for push button 2
11 2 110457 Attachment block right hand -
12 8 110843 M8 x 80mm hex skt cap head screw st/st -
13 4 110458 Push button blade 2
14* 1 110542 Break gearbox assembly right hand (inc. motor) -
15* 1 110459 Cover bottom short trunk right hand -
16 4 699148 Rolled pin 3mm Ø x 12mm -
17 2 110460 Attachment block left hand -
18 4 110449 Spring compression 21.46mm Ø x 19.05mm 2
19 4 110461 Push button 2
20* 1 110462 Side arm short trunk right hand -
21 16 110951 M3 x 10mm Torx pin skt button head screw st/st 5
22 1 110463 Side arm long trunk right hand -
23 4 710242 M8 x 16mm hex skt csk head screw st/st -
24 6 700494 Dome plug, 12.7mm Ø 2
25 1 110464 Break attachment block right hand -
26 4 110950 M3 x 6mm Torx pin skt button head screw st/st -
27 2 110465 Traverse rod -
28 2 110466 Leadscrew traverse -
29* 1 110541 Break gearbox assembly left hand (inc. motor) -
30 1 110467 Break attachment block left hand -
31 1 110499 Traverse powered assembly (see Parts list 5) -
32 2 110546 M10 x 20mm hex skt set screw cup point -
33 1 110468 Side arm long trunk left hand -
34* 1 110469 Side arm short trunk left hand -
35 1 110470 Black top long trunk -
36 2 110471 Side rail long trunk UK (also see section 1.8) -
37 1 111044 Cover assembly long trunk (includes item 48) -
38 4 110498 Mattress retainer -
39 4 710265 M6 x 30mm hex skt csk head screw st/st -
40 4 742357 Screw cover 2
41* 1 110375 Cover short trunk -
42 4 110667 ‘P’-clip, 13mm rubber lined 2
43 4 710151 M6 x 10mm hex skt cap head screw st/st -
44 4 307159 M3 washer internal shakeproof -
45 2 710182 M8 x 16mm hex skt cap head screw st/st -
46* 2 110605 Break potentiometer loom (see Fig. 6) -
47* 2 110919 Valeo motor (see Fig. 6) -
48 4 111729 Eschmann T20a label (not supplied separately) -
49 4 709892 M3 x 16mm slotted csk head screw -
50* 2 709820 M8 x 12mm hex skt button head screw st/st -
* see Fig. 6
Note: For earth bonding see Parts List 8

T-IPL35h P13/26
PARTS LIST 4 - TRUNK SECTIONS

Note: On later tables the slot, in items 6 and 15,

has been modified to accept grommet strip (part
number 699769) to eliminate the possibility of
cables and conduit chaffing on the covers.

Fig. 6 Short trunk section assembly (see Fig 5 for long trunk assembly)

P14/26 T-IPL35h
 T20-a
OPERATION TABLE

PARTS LIST 4 - TRUNK SECTIONS

Item No. Qty. Part No. Description Spares

1 2 110452 Side rail short trunk UK (also see section 1.8) -

2 8 110453 Black top location dowel 4
3 8 710263 M6 x 20mm hex skt csk hd screw st/st -
4 1 110454 Black top short trunk -
5 28 709721 M8 x 16mm hex skt button head screw st/st -
6 1 110455 Cover bottom short trunk left hand -
7 4 713674 ‘R’-clip, grip 10mm Ø wire 1.42mm Ø 2
8 2 110544 Ball bearing 8mm Ø 2
9 2 110666 Spring compression 7.62mm Ø x 25.4mm 2
10 2 110456 Plunger for push button 2
11 2 110457 Attachment block right hand -
12 8 110843 M8 x 80mm hex skt cap head screw st/st -
13 4 110458 Push button blade 2
14 1 110542 Break gearbox assembly right hand (inc. motor) -
15 1 110459 Cover bottom short trunk right hand -
16 4 699148 Rolled pin 3mm Ø x 12mm -
17 2 110460 Attachment block left hand -
18 4 110449 Spring compression 21.46mm Ø x 19.05mm 2
19 4 110461 Push button 2
20 1 110462 Side arm short trunk right hand -
21 16 110951 M3 x 10mm Torx pin skt button head screw st/st 5
22* 1 110463 Side arm long trunk right hand -
23* 4 710242 M8 x 16mm hex skt csk head screw st/st -
24 6 700494 Dome plug, 12.7mm Ø 2
25* 1 110464 Break attachment block right hand -
26* 4 110950 M3 x 6mm Torx pin skt button head screw st/st -
27* 2 110465 Traverse rod -
28* 2 110466 Leadscrew traverse -
29 1 110541 Break gearbox assembly left hand (inc. motor) -
30* 1 110467 Break attachment block left hand -
31* 1 110499 Traverse powered assembly (see Parts list 5) -
32* 2 110546 M10 x 20mm hex skt set screw cup point -
33* 1 110468 Side arm long trunk left hand -
34 1 110469 Side arm short trunk left hand -
35* 1 110470 Black top long trunk -
36* 2 110471 Side rail long trunk UK (also see section 1.8) -
37* 1 111044 Cover assembly long trunk (includes item 48) -
38 4 110498 Mattress retainer -
39 4 710265 M6 x 30mm hex skt csk head screw st/st -
40 4 742357 Screw cover 2
41 1 110375 Cover short trunk -
42 4 110667 ‘P’-clip, 13mm rubber lined 2
43 4 710151 M6 x 10mm hex skt cap head screw st/st -
44* 4 307159 M3 washer internal shakeproof -
45* 2 710182 M8 x 16mm hex skt cap head screw st/st -
46 2 110605 Break potentiometer loom (see Fig. 6) -
47 2 110919 Valeo motor (see Fig. 6) -
48* 4 111729 Eschmann T20a label (not supplied separately) -
49* 4 709892 M3 x 16mm slotted csk head screw -
50 2 709820 M8 x 12mm hex skt button head screw st/st -
* see Fig. 5
Note: For earth bonding see Parts List 8

T-IPL35h P15/26
PARTS LIST 5 - POWERED TRAVERSE ASSEMBLY

Fig. 7 Powered traverse assembly

P16/26 T-IPL35h
 T20-a
OPERATION TABLE

PARTS LIST 5 - POWERED TRAVERSE ASSEMBLY

Item No. Qty. Part No. Description Spares

1 1 110394 Traverse crossbeam assy. fixed top -

2 2 700485 Dome plug 25.4mm Ø 1
3 10 710153 M6 x 20mm skt hd cap screw st/st -
4 2 110355 Pulley -
5 4 110525 Igus bearing -
6 4 110395 Traverse bearing housing -
7 4 709860 M3 washer plain st/st -
8 4 110951 M3 x 10mm Torx pin skt button hd screw st/st -
9 1 110396 Traverse motor assy. (see parts list 6) -
10 1 110397 Top connector assy. -
11 2 709863 M6 washer plain st/st -
12 1 110528 Belt 3mm pitch, 9mm wide, 1062mm long 1
13 4 110529 Ball bearing, id=17mm, od=40, w=12mm -
14 2 110438 Traverse nut -
15 2 110399 Traverse nut housing -
16 10 110952 M4 x 10mm Torx pin skt button hd screw st/st -
17 1 110400 Cover crossbeam top -
18 2 699148 Rolled pin 3mm x 12mm -
19 4 110401 Traverse limit switch pin -
20 2 111287 Traverse limit switch bracket -
21 4 111295 Spring compression od=6.1mm x 19.05mm -
22 2 110403 Traverse limit switch cam -
23 4 111294 Plastic headed bush -
24 4 714062 M3 x 5mm hex skt set screw st/st -
25 4 709991 M2.5 x 10mm slotted pan hd screw -
26 4 307240 M2.5 washer shake proof -
27 1 110603 Traverse motor loom with 2 microswitches -
28 1 110404 Cover crossbeam bottom -
29 4 695577 PCA support 4
30 1 111525 Three actuator PCA (see parts list 8) -
31 4 110533 M10 x 20mm hex head screw grade 8.8 -
32 2 111527 Break gearbox loom -
33 4 710888 Washer M10 spring st/st -
34 2 111296 Bearing preload wave washer -
35 2 110950 M3 x 6mm Torx pin skt button hd screw st/st -
36 2 711443 ‘P’-clip -
37# 1 111528 Connector block loom -
38 - 652809 Foam tape 180 x 10mm -
39 1 111058 Three actuator PCA insulation sheet -
# Not drawn
Note: For earth bonding see Parts List 8

T-IPL35h P17/26
PARTS LIST 6 - TRAVERSE MOTOR ASSEMBLY

Traverse motor plate

detail (for motor plates
introduced during 2003)

Fig. 8 Traverse motor assembly

P18/26 T-IPL35h
 T20-a
OPERATION TABLE

PARTS LIST 6 - TRAVERSE MOTOR ASSEMBLY

Item No. Qty. Part No. Description Spares

1 1 110536* Valeo motor (10mm nominal spindle) 1

or 111983* Valeo motor (12.8mm nominal spindle)
2 2 710875 M8 nut split locking -
3 1 710422 M5 x 16mm hex skt set screw -
4 1 110392* Pulley (10mm nominal bore) -
or 110722* Pulley (12.8mm nominal bore)
5 2 710703 M8 washer plain -
6 4 110818 Flange -
7 1 110880 Traverse motor plate -
8 2 110530 Needle bearing 10mm x 14mm x 15mm 2
9 3 110535 4mm x 12mm screw pozi pan head -
10 2 710153 M6 x 20mm skt head cap screw st/st -
11 2 110881 Traverse motor plate support -
12 2 110819 Shoulder screw M8 non-standard -

* Note: Ensure Motor and pulley size match

T-IPL35h P19/26
PARTS LIST 7a - BASE ASSEMBLY (Tables with SN T2AA....)

Fig. 9 Base assembly

P20/26 T-IPL35h
 T20-a
OPERATION TABLE

PARTS LIST 7a - BASE ASSEMBLY (Tables with SN T2AA....)

Item No. Qty. Part No. Description Spares

1 1 110259 Base plate -

2 1 110445 Column assembly -
3 4 710434 M10 x 40mm cap hd screw -
4 2 110272 Brake pad 2
5 2 710152 M6 x 35mm cap hd screw -
6 2 110378 Front wheel assembly comprising -
(2) 110267 . Front wheel carrier -
(2) 110407 . Front wheel 1
(2) 710189 . M8 x 55mm cap hd screw -
7 4 710184 M8 x 25mm cap hd screw -
8 4 110260 Castor pillar -
9 4 710185 M8 x 30mm cap hd screw -
10 - - Not fitted, no longer required -
11 4 110271 Castor pillar spacer -
12 1 110261 Castor plate front -
13 1 110262 Castor plate rear -
14 5 110263 Pedal anchor block -
15 5 110446 Iglidur headed bush -
16 10 110486 M8 x 90mm cap hd screw -
17 1 111465 Mains panel/loom assembly -
18 1 110265 Front pedal spindle assembly -
19 1 699148 M3 x 12mm roll pin -
20 1 110269 Lifting wheel axle front -
21 1 110275 Brake pedal front (castor) -
22 1 110264 Rear pedal spindle assembly -
23 1 110273 Lifting wheel axle rear -
24 4 710919 M10 washer st/st -
25 2 110270 Lifting wheel assembly 1
26 2 110447 Spring compression 7.62Ø x 9.53mm 1
27 2 110450 M8 x 10mm x 16mm hex skt hd shoulder screw -
28 1 110274 Brake pedal rear (wheel) -
29 1 110279 Damper angle bracket rear -
30 2 110451 Damper 1
31 4 710182 M8 x 16mm cap hd screw -
32 2 710270 M5 x 10mm cap hd screw -
33 2 110266 Catch block -
34 4 700083 M6 x 16mm cap hd screw -
35 PAIR 110277 Pedal anti-skid pads (1-left & 1-right hand) 1
36 1 110942 Resistor assy (static discharge) -
37 2 710731 M4 int shakeproof st/st washer -
38 1 710839 M4 hex st/st nut -
39 2 710555 M3 x 25mm button hd st/st screw -
40 1 710211 M4 x 10mm cap hd screw -
41 2 710702 M6 st/st plain washer -
42 4 110446 Iglidur headed bush -
43 4 713524 Castor insulation pad -
44 1 110895 Battery support plate -
45 16 713523 Isolating bush -
46 16 713538 Special washer -
47 16 710414 M6 x 30mm hex hd set bolt -
48 1 713522 Connector -
49 4 110895 Castor assembly (includes wheels) 2
50 (8) 110900 . Wheel assembly 4
51 1 111738 Damper angle bracket front -
# 2 111248 Castor earthing lead -
T-IPL35h P21/26
PARTS LIST 7b - BASE ASSEMBLY (Tables with SN T2AC.... or later)

Assembly notes:
1. Apply threadlock (670650) to all threads.
2. Items 3 should be tightened to 40nm (29.5 lb/ft).
3. Apply grease (670160) to the sliding surfaces of the castor pillars, the internal surfaces of all headed
bushes, and the damper pivot points.
4. The disc springs (item 15) should be positioned against each other so that there is a hollow space
between them.
5. Shim(s) (item 40) only fitted if required on final assembly to obtain correct pedal adjustment.

P22/26 T-IPL35h
 T20-a
OPERATION TABLE

PARTS LIST 7b - BASE ASSEMBLY (Tables with SN T2AC.... or later)

Item No. Qty. Part No. Description Spares

1 1 110259 Base plate -

2 1 110445 Column assembly -
3 4 710434 M10 x 40mm cap hd screw -
4 2 110272 Brake pad 2
5 2 710152 M6 x 35mm cap hd screw -
6 2 110378 Front wheel assembly (see Parts List 7c) -
7 4 710184 M8 x 25mm cap hd screw -
8 4 110260 Castor pillar -
9 4 710185 M8 x 30mm cap hd screw -
10 2 111454 Catch assembly (see Parts List 7c) -
11 6 710154 M6 x 25mm cap hd screw -
12 1 110895 Standby battery tray -
13 2 111490 Front castor plate spacer -
14 4 111488 M20 plain washer s/s form B -
15 4 111489 Disc spring -
16 1 111484 Rear castor plate assy (see Parts List 7c) -
17 1 111485 Front castor plate assy (see Parts List 7c) -
18 1 110942 Static discharge resistor assembly -
19 2 710555 M3 x 25mm cap hd screw -
20 1 111429 Rear damper anchor bracket -
21 1 111738 Front damper bracket -
22 2 710182 M8 x 16mm cap hd screw -
23 2 110451 Damper 1
24 1 111459 Damper clevis pin* -
25 1 710200 M4 x 8mm grub screw* -
26 5 110263 Pedal anchor block -
27 10 110486 M8 x 90mm cap head screw -
28 5 110446 Headed bush -
29 1 112097 Rear pedal spindle assy (see Parts List 7c) -
30 1 112098 Front pedal spindle assy (see Parts List 7c) -
31 1 111816 Rear pedal shaft spacer -
32 1 111487 Front pedal shaft thrust ring -
33 1 112164 Rear pedal -
34 1 112165 Front pedal -
35 2 710261 M6 x 16mm c/snk screw -
36 1 110277 Pair of pedal anti-slip inserts 1
37 2 742357 Screw cover -
38 1 710839 M4 nut -
39 2 710731 M4 shakeproof washer -
40 as reqd. 111875 Front castor plate shim -
* or use standard clip supplied as part of damper 110451
T-IPL35h P23/26
PARTS LIST 7c - BASE ASSEMBLY (Tables with SN T2AC.... or later)

P24/26 T-IPL35h
 T20-a
OPERATION TABLE

PARTS LIST 7c - BASE ASSEMBLY (Tables with SN T2AC.... or later)

Item No. Qty. Part No. Description Spares

111484 / 111485 (quantity below is for each assembly)
1 1 111427 Castor plate rear -
2 2 110446 Headed bush -
3 2 713524 Castor insulation pad -
4 1 713522 Connector, static discharge -
5 2 699848 Castor (see note 4) -
6 8 713523 Isolating bush -
7 8 713538 Special washer -
8 8 710414 Hex. hd. set bolt (see note 2) -
9* 2 111949 Screw Hex. hd. M10 x 50mm -
10 2 710845 M10 nut -
11 1 111449 Castor plate front -
Assembly notes for 111484 / 111485:-
1. Use threadlock (670650) on all threads apart from items 9 & 10.
2. Tighten bolts (items 8) to 2.8Nm (25lbf.in) overtightening can compromise insulation properties of item 3.
3. Socket (item 9) to face upwards and nut (item 10) to lock against underside of castor plate (item 1).
4. Castor wheels (110900) and washers (710704) can be replaced if required rather than
the whole castor assembly. Use 2 wheels and 3 washers per castor assembly.
* Item 9 was 699775 (Socket set screw), Hex head screw (111949) now preferred.
110378 Front wheel assembly
1 1 110267 Front wheel carrier -
2 1 110407 Front wheel -
3 1 710189 M8 x 55mm cap hd. screw -
111454 Catch assembly
1 1 111435 Catch block -
2 1 111436 Catch pawl -
3 1 699200 M8 x 50mm dowel pin -
4 2 704532 8mm starlock washer -
5 1 699147 M3 x 20mm selock pin -
6 1 111461 Spring -
Assembly notes for 111454:
1. Item 2 to rotate freely on item 3.
2. End of item 5 to be flush with inside edge of the short leg of item 1.
112098 Front pedal spindle assembly
1 1 111673 Front pedal spindle -
2 1 110269 Lifting wheel axle front -
3* 2 110408 Needle roller bearing -
4 1 110479 Lifting wheel spacer -
5* 2 710919 M10 washer s/s -
112097 Rear Pedal spindle assembly
1 1 111672 Rear pedal spindle -
2 1 111432 Rear lifting wheel axle -
3 1 710200 M4 x 8 soc. hd. grub screw -
4* 2 110408 Needle roller bearing -
5 1 111433 Rear lifting wheel spacer -
6* 2 710919 M10 washer s/s -
* Not illustrated position only indicated.
Assembly notes for 112098 and 112097:
1. Assemble ‘Bearing’ to ‘Lifting wheel spacer’ with retainer (110877).
2. Apply grease (110477) to ‘Needle roller bearing’ during assembly.

T-IPL35h P25/26
PARTS LIST 8 - MAIN ELECTRICAL COMPONENTS

PCA / Loom Part No. Qty. Shown on

Pedestal connector assembly 110387 1 Parts list 3, item 23

Top connector assembly 110397 1 Parts list 5, item 10
Three actuator PCA 111525 1 Parts list 5, item 30
consisting of:
3 Actuator PCA 111483 1
Processor PCA 111526 1
Mains indicator (panel) loom 111465 1 Parts list 2, item 33
Switch panel loom 110597 1 Parts list 2, item 12
Handset panel loom 111577 1 Parts list 2, item 11
Connector block loom 111528 1 Parts list 3, item 42
Connector block loom 111609 1 Parts list 5, item 37
Column energy chain loom 111463 1 Parts list 2, item 25
Traverse motor loom (inc. m’switches) 110603 1 Parts list 5, item 27
Break gearbox loom 111527 2 Parts list 5, item 32
Break potentiometer loom 110605 2 Parts list 4, item 46
Height potentiometer loom 110607 1 Parts list 3, item 30
Trend and Tilt sensor loom 110608 1 Parts list 3, item 13
Power supply assembly 111765 1 see ‘Note 1’ below
Battery charger modules - 1 see section 1.9
Battery management PCA - 1 see ‘Note 1’ below
Infrared receiver PCA 110729 2 see ‘Note 2’ below
Four actuator PCA 111524 1 Parts list 3, item 41
consisting of:
4 Actuator PCA 111482 1
Processor PCA 111526 2
Standby panel 111499 1 Parts list 2, item 32
Batteries - - See section 1.9
Fuses - - See section 1.10
Earth Bonding:
Tilt/Trend frame - 111418 Column - 111463 Tilt frame/Column - 111419
Tilt motor - 111418 Trend motor - 111420 Castor plate - 111743
Column cover - 111744
Note 1.
111765 (Power supply assembly, Parts list 2, item 28) which is located in the table base includes, a Battery charger
loom, a Battery charger module, a Battery management PCA, a Battery connector loom, a Chassis plate, two Battery
support brackets, a Switch, two Fuses (32 x 6.35mm 20A ‘T’ type), two Fuse holders, two battery pairs and all connections,
cable ties and screws etc. This (111765) must be changed inaccordance with the instructions given in the service
manual.
Note 2.
These PCAs (110729, Infrared receivers) are fitted one to each base cover (items 1 and 2, Parts list 2) with two plastic
rivets (part number 110698).

P26/26 T-IPL35h
Eschmann Equipment, Peter Road, Lancing, West Sussex, BN15 8TJ, England.
Tel: +44 (0) 1903 753322. Fax: +44 (0) 1903 766793. www.eschmann.co.uk