Operating Instructions: Parallel Shaft Helical Gearboxes

OPERATING
INSTRUCTIONS
D Series
Parallel Shaft Helical Gearboxes
OIDCE0300-0418
Operating Instructions
D Series
Contents
Contents
1- How To Use This Manual.......................................................................................... 04
2- Unit Designation....................................................................................................... 05
2.1 Detailed unit designation...................................................................................... 05
2.2 Nameplate unit designation................................................................................. 06
3- Part List of Standard Type Gear Units.................................................................... 07

3.1 D...00... Type........................................................................................................ 07
3.2 D...01... Type........................................................................................................ 08
3.3 D...02... Type........................................................................................................ 19
3.4 D...03... Type........................................................................................................ 10
3.5 D...0S...Type........................................................................................................ 11
3.6 D...0E... Types..................................................................................................... 12
3.7 D..4 Additional Stage........................................................................................... 13
3.8 D..5 and D..6 Additional Stages........................................................................... 15
3.9 D Series Motor Flange for Direct Coupled Types................................................ 15
3.10 DN..., DV...Types B5, B14 Motor Flange............................................................ 15
3.11 DT... Types Input Bearing Housing with Solid Input Shaft.................................. 16
4- Safety......................................................................................................................... 17
4.1 Intended Use........................................................................................................ 17
4.2 Improper Use....................................................................................................... 17
4.3 Safety Instructions............................................................................................... 18
4.3.1 General Safety Instructions.................................................................... 18
4.3.1.1 Working on the gear reducer....................................................... 18
4.3.1.2 Operation.................................................................................... 18
4.3.1.3 Maintenance............................................................................... 18
4.3.1.4 Lubricant.................................................................................... 18
4.3.1.5 Ambient Conditions.................................................................... 18
4.4 Tightening Torques............................................................................................. 19
4.5 Case of Fire....................................................................................................... 19
4.5.1 Suitable extinguishing agents, protective equipment.......................... 19
4.5.2 Unsuitable extinguishing agents......................................................... 19
5- Thinks to Check Before the Gear Unit or Geared Motor is Installed................... 20

5.1 Transportation.................................................................................................. 20
5.2 Storage............................................................................................................ 21
6- Installing The Gear Unit........................................................................................... 21

6.1 Before you start.................................................................................................... 21
6.2 Check the shaft dimensions to fit......................................................................... 22
6.3 Check the ambient temperature........................................................................... 22
6.4 Check the voltage supply..................................................................................... 22
6.5 Check the mounting position................................................................................ 25
6.6 Use the breather plug.......................................................................................... 25
6.7 Check the oil level................................................................................................ 25
6.8 Check shaft ends and mounting faces................................................................. 25
6.9 Cover abrasive ambient....................................................................................... 25
6.10 Check accessibility to filling, breather and drain plugs...................................... 26
2
D Series
Contents
7- Mechanical Installation............................................................................................ 26
7.1 Installing customer shaft with shoulder............................................................... 27
7.2 Installing customer shaft without shoulder.......................................................... 28
7.3 Disassembling customer shaft with shoulder..................................................... 29
7.4 Disassembling customer shaft without shoulder............................................... 30
7.5 Shaft tightening torques...................................................................................... 31
7.6 Recommended shaft dimensions and disassembling nut dimensions................ 32
7.7 Dimensions of Splined Hollow Shaft to DIN 5480............................................... 33
7.8 Assembling customer shaft with shrink disk...................................................... 34
7.9 Disassembling customer shaft with shrink disk.................................................. 36
7.10 Assembling gear unit with torque arm.............................................................. 37
7.11 Fitting output shaft elements............................................................................. 40
7.12 Correct position of output shaft elements....................................................... 40
7.13 Fitting couplings................................................................................................. 41
8- Maintenance & Inspection....................................................................................... 42
9- Lubrication................................................................................................................ 43
9.1 Oil types............................................................................................................... 43
9.2 Changing the oil................................................................................................... 44
9.3 Mounting Positions............................................................................................... 45
9.4 Oil Quantities....................................................................................................... 46
10- Troubleshooting Guide.......................................................................................... 49
11- Disposal.................................................................................................................. 52
11.1 Disposal of oil.................................................................................................... 52
11.2 Disposal of sealing............................................................................................ 52
11.3 Disposal of metal............................................................................................... 52
12- Appendix................................................................................................................. 53
12.2 Warranty conditions.......................................................................................... 54
12.3 Warranty............................................................................................................ 55
3
D Series
General Informations
1- How To Use This Manual
Take attention to the following safety and warning signs for proper understanding and quick reference.
Electric Hazard; Can cause severe or fatal injuries.
Mechanical Hazard; Can cause severe or fatal injuries.
Likely to be Hazardous; Can cause minor or fatal injuries.
Damage Risk; Can damage gearbox or environment.
Important Information.
EC Machinery Directive:
Within terms of the EC machinery directive 2006/42/EC, the gearboxes are considered
as not autonomous machine, but as a component to install in machines.
Operation is prohibited within the area of validity of the EC directive, until it has been
determined that the machine, in which this product is installed, corresponds to the regula-
tions within this directive.
The operating instructions contain important information to ensure;

- Trouble-free operation
- Fulfilment of any rights to claim under guarantee
The operating instruction must be kept close to the gearbox and must be available in
case it is needed.
This operating instruction is written for D series gear units and is applicable only for D
series. If any different type of gearbox is used please ask YILMAZ REDUKTOR for the
operating instructions of that type.
This instruction can be used only for standard type geared units of YILMAZ REDUKTOR.
For special application and modified gear units ask YILMAZ REDUKTOR for validity.
This manual does not cover 94/9/EC compatible gearboxes. For 94/9/EC contact YILMAZ
REDUKTOR.
4
D Series
Type Designation
2- Unit Designation
2.1- Detailed unit designation
Detailed D series gear units designation for ordering
(This Designation is different from the short nameplate designation)
D R 4 7 4 .02 3 E90S / 4C - L02
Brake
L-220V With Fan
P-24V With Fan
S-220 V Without Fan
Z-24 V Without Fan
01-10 Nm 10-100 Nm
02-25 Nm 20-200 Nm
04-40 Nm 30-300 Nm
05-50 Nm 40-400 Nm
Number of poles
Motor Size For DN Types

For DR / DV /Types A06 :63 B5 A09 : 90 B5 A13:132 B5 A25: 250 B5
E90S / 4 B06 :63 B14 B09 : 90 B14 B13:132 B14 A28: 280 B5
A07 :71 B5 A10 :100 B5 A16:160 B5 A31: 315 B5
B07 :71 B14 B10 :100 B14 A18:180 B5
Pole Number
A08 :80 B5 A11 :112 B5 A20:200 B5
Frame Lenght B08 :80 B14 B11 :112 B14 A22:225 B5
Motor size
Motor type
Motor Efficiency Class
Output Shaft
00 :Hollow Shaft output
01 :Solid Shaft Output
02 :Solid shaft output with IEC B5 /14 Flange
03 :Flanged and Hollow Shaft output
0S :Shrink Disk Output
0E :Extruder Output
Stage
2 Stages
3 Stages 5 Stages
4 Stages 6 Stages
Revision Number
Housing Size
1...9
Input Type
R :With Motor
N :IEC B5 / B14 Flanged without Motor
V :IEC B5 / B14 Flanged with Motor
T :Without Motor
Gearbox Type
D Serie
5
D Series
Type Designation
2.2- Nameplate, unit designation
Nameplate unit designation is a short abbreviation from the detailed designation
A sample name plate for D Series
YILMAZ REDÜKTÖR
www.yr.com.tr
MADE IN TURKEY
Type : DR473.03-90L/4
Serial N.: 100524545
Power : 1.5 kW Ratio: 121,49
Speed: 12 rpm. M. Pos.: M1
Oil: ISO VG320
(Mineral Oil)
Oil Qty : 6.4 lt.
Abreviations:
Serial N. : Serial Number
M.Pos. : Mounting Position
Type Designation;
DR473 - 3E71M/4C
Type Motor Size
DR- With motor

DT- With input shaft
DV- With Motor and IEC Flange
DN- IEC Flange without Motor
6
D Series
Part Designation
3- Part List of Standard Type Gear Units

3.1- D..00... Types for 2 and 3 Staged Gear Units
3
3
Only Valid For 3 Stages
31 1
29
30
32
33 24 2
34
35 28
27
26
25 3
23
22 11
4
21 5
20 6 3
19
18 7
8
9
10
12
13
14
15
16
17
Standard D...00... type basic part diagram. Parts may differ for special applications.
Standard Part List
1- Pin Screw 9- Bearing 17- Seal 25- Gear 33- Bearing
2- Housing 10- Hollow Shaft 18- Closing Cap 26- Spacer 34- Circlip
3- Plug 11- Key 19- Circlip 27- Bearing 35- Closing Cap
4- Cover Plate 12- Gear 20- Spacer 28- Spacer
5- Screw 13- Spacer 21- Spacer 29- Bearing
6- Oil Seal 14- Bearing 22- Bearing 30- Gear
7- Circlip 15- Spacer 23- Shaft Gear 31- Key
8- Spacer 16- Circlip 24- Key 32- Gear
7
D Series
Part Designation
3.2- D..01... Types for 2 and 3 Staged Gear Units

3
3
Only Valid For 3 Stages 1

32
30
31
33
34 25 2
35
36 29
28
27
26 3
24
23 11
4
22 5
21 12 6 3
20
19 7
8
9
10
13
14
15
16
17
18
Standard Part List
1- Pin Screw 9- Bearing 17- Circlip 25- Key 33- Shaft Gear
2- Housing 10- Output Shaft 18- Oil Seal 26- Gear 34- Bearing
3- Plug 11- Key 19- Closing Cap 27- Spacer 35- Circlip
4- Cover Plate 12- Key 20- Circlip 28- Bearing 36- Closing Cap
5- Bolt 13- Gear 21- Spacer 29- Spacer
6- Oil Seal 14- Spacer 22- Spacer 30- Bearing
7- Circlip 15- Bearing 23- Bearing 31- Gear
8- Bearing 16- Spacer 24- Shaft Gear 32- Key
8
D Series
Part Designation
3.3- D..02... Types For 2 and 3 Staged Gear Units

3
3
34 1
32
33
35
36 27 2
37
38 31
30
29
28 3
26
25 11
4
24 5
23 12 3
22
21 6
7
8
9
10
13
14
15
16
17
18
19
20
Standard Part List
1- Pin Screw 10- Solid Shaft 19- Flange 28- Gear 37- Circlips
2- Housing 11- Key 20- Bolt 29- Spacer 38- Closing Cap
3- Plug 12- Key 21- Closing Cap 30- Bearing
4- Cover Plate 13- Gear 22- Circlip 31- Spacer
5- Bolt 14- Spacer 23- Spacer 32- Bearing
6- Oil Seal 15- Bearing 24- Spacer 33- Gear
7- Circlip 16- Spacer 25- Bearing 34- Key
8- Spacer 17- Circlip 26- Shaft Gear 35- Shaft Gear
9- Bearing 18- Seal 27- Key 36- Bearing
9
D Series
Part Designation
3.4- D..03... Types For 2 and 3 Staged Gear Units 3

3
33 1
31
32
34
35 26 2
36
37 30
29
28
27 3
25
24 11
4
23 5
22 3
21
20 6
7
8
9
10
12
13
14
15
16
17
18
19
Standard Part List
1- Pin Screw 9- Bearing 17- Oil Seal 25- Shaft Gear 33- Key
10- Hollow
2- Housing 18- Flange 26- Key 34- Gear
Output Shaft
3- Plug 11- Key 19- Bolt 27- Gear 35- Bearing
20- Closing
4- Cover Plate 12- Gear 28- Spacer 36- Circlip
Cap
37- Closing
5- Bolt 13- Spacer 21- Circlip 29- Bearing
Cap
6- Oil Seal 14- Bearing 22- Spacer 30- Spacer
7- Circlip 15- Spacer 23- Spacer 31- Bearing
8- Spacer 16- Circlip 24- Bearing 32- Gear
10
D Series
Part Designation
3.5- D...0S... Types For 2 and 3 Staged Gear Units

4
4
32 1
30
31
33 2
34 25
35 3
36 29
28
27
26 4
24
23 12
5
22 6
21 7 4
20
19 8
9
10
11
13
14
15
16
17
18
Standard D...0S... type basic part diagram. Parts may differ for special applications.
Standard Part List
1- Pin Screw 9- Spacer 17- Circlip 25- Key 33- Shaft Gear
2- Shrink Disk 10- Bearing 18- Oil Seal 26- Gear 34- Bearing
3- Housing 11- Output shaft 19- Closing Cap 27- Spacer 35- Circlip
4- Plug 12- Key 20- Circlip 28- Bearing 36- Closing Cap
5- Cover Plate 13- Gear 21- Spacer 29- Spacer
6- Bolt 14- Spacer 22- Spacer 30- Bearing
7- Oil Seal 15- Bearing 23- Bearing 31- Gear
8- Circlip 16- Spacer 24- Shaft Gear 32- Key
11
D Series
Part Designation
3.6- D...0E... Types For 3 Staged Gear Units
1
2
9 3
9 4
5
6
7
8
10
11
12
Standard D...0E... type basic part diagram. Parts may differ for special applications.
Standard Part List
1- Circlip 5- Extruder Neck 9- Key
2- Spacer 6- Bolt 10- Hollow Shaft Output
3- Flange 7- Seal 11- Spacer
4- Bolt 8- Bearing 12- Seal
12
D Series
Part Designation
3.7- D..4 Series Additional Stage for 4 Stage Types
15
4
14
13
1
2
3
4
12
11
5
6
7
8
9
10
Standard D..4 type additional stage basic part diagram. Parts may differ for special
applications.
Parts List
1- Circlips 6- Circlips 11- Key
2- Bearing 7- Shaft 12- Key

3- Gear 8- Seal 13- Bolt
4- Oil plug 9- Gear 14- Additional Housing
5- Bearing 10- Circlips 15- Screw Pin
13
D Series
Part Designation
3.8- D Series 5-6 Stages Types
N Type 2 and 3 stages are additional housing of D series 5 stages and 6 stages of gear
units.
34 35
36
37
33
38
29
32
31
30
28
27
26 24
25 23
17 22
1
15 2
21 8
3
20 4
19 5
18 6
14
16 7
9
10
11
12
13
Standard N type 3 stages basic part diagram. Parts may differ for special applications.
Parts List
1- Housing 9- Gear 17- Key 25- Cover 33- Oil plug
2- Oil plug 10- Bearing 18- Seal 26- Circlips 34- Bolt
3- Circlips 11- Circlips 19- Circlips 27- Bearing 35- Eye bolt
4- Bearing 12- Cover 20- Bearing 28- Gear 36- Oil plug
5- Spacer 13- Output Flange 21- Spacer 29- Key 37- Top side cover
6- Gear 14- Bolt 22- Gear 30- Gear 38- Screw Pin
7- Bearing 15- Key 23- Bearing 31- Bearing
8- Key 16- Output Shaft 24- Circlips 32- Circlips
14
D Series
Part Designation
3.9- D Series Motor Flange for Direct Coupled Types
10
Parts List 9
1- Shaft 6- Key
1
2- Circlips 7- Gear
2
3- Bearing 8- Circlips 3
4
4- Circlips 9- Nut
5- Flange 10- Key 5

6
7
8
3.10- DN..., DV...Types B5, B14 Motor Flange
10
Parts List 9
1
1- Shaft 6- Seal
2
2- Circlips 7- Gear 3
4
3- Bearing 8- Circlips
4- Circlips 9- Nut
5- B5 / B14 Flange 10- Key 6 5

7
8
15
D Series
Part Designation
3.11- DT... Types Input Bearing Housing with Solid Input Shaft
Parts List
11 1
1- Seal 7- Circlips 10
2
2- Nut 8- Gear 3
4
3- Flange 9- Circlips
4- Shaft 10- Key
5
5- Bearing 11- Key 6
7
6- Bearing 8
9
16
D Series
Safety
4- Safety
4.1- Intended Use

The gear reducer is designed for use in industrial machines. Please refer to our catalogue
or our web page for the maximum permitted torques and speeds. The most important maxi-
mum permitted values are indicated on the nameplate of the product. But the whole data
can be found on our product catalogues. Using the product out of the product catalogue /
nameplate’s permitted ranges will cancel the warranty/manufacturer declaration and YILMAZ
will not take any responsibility.
The gear units are intended for industrial machines and may only be used in accordance
with the information provided in this manual the product catalogue and the nameplate of
the gearbox. They comply with the applicable standards and regulations and meet the
requirements of the directive 2006/42/EC. The gearbox must be started up, maintained
and operated according this manual. The gearbox most be incorporated with 2006/42/EC
confirming parts/machines.
A motor connected to the gear unit is only allowed to be operated in the frequency entries
so that the data provided on nameplate/catalogue of the gear unit is not exceeded and is ac-
cordance with the nameplate/catalogue. The speed range will be provided on the name plate
if YILMAZ REDUKTOR is informed that the gear unit will be used with frequency inverter.
If not informed the nameplate will have a single fixed speed and only this speed is allowed.
The electric motor and frequency inverter must be in accordance with 2006/42/EC.
If the gear units input is used with variable speed gear unit, this must be informed to YILMAZ
REDUKTOR before ordering and on the nameplate the allowed maximum and minimum
speeds (speed range) will be provided. If not mentioned by ordering the gear units speed
will be a fixed single input speed and only this speed is allowed.
If the gear unit will be driven by belt / coupling / chain drive etc. the gear unit is only allowed
to be used according the nameplate/catalogue entries. Different speed, higher motor power,
higher radial/axial loads etc. than nameplate/catalogue is not allowed.
The ambient temperature must be between +5 - +40 ºC and no abrasive media must attack
the paint and seals. If different working conditions this must be informed to YILMAZ before
ordering.
The gearbox maintenance (oil change / check ) must be done according this manual.
4.2- Improper Use

Every usage which exceeds the limits stated above, the nameplate and catalogue of the
product (especially higher torques and speeds) is not compliant with the regulations, and
thus prohibited.
The operation of the gear reducer is prohibited if;
-It was not mounted/installed according to regulations and this manual
-The gear reducer is very soiled
-It is operated without lubricant
-It is operated out of the permitted values provided on catalogues and/or nameplate.
17
D Series
Safety
4.3- Safety Instructions
4.3.1- General Safety Instructions
4.3.1.1- Working on the gear reducer

- Inappropriately executed work can lead to injury or damage.
Make sure that the gear reducer is only installed, maintained and dismantled by trained
technicians.
- Foreign bodies spinning through the air can cause grave injury.
Before putting the gear reducer into operation, check that there are no foreign bodies or
tools near the gear reducer
4.3.1.2- Operation
- Touching hot surfaces can lead to burns.
Do not touch the gear reducer if their operation temperatures are too high, or use suitable
safety equipment like gloves.
-Rotating machinery can lead to injuries. There is danger of being trapped or pulled in!
Keep a sufficient distance and make safeguarding to rotating machinery. See relevant norms
EN349+A1, EN13857.
4.3.1.3- Maintenance
-An unintentional start of the machine during maintenance work can lead to serious accidents.
Make sure no one can start the machine while you are working on it.
- Even a brief running of the machine during maintenance work can lead to accidents if the
safety devices are not operating.
Make sure that all safety devices are mounted and active.
4.3.1.4- Lubricant
- Extended, intensive contact with oils can lead to skin irritations.
Avoid extended contact with oil, and clean oil off skin thoroughly.
- Hot oil can cause scalding.

When changing oil, protect yourself against contacting hot oil.
4.3.1.5- Ambient Conditions

- Standard gearboxes are allowed to work in ambient temperatures between +5 to +40ºC
unless differently specified on the nameplate. Using the gear unit out of this range can cause
damage to the gear unit or environment. Over +40 ºC ambient conditions the gear unit sur-
face temp could be so high causing burns when touched.
-If the gear unit will be used in outdoor applications the gear unit must be prevented from
rain snow and dust. Entering substances inside the gear unit from seals can damage the
gear unit. Observe the safety instructions for outdoor use EN12100:2010.
18
D Series
Safety
4.4- Tightening Torques

All screwed connections for which a tightening torque is specified, must on principle be
tightened with a calibrated torque wrench and checked. Use the following torques for the
threaded bores over the gear unit housing. For connecting elements refer to the mechani-
cal installation part.
Bolt Tightenning
Class
Size Torque [Nm]
M8 8.8 23
M10 8.8 43
M12 8.8 77
M16 8.8 190
M20 8.8 370
M24 8.8 640
4.5- Case of Fire

The gear reducer itself is not combustible. However, it usually contains a synthetic or min-
eral gear oil.
Please observe the following if the gear reducer is situated in a burning environment
4.5.1- Suitable extinguishing agents, Protective equipment

Always keep suitable extinguishing, protective equipment like carbon dioxide, powder, foam,
fog easily accessible around the gear unit.
-High temperature produce irritating steam.

Use a protective breathing apparatuses.
4.5.2- Unsuitable extinguishing agents

Do not spray with water!
19
D Series
Safety
5- Thinks to Check Before the Gear Unit or Geared Motor is Installed
If geared motors are used, please also refer to the manual of the motor manufacturer.
Before you install the gearbox you have to be sure that the gearbox is arrived with the all necessary
equipment and without damage. Points to take into consideration before you start to install the unit;
- You have received the correct operation manual of the your product.
- The gearbox and all its parts are transported without damage.
- The gearbox is stored correctly according the instructions in this manual
-You have the latest product catalogue or you have access to our web page
5.1- Transportation
When the goods arrive, first check for any damage. If some damage observed, immediately contact
the transport company and inform about the damage. Contact YILMAZ for the damage and do not
start to install the unit until it is agreed that the damage has no affect of operation.
Use the supplied eyebolts or lifting holes for lifting up the gear unit. The eyebolts are capable to
carry the weight of gearboxes only. Do not hang additional loads. Use suitable hoisting equipment
which is capable to hold the gear units weight. Refer to the catalogue for various types weights. See
drawing bellow for hoisting point.
Do not stay beneath / under the lifting/hoisting equipment which may cause serious injuries by falling
down objects, accidental movements, unexpected accidents.
Falling or hard placement can damage the gear unit.

Only use hoisting and securing equipment which is permitted for the size / weight of your gear unit.
Ensure that the load is slowly and carefully handled and placed.
20
D Series
Checking
5.2- Storage
If the geared unit or geared motor will be stored up to 3 years refer to the following in-
structions;
With Packing;
-Use corrosion protection oil for the output shaft and connection surfaces like flange sur-
face or foot assembling surface. Seal the unit in a plastic wrap and pack it in container.
A moisture indicator should be placed around the container to observe the moisture.
Relative atmospheric humidity should not exceed 50%. The container should be kept
under roof which protects from snow and rain. Under this condition the gear unit can be
stored up to 3 year with regular check. The ambient temperature should be between -5
to 60 ºC.

Without Packing;
-Use protection oil for the output shaft and connection surfaces like flange surface or
foot assembling surface. If no packing is used and the gearbox is stored without pack-
ing, the ambient temperature should be between 5 to 60 ºC. The gearbox must be kept
under enclosed roof with constant temperature and constant humidity not exceeding
50%. The storage should be free of dust and dirt and ventilated with filter. If the gearbox
is stored without packing it is recommended not to store more than 2 years and regular
check during this time is recommended.
If stored in open protect against insect damage.
6- Installing The Gear Unit
6.1- Before you start;

- Observe the gear unit for damages of storage or transportation. If any damage please
contact YILMAZ REDUKTOR.
- Be sure that you have all the equipment necessary for installing like; Spanners, torque
wrench, shims and distance rings, fixing devices for input and output elements, lubricant,
bolt adhesive etc.
- This manual is not for 94/9/EC (ATEX) conforming gear units. For 94/9/EC conforming
gear units refer to the ATEX range manual. ATEX conforming gear units have name
plates indicating the zone and the temperature class and are different from standard
type geared units. Therefore Standard units can not be installed on Potentially explosive
atmospheres.
21
D Series
Checking
6.2- Check the shaft dimensions to fit;
Output Shaft Centering

Flange
Hollow Shaft Hollow Shaft Output Shaft Tolerance (DIN748) Shoulder
Type Centering Shoulder
Diameter Tolerance (H8) Diameter Up to 50mm k6 Tolerance
Diameter
Over 50mm m6 ( g6 )
+0.02 +0.02 -0,01

D...072/073... 25 25 80
0 0 -0,03
+0.02 +0.02 -0,01
D...172/173... 30 30 80
0 0 -0,03
+0.03 +0.02 -0,01
D...272/273... 35 35 86
0 0 -0,03
+0.03 +0.02 -0,01
D...282/283... 40 40 110
0 0 -0,03
+0.03 +0.02 -0,01
D...372/373... 40 40 110
0 0 -0,03
+0.03 +0.02 -0,01
D...472/473... 50 50 130
0 0 -0,03
+0.03 +0.03 -0,01
D...572/573... 60 60 180
0 +0.01 -0,03
+0.03 +0.03 -0,01
D...672/673... 70 70 180
0 +0.01 -0,03
+0.04 +0.03 -0,01
D...772/773... 90 90 230
0 +0.01 -0,03
+0.04 +0.04 -0,01
D...872/873... 110 110 250
0 +0.01 -0,03
+0.04 +0.04 -0,01
D...972/973... 120 120 300
0 +0.01 -0,03
6.3- Check the ambient temperature;

The ambient temperature must be between +5 ºC to +40 ºC for standard type gear units. If
different contact YILMAZ REDUKTOR for special solutions.
6.4- Check the voltage supply;

The standard geared motors are supplied with 230/400 V 50/60 Hz up to 3 kW including 3
kW and 400/690 V 50/60 Hz over 3 kW and is indicated on the motors name plate unless it
is differently ordered.
In case of only gear unit is supplied from YILMAZ REDUKTOR please observe the name
plate of the electric motor and the instructions of the supplier. Check the basic electric con-
nection diagrams below. Use experienced electric technician.
Using wrong connection or voltage can damage the electric motor or environment.
22
D Series
Installing
The following wiring diagram is for standard 230/400 V 50 Hz AC electric motors. For dif-
ferent voltages please contact YILMAZ REDUKTOR. For gear units supplied without motor,
refer to the motor manufacturers user manual.
The electric connection must be done by experienced electric technician.

The gearbox, the motor and the brake must be grounded to prevent potential differences of
earth and gearbox/motor.
Nominal Powers at 400V, 50Hz

Pole Number
230V ( D ) / 400 V ( Y ) 400V ( D )
2 or 4 ≤ 3 kW ≥ 4 kW
6 ≤ 2,2 kW ≥ 3 kW
8 ≤ 1,5 kW ≥ 2,2 kW
Starting Principle Direct Direct or Y/D
Basic motor connection wiring diagram
L1 L2 L3 L1 L2 L3
U U U U
(230V) (230V) (400V) (400V)
U U
(230V) (400V)
I1 I2 I3 I1 I2 I3
V1
U2 V1
U
Uph=
Uph=U 3
I
3
V2
Iph=
W2
=I
U1 V2 I ph U2
W1
W2 W1 U1
W2 U2 V2 W2 U2 V2
U1 V1 W1 U1 V1 W1
L1 L2 L3 L1 L2 L3
23
D Series
Installing
Standard type brakes basic wiring diagram
The electric connection must be done by experienced electric technician.

The gearbox and the motor must be grounded to prevent potential differences of earth
and gearbox/motor.
Delayed Running Brake Sudden Brake

( 220 V) (220 V)
R S T R S T N
Fren Bobini
Brake Coil Brake
Fren Coil
Bobini
M
3
M
3
Delayed Running Brake Sudden Brake

( 24 V) (24 V)
Brake
Fren Coil
Bobini R S T N Brake
Fren Coil
Bobini
R S T N
3
M M
3
24
D Series
Installing
6.5- Check the mounting position;

The mounting position must be in accordance with the mounting position mentioned on the
name plate. If different please contact YILMAZ REDUKTOR for possibilities of using in a
different mounting position. Refer to the mounting positions and oil quantities on this manual
and adjust the oil level accordingly with the recommended oil types given on this manuel.
Do not mix synthetic oils with mineral oils which can cause serious damage on the gear unit.
6.6- Use of breather plug;

Breather plugs are not needed for D series under normal ambient and working conditions
(Up to 30 ºC ambient temperature and up to 8 hours per day) . If heavy ambient conditions
and long time working hours then breather plug are recommended by YILMAZ REDUKTOR
and delivered with the gearbox together. Replace the breather plug with the most top plug
according to your mounting position.
Some plug positions are not machined according mounting position. If no mounting position
is mentioned by ordering, the standard M1 position plugs are machined.
6.7- Check the oil level ;

On the mounting position tables the oil level plug is shown. Please refer to those tables and
be sure that the oil level is correct according the mounting position by screwing half way out
the level plug and see if oil comes out from that plug. If oil comes out tighten the plug again.
If no oil comes out take out the filling plug and add oil until oil comes out from the level plug
and tighten both plugs after finish. Be sure you are using the correct oil mentioned on the
oil tables on this manual.
Do not mix synthetic oils with mineral which can cause serious damage on the gear unit.
6.8- Check shaft ends and mounting faces;

Before you start to installing be sure that all the connection elements are free of oil and dust.
The output shaft may be protected by anti-corrosion oil. Please remove this using available
solvents on your market. By using this do not touch sealing lips or painting of the housing.
6.9- Cover abrasive ambient;

If the gear unit will be placed on a abrasive ambient be sure that the output seals are
covered so that no abrasive material, chemicals or water touches the seals. Any pressure
coming from outside over the seals can cause that the out staying substances to enter the
gearbox and cause serious damage to the gear unit. If pressure or abrasive material can
not be prevented from coming over the sealing, contact YILMAZ REDUKTOR for solutions.
Abrasive material, chemicals, water, positive or negative pressure exceeding 0,2 bar can
affect or damage the sealing lip or output shaft. Inside entering substances from the seals
can cause serious damage to the gear unit.
25
D Series
Installing
6.10- Check accessibility to filling, breather and drain plugs;

The filling, breather and drain plugs must be freely accessible for further checking and service.
7- Mechanical Installation
The gear unit can only be installed using the supplied connection points like foot and flange
assembling points.
To install the gear unit without the supplied connection points can cause serious injuries by
loosening or braking the gear unit. Even the gear unit is installed totally correctly according
this manual, be sure that no one will be harmed by accidentally brake downs or loosening.
The mounting plate must be rigid enough not allowing torsions, flat enough to prevent strains
by tightening the bolts and stable enough not allowing vibrations. By using chain drives this
becomes much more important because of the polygon effect on chain drives. According to
your connection elements the maximal permitted radial and axial load of the gear unit must
be in accordance with your application. Check the product catalogue for permitted radial
loads and calculation.
If the output or input shaft is overloaded by radial or axial loads it can cause serious damage
to the gear unit.
Secure the gear unit using 8.8 or higher quality bolts.
Cover all the turning parts from human entering or touching. Turning parts can cause severe
or fatal injuries.
For different kind of basic installations refer to the following illustrations.
26
D Series
Installing
7.1- Installing customer shaft with shoulder

7.1.1- Use anti-seize assembling paste available on your market. Use a brush to apply the
paste.
7.1.2 -Fasten the bold as shown below.
1 2 3 4 5 6
1
23 1- Retaining Bolt
4 2- Lock Washer
3- Washer
4- Circlip
5- Hollow Shaft
6- Customer Shaft
5
27
D Series
Installing
7.2- Installing customer shaft without shoulder

7.2.1- Use anti-seize mounting paste available on your market. Use a brush to apply the paste.
7.2.2- Fasten the bold as shown below.
1 2 3 4 5 6
1
23
4
1- Retaining Bolt
2- Lock Washer
3- Washer
4- Circlip
5- Hollow Shaft
5 6- Customer Shaft
28
D Series
Installing
7.3- Disassembling customer shaft with shoulder

7.3.1- Disassemble the bolt and take out the parts as shown
1
23
4
5
6
7.3.2- Use the disassemble set from YILMAZ and fasten the bold as shown bellow to take
out the output shaft. For disassemble sets look the following pages.
1 2 3 4 5 6
1
2 1- Retaining Bolt
3 2- Circlip
4
3- Lock Washer
4- Washer
5- Hollow Shaft
6- Customer Shaft
29
D Series
Installing
7.4- Disassembling customer shaft without shoulder

7.4.1- Disassembly the bolt and take out the parts as shown
1
2
3
4
5
5
6
7.4.2 -Use the disassembly set from YILMAZ and fasten the bold as shown bellow to take
out the output shaft. For disassembly sets look the following pages.
1 2 3 4 5 6
1
2 1- Retaining Bolt
3 2- Circlip
4
3- Lock Washer
4- Washer
5- Hollow Shaft
6- Customer Shaft
30
D Series
Installing
7.5- Shaft tightening torques

Use the following table for shaft tightening torques.
Tightining Torque
Type Bolt
[Nm]
D.072/073 M10 20
D.172/173 M10 20
D.272/273 M12 20
D.282/283 M16 40
D.372/373 M16 40
D.472/473 M16 40
D.572/573 M20 80
D.672/673 M20 80
D.772/773 M24 200
D.872/873 M24 200
D.972/973 M24 200
31
D Series
Installing
7.6- Advised Shaft Dimensions and Accessiories
b (max)
b1 b2 b3
f c
t
t1 h6
m1 Ød1 Ød
M
e1 e
45°
s u
g (DIN 332)
Type s u e1 t1 M d d1 m1 f b b1 b2 b3 c g h e t
D.07.. 24.7 8 28 7.5 M12 25 24 30 82 45 18 19 1 M10 24 28 8
D.17.. 29.7 10 33 7.5 M12 30 29 36 89 50 20 19 1 M10 24 33 8
D.27.. 34.7 12 38 9.5 M16 35 34 43 114 65 27 22 1 M12 30 38 10
D.28.. 39.7 12 43 11.5 M20 40 39 50 124 69 28 27 2 M16 38 43 12
D.37.. 39.7 12 43 11.5 M20 40 39 50 138 75 35 28 2 M16 38 43 12
D.47.. 49.7 12 53.5 13.5 M20 50 49 60 5 165 87 41 37 3 M16 38 53.5 14
D.57.. 59.7 16 64 17.5 M24 60 59 75 188 101 44 43 3 M20 44 64 18
D.67.. 69.7 16 74.5 19.5 M24 70 69 85 248 115 78 55 4 M20 44 74.5 20
D.77.. 89.7 20 95 24.5 M30 90 89 110 287 140 83 64 4 M24 52 95 25
D.87.. 109.7 20 116 27.5 M30 110 109 130 347 165 98 84 4 M24 52 116 28
D.97.. 119.7 20 127 31 M30 120 119 140 434 185 130 119 4 M24 52 127 32
Dismounting Mounting
6 Contour Bolt
(DIN ISO 4014 . DIN ISO 4017)
(DIN ISO 8765)
32
D Series
Installing
7.7- D.07.. - D.97.. DIMENSIONS OF SPLINED HOLLOW SHAFT TO DIN 5480
DIN5480
l4 l3
MxL
Ø da2
Ø df2
Ød1
Ød
Ød
l1 l2 l2 l1
l
Type DIN5480 ød ød1 ød2 øda2 ødf2 l l1 l2 l3 l4 MxL
D07 N25x1.25x30x18x9H 27 26 48 22.5 25.25 104 17 22 20 20 M10x30

D17 N30x1,25x30x22x9H 32 31 53 27,5 30,25 120 18 25 20 20 M10x30
D27 58 157
N35x2x30x16x9H 37 36 31 35,4 18 35 20 20 M10x30
D28 63,5 166
D37 N45x2x30x21x9H 47 46 74 41 45,4 185 25 45 24 32 M16x50
D47 N50x2x30x24x9H 55 51 84 46 50,4 215 25 55 24 32 M16x50
D57 N65x2x30x31x9H 72 66 104 61 65,4 246 25 65 30 40 M20x60
D67 N70x2x30x34x9H 72 71 119 66 70,4 308 25 75 30 40 M20x60
D77 N85x3x30x27x9H 90 86 139,5 79 85,6 363 26 90 30 40 M20x60
D87 N100x4x30x24x9H 110 101 169 92 100,8 428 30 105 41 50 M24x80
D97 N120x4x30x28x9H 130 121 179 112 120,8 500 35 120 41 50 M24x80
l1 DIN 5480
g(DIN332)
Ød (h6)
Me
Dm l2 l3 l4
Me g
Type DIN5480 ød l1 l2 l3 l4 Dm
(Tolerances) (DIN332)
D07 W25x1,25x30x18x8f 27 44 10 7 27 28,01 (0/-0,03) 2.75 M10x24

D17 W30x1,25x30x22x8f 32 48 11 7 30 33,05 (0/-0,04) 2,75 M10x24
D27
W35x2x30x16x8f 37 58 11 7 40 38,94 (0/-0,05) 4,00 M10x24
D28
D37 W45x2x30x21x8f 47 75 18 7 50 48,88 (0/-0,05) 4,00 M16x38
D47 W50x2x30x24x8f 55 85 18 7 60 54,16 (0/-0,05) 4,00 M16x38
D57 W65x2x30x31x8f 72 95 17 8 70 68,99 (0/-0,06) 4,00 M20x44
D67 W70x2x30x34x8f 72 105 17 8 80 74,18 (0/-0,06) 4,00 M20x44
D77 W85x3x30x27x8f 90 121 16 10 95 91,02 (0/-0,05) 6,00 M20x44
D87 W100x4x30x24x8f 110 140 20 10 110 108,37 (0/-0,06) 8,00 M24x52
D97 W120x4x30x28x8f 130 160 23 12 125 127,89 (0/-0,06) 8,00 M24x52
33
D Series
Installing
7.8- Assembling customer shaft with shrink disk

7.8.1- Loosen the bolts of the shrink disk
7.8.2- Use a solvent available in your market to clean all the dirt an oil from the shaft
and shrink disk hollow. The surfaces must be free from oil or any dirt. The solvent
must be removed from the surfaces as well.
34
D Series
Installing
7.8.3- Insert the shaft and tighten the bolts as shown. Be sure that there is a clear-
ance between the shrink disk shoulder and the hollow shaft shoulder of the gearbox.
1 2 3 4
1- Customer Shaft
2- Bronze Ring
3- Hollow Shaft
4- Shrink Disk
Tightening
Type Bolt Quantity
Torque [Nm]
D.07.. M5 6 4
D.17.. M6 5 12
D.27.. M6 7 12
D.28.. M6 8 12
D.37.. M6 8 12
D.47.. M6 10 12
D.57.. M8 7 30
D.67.. M8 7 30
D.77.. M10 9 59
D.87.. M12 10 100
D.97.. M12 12 100
35
D Series
Installing
7.9- Disassembling customer shaft with shrink disk

7.9.1- Loosen the bolts of the shrink disk and take out the shaft.
36
D Series
Installing
7.10- Assembling gear unit with torque arm

7.10.1- Use the torque arm connection according the following drawing.
Machine
Machine
37
D Series
Installing
7.10.2- Assemble the parts as shown bellow
7
6
5
4
4
1 23
1- Bolt 4- Rubber Buffer 7- Bolt
2- Washer 5- Bolt
3- Washer Ring 6- Fixing Plate
38
D Series
Installing
7.10.3- For the fixing bold position refer to the following dimensions
b
b1
h1 Ød
Type d b b1 h h1
D.07. 14 42 21 147 26.5
D.17. 17 54 27 158 31.5
D.27. 17 54 27 170 32
D.28. 17 54 27 198 40.5
D.37. 17 56 28 218 41
D.47. 22 80 40 278 50
D.57. 22 86 43 346 62
D.67. 26 110 55 395 70
D.77. 26 116 58 485 88
D.87. 32 160 80 550 110
D.97. 32 165 82.5 660 150
39
D Series
Installing
7.11- Fitting outputshaft elements

Use the following illustration to assemble output shaft units
1) Gear shaft end

2) Thrust bearing
3) Coupling hub
7.12- Correct position of output shaft elements

The Output Shaft unit (transmission elements) must placed as close as possible to
the gear unit so that the radial load is as closest as possible to the gear unit.
1) Hub
40
D Series
Installing
7.13- Fitting Couplings

7.13.1- By fitting couplings be sure that there is some clearance between the two elements
7.13.2- By fitting couplings be sure that there is no eccentric between the two shafts.
7.13.3- By fitting couplings be sure that the two shafts are not angular miss-aligned.
41
D Series
Maintenance and Inspections
8- Maintenance and Inspections

Under normal ambient and working conditions the gear unit should be checked according the follow-
ing intervals. (For definition of normal working conditions refer to the product catalogue: “Selecting
Gearbox” section);
Every 10.000
Item to check /replace Every 3.000 working hours Every 4.000 working Every 25.000
working hours or
or every 6 months hours working hours
every 3 years
Check for oil leakage x
Check for oil level x
Check oil leakage from

x
seal
Check Rubber buffer x (Change if necessary)
Check Bearings Noise x (Change if necessary)
x (See Below for

Change Mineral Oil
details)
Change Synthetic-PAO x (See Below for

Oil details)
Change Sealing x
Change Bearing Grease x
Change Bearings x
Check for noise Changes x
45000
40000
Oil change interval [Hours]
35000
30000
Mineral
25000
Synthetic PAO
20000 Synthetic PG
15000
10000
5000
0
70 80 90 100 110 120 130 140 150 160
Oil bath temperature (Celcius)
For normal ambient conditions 70 ºC oil bath temperature should be taken as reference
* For D series mineral oil is used unless it is differently ordered. For oil type and quantities
refer to the following table.
42
D Series
Lubrication
9- Lubrication
9.1- Oil Types
Ambient Temperature Beyond Klüber
Aral Petroleum Castrol Lubrication Mobil Shell Total
[ºC]
Lubricant DIN ISO
51517-3 VG
Forced
Dip Lubri- Lubrica-
cation tion
Degol Energol Alpha Klüberoil Mobilgear Omala Carter

0 ... +50 – 680
BG 680 GR-XP 680 SP 680 GEM 1-680 N XMP 680 680 EP 680
-5 ... +45 – 460
BG 460 GR-XP 460 SP 460 GEM 1-460 N XMP 460 F460 EP 460
-10 ... +40 +15 ... +40 320
Mineral BG 320 GR-XP 320 SP 320 GEM 1-320 N XMP 320 F320 EP 320
Oil CLP
-15 ... +30 +10 ... +30 220
BG 220 GR-XP 220 SP 220 GEM 1-220 N XMP 220 F220 EP 220
-20 ... +20 +5 ... +20 150
BG 150 GR-XP 150 SP 150 GEM 1-150 N XMP 150 150 EP 150
Degol Energol Alpha Klüberoil Omala Carter
-25... +10 +3 ... +10 100 –
BG 100 GR-XP 100 SP 100 GEM 1-100 N 100 EP 100
Degol Energsyn Klübersynth Mobil Tivela Carter
-10 ... +60 – 680 –
GS 680 SG-XP 680 GH 6 -680 Glygoyle 680 S 680 SY 680
Degol Energsyn Aphasyn Klübersynth Mobil Tivela Carter
-20 ... +50 – 460
GS 460 SG-XP 460 PG 460 GH 6 -460 Glygoyle 460 S 460 SY 460
Degol Energsyn Aphasyn Klübersynth Mobil Tivela Carter
-25 ... +40 +5 ... +40 320
GS 320 SG-XP 320 PG 320 GH 6 -320 Glygoyle 320 S 320 SY 320
CLP PG
Degol Energsyn Aphasyn Klübersynth Tivela Carter
-30 ...+30 0 ...+30 220 –
GS 220 SG-XP 220 PG 220 GH 6 -220 S 220 SY 220
Degol Energsyn Aphasyn Klübersynth Tivela Carter
-35 ... +20 -5 ... +20 150 –
GS 150 SG-XP 150 PG 150 GH 6 -150 S 150 SY 150
Klübersynth
Synthetic -40 ... +10 -8 ... +10 100 – – – – – –
GH 6 -100
Oil
Mobilgear
Klübersynth Carter
-10 ... +60 – 680 – – – SHC XMP –
GEM 4-680 N SH 680
680
Mobilgear
Degol Enersyn Alphasyn Klübersynth Omala Carter
-20 ... +50 – 460 SHC XMP
PAS 460 EP-XF 460 T 460 GEM 4-460 N HD 460 SH 460
460
Mobilgear
-25 ... +40 +5 ... +40 320 SHC XMP
CLP HC 320
Mobilgear
-30 ... +30 0 ...+30 220 SHC XMP
220
Mobilgear
-35 ... +20 -5 ... +20 150 SHC XMP
150
Klübersynth
-40 ... +10 -8 ... +10 100 – – – – – –
GEM 4-100 N
Food Grade Mobil Cassida

CLP Optileb Klüberoil Nevastane
Oil -15 ... +25 +5 ... +25 220 – – SHC Fluid
NSF H1 GT 220 4 UH1-220 N SL 220
Cibus 220 GL-220
Biodegra- Tribol
Klübersynth Carter
dable Oil CLP E -25 ... +40 +5 ... +40 320 – – BioTop – –
GEM 2-320 Bio 320
1418-320
Multis
Mineral Grease Aralub Energrease Spheerol Centoplex Mobilux Alvania
Complex
HL3 LS 3 AP3 2 EP EP 3 RL3
[ -20 .... +120 Working Temperature ºC] EP 2
Multis
Synthetic Grease Energrease Petamo Mobiltemp Cassida
– – Complex
SY 2202 GHY 133 N SHC 100 RLS 2
[ -30 .... +100 Working Temperature ºC] SHD 220
43
D Series
Lubrication
9.2- Changing the oil

Refer to the nameplate to find out the correct oil filled inside the gearbox.
-Do not mix synthetic oils with mineral oils which will cause serious damage to the gear
unit. The oil change must be done by using the filling, draining and level plugs according
the mounting position illustrated in section 9.4.
- Extended, intensive contact with oils can lead to skin irritations.

Avoid extended contact with oil, and clean oil off skin thorough.
- Hot oil can cause scalding.

When changing oil, protect yourself against contacting hot oil.
44
D Series
Lubrication
9.3 Mounting Positions
M1
M2
M5
Figured mounting positions of M1 to M6 are de-

termined as reference of directional position of
the gearbox. Mounting surfaces are not binding.
M4
M6
M3
M1
M5
M2
Figured mounting positions of M1 to M6 are determined

as reference of directional position of the gearbox. Mount-
ing surfaces are not binding.
M4
M6
M3
45
D Series
Lubrication
9.4 Oil Plugs and Oil Quantities:
D Series 2-3 Stage Oil Level Plugs:
M1 M2 M3
M4 M5 M6
Oil Quantities (lt)

Type M1 M2 M3 M4 M5 M6
DR072 0.95 1.1 0.8 1.1 1.0 0.9
DR073 0.9 1.0 0.7 1.0 0.9 0.85
DR172 1.3 1.5 1.0 1.6 1.4 1.3
DR173 1.0 1.3 0.8 1.55 1.2 1.2
DR272 1.9 2.2 1.3 2.5 2.0 1.95
DR273 1.8 2.0 1.2 2.0 2.0 2.0
DR282 2.4 3.0 2.0 2.9 2.7 2.7
DR283 2.3 2.9 1.8 2.6 2.3 2.5
DR372 3.2 3.7 2.4 3.6 3.5 3.4

DR373 3.0 3.7 2.0 3.5 3.3 3.3
DR472 6.8 7.0 4.6 7.5 6.5 6.5
DR473 6.4 7.0 4.0 6.6 6.5 6.5
DR572 11.4 12.7 8.6 15.0 11.9 11.6
DR573 11.2 12.4 8.0 12.5 11.5 11.5
DR672 22.0 27.0 16.0 27.0 22.8 22.5
DR673 21.0 25.2 14.0 26.5 21.5 21.0
DR772 34.0 37.0 26.0 44.0 35.0 34.5
DR773 32.0 35.0 21.0 40.0 33.0 32.5
DR872 53.0 58.0 43.0 67.0 55.0 54.0
DR873 48.5 53.0 39.0 61.0 50.0 49.0
DR972 87.0 113.0 80.5 117.0 97.0 95.0
DR973 84.0 110.0 77.0 112.0 93.0 89.0
Symbols : : Drain Plug : Oil Filling : Vent Plug : Oil Level
46
D Series
Lubrication
Oil Plugs and Oil Quantities
D Series 4 Stage Oil Level Plugs
A A
B A
B B
M1 M2 M3
B A
A B
B
A
M4 M5 M6
Oil Quantities (lt)

M1 M2 M3 M4 M5 M6
Type
A/B A/B A/B A/B A/B A/B
DR474 6.4/ 0.25 7.0 / 0.25 4.0 / 0.25 6.6 / 0.25 6.5 / 0.25 6.5 / 0.25
DR574 11.2 / 0.4 12.4 / 0.4 8.0 / 0.4 12.5 / 0.4 11.5 / 0.4 11.5 / 0.4
DR674 21.0 / 0.5 25.2 / 0.5 14.0 / 0.5 26.5 / 0.5 21.5 / 0.5 21.0 / 0.5
DR774 32.0 / 0.9 35.0 / 0.9 21.0 / 0.9 40.0 / 0.9 33.0 / 0.9 32.5 / 0.9
DR874 48.5 / 3.5 53.0 / 3.5 39.0 / 3.5 61.0 / 3.5 50.0 / 3.5 49.0 / 3.5
DR974 84.0 / 5.0 110.0 / 5.0 77.0 / 5.0 112.0 / 5.0 93.0 / 5.0 89.0 / 5.0
47
D Series
Lubrication
9.4 Oil Plugs and Oil Quantities:
D Series 5-6 Stage Oil Level Plugs:
B A
A A
B
B
M1 M2 M3
B A A
B
B
A
M4 M5 M6
Oil Quantities (lt)

M1 M2 M3 M4 M5 M6
Type
A/B A/B A/B A/B A/B A/B
DR275 1.8 / 0.4 2.0 / 0.6 1.2 / 0.5 2.0 / 0.6 2.0 / 0.5 2.0 / 0.5
DR276 1.8 / 0.35 2.0 / 0.55 1.2 / 0.5 2.0 / 0.55 2.0 / 0.4 2.0 / 0.4
DR285 2.3 / 0.4 2.9 / 0.6 1.8 / 0.5 2.6/ 0.6 2.3 / 0.5 2.5 / 0.5
DR286 2.3 / 0.35 2.9 / 0.55 1.8 / 0.5 2.6 / 0.55 2.3 / 0.4 2.5 / 0.4
DR375 3.0 / 0.4 3.7 / 0.6 2.0 / 0.5 3.5 / 0.6 3.3 / 0.5 3.3 / 0.5
DR376 3.0 / 0.35 3.7 / 0.55 2.0 / 0.5 3.5 / 0.55 3.3 / 0.4 3.3 / 0.4
DR475 6.4 / 0.65 7.0 / 0.95 4.0 / 0.7 6.6 / 0.95 6.5 / 0.7 6.5 / 0.7
DR476 6.4 / 0.6 7.0 / 0.8 4.0 / 0.7 6.6 / 0.8 6.5 / 0.65 6.5 / 0.65
DR575 11.2 / 1.2 12.4 / 2.1 8.0 / 2.0 12.5 / 2.1 11.5 / 1.4 11.5 / 1.4
DR576 11.2 / 1.1 12.4 / 2.0 8.0 / 1.9 12.5 / 2.0 11.5 / 1.3 11.5 / 1.3
DR675 21.0 / 1.2 25.2 / 2.1 14.0 / 2.0 26.5 / 2.1 21.5 / 1.4 21.0 / 1.4
DR676 21.0 / 1.1 25.2 / 2.0 14.0 / 1.9 26.5 / 2.0 21.5 / 1.3 21.0 / 1.3
DR775 32.0 / 2.0 35.0 / 3.4 21.0 / 3.1 40.0 / 3.4 33.0 / 2.8 32.5 / 2.8
DR776 32.0 / 1.9 35.0 / 3.3 21.0 / 3.0 40.0 / 3.3 33.0 / 2.6 32.5 / 2.6
DR875 48.5 / 2.0 53.0 / 3.4 39.0 / 3.1 61.0 / 3.4 50.0 / 2.8 49.0 / 2.8
DR876 48.5 / 1.9 53.0 / 3.3 39.0 / 3.0 61.0 / 3.3 50.0 / 2.6 49.0 / 2,6
DR975 84.0 / 4.5 110 / 7.5 77.0 / 7.5 112 / 7.5 93.0 / 5.5 89.0 / 5.5
DR976 84.0 / 4.0 110 / 7.0 77.0 / 7.0 112 / 7.0 93.0 / 5.0 89.0 / 5.0
48
D Series
Troubleshooting Guide
10- Troubleshooting Guide
All the operations bellow must be done by authorized and skilled mechanician/electrician.
Inform YILMAZ REDUKTOR before making any change to the gearbox. Only oil change is allowed
to change without information. Do not make any think if you are not sure what you are doing and
contact YILMAZ. Any change or operation done without the information of YILMAZ REDUKTOR is in
your own risk and responsibility and YILMAZ REDUKTOR does not take any responsibility.
ID Problem Observation Remedy
You hear no noise and shaft Please Check the voltage supply and frequency of your electric
Gearbox Does Not is not turning. You are not connection. They must be in accordance with the nameplate of
001
Start Up using any driver or frequency the motor. Observe motor manufacturers start up manual. Still
inverter. does not work go to ID 100
You hear no noise and shaft Please observe the frequency incerter/driver manual. Chech
Gearbox Does Not
002 is not turning. You are using the motor by supplying direct voltage to see if the problem is on
Start Up
frequency inverter or driver. your driver/frequency inverter. Still does not work go to ID 001.
Please Check the voltage supply and frequency of your electric

connection. They must be in accordance with the nameplate of
You hear some noise but both the motor. Observe motor manufacturers start up manual. Still
motor shaft and gearbox shaft same problem, the load may be too high for the choosen motor.
Gearbox Does Not
003 is not turning. You are not Loosen the gearbox from the load/torque.
Start Up
using any driver /frequency in- If it works than the starting torque is insufficient and higher mo-
verter or braked motor. tor power is needed. For monophaze motors, check the star-
ting up condansator and running condansator as well. If notting
helps go to ID 100
Please observe the frequency inverters or drivers manual. To

You hear some noise but both
see if the problem is on your driver or frequency inverter take
Gearbox Does Not motor shaft and gearbox shaft
004 out the driver/frequency inverter and make direct voltage sup-
Start Up is not turning. You are using
ply to the motor according the motors nameplate. Still does not
driver or frequency inverter.
work go to ID 100
005 Gearbox Does Not You hear some noise but both Please Check the voltage supply and frequency of your electric
Start Up motor shaft and gearbox shaft connection. They must be in accordance with the nameplate of
is not turning. You are using the motor. Observe motor manufacturers start up manual. Be
braked motor sure that the brake is working. Observe the brake manufactur-
ers manuel. If brake is supplied from YILMAZ observe this ma-
nuel for correct brake wiring diagram. If still not work supply the
brake with voltage according its nameplate directly. For exam-
ple 198V DC. You will hear a clicking noise explaining that the
brake is opening. If you hear no noise the brake or rectifier is
defect. If you hear the clicking noise the brake is working. You
should this clicking noise by your normal electric connection as
well. By supplying direct supply to the brake you hear the click-
ing noise and at same time you supply the motor with direct
voltage according to its name plate and still same problem, the
load may be too high for the choosen motor. Goto ID 003.
49
D Series
For very low speeds the frequency inverters frequency is lowering down.
For very low frequencies the inverter parameter and motor parameter
Gearbox Does Not
must be optimized. Also for low speeds the efficiency of the gearbox may
006 Work in Low Speeds/ You are using
varry too much. Specially for worm-gearboxes. The recomended frequ-
frequencies. frequency inverter.
ency range is 20-70 Hz for worm-gearboxes and 10-70 Hz for Helical
Gear Boxes. Use Higher motor power and Frequency inverter or change
ratio of gearbox to work inside the reccomended range.
The oil is not in accordance with your working conditions. Change to lo-
Gearbox Does Not
007 Ambient Temperature wer viscosity oils. Observe this manuel for using the correct oil. Working
Start Mornings or Af-
is below +5 Celsius in higher ambient temperatures is an other solution if possible. If still
ter Long Time Stop.
same problem you need higher motor power.
Measure the surface temp. using a temperature measuring device

under full load. If the temp is under +80 Celsius this will make no harm
to the gearbox and is normal. All ATEX conforming gearboxes and
You are using Worm
standart worm gearboxes are designed to work under max. +120 Cel-
Gearbox is Heating Gear Box and ambient
008 sius. If higher than +120 Celsius and using ATEX conforming gear box
Up too Much tenp is lower than +40
immidiately stop the system and contact YILMAZ REDUKTOR. Go to
Celsius
ID 100. If not ATEX confirming check the oil type and oil quantitiy/level
according your mounting position and check the nameplate mounting
position. If nameplate mounting position does not fit the actual position
goto ID 100.
Measure the surface temp. using a temperature measuring device
under full load. If the temp is under +80 Celsius this will make no harm
to the gearbox and is normal. All ATEX conforming gearboxes are
You are using Helical
designed to work under max. +120 Celsius. If higher than +120 Celsi-
Gearbox is Heating Gear Box. Ambient
009 us and using ATEX conforming gear box immidiately stop the system
Up too Much temp is lower than +40
and contact YILMAZ REDUKTOR. If not ATEX gearbox the gearbox is
Celsius
designed to work under max. +80 Celsious. If higher than +80 Celsius
check the oil type and oil quantitiy/level according your mounting positi-
on and check the nameplate mounting position. If nameplate mounting
position does not fit the actual position goto ID 100
Standart Gearboxes are designed to work under +40 Celsius. ambient

010 Gearbox is Heating Ambient Temp is over
temperature. If ambient temp is higher than +40 Celsius special soluti-
Up too Much +40 Celsius
ons/gearboxes are required. Please contact YILMAZ REDUKTOR.
Check Your moving parts for noise. Disassemble the gearbox and run
Noise is regular
011 Gearbox is noisy without load. If you still hear the noise motor bearings or gearbox bea-
continious
rings are defect. Change bearings. Goto ID 100
Check Your moving parts for noise. Disassemble the gearbox and run
012 without load. If you hear still the noise the oil may has some particles
Gearbox is noisy Noise is random
inside. Change the oil and look for small particles. If metal particles are
found the gearbox may have some demage. Goto ID 100
50
D Series
Check Your moving parts for noise. Disassemble the gearbox and
013 Gearbox is noisy Regular nocking noise run without load. If you still hear the noise one of the gears inside is
defect. Goto ID 100
Check the output-shaft connection alements for runout. Take out the
014 Gearbox is noisy Regular up and down noise output shaft element and run without load. If you still hear the noise
one of the gears has runout problem. Goto ID 100
Gearbox is with braked motor Low randomly clicking noise may come from the brake disk which is
015 Gearbox is noisy and noise is comming from the normal. If noise level is disturbing the brake may be defect or brake
brake side randomly. clearance is not adjusted. Goto ID 100
The frequency inverter parameters are not optimized for the frequ-
You are using frequency inver-
ency range or motor you are using. Observe the frequency inverters
016 Gearbox is noisy ter and the noise level is chan-
manual. If still same problem change the ratio of gearbox. Goto ID
ging according your speed.
100
If ambient Temp is over +40 Celsious or none stop work over 16
hours please change the top plug with a breather plug. Observe this
017 Oil is Leaking Oil Leakage from Seal
manual for using breather plug. If this is not your case the seal could
be damaged. Goto ID 100
If you are using breather plug be sure it is in the correct place. This
is the most top plug position according your mounting position. The
018 Oil is Leaking Oil Leakage from Plug plug may be not tight enough. There are some particles under the
plug rubber surface. Clean and tifgten the plug. If still same problem
goto ID 100
Observe exactly where the oil is comming out. It could be seal or
plug point where it comes out and leakes over the housing. If this is
019 Oil is Leaking Oil Leakage from Housing
your case goto ID 018/019. If you are sure oil comes out from hou-
sing than housing has some micro split / crack. Goto ID 100
The sealing liquit under cover is split/defect. Disassemle the cover

020 Oil is Leaking Oil Leakage from Cover and put new sealing liquit. Assemle the cover and tighten the bolts.
If still same problem goto ID 100
Gearbox is
The movement of gear box is because of the runout of the shaft
021 moving regularly
You are using Torque Arm which you assemle the gearbox. This has no bad affect or harm to
on its mounting
the gearbox and is normal unless you are using torque arm.
point
The movement of gear box is because of the runout and clearance
Gearbox is
of the shaft which you assemle the gearbox. Check the clearance of
022 moving randomly
You are using Torque Arm the assemling shaft and the clearances on your machine. This has
on its mounting
no bad affect or harm to the gearbox unless you are using torque
point
arm.
Motor is heating Motor is running over its The motor power is not enough or some overload to the motor is
023
up nominal current possible. The motor may be defect. Goto ID 100
Check the motor Fan Hub and rips. They must be free of dust. If you
023 Motor is heating are using forced external fan, check if it is working. If you are using
Ambient is dusty
up frequency inverter in low speeds and you do not have forced exter-
nal fan, you may need forced external fan. Goto ID 100
51
D Series
Motor is running but

024
Gearbox shaft does Scratchinh noise comes out Some part (key, gear) may be defect inside gearbox. Goto ID 10
not turn
The radial load or poligon effect of the chain may have caused
the damage. Check also if the assembly bolts are loosened or
the plate you assemble the gearbox is rigit enough. Check if you
025 Gearbox Housing is You are using chain drive or
are using the correct diameter of chain drive and you are not
Defect pinion gear
exceeding max. allowed radial load. Check the position of your
output element and re-calculate your radyal load and check if this
fit to the maximum allowed radial load. Goto ID 100
The radial load or poligon effect of the chain may have caused
the damage. Check also if the assembly bolts are loosened or
the plate you assemble the gearbox is rigit enough. Check if you
You are using chain drive or
026 Output Shaft is Defect are using the correct diameter of chain drive and you are not
pinion gear
exceeding max. allowed radial load. Check the position of your
output element and re-calculate your radyal load and check if this
fit to the maximum allowed radial load. Goto ID 100
Please check the wiring diagram of the brake. There are two
Gearbox is stopping different kind of brake wiring diagram. The standart gearbox de-
027 You are using braked motor
too late livered from our factory is set to delayed braking. For sudden
braking check the wiring diagram.
For fast opening of big brakes (over 100Nm), you may need
Gearbox is starting too
028 You are using braked motor shock transformators which is supplied by YILMAZ. Goto ID 100
late
Please contact YILMAZ REDUKTOR Service point. See on the

back side of this manual. Changing mechanical parts of gearbox
can only be done by YILMAZ REDUKTOR or with information
100 Service Required No self solution found
of YILMAZ REDUKTOR. Any change without informing YILMAZ
REDUKTOR will cancel the waranty, manufacturer decleration
and YILMAZ REDUKTOR will take no responsibility.
11- Disposal
If your product is no longer of use and you wish to dispose of it, refer to the instructions here. If you
have any questions regarding ecological disposal methods, please consult our service points given on
the backside of this manuel.
11.1- Disposal of Oil
-Lubricants (oil and greases) are hazardous substances, which can contaminate soil and water.
Collect drained lubricant into suitable receptacles and dispose of it according to the valid national guid-
lines.
11.2- Disposal of Sealings
Remove the sealing rings from the gear reducer, and clean them of oil and grease resudies.
Dispose of the sealings as composite material (metal/plastic)
11.3-Disposal of Metal
Divide up the remainder of the gear reducer into iron, aluminium, non-ferrous havy metal if possible
Dispose of it according to the valid national guidelines.
52
Appendix
Warranty Conditions:
1. The geared motors and gear units are warranted for two year except the electric motor. For
motor warranty please refer to the manual of the electric motor manufacturer or the warranty
document of the motor manufacturer. This warranty is valid only if the gearbox is assembled
and started up according our operating instructions and is used under the allowed conditions
for the appropriate gearbox type in our catalogue. Special Gearbox parts made according
customer request are not covered by this warranty.
2. The warranty time starts from the start up time written on the warranty document and last
for two years. If the start-up time is more then three months after the billing time, the total
warranty time is limited to 27 months starting from billing time. If the warranty document is
not send to our company after start-up, the total warranty time will be limited to 24 months
after the billing time.
3. Any time during the warranty for maintenance, repair or change will be added to the war-
ranty time. This time starts from the date which the company or representative was made
aware of the problem and ends on the date of the re-start-up.
4. If the product fails to operate because of a manufacturing or assembly failure during the
warranty time, the product will be repaired free of charge.
5. If the product fails to operate because of a manufacturing or assembly failure during the
warranty time and it is not possible to repair it, the product will be changed with a new one
according to the report from our service department mentioning that the hazard can not be
repaired.
6. Costumers must inform the manufacturer if there are some problems after the service and
repair of the failed product.
7. The extra costs like stopped plant, physical or mental injuries etc. by the costumer side
are not covered by this warranty except the product itself.
8. The warranty is not valid if the user makes any modifications to the gear unit. e.g. Removal
of namepale, changing of any gear unit parts....
9. Yılmaz Redüktör delivers the repaired gear units to the first customer in the warranty pe-
riod. Yılmaz Redüktör will charge for delivery to the different addresses
YILMAZ REDUKTOR San. ve Tic. A.S.

Ataturk Mah. Lozan Cad. No: 17 P.K.:34522 Esenyurt - Istanbul / TURKEY
Phone: +90 (0) 212 886 90 00, Fax: +90 (0) 212 886 54 57
Warranty Decleration
and
Instruction Manual Receipt Form
YILMAZ REDUKTOR products are warranted for 2 (Two) years covering all parts
and materials used in products and their production errors unless they are started-
up and used according our service manual and is not modified or disassembled
without an acknowledgement from our company.
The warranty covers all costs like repair, service, spare parts etc. and no charge will
be asked under any name. The time for repair, service will be added to the warranty
time.
For detailed warranty conditions please refer the back side of this page.
Serial No:
Type:
Manufacturer:
Company : YILMAZ REDUKTOR Sanayi ve Ticaret A.S.
Ataturk Mah. Lozan Cad. No: 17 P.K.:34522 Kırac-Esenyurt-Istanbul/TURKEY
Phone: +90 (0) 212 886 90 00, Fax: +90 (0) 212 886 54 57
Stamp and Signature
Supplier / End User:

With signing this part and sending this back to our company your warranty period
will be started and you are accepting that you have received the operating in-
struction of the product.
Name:
Billing Date/ Bill No.:
Start-Up Place / Date:
Address:
Phone - Fax:
Supplier/ End User Stamp and Signature

Notes
Notes
Notes
Notes
Domestic Service Spare Parts
Tel: +90 212 886 90 00 Tel: +90 212 886 90 00
Int: 1223, 1228, 1287 Int: 1224, 1277
E-Mail: servis@yr.com.tr E-Mail: yedekparca@yr.com.tr
International Services
If you call the above service point, you will be directed to our nearest service.
Yılmaz Redüktör Sanayi ve Ticaret A.Ş.

Atatürk Mah. Lozan Cad. No: 17, 34522 Esenyurt - İstanbul / Turkey
Tel: +90 212 886 90 00 | Fax: +90 212 886 54 57 | E-Mail: yilmaz@yr.com.tr

Operating Instructions: Parallel Shaft Helical Gearboxes

Uploaded by

Copyright:

Available Formats

Operating Instructions: Parallel Shaft Helical Gearboxes

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Operating Instructions: Parallel Shaft Helical Gearboxes

Uploaded by

Copyright:

Available Formats

OPERATING

1- How To Use This Manual.......................................................................................... 04

3- Part List of Standard Type Gear Units.................................................................... 07

5- Thinks to Check Before the Gear Unit or Geared Motor is Installed................... 20

6- Installing The Gear Unit........................................................................................... 21

8- Maintenance & Inspection....................................................................................... 42

10- Troubleshooting Guide.......................................................................................... 49

Electric Hazard; Can cause severe or fatal injuries.

Mechanical Hazard; Can cause severe or fatal injuries.

Likely to be Hazardous; Can cause minor or fatal injuries.

Damage Risk; Can damage gearbox or environment.

The operating instructions contain important information to ensure;

D R 4 7 4 .02 3 E90S / 4C - L02

Motor Size For DN Types

Motor Efficiency Class

2.2- Nameplate, unit designation

Nameplate unit designation is a short abbreviation from the detailed designation

A sample name plate for D Series

DR- With motor

3- Part List of Standard Type Gear Units

Standard Part List

1- Pin Screw 9- Bearing 17- Seal 25- Gear 33- Bearing

4- Cover Plate 12- Gear 20- Spacer 28- Spacer

5- Screw 13- Spacer 21- Spacer 29- Bearing

6- Oil Seal 14- Bearing 22- Bearing 30- Gear

7- Circlip 15- Spacer 23- Shaft Gear 31- Key

8- Spacer 16- Circlip 24- Key 32- Gear

3.2- D..01... Types for 2 and 3 Staged Gear Units

Only Valid For 3 Stages 1

Standard Part List

5- Bolt 13- Gear 21- Spacer 29- Spacer

6- Oil Seal 14- Spacer 22- Spacer 30- Bearing

7- Circlip 15- Bearing 23- Bearing 31- Gear

8- Bearing 16- Spacer 24- Shaft Gear 32- Key

3.3- D..02... Types For 2 and 3 Staged Gear Units

Standard Part List

7- Circlip 16- Spacer 25- Bearing 34- Key

8- Spacer 17- Circlip 26- Shaft Gear 35- Shaft Gear

9- Bearing 18- Seal 27- Key 36- Bearing

3.4- D..03... Types For 2 and 3 Staged Gear Units 3

Standard Part List

7- Circlip 15- Spacer 23- Spacer 31- Bearing

8- Spacer 16- Circlip 24- Bearing 32- Gear

3.5- D...0S... Types For 2 and 3 Staged Gear Units

Standard Part List

5- Cover Plate 13- Gear 21- Spacer 29- Spacer

6- Bolt 14- Spacer 22- Spacer 30- Bearing

7- Oil Seal 15- Bearing 23- Bearing 31- Gear

8- Circlip 16- Spacer 24- Shaft Gear 32- Key

3.6- D...0E... Types For 3 Staged Gear Units

Standard Part List

1- Circlip 5- Extruder Neck 9- Key

2- Spacer 6- Bolt 10- Hollow Shaft Output

3- Flange 7- Seal 11- Spacer

4- Bolt 8- Bearing 12- Seal

3.7- D..4 Series Additional Stage for 4 Stage Types

1- Circlips 6- Circlips 11- Key

2- Bearing 7- Shaft 12- Key

5- Bearing 10- Circlips 15- Screw Pin