Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 72 views

    DOR-230 PCB #1 Signal Input Error: Point of Detection Application

    Uploaded by

    Daniel Gatdula
    This document provides troubleshooting steps for a "Signal Input Error" occurring on DOR-230 PCB #1. The steps include checking connector contacts, PCB selection switches, cable connections, input port defects, external device voltages, and PCB voltages. If the error persists after these checks, the document recommends replacing the faulty DOR-230 PCB first, then the DOC-200 PCB if needed.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    DOR-230 PCB #1 Signal Input Error: Point of Detection Application

    Uploaded by

    Daniel Gatdula
    72 views1 page
    This document provides troubleshooting steps for a "Signal Input Error" occurring on DOR-230 PCB #1. The steps include checking connector contacts, PCB selection switches, cable connections, input port defects, external device voltages, and PCB voltages. If the error persists after these checks, the document recommends replacing the faulty DOR-230 PCB first, then the DOC-200 PCB if needed.

    Original Title

    TCD-080-DS4

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides troubleshooting steps for a "Signal Input Error" occurring on DOR-230 PCB #1. The steps include checking connector contacts, PCB selection switches, cable connections, input port defects, external device voltages, and PCB voltages. If the error persists after these checks, the document recommends replacing the faulty DOR-230 PCB first, then the DOC-200 PCB if needed.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    72 views1 page

    DOR-230 PCB #1 Signal Input Error: Point of Detection Application

    Uploaded by

    Daniel Gatdula
    This document provides troubleshooting steps for a "Signal Input Error" occurring on DOR-230 PCB #1. The steps include checking connector contacts, PCB selection switches, cable connections, input port defects, external device voltages, and PCB voltages. If the error persists after these checks, the document recommends replacing the faulty DOR-230 PCB first, then the DOC-200 PCB if needed.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    ● Run CPU

    TCD - 080 DOR-230 PCB #1 Signal Input Error


    Point of Application ● DI120-150
    Detection ○ Speed CPU ● DI180-420
    [Meaning]
    When input port values read at 10ms interval in [Actions to take]
    DOR-230 PCB(#1~#4) are not identical for 5 or more consecutive
    times and lasts for 50ms. 1. Check connector contacting status by DOR-230 PCB.
    [Diagram] PORT 1: INA
    PORT 2: INB
    PORT 3: INC
    TCD NO PCB No. PCB Selection S/W Input Port ADDRESS
    80 DOR-230(#1) PORT 1 0x5000 0000
    SW1 2. Check the PCB selection switch status by DOR-230 PCB No..
    PORT 2 0x5000 0400 (Setting should be as same as shown in the left diagram.)
    SW2
    PORT 3 0x5000 0800
    81 DOR-230(#2) PORT 1 0x5000 2000 3. Check the connection status of PCB Connector(MA) cable
    SW1
    PORT 2 0x5000 2400 since there could be an error in PCB connection status and
    SW2 DOR-230 PCB, DOC-200 PCB, or other PCBs.
    PORT 3 0x5000 2800
    82 DOR-230(#3) PORT 1 0x5000 4000
    SW1 4. Visually check defects for input port HIC(MIA-E02) in DOR-230
    PORT 2 0x5000 4400
    SW2 PCB where the error occurs.
    PORT 3 0x5000 4800
    83 DOR-230(#4) PORT 1 0x5000 6000 5. Check the DC +48[V] voltage supplied to external devices(e.g.
    SW1
    PORT 2 0x5000 6400 relay, etc.) which is connected to input port in DOR-230 where
    SW2
    PORT 3 0x5000 6800 the error occurs.

    6. Check the DC +5[V], +15[V], +24[V] voltage for PCB.


    1) Check the voltage applied to DOR-230 PCB.
    (1) DC +5[V] : Connector SMP/1, SMP/6
    (2) DC +15[V] : Connector SMP/2
    (3) DC +24[V] : Connector PWS/1
    (4) GND : TP10(Location : Between Connector INC and OUT)
    2) Check the voltage applied to DOC-230 PCB PCB.
    (1) +5[V] => Connector MG/1, MG/6
    (2) GND => TP16(Location : Just above Connector MG)

    7. If TCD 80 ~ 83 error exists even after above checks,


    1) Try replacing the DOR-230 PCB where the error occurs.
    2) If the error has nothing to do with DOR-230 PCB,
    try replacing DOC-200 PCB.

    You might also like