M54HC86

M74HC86

QUAD EXCLUSIVE OR GATE

. HIGH SPEED

. tPD = 10 ns (TYP.) AT VCC = 5 V

LOW POWER DISSIPATION

. ICC = 1 µA (MAX.) AT TA = 25 °C
HIGH NOISE IMMUNITY

. VNIH = VNIL = 28 % VCC (MIN.)

OUTPUT DRIVE CAPABILITY B1R F1R

. 10 LSTTL LOADS
SYMMETRICAL OUTPUT IMPEDANCE
(Plastic Package) (Ceramic Package)

. IOH = IOL = 4 mA (MIN.)

BALANCED PROPAGATION DELAYS

. tPLH = tPHL
WIDE OPERATING VOLTAGE RANGE M1R C1R

. VCC (OPR) = 2 V TO 6 V
PIN AND FUNCTION COMPATIBLE
WITH 54/74LS86
(Micro Package)
ORDER CODES :
M54HC86F1R M74HC86M1R
(Chip Carrier)

M74HC86B1R M74HC86C1R

PIN CONNECTIONS (top view)

DESCRIPTION
The M54/74HC86 is a high speed CMOS QUAD
EXCLUSIVE OR GATE fabricated in silicon gate
C2MOS technology.
It has the same high speed performance of LSTTL
combined with true CMOS low power consumption.
Input and output buffer are installed, which enables
high noise immunity and stable output.
All inputs are equipped with protection circuits
against static discharge and transient excess volt-
age.

INPUT AND OUTPUT EQUIVALENT CIRCUIT

NC =
No Internal
Connection

December 1992 1/9

M54/M74HC86

TRUTH TABLE IEC LOGIC SYMBOL

A B Y
L L L
L H H
H L H
H H L

PIN DESCRIPTION

PIN No SYMBOL NAME AND FUNCTION

1, 4, 9, 12 1A to 4A Data Inputs
2, 5, 10, 13 1B to 4B Data Inputs
3, 6, 8, 11 1Y to 4Y Data Outputs
7 GND Ground (0V)
14 VCC Positive Supply Voltage

SCHEMATIC CIRCUIT (Per Gate)

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Value Unit
VCC Supply Voltage -0.5 to +7 V
VI DC Input Voltage -0.5 to VCC + 0.5 V
VO DC Output Voltage -0.5 to VCC + 0.5 V
IIK DC Input Diode Current ± 20 mA
IOK DC Output Diode Current ± 20 mA
IO DC Output Source Sink Current Per Output Pin ± 25 mA
ICC or IGND DC VCC or Ground Current ± 50 mA
PD Power Dissipation 500 (*) mW
o
Tstg Storage Temperature -65 to +150 C
o
TL Lead Temperature (10 sec) 300 C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied.
(*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC

2/9
 M54/M74HC86

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Value Unit
VCC Supply Voltage 2 to 6 V
VI Input Voltage 0 to VCC V
VO Output Voltage 0 to VCC V
o
Top Operating Temperature: M54HC Series -55 to +125 C
o
M74HC Series -40 to +85 C
tr, tf Input Rise and Fall Time VCC = 2 V 0 to 1000 ns
VCC = 4.5 V 0 to 500
VCC = 6 V 0 to 400

DC SPECIFICATIONS

Test Conditions Value

Symbol Parameter TA = 25 oC -40 to 85 oC -55 to 125 oC Unit
VCC
54HC and 74HC 74HC 54HC
(V)
Min. Typ. Max. Min. Max. Min. Max.
VIH High Level Input 2.0 1.5 1.5 1.5
Voltage 4.5 3.15 3.15 3.15 V
6.0 4.2 4.2 4.2
V IL Low Level Input 2.0 0.5 0.5 0.5
Voltage 4.5 1.35 1.35 1.35 V
6.0 1.8 1.8 1.8
V OH High Level 2.0 1.9 2.0 1.9 1.9
VI =
Output Voltage 4.5 IO=-20 µA 4.4 4.5 4.4 4.4
VIH
V
6.0 or 5.9 6.0 5.9 5.9
4.5 V IL IO=-4.0 mA 4.18 4.31 4.13 4.10
6.0 IO=-5.2 mA 5.68 5.8 5.63 5.60
VOL Low Level Output 2.0 0.0 0.1 0.1 0.1
VI =
Voltage 4.5 IO= 20 µA 0.0 0.1 0.1 0.1
VIH
V
6.0 or 0.0 0.1 0.1 0.1
4.5 V IL IO= 4.0 mA 0.17 0.26 0.33 0.40
6.0 IO= 5.2 mA 0.18 0.26 0.33 0.40
II Input Leakage VI = VCC or GND ±0.1 ±1 ±1 µA
6.0
Current
ICC Quiescent Supply 6.0 VI = VCC or GND 1 10 20 µA
Current

3/9
M54/M74HC86

AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns)

Test Conditions Value
o
Symbol Parameter TA = 25 C -40 to 85 oC -55 to 125 oC Unit
VCC
54HC and 74HC 74HC 54HC
(V)
Min. Typ. Max. Min. Max. Min. Max.
tTLH Output Transition 2.0 30 75 95 110
tTHL Time 4.5 8 15 19 22 ns
6.0 7 13 16 19
tPLH Propagation 2.0 56 110 140 165
tPHL Delay Time 4.5 14 22 28 33 ns
6.0 12 19 24 28
CIN Input Capacitance 5 10 10 10 pF
CPD (*) Power Dissipation 26
pF
Capacitance
(*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load.
(Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC/4 (per Gate)

SWITCHING CHARACTERISTICS TEST CIRCUIT

TEST CIRCUIT ICC (Opr.)

INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF SWITCHING CHARACTERISTICS TEST.

4/9
 M54/M74HC86

Plastic DIP14 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

a1 0.51 0.020

B 1.39 1.65 0.055 0.065

b 0.5 0.020

b1 0.25 0.010

D 20 0.787

E 8.5 0.335

e 2.54 0.100

e3 15.24 0.600

F 7.1 0.280

I 5.1 0.201

L 3.3 0.130

Z 1.27 2.54 0.050 0.100

P001A

5/9
M54/M74HC86

Ceramic DIP14/1 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

A 20 0.787

B 7.0 0.276

D 3.3 0.130

E 0.38 0.015

e3 15.24 0.600

F 2.29 2.79 0.090 0.110

G 0.4 0.55 0.016 0.022

H 1.17 1.52 0.046 0.060

L 0.22 0.31 0.009 0.012

M 1.52 2.54 0.060 0.100

N 10.3 0.406

P 7.8 8.05 0.307 0.317

Q 5.08 0.200

P053C

6/9
 M54/M74HC86

SO14 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A 1.75 0.068
a1 0.1 0.2 0.003 0.007
a2 1.65 0.064
b 0.35 0.46 0.013 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.019
c1 45° (typ.)
D 8.55 8.75 0.336 0.344
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 7.62 0.300
F 3.8 4.0 0.149 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.019 0.050
M 0.68 0.026
S 8° (max.)

P013G

7/9
M54/M74HC86

PLCC20 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

A 9.78 10.03 0.385 0.395

B 8.89 9.04 0.350 0.356

D 4.2 4.57 0.165 0.180

d1 2.54 0.100

d2 0.56 0.022

E 7.37 8.38 0.290 0.330

e 1.27 0.050

e3 5.08 0.200

F 0.38 0.015

G 0.101 0.004

M 1.27 0.050

M1 1.14 0.045

P027A

8/9
 M54/M74HC86

Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.

 1994 SGS-THOMSON Microelectronics - All Rights Reserved

SGS-THOMSON Microelectronics GROUP OF COMPANIES

Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands -
Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A

9/9