M54/74HC125

M54/74HC126

QUAD BUS BUFFERS (3-STATE)

. HIGH SPEED

. tPD = 8 ns (TYP.) AT VCC = 5 V

LOW POWER DISSIPATION

. ICC = 4 µA (MAX.) AT 25 °C
OUTPUT DRIVE CAPABILITY

. 15 LSTTL LOADS
BALANCED PROPAGATION DELAYS B1R F1R

. tPLH = tPHL
SYMMETRICAL OUTPUT IMPEDANCE
(Plastic Package) (Ceramic Package)

. IOL = IOH = 6 mA (MIN.)

HIGH NOISE IMMUNITY

. VNIH = VNIL = 28 % VCC (MIN.)

WIDE OPERATING VOLTAGE RANGE M1R C1R

. VCC (OPR) = 2 V TO 6 V
PIN AND FUNCTION COMPATIBLE
WITH 54/74LS125/126
(Micro Package)
ORDER CODES :
M54HCXXXF1R M74HCXXXM1R
(Chip Carrier)

M74HCXXXB1R M74HCXXXC1R

DESCRIPTION
The M54/74HC125/126 are high speed CMOS PIN CONNECTIONS (top view)
QUAD BUS BUFFER (3-STATE) FABRICATED IN
SILICON GATE C2MOS technology. HC125
They have the same high speed performance of
LSTTL combined with true CMOS low power con-
sumption.
These devices require the same 3-STATE control
input G to be taken high to make the output go into
the high impedance state.
All inputs are equipped with protection circuits
against static discharge and transient excess volt-
age.

INPUT AND OUTPUT EQUIVALENT CIRCUIT

HC126

NC =
No Internal
Connection

September 1993 1/11

M54/M74HC125/126

CHIP CARRIER

HC125 HC126

TRUTH TABLE (HC125) TRUTH TABLE (HC126)

A G Y A G Y
X H Z X L Z
L L L L H L
H L H H H H

PIN DESCRIPTION (HC125) PIN DESCRIPTION (HC126)

PIN No SYMBOL NAME AND FUNCTION PIN No SYMBOL NAME AND FUNCTION
1, 4, 10, 13 G1 to G4 Output Enable Input 1, 4, 10, 13 G1 to G4 Output Enable Input
2, 5, 9, 12 A1 to A4 Data Inputs 2, 5, 9, 12 A1 to A4 Data Inputs
3, 6, 8, 11 Y1 to Y4 Data Outputs 3, 6, 8, 11 Y1 to Y4 Data Outputs
7 GND Ground (0V) 7 GND Ground (0V)
14 VCC Positive Supply Voltage 14 VCC Positive Supply Voltage

IEC LOGIC SYMBOLS

HC125 HC126

2/11
 M54/M74HC125/126

CIRCUIT DIAGRAM

HC125 HC126

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Value Unit
VCC Supply Voltage -0.5 to +7 V
VI DC Input Voltage -0.5 to VCC + 0.5 V
VO DC Output Voltage -0.5 to VCC + 0.5 V
IIK DC Input Diode Current ± 20 mA
IOK DC Output Diode Current ± 20 mA
IO DC Output Source Sink Current Per Output Pin ± 35 mA
ICC or IGND DC VCC or Ground Current ± 70 mA
PD Power Dissipation 500 (*) mW
o
Tstg Storage Temperature -65 to +150 C
o
TL Lead Temperature (10 sec) 300 C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied.
(*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Value Unit
VCC Supply Voltage 2 to 6 V
VI Input Voltage 0 to VCC V
VO Output Voltage 0 to VCC V
o
Top Operating Temperature: M54HC Series -55 to +125 C
o
M74HC Series -40 to +85 C
tr, tf Input Rise and Fall Time VCC = 2 V 0 to 1000 ns
VCC = 4.5 V 0 to 500
VCC = 6 V 0 to 400

3/11
M54/M74HC125/126

DC SPECIFICATIONS
Test Conditions Value
Symbol Parameter TA = 25 oC -40 to 85 oC -55 to 125 oC Unit
VCC
54HC and 74HC 74HC 54HC
(V)
Min. Typ. Max. Min. Max. Min. Max.
VIH High Level Input 2.0 1.5 1.5 1.5
Voltage 4.5 3.15 3.15 3.15 V
6.0 4.2 4.2 4.2
V IL Low Level Input 2.0 0.5 0.5 0.5
Voltage 4.5 1.35 1.35 1.35 V
6.0 1.8 1.8 1.8
V OH High Level 2.0 1.9 2.0 1.9 1.9
VI =
Output Voltage 4.5 IO=-20 µA 4.4 4.5 4.4 4.4
VIH
V
6.0 or 5.9 6.0 5.9 5.9
4.5 V IL IO=-6.0 mA 4.18 4.31 4.13 4.10
6.0 IO=-7.8 mA 5.68 5.8 5.63 5.60
VOL Low Level Output 2.0 0.0 0.1 0.1 0.1
VI =
Voltage 4.5 IO= 20 µA 0.0 0.1 0.1 0.1
VIH
V
6.0 or 0.0 0.1 0.1 0.1
4.5 V IL IO= 6.0 mA 0.17 0.26 0.33 0.40
6.0 IO= 7.8 mA 0.18 0.26 0.33 0.40
II Input Leakage VI = VCC or GND ±0.1 ±1 ±1 µA
6.0
Current
IOZ 3 State Output VI = VIH or VIL ±0.5 ±5 ±10 µA
6.0
Off-state Current VO = VCC or GND
ICC Quiescent Supply 6.0 VI = VCC or GND 4 40 80 µA
Current

4/11
 M54/M74HC125/126

AC ELECTRICAL CHARACTERISTICS (Input t r = t f = 6 ns)

Test Conditions Value
Symbol Parameter TA = 25 oC -40 to 85 oC -55 to 125 oC Unit
VCC CL
54HC and 74HC 74HC 54HC
(V) (pF)
Min. Typ. Max. Min. Max. Min. Max.
tTLH Output Transition 2.0 20 60 75 90
tTHL Time 4.5 50 6 12 15 18 ns
6.0 5 10 13 15
tPLH Propagation 2.0 36 75 95 110
tPHL Delay Time 4.5 50 9 15 19 22 ns
6.0 8 13 16 19
2.0 52 105 130 160
4.5 150 13 21 26 32 ns
6.0 11 18 22 27
tPZL 3 State Output 2.0 36 75 95 110
tPZH Enable Time 4.5 50 RL = 1 KΩ 9 15 19 22 ns
6.0 8 13 16 19
2.0 52 105 130 160
4.5 150 RL = 1 KΩ 13 21 26 32 ns
6.0 11 18 22 27
tPLZ 3 State Output 2.0 48 80 100 120
tPHZ Disable Time 4.5 50 RL = 1 KΩ 12 16 20 24 ns
6.0 10 14 17 20
CIN Input Capacitance 5 10 10 10 pF
CPD (*) Power Dissipation 35
pF
Capacitance
(*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load.
(Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC

SWITCHING CHARACTERISTICS TEST WAVEFORM

HC125

A
G G

Y
Y Y

HC126

5/11
M54/M74HC125/126

TEST CIRCUIT ICC (Opr.)

HC125

THE OTHER INPUTS ARE CONNECTED TO VCC LINE OR GND LINE

HC126

THE OTHER INPUTS ARE CONNECTED TO VCC LINE OR GND LINE

6/11
 M54/M74HC125/126

Plastic DIP14 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

a1 0.51 0.020

B 1.39 1.65 0.055 0.065

b 0.5 0.020

b1 0.25 0.010

D 20 0.787

E 8.5 0.335

e 2.54 0.100

e3 15.24 0.600

F 7.1 0.280

I 5.1 0.201

L 3.3 0.130

Z 1.27 2.54 0.050 0.100

P001A

7/11
M54/M74HC125/126

Ceramic DIP14/1 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

A 20 0.787

B 7.0 0.276

D 3.3 0.130

E 0.38 0.015

e3 15.24 0.600

F 2.29 2.79 0.090 0.110

G 0.4 0.55 0.016 0.022

H 1.17 1.52 0.046 0.060

L 0.22 0.31 0.009 0.012

M 1.52 2.54 0.060 0.100

N 10.3 0.406

P 7.8 8.05 0.307 0.317

Q 5.08 0.200

P053C

8/11
 M54/M74HC125/126

SO14 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A 1.75 0.068
a1 0.1 0.2 0.003 0.007
a2 1.65 0.064
b 0.35 0.46 0.013 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.019
c1 45° (typ.)
D 8.55 8.75 0.336 0.344
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 7.62 0.300
F 3.8 4.0 0.149 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.019 0.050
M 0.68 0.026
S 8° (max.)

P013G

9/11
M54/M74HC125/126

PLCC20 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

A 9.78 10.03 0.385 0.395

B 8.89 9.04 0.350 0.356

D 4.2 4.57 0.165 0.180

d1 2.54 0.100

d2 0.56 0.022

E 7.37 8.38 0.290 0.330

e 1.27 0.050

e3 5.08 0.200

F 0.38 0.015

G 0.101 0.004

M 1.27 0.050

M1 1.14 0.045

P027A

10/11
 M54/M74HC125/126

Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.

 1994 SGS-THOMSON Microelectronics - All Rights Reserved

SGS-THOMSON Microelectronics GROUP OF COMPANIES

Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands -
Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A

11/11