MITSUBISHI<Dig./Ana.

INTERFACE>

M62030FP
VOLTAGE DETECTING, SYSTEM RESETTING IC SERIES

GENERAL DESCRIPTION
The M62030FP is a voltage threshold detector designed for PIN CONFIGURATION (TOP VIEW)
detection of an input voltage/supply voltage and generation of
a system reset pulse for almost all logic circuits such as
microcontroller.
It contains a delay circuit which provides 200µs (typ) delay
and 4 modes of delays [25ms, 50ms, 100ms, 200ms (typ)] in
the input voltage detection type and in the supply voltage
detection type, respectively.
Ct0 1 8 VRES

M62030FP
FEATURES
VIN 2 7 Vcc
• Built-in 2 functional circuits for detecting voltage
• Built-in delay circuit to provide long delay time Ct1 3 6 OUT1
(without external delay capacitors)
• Selectable 4 modes of delay time GND 4 5 OUT2
[25msec, 50msec, 100msec, 200msec(typ)]
• Few external components
• Small 8-pin SOP package

APPLICATION Outline 8P2S-A

• Reset circuits of MCU, MPU and logics

RECOMMEND OPERATING CONDITION

• Supply voltage range ………… 2V to 10V

BLOCK DIAGRAM Vcc

7
Vcc Vcc

6 OUT1

VIN 2
1.25V

Vcc Vcc

Vcc
5 OUT2
FREQUENCY
OSCILLATOR DIVIDER

1.25V MULTIPLEXER

VRES 8
3 Ct1

1 Ct0
4
GND

( 1/ 5 )
 MITSUBISHI<Dig./Ana. INTERFACE>

M62030FP
VOLTAGE DETECTING, SYSTEM RESETTING IC SERIES

ABSOLUTE MAXIMUM RATINGS (Ta=25°C, unless otherwise noted)

Symbol Parameter Conditions Ratings Unit
Vcc Supply voltage -0.3 to 10 V
I SINK 1,2 Output Sink Current Output1,2 8.0 mA
VO Output voltage -0.3 to 10 V
V RES Self reset input voltage -0.3 to 10 V
Pd Power dissipation 300 mW
Ktheta Thermal Derating Ta ≥ 25°C 3.0 mW/°C
Topr Operating temperature -20 to 75 °C
Tstg Storage temperature -40 to 125 °C

ELECTRICAL CHARACTERISTICS (Ta = -20 to 75°C, unless otherwise noted)

< Reset circuit 1 >
Limits
Symbol Parameter Test Conditions Unit
Min Typ Max
V S1 Detecting voltage 1 Ta= 25°C 1.20 1.25 1.30 V
∆Vs1 Hysteresis voltage 1 Ta= 25°C 9 15 23 mV
TPLH 1 Output "L to H" propagation delay time 1 CL=100pF,Ta= 25°C 80 200 500 µs
V OL 1 Low output voltage 1 VIN<1.2V, IOL=5mA, Vcc=5V 0.2 0.4 V
Vcc ≤ 7V -0.3 Vcc
V
V IN Input voltage
Vcc > 7V -0.3 7.0
I IN Input Current VIN=1.25V 100 500 nA

< Reset circuit 2 >

Limits
Symbol Parameter Test Conditions Unit
Min Typ Max
V S2 Detecting voltage 2 Ta= 25°C 4.0 4.2 4.4 V
∆VS2 Hysteresis voltage 2 Ta= 25°C 30 50 100 mV
Ct0 ="L", Ct1="H" 25 ms
T PLH2 Output "L to H" propagation delay time 2 Ct0 ="H", Ct1="L" CL=100pF 50 ms
Ct0 ="H", Ct1="H" or opening Ta= 25°C 100 ms
Ct0="L",Ct1="L" 200 ms
V OL 2 Low output voltage 2 Vcc=4.0V,IOL=5mA 0.2 0.4 V
V RESH Input High voltage Ta= 25°C 2 Vcc V
Self
I RESH Ta= 25°C µA
Reset Input High current VRES=2V 80
V RESL Input Low voltage Ta= 25°C -0.3 0.8 V
V Ct0,1H Input High voltage Ta= 25°C 1.4 V
V Ct0,1L Ct0 Input Low voltage Ta= 25°C 0.6 V
I Ct0,1H Ct1 Input High current Ta= 25°C 75 µA
I Ct0,1L Input Low current Ta= 25°C 75 µA

( 2/ 5)
 MITSUBISHI<Dig./Ana. INTERFACE>

M62030FP
VOLTAGE DETECTING, SYSTEM RESETTING IC SERIES

ELECTRICAL CHARACTERISTICS (Ta = -20 to 75°C,unless otherwise noted)

< Common specification >

Limits
Symbol Parameter Test Conditions Unit
Min Typ Max
Vcc Supply Voltage 2 10 V
Icc1 Circuit Current in OFF Vcc=5V 1.0 2.0 mA
Icc2 Circuit Current in ON Both circuit "ON" state. Contain pull-up resistor 2.0 4.0 mA
Vs/∆T Detecting Voltage Temperature Coefficient 0.01 %/°C
∆Vs/∆T The hysteresis voltage temperature coefficient 0.01 %/°C
TPLH/∆T Propagation delay time temperature coefficient 0.10 %/°C
V OH Output High Voltage I OH = -40µA Vcc-0.6 Vcc-0.4 Vcc-0.2 V
TPHL Output "H to L" propagation delay time CL = 100pF 10 µs
V OPL *1 Threshold Operating Voltage Ta = 25°C 0.67 0.8 V
R Built-in pull-up resistor 5 10 15 kΩ
Note*1: Minimum supply voltage to keep output low

PIN DESCRIPTION

Terminal No. Symbol Functional Description

Setting delay time. 25ms 50ms 100ms 200ms
1 Ct0 It is possible to set 4 kinds of delay Ct0 L H H L
times by inputting "H" or "L" into
Ct1 H L H L
3 Ct1 these two terminal.

2 VIN Detecting voltage input

4 GND Ground
6 OUT1 Output terminal 1 (Delay time 200µs settlement output)
5 OUT2 Output terminal 2 (Delay time variable type output)
7 Vcc Supply voltage
It outputs "L"and "H" to OUT2 terminal when the VRES input is "H" and "L", respectively.
8 VRES

( 3/ 5 )
 MITSUBISHI<Dig./Ana. INTERFACE>

M62030FP
VOLTAGE DETECTING, SYSTEM RESETTING IC SERIES

FUNCTION DIAGRAM

INPUT SUPPLY
VOLTAGE VOLTAGE
1.25V 4.20V

t t
OUTPUT 1 OUTPUT 2

H H
TPLH1 TPLH2
L L

t t
Input voltage detecting type Supply voltage detecting type

EXAMPLE OF APPLICATION CIRCUIT

1) The application to microprocessor system

Note 1. The Input voltage detection type can be used as the voltage supervisor of microprocessor system
like the following circuit.
In this case, a detection power supply voltage is approximately 1.25 x (R1+R2)/ R2 (v).
The detecting supply voltage can be set between 2V and 10V.

Note 2. The detecting voltage can be adjusted by changing R1 and/or R2 in the following circuit.
The detection accuracy is ±4%.

Note 3. It has a delay capacitor and the delay time is about 200µs.

Vcc

SUPPLY
VOLTAGE
R1 7
Vcc

2 VIN OUT2 5 RESET(RESET)

M62030FP MCU
R2 8 VRES OUT1 6
Ct0 Ct1 GND
1 3 4 GND

(4/ 5)
 MITSUBISHI<Dig./Ana. INTERFACE>

M62030FP
VOLTAGE DETECTING, SYSTEM RESETTING IC SERIES

2) The Variable setup time type

Note 1. A delay time of the supply voltage detection type can be set to one among 25ms, 50ms, 100ms and
200ms by the combination of pin 1 and pin 3.

Vcc

SUPPLY
7 VOLTAGE
R1
Vcc
2 VIN OUT2 5 RESET(RESET)

M62030FP MCU
R2 8 VRES OUT1 6
Ct0 Ct1 GND
1 3 4 GND
The other system reset

! Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but
there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury,
fire or property damage. Remember to give due consideration to safety when making your circuit design,in order to prevent
fires from spreading, redundancy, malfunction or other mishap.

( 5/ 5 )
This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.