INTEGRATED CIRCUITS

74F3037
Quad 2-input NAND 30Ω driver

Product specification 1990 Feb 09

IC15 Data Handbook


 
 
Philips Semiconductors Product specification

Quad 2-input NAND 30Ω driver 74F3037

FEATURES transmission line effects of PC boards which appear when

• 30Ω line driver fast edge rates are used.
• 67mA output drive capability in the high state The drive capability of the 74F3037 is 67mA source and
• High speed 160mA sink with a VCC as low as 4.5V. This guarantees
incident wave switching with VOH not less than 2.0V and VOL
• Facilitates incident wave switching not more than 0.8mA while driving impedances as low as 30
• 3nh lead inductance each on VCC and GND when both ohms. This is applicable with any combination of outputs
side pins are used using continuous duty. The propagation delay of the part is
• 160mA output drive capability in the low state minimally affected by reflections when terminated only by
• Industrial temperature range available (–40°C to +85°C) the TTL inputs of other devices. Performances may be
improved by full or partial line termination.
DESCRIPTION
The 74F3037 is a high current line driver composed of four TYPE TYPICAL TYPICAL SUPPLY
2–input NAND gates. It has been designed to deal with the PROPAGATION DELAY CURRENT( TOTAL)
74F3037 2.0ns 16mA

ORDERING INFORMATION
ORDER CODE
COMMERCIAL RANGE INDUSTRIAL RANGE
DESCRIPTION VCC = 5V ±10%, VCC = 5V ±10%, PKG DWG #
Tamb = 0°C to +70°C Tamb = –40°C to +85°C
16–pin plastic DIP N74F3037N I74F3037N SOT38-4
16–pin plastic SOL N74F3037D I74F3037D SOT162-1

INPUT AND OUTPUT LOADING AND FAN OUT TABLE

PINS DESCRIPTION 74F (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW
Dna, Dnb Data inputs 1.0/1.0 20µA/0.6mA

Qn Data output 3350/266 67mA/160mA

Note to input and output loading and fan out table
One (1.0) FAST unit load is defined as: 20µA in the high state and 0.6mA in the low state.

LOGIC DIAGRAM FUNCTION TABLE

D0a
1 INPUTS OUTPUT
3
Q0
D0b 2 Dna Dnb Qn
7
D1a 6 L L H
8 Q1
D1b
L H H
10
D2a 9 H L H
11 Q2
D2b
H H L
14
D3a 16 Q3
D3b
15 Notes to function table
VCC = Pin 12,13 H = High voltage level
GND = Pin 4, 5
SF00569 L = Low voltage level

February 9, 1990 2 853 0021 98744

Philips Semiconductors Product specification

Quad 2-input NAND 30Ω driver 74F3037

PIN CONFIGURATION IEC/IEEE SYMBOL

D0a 1 16 Q3 1 &
3
2
D0b 2 15 D3b

Q0 3 14 D3a 7
6
8
GND 4 13 VCC

GND 5 12 VCC 10
9
11
Q1 6 11 D2a

D1a 7 10 D2b 14
15 16
D1b 8 9 Q2

SF00570 SF00572

LOGIC SYMBOL

1 2 7 8 10 11 14 15

D0a D0b D1a D1a D2a D2b D3a D3b

Q0 Q1 Q2 Q3

VCC = Pin 12,13 3 6 9 16

GND = Pin 4, 5
SF00571

ABSOLUTE MAXIMUM RATINGS

(Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the
operating free air temperature range.)
SYMBOL PARAMETER RATING UNIT
VCC Supply voltage –0.5 to +7.0 V
VIN Input voltage –0.5 to +7.0 V
IIN Input current –30 to +5 mA
VOUT Voltage applied to output in high output state –0.5 to VCC V
IOUT Current applied to output in low output state 320 mA

Tamb Operating free air temperature range Commercial range 0 to +70 °C

Industrial range –40 to +85 °C
Tstg Storage temperature range –65 to +150 °C

February 9, 1990 3
Philips Semiconductors Product specification

Quad 2-input NAND 30Ω driver 74F3037

RECOMMENDED OPERATING CONDITIONS

SYMBOL PARAMETER LIMITS TA =
–40 to
UNIT MIN NOM MAX
+85°C
VCC Supply voltage 4.5 5.0 5.5 V
VIH High–level input voltage 2.4 V
VIL Low–level input voltage 0.8 V
IIk Input clamp current –18 mA
IOH High–level output current –67 mA
IOL Low–level output current 160 mA
Tamb Operating free air temperature range Commercial range 0 +70 °C
Industrial range –40 +85 °C

DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
SYMBOL PARAMETER TEST LIMITS UNIT
CONDITIONS1 MIN TYP2 MAX
VCC = MIN, IOH = –45mA ±10%VCC 2.5 V

VOH High–level output voltage VIL = MAX, ±5%VCC 2.7 V

IOH1 =
VIH = MIN
–67mA3
±10%VCC 2.0 V

VCC = MIN, VIL =

VOL Low–level output voltage
MAX,
IOL = 100mA ±10%VCC 0.30 0.50 V

IOL1 =
VIH = MIN
160mA4
±5%VCC 0.30 0.50 V

VIK Input clamp voltage VCC = MIN, II = IIK -0.73 -1.2 V

II Input current at maximum input voltage VCC = MAX, VI = 7.0V 100 µA
IIH High–level input current VCC = MAX, VI = 2.7V 20 µA
IIL Low–level input current VCC = MAX, VI = 0.5V -0.6 mA
IO Output current5 VCC = MAX, VO = 2.25V -100 -200 mA
ICC Supply current (total) ICCH VCC = MAX 6.0 9.0 mA
ICCL 30
mA 40
Notes to DC electrical characteristics
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at VCC = 5V, Tamb = 25°C.
3. IOH1 is the current necessary to guarantee the low to high transition in a 30 ohm transmission line on the incident wave.
4. IOL1 is the current necessary to guarantee the high to low transition in a 30 ohm transmission line on the incident wave.
5. IO is tested under conditions that produce current approximately one half of the true short–circuit current (IOS).

AC ELECTRICAL CHARACTERISTICS
LIMITS
Tamb = +25°C Tamb = 0°C to +70°C Tamb =–40°C to +85°C
SYMBOL PARAMETER TEST VCC = +5.0V VCC = +5.0V ± 10% VCC = +5.0V ± 10% UNIT
CONDITION CL = 50pF, CL = 50pF, CL = 50pF,
RL = 500Ω RL = 500Ω RL = 500Ω
MIN TYP MAX MIN MAX MIN MAX
tPLH Propagation delay 1.0 2.0 5.0 1.0 5.5 1.0 5.5
Waveform 1 ns
tPHL Dna, Dnb to Qn 1.0 2.0 4.5 1.0 5.0 1.0 5.0

February 9, 1990 4
Philips Semiconductors Product specification

Quad 2-input NAND 30Ω driver 74F3037

AC WAVEFORMS

Dna, Dnb
VM VM

tPHL tPLH

VM VM
Qn

SF00005

Waveform 1. Propagation delay for inverting outputs

Note to AC waveforms
For all waveforms, VM = 1.5V.

TEST CIRCUIT AND WAVEFORMS

VCC tw AMP (V)

90% 90%
NEGATIVE
VM VM
PULSE
10% 10%
VIN VOUT 0V
PULSE D.U.T.
GENERATOR tTHL (tf ) tTLH (tr )

RT CL RL tTLH (tr ) tTHL (tf )

AMP (V)
90% 90%
POSITIVE
PULSE VM VM

Test Circuit for Totem-Pole Outputs 10% 10%

tw 0V

DEFINITIONS: Input Pulse Definition

RL = Load resistor;
see AC ELECTRICAL CHARACTERISTICS for value. INPUT PULSE REQUIREMENTS
CL = Load capacitance includes jig and probe capacitance; family
see AC ELECTRICAL CHARACTERISTICS for value. amplitude VM rep. rate tw tTLH tTHL
RT = Termination resistance should be equal to ZOUT of
74F 3.0V 1.5V 1MHz 500ns 2.5ns 2.5ns
pulse generators.

SF00006

February 9, 1990 5
Philips Semiconductors Product specification

Quad 2-input NAND 30Ω driver 74F3037

DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4

1990 Feb 09 6
Philips Semiconductors Product specification

Quad 2-input NAND 30Ω driver 74F3037

SO16: plastic small outline package; 16 leads; body width 7.5 mm SOT162-1

1990 Feb 09 7
Philips Semiconductors Product specification

Quad 2-input NAND 30Ω driver 74F3037

Data sheet status

Data sheet Product Definition [1]
status status

Objective Development This data sheet contains the design target or goal specifications for product development.
specification Specification may change in any manner without notice.

Preliminary Qualification This data sheet contains preliminary data, and supplementary data will be published at a later date.
specification Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
Product Production This data sheet contains final specifications. Philips Semiconductors reserves the right to make
specification changes at any time without notice in order to improve design and supply the best possible product.

[1] Please consult the most recently issued datasheet before initiating or completing a design.

Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.

Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.

Philips Semiconductors  Copyright Philips Electronics North America Corporation 1998

811 East Arques Avenue All rights reserved. Printed in U.S.A.
P.O. Box 3409
Sunnyvale, California 94088–3409 print code Date of release: 10-98
Telephone 800-234-7381
Document order number: 9397-750-05203


 
 
yyyy mmm dd 8
This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.