ZIV ZLV V3.70 Line PTT User Manual ENU

OMICRON PTL ZIV ZLV V3.
70 Line PTT User Manual
OMICRON PTL
ZIV ZLV V3.70 Line PTT
User Manual
V1.100
© OMICRON electronics GmbH 1/5

OMICRON PTL ZIV ZLV V3.70 Line PTT User Manual
Content
1. General .............................................................................................................................................3
2. Software and Hardware Requirements............................................................................................3
3. Hardware ..........................................................................................................................................4
4. Functional Range .............................................................................................................................4
5. XRIO Converter ................................................................................................................................5
6. Specific Protection Tests .................................................................................................................5
6.1 Close-Onto-a-Fault ..........................................................................................................................5
6.1.1 Manual Close/External Manual Close.........................................................................................5

1. General
This user manual describes details of testing ZIV ZLV relay with the OMICRON Protection Test Template.
General information on the usage of OMICRON Protection Testing Library items can be found in the
OMICRON PTL user manual.
The template has been tested with the following relay:

Manufacturer: ZIV
Model: ZLV
Software Version: V 03.70.0
2. Software and Hardware Requirements

To use this template, you must have a valid test license for the OMICRON Test Universe 3.20 software or
higher versions and the following test modules:
• Control Center
• Quick CMC
• Overcurrent
• State Sequencer
• Advanced Distance
Any CMC test set can be used with this Protection Test Template.

3. Hardware
There are multiple possibilities of wiring ZIV ZLV relay to a CMC test set. The advised connections are
shown in Figure 1. These connections are the default settings in the Hardware Configuration of the PTT.
Connection diagram for ZIV ZLV Line
VC
VN
VA
VB
IN
IC
IA
IB
CB aux (52a)
CB aux (52b)
Trip
Manual close
Start
Figure 1: Connection for ZIV ZLV
4. Functional Range
Supported functions:
• Distance Protection (21/21N) (MHO/Quad/MHO or Quad zones 1-5 for Standard Protection
Scheme “Step Distance”)
• Load Encroachment (ph-ph)
• Load Encroachment (ph-gnd only with the same k0 Factor for all zones) (21)
• Close-Onto-Fault Detector (50SOF)
• Back-up Overcurrent Protection (50F/51F), (50N/51N)
Not supported parameters:
• Distance Characteristic = Quad and Mho

• Tilt Angle Type = Calculated
• t Tilt < t Z1LL + Min Operate Time

Not supported functions:
• VT Fuse Failure Detector

• Open Pole Detector
• Dead Line Detector
• Power-Swing Detector
• Remote Breaker Open Detector
• Fault Locator
• Directional Overcurrent Protection
• Stub Bus Protection
• Thermal Image Unit
• Voltage Protection
• Frequency Protection
• Breaker Failure Unit
• Synchronism Unit
• Pole Discordance Detector
• Recloser
The Relay Parameter Section of the XRIO Converter includes only protection parameters of supported
functions.
5. XRIO Converter
The Test Object contains ZIV ZLV XRIO Converter, which includes setting parameters of the modelled
protection relay. The setting parameters are built as an image of the ZivercomPlus V1.67 software.
The Relay Parameter Sections should be filled manually.
6. Specific Protection Tests

In this chapter the specific protection tests, which are not covered by the OMICRON PTL User Manual,
are described.
6.1 Close-Onto-a-Fault
For testing Close-Onto-a-Fault (COF), the State Sequencer test module is used.
6.1.1 Manual Close/External Manual Close

The State Sequencer test module contains 9 states:
1. Dead Line 1: A dead line is simulated
2. Manual Close Command 1: This state is waiting for a manual close command, which has to be
connected to the binary input 5 of the CMC
3. Line Energized 1: An energized line with rated voltage and rated current is simulated for a
duration shorter than the COF enabled time
4. Fault 1 (with COF): A three phase fault is simulated at the end of the COF Supervision Zone (85%
of the zone reach)
5. Dead Line 2: A dead line is simulated
6. Manual Close Command 2: This state is waiting for a manual close command, which has to be
connected to the binary input 5 of the CMC
7. Line Energized 2: An energized line with rated voltage and rated current is simulated for a
duration longer than the COF enabled time
8. Fault 2 (without COF): A three phase fault is simulated at the end of the COF Supervision Zone
(85% of the zone reach)
9. Postfault

ZIV ZLV V3.70 Line PTT User Manual ENU

Uploaded by

Copyright:

Available Formats

ZIV ZLV V3.70 Line PTT User Manual ENU

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ZIV ZLV V3.70 Line PTT User Manual ENU

Uploaded by

Copyright:

Available Formats

OMICRON PTL ZIV ZLV V3.

70 Line PTT User Manual

ZIV ZLV V3.70 Line PTT

© OMICRON electronics GmbH 1/5

© OMICRON electronics GmbH 2/5

The template has been tested with the following relay:

2. Software and Hardware Requirements

© OMICRON electronics GmbH 3/5

Connection diagram for ZIV ZLV Line

Figure 1: Connection for ZIV ZLV

Not supported parameters:

• Distance Characteristic = Quad and Mho

© OMICRON electronics GmbH 4/5

Not supported functions:

• VT Fuse Failure Detector

The Relay Parameter Sections should be filled manually.

6. Specific Protection Tests

6.1.1 Manual Close/External Manual Close

© OMICRON electronics GmbH 5/5

You might also like