Weg CFW300

Motors | Automation | Energy | Transmission & Distribution | Coatings
Frequency Inverter
CFW300 V3.0X
Programming Manual
Programming Manual
Series: CFW300
Language: English
Document: 10007849716 / 02
Software version: 3.0X
Build 528
Publication Date: 10/2020

SUMMARY OF REVISIONS
The information below describes the reviews made in this manual.
Version Revision Description

2.0X R00 First edition.
General revision.
2.1X R01 Change of P695.
Inclusion of the Ethernet Communication Interface (Modbus TCP Protocol).
General revision.
New parameters P191, P760, P761, P762, P763, P764, P765.
3.0X R02 New options in the range of parameter values: P263 to P270, P310 and P312.
Inclusion of the EtherNet/IP and BACnet Protocols.
Firmware update via WPS.
SUMMARY
0 QUICK REFERENCE OF PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-1
1 QUICK REFERENCE OF ALARMS AND FAULTS . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2 SAFETY NOTICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2.1 SAFETY NOTICES IN THIS MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 SAFETY NOTICES ON THE PRODUCT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.3 PRELIMINARY RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
3 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.1 TERMINOLOGY AND DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1.1 Terms and Definitions Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1.2 Numerical Representation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.1.3 Symbols to Describe Parameter Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
4 ABOUT THE HMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.1 USE OF THE HMI TO OPERATE THE INVERTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.2 INDICATIONS ON THE HMI DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.3 OPERATING MODES OF THE HMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
5 HMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.1 ACCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.2 INDICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
6 FREQUENCY INVERTER IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

6.1 INVERTER MODEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.2 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
7 COMMAND AND REFERENCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

7.1 REFERENCE SOURCE SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.2 SPEED REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
8 MOTOR CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

8.1 COMMON FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
8.1.1 Ramps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
8.1.2 Regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
8.1.2.1 DC Link Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
8.1.2.1.1 DC Link Voltage Limitation by “Ramp Hold” (P150 = 0 or 2) . . . . . . . . . . . 8-3
8.1.2.1.2 DC Link Voltage Limitation by “Accelerate Ramp” (P150 = 1 or 3). . . . 8-4
8.1.2.2 Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
8.1.2.2.1 Output Current Limitation by “Ramp Hold” (P150 = 2 or 3) . . . . . . . . . . . . 8-7
8.1.2.2.2 Current Limitation Type “Decelerate Ramp” (P150 = 0 or 1) . . . . . . . . . . . 8-7
8.1.2.3 Switching Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
8.1.3 Flying Start / Ride-Through . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
8.1.4 DC Braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. -10
8.1.5 Dynamic Braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. -12
8.1.6 Skip Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. -13
8.1.7 Fire Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. -14
8.1.8 Control Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. -16
8.2 V/F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-18
8.2.1 Energy Saver (EOC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. -24
8.3 VVW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-26
SUMMARY
9 I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
9.1 ANALOG INPUTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
9.2 EXTERNAL TEMP. SENSOR INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
9.3 SIGNAL POTENTIOMETER INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
9.4 ANALOG OUTPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
9.5 FREQUENCY INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-10
9.6 DIGITAL INPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-11
9.7 INPUT FOR INFRARED RECEIVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-20
9.8 ENCODER INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-20
9.9 DIGITAL OUTPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-22
10 FAULTS AND ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

. 0-1
10.1 FAULT HISTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-1
10.2 FAULT CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-2
10.3 PROTECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-3
10.3.1 Inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 0-3
10.3.1.1 DC Link Voltage Supervision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-3 .
10.3.1.2 Temperature control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-3 .
10.3.2 Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 0-3
11 READ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. 1-1
12 COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. 2-1
12.1 COMMANDS AND COMMUNICATION STATUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-1
12.2 SERIAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-2
12.3 BLUETOOTH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-3
12.4 BACNET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-4
12.5 CANOPEN AND DEVICENET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-5
12.6 PROFIBUS DP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-7
12.7 ETHERNET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-9
13 SOFTPLC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. 3-1
13.1 COMMAND AND STATUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-1
13.2 USER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-2
14 APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. 4-1
14.1 PID CONTROLLER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-1
14.1.1 Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 4-3
14.1.2 Academic PID Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 4-5
14.1.3 Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 4-5
14.1.4 Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-14 ..
15 APPLICATION EXAMPLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. 5-1
15.1 ANALOG INPUT APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-1
15.1.1 Application 1 - Nominal speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 5-2
15.1.2 Application 2 - Overspeed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 5-3
15.1.3 Application 3 - Forward/Reverse using Analog Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 5-4
15.1.4 Application 4 - Analog input with dead zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 5-5
15.1.5 Application 5 - Reverse reference with Analog input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 5-6
15.2 PID CONTROLLER APPLICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-7
QUICK REFERENCE OF PARAMETERS
0 QUICK REFERENCE OF PARAMETERS 0
Param. Description Adjustable Range Factory Setting Prop. Page

P000 Access to Parameters 0 to 9999 1 5-1
P001 Speed Reference 0 to 9999 ro 11-1
P002 Output Speed (Motor) 0 to 9999 ro 11-1
P003 Motor Current 0.0 to 40.0 A ro 11-1
P004 DC Link Voltage 0 to 828 V ro 11-1
P005 Output Frequency (Motor) 0.0 to 400.0 Hz ro 11-1
P006 Inverter Status 0 = Ready ro 11-2
1 = Run
2 = Undervoltage
3 = Fault
4 = Self-Tuning
5 = Configuration
6 = DC Braking
7 = Reserved
8 = Fire Mode
P007 Output Voltage 0 to 480 V ro 11-3
P009 Motor Torque -200.0 to 200.0 % ro, VVW 11-4
P011 Power Factor 0.00 to 1.00 ro 8-24
P012 DI8 to DI1 Status 0 to FF (hexa) ro 9-12
Bit 0 = DI1
Bit 1 = DI2
Bit 2 = DI3
Bit 3 = DI4
Bit 4 = DI5
Bit 5 = DI6
Bit 6 = DI7
Bit 7 = DI8
P013 DO4 to DO1 Status 0 to F (hexa) ro 9-22
Bit 0 = DO1
Bit 1 = DO2
Bit 2 = DO3
Bit 3 = DO4
P014 (*) AO1 Value 0.0 to 100.0 % ro 9-7
P015 (*) AO2 Value 0.0 to 100.0 % ro 9-7
P018 AI1 Value -100.0 to 100.0 % ro 9-1
P019 (*) AI2 Value -100.0 to 100.0 % ro 9-1
P020 (*) Potentiometer Signal Value -100.0 to 100.0 % ro 9-6
P022 FI Value in Hz 0 to 3000 Hz ro 9-10
P023 Main SW Version 0.00 to 99.99 ro 6-1
P024 (*) IO Acces. SW Version 0.00 to 99.99 ro 6-3
P025 (*) Comm. Acces. SW Version 0.00 to 99.99 ro 6-3
P027 Config. Acces. IO 0 = Without Accessory ro 6-3
1 = CFW300-IOAR
2 = CFW300-IODR
3 = CFW300-IOADR
4 = CFW300-IOAENC
5 = Reserved
6 = CFW300-IODF
P028 Config. Comm. Acces. 0 = Without Accessory ro 6-3
1 = CFW300-HMIR
2 = CFW300-CBLT
3 = CFW300-CCAN
4 = CFW300-CPDP
5 = CFW300-CETH
6 = Reserved
7 = CFW300-IOP
CFW300 | 0-1
0 Param. Description Adjustable Range Factory Setting Prop. Page

P029 Power HW Configuration 0 = Not identified 0 ro 6-1
1 = 1.6 A/110 V
2 = 2.6 A/110 V
3 = 4.2 A/110 V
4 = 6.0 A/110 V
5 = 1.6 A/220 V
6 = 2.6 A/220 V
7 = 4.2 A/220 V
8 = 6.0 A/220 V
9 = 7.3 A/220 V
10 = 10.0 A/220 V
11 = 15.2 A/220 V
12 to 19 = Reserved
20 = 1.1 A/380 V
21 = 1.8 A/380 V
22 = 2.6 A/380 V
23 = 3.5 A/380 V
24 = 4.8 A/380 V
25 = 6.5 A/380 V
26 = 8.2 A/380 V
27 = 10.0 A/380 V
28 = 12.0 A/380 V
29 = 15.0 A/380 V
P030 Module Temperature -200.0 to 200.0 ºC ro 11-4
P037 Motor Overload Ixt 0.0 to 100.0 % ro 10-4
P038 (*) Encoder Speed -9999 to 9999 rpm ro 9-20
P039 (*) Encoder Pulses Count 0 to 9999 ro 9-21
P045 Fan Enabled Time 0 to FFFF (hexa) ro 11-4
P047 CONF Status 0 to 33 (Table 11.3 on page 11-5) ro 11-4
P048 Present Alarm 0 to 999 ro 10-1
P049 Present Fault 0 to 999 ro 10-1
P050 Last Fault 0 to 999 ro 10-1
P051 Current At Last Fault 0.0 to 40.0 A ro 10-1
P052 DC Link At Last Fault 0 to 828 V ro 10-1
P053 Frequency At Last Fault 0.0 to 400.0 Hz ro 10-2
P054 Temperature Last Fault 0.0 to 200.0 ºC ro 10-2
P060 Second Fault 0 to 999 ro 10-1
P070 Third Fault 0 to 999 ro 10-1
P080 Last Fault on Fire Mode 0 to 999 ro 10-2
P081 Second Fault on Fire Mode 0 to 999 ro 10-2
P082 Third Fault on Fire Mode 0 to 999 ro 10-2
P100 Acceleration Time 0.1 to 999.9 s 5.0 s 8-2
P101 Deceleration Time 0.1 to 999.9 s 10.0 s 8-2
P102 Acceleration Time 2nd Ramp 0.1 to 999.9 s 5.0 s 8-2
P103 Deceleration Time 2nd Ramp 0.1 to 999.9 s 10.0 s 8-2
P104 Ramp S 0 = Inactive 0 cfg 8-2
1 = Active
P105 1st / 2nd Ramp Selection 0 = 1st Ramp 0 8-3
1 = 2nd Ramp
2 = DIx
3 = Serial/USB
4 = Reserved
5 = CO/DN/DP/ETH
6 = SoftPLC
P106 Emer. R. Acceleration Time 0.1 to 999.9 s 5.0 s 8-2
P107 Emer. R. Time Deceleration 0.1 to 999.9 s 5.0 s 8-2
P120 Speed Ref. Backup 0 = Inactive 1 7-7
1 = Active
2 = Backup by P121
P121 Reference via HMI 0.0 to 400.0 Hz 3.0 Hz 7-7
P122 JOG Reference -400.0 to 400.0 Hz 5.0 Hz 7-8
P124 Multispeed Ref. 1 -400.0 to 400.0 Hz 3.0 Hz 7-8
P125 Multispeed Ref. 2 -400.0 to 400.0 Hz 10.0 (5.0) Hz 7-8
0-2 | CFW300
Param. Description Adjustable Range Factory Setting Prop. Page 0

P133 Minimum Frequency 0.0 to 400.0 Hz 3.0 Hz 7-9
P134 Maximum Frequency 0.0 to 400.0 Hz 66.0 (55.0) Hz 7-9
P135 Maximum Output Current 0.0 to 40.0 A 1.5 x Inom V/f 8-7
P136 Manual Torque Boost 0.0 to 30.0 % According to the V/f 8-21
Inverter Model
P137 Automatic Torque Boost 0.0 to 30.0 % 0.0 % V/f 8-22
P138 Slip Compensation -10.0 to 10.0 % 0.0 % V/f 8-22
P139 Output Current Filter 0.000 to 9.999 s 0.050 s V/f, VVW 8-8
P140 Slip Com. Filter 0.000 to 9.999 s 0.500 s VVW 8-31
P142 Maximum Output Voltage 0.0 to 100.0 % 100.0 % cfg, V/f 8-23
P143 Intermediate Output Voltage 0.0 to 100.0 % 50.0 % cfg, V/f 8-23
P145 Field Weakening Speed 0.0 to 400.0 Hz 60.0 (50.0) Hz cfg, V/f 8-23
P146 Intermediate Frequency 0.0 to 400.0 Hz 30.0 (25.0) Hz cfg, V/f 8-23
P149 DC Link Comp. Mode 0 = Inactive 0 cfg, V/f 8-4
1 = Standard
2 = Overmodulation
3 = Extended
P150 DC/LC Regul. Type 0 = hold_Ud and decel_LC 0 cfg, V/f, 8-3
1 = accel_Ud and decel_LC VVW
2 = hold_Ud and hold_LC
3 = accel_Ud and hold_LC
P151 DC Link Regul. Level 325 to 810 V 430 V (P296 = 1) V/f, VVW 8-5
380 V (P296 = 2)
781 V (P296 = 4)
781 V (P296 = 5)
781 V (P296 = 6)
781 V (P296 = 7)
P153 Dynamic Braking Level 348 to 800 V According to the V/f, VVW 8-12
Inverter Model
P156 Rated Speed Overload Current 0.1 to 40.0 A 1.2 x Inom 10-5
P157 Overl.Curr.50 % Speed 0.1 to 40.0 A 1.2 x Inom 10-5
P158 Overl.Curr.20 % Speed 0.1 to 40.0 A 1.2 x Inom 10-5
P178 Rated Flux 50.0 to 150.0 % 100.0 % VVW 8-32
P191 (*) Clear Enc. Pulse Counter 0 = No 0 cfg 9-21
1 = Yes
P200 Password 0 = Inactive 0 cfg 5-1
1 = Active
2 to 9999 = New Password
P202 Type of Control 0 = V/f 0 cfg 8-1
1 = Quadratic V/f
2 to 4 = Not Used
5 = VVW
P204 Load/Save Parameters 0 to 4 = Not Used 0 cfg 5-2
5 = Load 60 Hz
6 = Load 50 Hz
7 = Load User
8 = Not Used
9 = Save User
10 = Not Used
11 = Load Default SoftPLC
12 to 13 = Reserved
P205 Main Display Parameter 0 to 999 2 5-3
P207 Bar Graph Parameter 0 to 999 3 5-3
P208 Ref. Scale Factor 1 to 9999 600 5-3
P209 Ref. Eng. Unit 0 to 1 = Without unit 3 5-3
2 = Volt (V)
3 = Hertz (Hz)
4 = Without unit
5 = Percent (%)
6 = Without unit
7 = Rotation/min. (rpm)
P210 Ref. Decimal Point 0 = wxyz 1 5-4
1 = wxy.z
2 = wx.yz
3 = w.xyz
P213 Bar Scale Factor 1 to 9999 1.0 x Inom 5-4
CFW300 | 0-3

P219 Red. Switch. Freq. 0.0 to 15.0 Hz 15.0 Hz cfg 8-8
P220 LOC/REM Selection Source 0 = Always Local 0 cfg 7-4
1 = Always Remote
2 to 3 = Not Used
4 = DIx
5 = Serial/USB (LOC)
6 = Serial/USB (REM)
7 to 8 = Not Used
9 = CO/DN/DP/ETH (LOC)
10 = CO/DN/DP/ETH (REM)
11 = SoftPLC
P221 LOC Reference Sel. 0 = HMI 0 cfg 7-4
1 = AI1
2 = AI2
3 = Potentiometer
4 = FI
5 = AI1 + AI2 > 0
6 = AI1 + AI2
7 = E.P.
8 = Multispeed
9 = Serial/USB
10 = Not Used
11 = CO/DN/DP/ETH
12 = SoftPLC
13 = Not Used
14 = AI1 > 0
15 = AI2 > 0
16 = Potentiometer > 0
17 = FI > 0
P222 REM Reference Selection See options in P221 1 cfg 7-4
P223 LOC FWD/REV Selection 0 = Forward 0 cfg 7-5
1 = Reverse
2 to 3 = Not Used
4 = DIx
5 = Serial/USB (FWD)
6 = Serial/USB (REV)
7 to 8 = Not Used
9 = CO/DN/DP/ETH (FWD)
10 = CO/DN/DP/ETH (REV)
11 = Not Used
12 = SoftPLC
P224 LOC Run/Stop Sel. 0 = HMI Keys 0 cfg 7-5
1 = DIx
2 = Serial/USB
3 = Not Used
4 = CO/DN/DP/ETH
5 = SoftPLC
P225 LOC JOG Selection 0 = Disabled 1 cfg 7-5
1 = Not Used
2 = DIx
3 = Serial/USB
4 = Not Used
5 = CO/DN/DP/ETH
6 = SoftPLC
P226 REM FWD/REV Selection See options in P223 4 cfg 7-5
P227 REM Run/Stop Selection See options in P224 1 cfg 7-5
P228 REM JOG Selection See options in P225 2 cfg 7-6
P229 Stop Mode Selection 0 = Ramp to Stop 0 cfg 7-6
1 = Coast to Stop
P230 Dead Zone (AIs and FI1 ) 0 = Inactive 0 cfg 9-1
1 = Active
0-4 | CFW300

P231 AI1 Signal Function 0 = Speed Ref. 0 cfg 9-2
1 to 3 = Not Used
4 = PTC
5 to 6 = Not Used
7 = PLC Use
8 = Application Function 1
16 = Control Setpoint
17 = Process Variable
P232 AI1 Input Gain 0.000 to 9.999 1.000 9-3
P233 AI1 Input Signal 0 = 0 to 10 V / 20 mA 0 9-3
1 = 4 to 20 mA
2 = 10 V / 20 mA to 0
3 = 20 to 4 mA
P234 AI1 Input Offset -100.0 to 100.0 % 0.0 % 9-4
P235 AI1 Input Filter 0.00 to 16.00 s 0.00 s 9-4
P236 (*) AI2 Signal Function See options in P231 0 cfg 9-2
P237 (*) AI2 Input Gain 0.000 to 9.999 1.000 9-3
P238 (*) AI2 Input Signal See options in P233 0 9-3
P239 (*) AI2 Input Offset -100.0 to 100.0 % 0.0 % 9-4
P240 (*) AI2 Input Filter 0.00 to 16.00 s 0.00 s 9-5
P241 (*) Potentiometer Signal Function 0 = Speed Ref. 0 cfg 9-6
1 to 6 = Not Used
7 = SoftPLC
16 to 17 = Not Used
P242 (*) Potentiometer Signal Gain 0.000 to 9.999 1.000 9-6
P244 (*) Potentiometer Signal Offset -100.0 to 100.0 % 0.0 % 9-6
P245 Potentiometer and FI1 Filter 0.00 to 16.00 s 0.00 s 9-6
P246 FI1 Input Function 0 = Inactive 0 cfg 9-11
1 = Active in DI1
2 = Active in DI2
3 = Active in DI3
4 = Active in DI4
P247 FI1 Input Gain 0.000 to 9.999 1.000 9-11
P248 FI1 Minimum Input 1 to 3000 Hz 100 Hz 9-11
P249 FI1 Input Offset -100.0 to 100.0 % 0.0 % 9-11
P250 FI1 Maximum Input 1 to 3000 Hz 1000 Hz 9-11
CFW300 | 0-5

P251 (*) AO1 Output Function 0 = Speed Ref. 2 9-7
1 = Not Used
2 = Real Speed
3 to 4 = Not Used
5 = Output Current
6 = Not Used
7 = Active Current
8 to 10 = Not Used
11 = Motor Torque
12 = SoftPLC
13 to 15 = Not Used
16 = Motor Ixt
17 = Not Used
18 = P696 Value
19 = P697 Value
20 = Not Used
P252 (*) AO1 Output Gain 0.000 to 9.999 1.000 9-8
P253 (*) AO1 Output Signal 0 = 0 to 10 V 0 9-9
1 = 0 to 20 mA
2 = 4 to 20 mA
3 = 10 to 0 V
4 = 20 to 0 mA
5 = 20 to 4 mA
P254 (*) AO2 Output Function See options in P251 5 9-8
P255 (*) AO2 Output Gain 0.000 to 9.999 1.000 9-8
P256 (*) AO2 Output Signal See options in P253 0 9-9
0-6 | CFW300

P263 DI1 Input Function 0 = Not Used 1 cfg 9-12
1 = Run/Stop
2 = General Enable
3 = Quick Stop
4 = Forward Run
5 = Reverse Run
6 = Start
7 = Stop
8 = Direction of Rotation
9 = LOC/REM
10 = JOG
11 = Accelerate E.P.
12 = Decelerate E.P.
13 = Multispeed
14 = 2nd Ramp
15 to 17 = Not Used
18 = No Ext. Alarm
19 = No Ext. Fault
20 = Reset
21 to 23 = Not Used
24 = Disab. Flying Start
25 = Not Used
26 = Lock Prog.
27 to 31 = Not Used
32 = 2nd Ramp Multispeed
33 = 2nd Ramp Increase E.P.
34 = 2nd Ramp Decrease E.P.
35 = 2nd Ramp FWD Run
36 = 2nd Ramp REV Run
37 = Start / Inc. E.P.
38 = Dec. E.P. / Stop
39 = Stop
40 = Safety Switch
49 = Enable Fire Mode
50 to 54 = Not Used
55 = Run/Stop with Line Start
Lockout
56 = Forward Run with Line Start
Lockout
57 = Reverse Run with Line Start
Lockout
CFW300 | 0-7

1 = Run/Stop
2 = General Enable
3 = Quick Stop
4 = Forward Run
5 = Reverse Run
6 = Start
7 = Stop
9 = LOC/REM
10 = JOG
13 = Multispeed
14 = 2nd Ramp
15 to 17 = Not Used
18 = No Ext. Alarm
19 = No Ext. Fault
20 = Reset
21 to 23 = Not Used
24 = Disab.FlyStart
25 = Not Used
26 = Progr. Off
27 to 31 = Not Used
37 = Turn ON / Ac. E.P.
38 = De. E.P. / Turn OFF
39 = Stop
40 = Safety Switch
50 = PID Manual / Automatic
51 to 54 = Not Used
Lockout
Lockout
Lockout
0-8 | CFW300

1 = Run/Stop
2 = General Enable
3 = Quick Stop
4 = Forward Run
5 = Reverse Run
6 = Start
7 = Stop
9 = LOC/REM
10 = JOG
13 = Multispeed
14 = 2nd Ramp
15 to 17 = Not Used
18 = No Ext. Alarm
19 = No Ext. Fault
20 = Reset
21 to 23 = Not Used
24 = Disab.FlyStart
25 = Not Used
26 = Lock Prog.
27 to 31 = Not Used
39 = Stop
40 = Safety Switch
50 = Not Used
51 = Command to Increase the
Control Setpoint (EP)
52 = Not Used
53 = 1st DI for Control Setpoint
Selection
54 = Not Used
Lockout
Lockout
Lockout
CFW300 | 0-9

1 = Run/Stop
2 = General Enable
3 = Quick Stop
4 = Forward Run
5 = Reverse Run
6 = Start
7 = Stop
9 = LOC/REM
10 = JOG
13 = Multispeed
14 = 2nd Ramp
15 to 17 = Not Used
18 = No Ext. Alarm
19 = No Ext. Fault
20 = Reset
21 to 23 = Not Used
24 = Disab.FlyStart
25 = Not Used
26 = Progr. Off
27 to 31 = Not Used
39 = Stop
40 = Safety Switch
50 to 51 = Not Used
52 = Command to Decrease the
Control Setpoint (EP)
53 = Not Used
54 = 2nd DI for Control Setpoint
Selection
Lockout
Lockout
Lockout
P267 (*) DI5 Input Function See options in P263 0 cfg 9-12
P271 DIs Function 0 = (DI1..DI8) NPN 0 cfg 9-15
1 = (DI1..DI4) PNP
2 = (DI5..DI8) PNP
3 = (DI1..DI8) PNP
0-10 | CFW300

P275 DO1 Function 0 = Not Used 13 9-22
1 = F* ≥ Fx
2 = F ≥ Fx
3 = F ≤ Fx
4 = F = F*
5 = Not Used
6 = Is > Ix
7 = Is < Ix
8 = Torque > Tx
9 = Torque < Tx
10 = Remote
11 = Run
12 = Ready
13 = No Fault
14 = No F070
15 = Not Used
16 = No F021/F022
17 = Not Used
18 = No F072
19 = 4-20 mA OK
20 = P695 Value
21 = Forward
22 to 23 = Not Used
24 = Ride-Through
25 = Pre-Charge OK
26 = Fault
27 = Not Used
28 = SoftPLC
29 to 34 = Not Used
35 = No Alarm
36 = Without fault and alarm
45 = Fire Mode ON
46 = Low Level of Process Variable
47 = High Level of Process Variable
P276 (*) DO2 Function See options in P275 0 9-22
P281 Fx Frequency 0.0 to 400.0 Hz 3.0 Hz 9-24
P282 Fx Hysteresis 0.0 to 15.0 Hz 0.5 Hz 9-25
P290 Ix Current 0.0 to 40.0 A 1.0 x Inom 9-25
P293 Tx Torque 0 to 200 % 100 % 9-25
P295 Inverter Rated Current 1.1 to 15.2 A According to the ro 6-2
Inverter Model
P296 Line Rated Voltage 0 = Reserved According to the cfg 6-3
1 = 110 - 127 Vac Inverter Model
2 = 200 - 240 Vac | 310 Vdc
3 = Reserved
4 = 380 Vac | 513 Vdc
5 = 415 Vac | 560 Vdc
6 = 440 Vac | 594 Vdc
7 = 480 Vac | 650 Vdc
P297 Switching Frequency 2.5 to 15.0 kHz 5.0 kHz cfg, V/f, 8-9
VVW
P299 DC Braking Start Time 0.0 to 15.0 s 0.0 s V/f, VVW 8-10
P300 DC Braking Stop Time 0.0 to 15.0 s 0.0 s V/f, VVW 8-11
P301 DC Braking Frequency 0.0 to 15.0 Hz 3.0 Hz V/f, VVW 8-11
P302 DC Braking Current 0.0 to 100.0 % 20.0 % V/f, VVW 8-12
P303 Skip Frequency 1 0.0 to 400.0 Hz 0.0 Hz V/f, VVW 8-13
P304 Skip Frequency 2 0.0 to 400.0 Hz 0.0 Hz V/f, VVW 8-13
P306 Skip Band 0.0 to 25.0 Hz 0.0 Hz V/f, VVW 8-14
P308 Serial Address 1 to 247 1 cfg 12-2
CFW300 | 0-11

P310 Serial Baud Rate 0 = 9600 bits/s 1 cfg 12-3
1 = 19200 bits/s
2 = 38400 bits/s
3 = 57600 bits/s
4 = 76800 bits/s
P311 Serial Bytes Config. 0 = 8 bits, no, 1 1 cfg 12-3
1 = 8 bits, even,1
2 = 8 bits, odd, 1
3 = 8 bits, no, 2
4 = 8 bits, even,2
5 = 8 bits, odd, 2
P312 Serial Protocol 0 to 1 = Reserved 2 cfg 12-3
2 = Modbus RTU Slave
3 = BACnet
4 = Reserved
5 = ModBus RTU Master
P313 Action for Communic. Error 0 = Inactive 1 12-1
1 = Ramp Stop
2 = General Disable
3 = Go to LOC
4 = LOC Keep Enab.
5 = Cause Fault
P314 Serial Watchdog 0.0 to 999.0 s 0.0 s cfg 12-3
P316 Serial Interf. Status 0 = Inactive ro 12-3
1 = Active
2 = Watchdog Error
P320 Flying Start / Ride-Through 0 = Inactive 0 cfg 8-9
1 = Flying Start
2 = FS / RT
3 = Ride-Through
P331 Voltage Ramp for FS and RT 0.2 to 60.0 s 2.0 s 8-10
P332 Dead Time 0.1 to 10.0 s 1.0 s 8-10
P340 Auto-Reset Time 0 to 255 s 0s 10-2
P352 Fan Control Config. 0 = OFF 2 cfg 10-3
1 = ON
2 = CT
P358 (*) Encoder Fault Config. 0 = Inactive 3 cfg 9-21
1 = F067 ON
2 = F079 ON
3 = F067 and F079 ON
P375 (*) External Sensor Temp. 0 to 200 ºC ro 9-5
P397 Control Config 0 to F (hexa) 11 cfg 8-16
Bit 0 = Slip Compens. Regen.
Bit 1 = Dead Time Comp.
Bit 2 = Is Stabilization
Bit 3 = P297 reduction in A050
P399 Motor Rated Efficiency 50.0 to 99.9 % According to the cfg, VVW 8-32
Inverter Model
P400 Motor Rated Voltage 0 to 480 V 220 V cfg, VVW 8-32
P401 Motor Rated Current 0.0 to 40.0 A 1.0 x Inom cfg, VVW 8-32
P402 Motor Rated Speed 0 to 24000 rpm 1720 rpm cfg, VVW 8-33
P403 Motor Rated Frequency 0 to 400 Hz 60 Hz cfg, VVW 8-33
P404 Motor Rated Power 0 = 0.16 HP (0.12 kW) 2 cfg, VVW 8-33
1 = 0.25 HP (0.18 kW)
2 = 0.33 HP (0.25 kW)
3 = 0.50 HP (0.37 kW)
4 = 0.75 HP (0.55 kW)
5 = 1.00 HP (0.75 kW)
6 = 1.50 HP (1.10 kW)
7 = 2.00 HP (1.50 kW)
8 = 3.00 HP (2.20 kW)
9 = 4.00 HP (3.00 kW)
10 = 5.00 HP (3.70 kW)
11 = 5.50 HP (4.00 kW)
12 = 6.00 HP (4.50 kW)
13 = 7.50 HP (5.50 kW)
14 = 10.00 HP (7.50 kW)
P405 (*) Encoder Pulses Number 32 to 9999 1024 cfg, VVW 9-21
P407 Motor Rated Power Factor 0.50 to 0.99 According to the cfg, VVW 8-24
Inverter Model
0-12 | CFW300

P408 Run Self-Tuning 0 = No 0 cfg, VVW 8-33
1 = Yes
P409 Stator Resistance 0.01 to 99.99 According to the cfg, VVW 8-34
Inverter Model
P510 SoftPLC Eng. Unit See options in P209 0 5-3
P511 SoftPLC Indication Form See options in P210 1 5-4
P580 Fire Mode Configuration 0 = Inactive 0 cfg 8-16
1 = Active
2 = Active / P134
3 = Reserved
4 = Active / General Disable
P582 Fire Mode Auto-reset Adjustable 0 = Limited 0 cfg 8-16
1 = Unlimited
P588 EOC Maximum Torque 0 to 85 % 0% cfg 8-25
P589 EOC Minimum Voltage 40 to 80 % 40 % cfg 8-25
P590 EOC Minimum Frequency 12.0 to 400.0 Hz 20.0 Hz cfg 8-25
P591 EOC Hysteresis 0 to 30 % 10 % cfg 8-25
P613 Main SW Revision -9999 to 9999 ro 6-3
P680 Logical Status 0 to FFFF (hexa) ro 11-6
Bit 0 = Reserved
Bit 1 = Run Command
Bit 2 = Fire Mode
Bit 3 to 4 = Reserved
Bit 5 = 2nd Ramp
Bit 6 = Config. Mode
Bit 7 = Alarm
Bit 8 = Running
Bit 9 = Enabled
Bit 10 = Forward
Bit 11 = JOG
Bit 12 = Remote
Bit 13 = Subvoltage
Bit 14 = Reserved
Bit 15 = Fault
P681 13-Bit Speed 0 to FFFF (hexa) ro 11-7
P682 Serial/USB Control 0 to FFFF (hexa) ro 12-1
Bit 0 = Ramp Enable
Bit 1 = General Enable
Bit 2 = Run Forward
Bit 3 = JOG Enable
Bit 4 = Remote
Bit 5 = 2nd Ramp
Bit 6 = Reserved
Bit 7 = Fault Reset
P683 Serial/USB Speed Ref. 0 to FFFF (hexa) ro 12-2
P684 (*) CO/DN/DP/ETH Control 0 to FFFF (hexa) ro 12-1
Bit 0 = Ramp Enable
Bit 2 = Run Forward
Bit 3 = JOG Enable
Bit 4 = Remote
Bit 5 = 2nd Ramp
Bit 6 = Reserved
Bit 7 = Fault Reset
P685 (*) CO/DN/DP/ETH Speed Ref 0 to FFFF (hexa) ro 12-2
P690 Logic State 2 0 to FFFF (hexa) ro 11-7
Bit 2 = DC Link Voltage Extended
Bit 3 = Energy Saver
Bit 4 = Fs Reduction
Bit 5 = Reserved
Bit 6 = Deceleration Ramp
Bit 7 = Acceleration Ramp
Bit 8 = Freeze Ramp
Bit 9 = Setpoint Ok
Bit 10 = DC Link Regulation
Bit 11 = 50 Hz Config
Bit 12 = Ride-Through
Bit 13 = Flying Start
Bit 14 = DC Braking
Bit 15 = PWM pulse
CFW300 | 0-13

P695 DOx Value 0 to 7F (hexa) ro 9-25
Bit 0 = DO1
Bit 1 = DO2
Bit 2 = DO3
Bit 3 = DO4
P696 (*) AOx Value 1 0 to FFFF (hexa) ro 9-9
P697 (*) AOx Value 2 0 to FFFF (hexa) ro 9-9
P700 (*) CAN Protocol 1 = CANopen 12-5
2 = DeviceNet
P701 (*) CAN Address 0 to 127 63 12-5
P702 (*) CAN Baud Rate 0 = 1 Mbps/Auto 0 12-5
1 = Reserved/Auto
2 = 500 Kbps
3 = 250 Kbps
4 = 125 Kbps
5 = 100 Kbps/Auto
6 = 50 Kbps/Auto
7 = 20 Kbps/Auto
8 = 10 Kbps/Auto
P703 (*) Bus Off Reset 0 = Manual 1 12-5
1 = Automatic
P705 (*) CAN Controller Status 0 = Disabled ro 12-5
1 = Auto-baud
2 = CAN Active
3 = Warning
4 = Error Passive
5 = Bus Off
6 = No Bus Power
P706 (*) RX CAN Telegrams 0 to 9999 ro 12-6
P707 (*) TX CAN Telegrams 0 to 9999 ro 12-6
P708 (*) Bus Off Counter 0 to 9999 ro 12-6
P709 (*) CAN Lost Messages 0 to 9999 ro 12-6
P710 (*) DeviceNet I/O instances 0 = ODVA Basic 2W 0 12-6
1 = ODVA Extend 2W
2 = Manuf.Spec.2W
3 = Manuf.Spec.3W
4 = Manuf.Spec.4W
5 = Manuf.Spec.5W
6 = Manuf.Spec.6W
P711 (*) DeviceNet Read Word #3 0 to 1199 0 12-6
P715 (*) DeviceNet Write Word #3 0 to 1199 0 12-6
P719 (*) DeviceNet Network Status 0 = Offline ro 12-7
1 = OnLine, Not Conn
2 = OnLine, Connect.
3 = Connection Timed out
4 = Link Failure
5 = Auto-Baud
P720 (*) DeviceNet Master Status 0 = Run ro 12-7
1 = Idle
P721 (*) CANopen Comm. Status 0 = Disabled ro 12-7
1 = Reserved
2 = Communic. Enabled
3 = Error Ctrl. Enable
4 = Guarding Error
5 = Heartbeat Error
P722 (*) CANopen Node Status 0 = Disabled ro 12-7
1 = Initialization
2 = Stopped
3 = Operational
4 = Preoperational
0-14 | CFW300

P740 (*) Profibus Comm. Status 0 = Disabled ro 12-8
1 = Access Error
2 = Offline
3 = Config. Error
4 = Param. Error
5 = Clear Mode
6 = Online
P742 (*) Profibus Read Word #3 0 to 1199 0 12-8
P746 (*) Profibus Write Word#3 0 to 1199 0 12-8
P750 (*) Profibus Address 1 to 126 1 12-8
P751 (*) Profibus Teleg. Sel. 1 = Std. Teleg. 1 1 12-8
2 = Telegram 100
3 = Telegram 101
4 = Telegram 102
5 = Telegram 103
P754 (*) Profibus Baud Rate 0 = 9.6 kbit/s 0 12-9
1 = 19.2 kbit/s
2 = 93.75 kbit/s
3 = 187.5 kbit/s
4 = 500 kbit/s
5 = Not Detected
6 = 1500 kbit/s
7 = 3000 kbit/s
8 = 6000 kbit/s
9 = 12000 kbit/s
10 = Reserved
11 = 45.45 kbit/s
P760 BACnet Dev Inst Hi 0 to 419 0 12-4
P761 BACnet Dev Inst Lo 0 to 9999 0 12-4
P762 Max Number of master 0 to 127 127 12-4
P763 MS/TP Max info Frame 0 to FFFF (hexa) 1 12-4
P764 I-AM Msg transmition 0 = Power Up 0 12-4
1 = Continuous
P765 Token RX Quantity 0 to FFFF (hexa) ro 12-5
P770 (*) Blueooth Device Name 0 to 9999 Serial Number of the 12-4
Inverter
P771 (*) Bluetooth Password PIN 0 to 9999 1234 12-4
P840 (*) IR Control Command 0 to FFFF (hexa) ro 9-20
P841 (*) IR Controle Selection 0 = Without Display 0 cfg 9-20
1 = With Display
P842 (*) Quick View 1 IR 0 to 959 2 5-4
P843 (*) Quick View 2 IR 0 to 959 375 5-4
P850 (*) IP Address Config 0 = Parameters 1 cfg 12-9
1 = DHCP
P851 (*) IP Address 1 0 to 255 192 cfg 12-9
CFW300 | 0-15

P855 (*) CIDR Sub-net 0 = Reserved 24 cfg 12-10
1 = 128.0.0.0
2 = 192.0.0.0
3 = 224.0.0.0
4 = 240.0.0.0
5 = 248.0.0.0
6 = 252.0.0.0
7 = 254.0.0.0
8 = 255.0.0.0
9 = 255.128.0.0
10 = 255.192.0.0
11 = 255.224.0.0
12 = 255.240.0.0
13 = 255.248.0.0
14 = 255.252.0.0
15 = 255.254.0.0
16 = 255.255.0.0
17 = 255.255.128.0
18 = 255.255.192.0
19 = 255.255.224.0
20 = 255.255.240.0
21 = 255.255.248.0
22 = 255.255.252.0
23 = 255.255.254.0
24 = 255.255.255.0
25 = 255.255.255.128
26 = 255.255.255.192
27 = 255.255.255.224
28 = 255.255.255.240
29 = 255.255.255.248
30 = 255.255.255.252
31 = 255.255.255.254
P856 (*) Gateway 1 0 to 255 0 cfg 12-10
P857 (*) Gateway 2 0 to 255 0 cfg 12-10
P858 (*) Gateway 3 0 to 255 0 cfg 12-10
P859 (*) Gateway 4 0 to 255 0 cfg 12-10
P860 (*) MBTCP: Communication Status 0 = Disabled ro 12-11
1 = No connection
2 = Connected
3 = Timeout Error
P863 (*) MBTCP: Active Connections 0 to 4 ro 12-11
P865 (*) MBTCP: TCP Port 0 to 9999 502 cfg 12-11
P868 (*) MBTCP: Timeout 0.0 to 999.9 s 0.0 s cfg 12-11
P869 (*) EIP: Master Status 0 = Run ro 12-11
1 = Idle
P870 (*) EIP: Communication Status 0 = Disabled ro 12-11
1 = No connection
2 = Connected
3 = Timeout in I/O Connection
4 = Reserved
P871 (*) EIP: Data Profile 0 to 3 = Reserved 8 cfg 12-11
4 = 120/170: CIP Basic Speed + I/O
5 = 121/171: CIP Extended Speed +
I/O
6 to 7 = Reserved
8 = 100/150: Manufac. Speed + I/O
9 to 10 = Reserved
P872 (*) Ethernet Read Word #3 0 to 9999 0 12-12
P880 (*) Ethernet Write Word #3 0 to 9999 0 12-12
0-16 | CFW300

P889 (*) Ethernet Interface Status 0 to 3 (hexa) ro 12-12
Bit 0 = Link 1
Bit 1 = Link 2
P900 SoftPLC Status 0 = No Application ro 13-1
1 = Installing Application
2 = Incompat. Application
3 = Application Stopped
4 = Application Running
P901 SoftPLC Command 0 = Stop Application 0 13-1
1 = Run Application
P902 Scan Cycle Time 0.000 to 9.999 s ro 13-1
P903 SoftPLC Appl. 0 = User 1 cfg 13-1
1 = PID Controller
P904 Action for SoftPLC Application not 0 = Disabled 0 13-2
Running 1 = Cause Alarm (A708)
2 = Cause Fault (F709)
P910 SoftPLC Parameter 1 -9999 to 9999 0 13-2
CFW300 | 0-17

SoftPLC Parameter Configuration for PID Controller Application (P903 = 1)

P910 PID Controller Application Version 0.00 to 90.00 ro 13-2
P911 Control Setpoint -99.99 to 99.99 2.00 13-2
P912 Control Setpoint 1 -99.99 to 99.99 2.00 13-2
P916 Control Process Variable -99.99 to 99.99 ro 13-2
P917 PID Controller Output 0.0 to 100.0% ro 13-2
P918 PID Controller Setpoint in Manual 0.0 to 400.0Hz 0.0Hz 13-2
Mode
P919 PID Controller Logical Status 0 to FFFF (hexa) ro 13-2
Bit 0 = Sleep Mode Active (A750)
Bit 1 = PID in Manual (0) / Automatic
(1)
Bit 2 = PV Low Level (A760)
Bit 3 = PV Low Level (F761)
Bit 4 = PV High Level (A762)
Bit 5 = PV High Level (F763)
P920 Selection of the Control Setpoint 0 = Control Setpoint via HMI or 0 cfg 13-2
Source Communication Networks (P911)
1 = Control Setpoint via Analog Input
AI1
2 = Control Setpoint via Analog Input
AI2
3 = Control Setpoint via Electronic
Potentiometer (EP)
4 = Two Setpoints via Digital Input DI3
(P912 and P913)
5 = Three Setpoints via Digital Inputs
DI3 and DI4 (P912, P913 and P914)
6 = Four Setpoints via Digital Inputs
DI3 and DI4 (P912, P913, P914 and
P915)
P921 Selection of the Control Process 1 = Control Process Variable via 1 cfg 13-2
Variable Source Analog Input AI1
2 = Control Process Variable via
Analog Input AI2
3 = Control Process Variable via
Difference between Analog Input AI1
and AI2
P922 Minimum Sensor Level of the -99.99 to 99.99 0.00 13-3
Control Process Variable
P923 Maximum Sensor Level of the -99.99 to 99.99 4.00 13-3
P924 Value for Low Level Alarm for the -99.99 to 99.99 1.00 13-3
P925 Time for Low Level Fault for the 0.0 to 999.9s 0.0s 13-3
P926 Value for High Level Alarm for the -99.99 to 99.99 3.50 13-3
P927 Time for High Level Fault for the 0.0 to 999.9s 0.0s 13-3
P928 Selection of the PID Controller 0 = Disable PID Controller 0 cfg 13-3
Control Action 1 = Enable PID Controller in Direct
Mode
2 = Enable PID Controller in Reverse
Mode
P929 PID Controller Operation Mode 0 = Manual 2 13-3
1 = Automatic
2 = Select Control to Manual (0) or
Automatic (1) via digital input DI2
0-18 | CFW300
SoftPLC Parameter Configuration for PID Controller Application (P903 = 1) 0

P930 Automatic Adjustment of the PID 0 = P911 inactive and P918 inactive 0 13-3
Controller Setpoint 1 = P911 active and P918 inactive
2 = P911 inactive and P918 active
3 = P911 active and P918 active
P931 Proportional Gain 0.00 to 99.99 1.00 13-3
P932 Integral Gain 0.00 to 99.99 5.00 13-3
P933 Derivative Gain 0.00 to 99.99 0.00 13-3
P934 PID Controller Sampling Period 0.050 to 9.999s 0.100s cfg 13-3
P935 Filter for the PID Controller Control 0.000 to 9.999s 0.150s 13-3
Setpoint
P936 Deviation of the Control Process -99.99 to 99.99 0.30 13-3
Variable to Wake Up
P937 Time to Wake Up 0.0 to 999.9s 5.0s 13-3
P938 Motor Speed to activate the Sleep 0.0 to 400.0Hz 0.0Hz 13-3
Mode
P939 Time to activate de Sleep Mode 0.0 to 999.9s 10.0s 13-3
Notes:
(*) Only available when IO or communication expansion accessory is present (connected). For further information,
refer to the respective accessory guide.
ro = Read only parameter
cfg = Configuration parameter, value can be programmed only with motor stopped
V/f = Available when V/f control mode is chosen
VVW = Available when VVW control mode is chosen
CFW300 | 0-19
0-20 | CFW300
QUICK REFERENCE OF ALARMS AND FAULTS
1 QUICK REFERENCE OF ALARMS AND FAULTS
Fault / Alarm Description Possible Causes

F021 Undervoltage fault on the intermediate Wrong voltage supply; check if the data on the inverter label 1
Undervoltage on the DC Link circuit. comply with the power supply and parameter P296.
Supply voltage too low, producing voltage on the DC Link
below the minimum value (Level F021) according to Table
10.1 on page 10-3.
Phase fault in the input.
Fault in the pre-charge circuit.
F022 Overvoltage fault on the intermediate Wrong voltage supply; check if the data on the inverter label
Overvoltage on the DC Link circuit. comply with the power supply and parameter P296.
Supply voltage is too high, producing voltage on the DC
Link above the maximum value (Level F022) according to
Table 10.1 on page 10-3.
Load inertia is too high or deceleration ramp is too fast.
P151 setting is too high.
F031 Main control cannot establish the Accessory damaged.
Fault in Communication with communication link with the IOs Poor connection of the accessory.
Expansion Accessory expansion accessory. Problem in the identification of the accessory; refer to P027.
F032 Main control cannot establish Accessory damaged.

Comm. Plug-in module the communication link with the Poor connection of the accessory.
comunication Lost communication acccessory. Problem in the identification of the accessory; refer to P028.
F033 Stator resistance setting fault P409. Stator resistance value in P409 does not comply with the
VVW Self-tuning Fault inverter power.
Motor connection error; turn off the power supply and
check the motor terminal box and the connections with the
motor terminals.
Motor power too low or too high in relation to the inverter.
A046 Motor overload alarm. Settings of P156 is too low for the used motor.
Motor Overload Overload on the motor shaft.
A050 Overtemperature alarm from the power High temperature at IGBTs. P030 > Level A050, according
IGBTs Overtemperatures module temperature sensor (NTC). to Table 11.2 on page 11-4.
High ambient temperature around the inverter and high
output current. For further information, refer to of the
user’s manual available for download on the website:
www.weg.net.
Blocked or defective fan.
Heatsink is too dirty, preventing the air flow.
F051 Overtemperature fault measured on High temperature at IGBTs. P030 > Level F051, according
IGBTs Overtemperatures the temperature sensor of the power to Table 11.2 on page 11-4.
pack. High ambient temperature around the inverter and high
output current. For further information, refer to of the
user’s manual available for download on the website:
www.weg.net.
Blocked or defective fan.
Heatsink is too dirty, preventing the air flow.
F067 Fault related to the phase relation of the Output motor cables U, V, W are inverted.
Incorrect Encoder/ Motor encoder signals. Encoder channels A and B are inverted.
Wiring Encoder was not properly mounted.
F070 Overcurrent or short-circuit on the Short-circuit between two motor phases.
Overcurrent/Shortcircuit output, DC Link or braking resistor. IGBTs module in short-circuit or damaged.
Start with too short acceleration ramp.
Start with motor spinning without the Flying Start function.
F072 Motor overload fault. P156, P157 or P158 setting is too low in relation to the
Motor Overload motor operating current.
Overload on the motor shaft.
F078 Overtemperature fault measured on Overload on the motor shaft.
Motor Overtemperature the motor temperature sensor (Triple Load cycle is too high (high number of starts and stops per
PTC) via analog input AIx minute).
High ambient temperature around the motor.
Poor contact or short-circuit (3k9 < RPTC < 0k1).
Motor thermistor not installed.
Motor shaft is stuck.
F079 Fault of encoder signals absent. Wiring between encoder and interface accessory to
Encoder Signal Fault encoder broken.
Encoder defective.
F080 Fault related to the supervision Electric noise.
CPU Fault (Watchdog) algorithm of the inverter main CPU. Inverter firmware fault.
CFW300 | 1-1

F081 Fault of end of memory to save user’s Attempt to save (P204 = 9) more than 32 parameters
End of User’s Memory parameter table. (with values different from the factory default) on the User
parameter table.
1 F082 Fault in data transfer using MMF Attempt to download data from the flash memory module
Fault in Data Transfer (MMF) accessory. to the inverter with the inverter energized.
Attempt to download a SoftPLC application incompatible
with the destination inverter.
Problems saving data downloaded to the inverter.
F084 Fault related to the automatic Poor contact in the connection between the main control
Auto-diagnosis Fault identification algorithm of the inverter and the power pack.
hardware. Hardware not compatible with the firmware version.
Defect on the internal circuits of the inverter.
A090 External alarm via DIx (option “no Wiring on DI1 to DI8 inputs are open or have poor contact.
External Alarm external alarm” in P263 to P270).
F091 External fault via DIx (“no external fault” Wiring on DI1 to DI8 inputs are open or have poor contact.
External Fault in P263 to P270).
A128 It indicates that the device stopped Check network installation, broken cable or fault/poor
Telegram Reception Timeout receiving valid telegrams for a period contact on the connections with the network, grounding.
longer than the setting in P314. Ensure the master always sends telegrams to the
The time counting starts as soon as it equipment in a time shorter than the setting in P314.
receives the first valid telegram, with Disable this function in P314.
correct address and error-checking
field.
A133 It indicates that the CAN interface has Measure if there is voltage within the allowed range between
No Power Supply on the CAN no power supply between pins 25 and pins 25 and 29 of the CAN interface connector.
Interface 29 of the connector. Check if the power supply cables are not misconnected or
inverted.
Check for contact problems on the cable or connector of
the CAN interface.
A134 Bus off error detected on the CAN Check for short circuit on the CAN circuit transmission
Bus Off interface. cable.
Check if the cables are not misconnected or inverted.
Check if all the network devices use the same baud rate.
Check if the termination resistors with the right specification
were installed only at the end of the main bus.
Check if the CAN network was properly installed.
A135 CANopen communication error control Check the times set on the master and on the slave for
Node Guarding/ Heartbeat detected communication error using message exchange. In order to prevent problems due to
the guarding mechanism. transmission delays and time counting, it is recommended
that the values set for error detection by the slave be
multiples of the times set for message exchange on the
master.
Check if the master is sending the guarding telegrams in
the time set.
Check problems in the communication that may cause
missing telegrams or transmission delays.
A136 Alarm indicates that the DeviceNet Set the switch that controls the master operation of the
Idle Master network master is in Idle mode. master for Run or the corresponding bit on the configuration
word of the master software. If further information is
needed, refer to the documentation of the master used.
A137 Alarm that indicates that one or more Check the network master status.
DeviceNet Connection Timeout DeviceNet connections timed out. Check network installation, broken cable or fault/poor
contact on the connections with the network.
A138 It indicates that the inverter received Check the network master status, ensuring it is in the run
Profibus DP Interface in Clear the command from the Profibus DP mode.
Mode network master to go into clear mode.
A139 It indicates interruption in the Check if the network master is correctly configured and
Offline Profibus DP Interface communication between the Profibus operating properly.
DP network master and the inverter. Check for short-circuit or poor contact on the
The Profibus DP communication communication cables.
interface went into offline status. Check if the cables are not misconnected or inverted.
Check if the termination resistors with the right value were
installed only at the end of the main bus.
Check the network installation in general - cabling,
grounding.
A140 It indicates error in the access to the Check if the Profibus DP module is correctly fitted.
Profibus DP Module Access Profibus DP communication module Hardware errors due to improper handling or installation
Error data. of the accessory, for instance, may cause this error. If
possible, carry out tests by replacing the communication
accessory.
1-2 | CFW300

A147 It indicates interruption in the cyclic Check the status of the network master.
EtherNet/IP Communication communication with EtherNet/IP Check the network installation, broken cable or failed/bad
Offline master. contact in the network connections.
It occurs when, for any reason, after
the cyclic communication of the master
1
with the product is started, this
communication is interrupted.
A149 It indicates that the device stopped Check network installation, broken cable or fault/poor
Timeout Modbus TCP receiving valid telegrams for a period contact on the connections with the network, grounding.
longer than the setting in P868. Ensure the Modbus TCP client always sends telegrams to
The time counting starts as soon as it the equipment in a time shorter than the setting in P868.
receives the first valid telegram. Disable this function in P868.
A163 Analog input signal AI1 at 4 to 20 mA Current signal on the analog input AI1 interrupted or null.
Signal Fault AI1 4...20 mA or 20 to 4 mA is below 2 mA. Parameterization error on analog input AI1.
A164 .Analog input signal AI2 at 4 to 20 mA Current signal on the analog input AI2 interrupted or null.
Signal Fault AI2 4...20 mA or 20 to 4 mA is below 2 mA. Parameterization error on analog input AI2.
A177 Alarm to replace the fan (P045 > 50000 Maximum number of operation hours of the heatsink fan
Replace Fan hours). exceeded.
F182 Pulse feedback circuit fault of the Hardware identification fault; compare P295 and P296 to
Pulse Feedback Failure output voltage. the inverter identification label.
Note: it may be turned off in P397. Inverter internal pulse feedback circuit fault.
A211 Indicates that the drive is in Fire Mode. The digital input programmed for activating the Fire Mode
Drive in Fire Mode is active.
F228 It indicates that the device stopped Check network installation, broken cable or fault/poor
Timeout in Receipt of receiving valid telegrams for a period contact on the connections with the network, grounding.
Telegrams longer than the setting in P314. Ensure the master always sends telegrams to the
The time counting starts as soon as it equipment in a time shorter than the setting in P314.
receives the first valid telegram, with Disable this function in P314.
correct address and error-checking
field.
F233 It indicates that the CAN interface has Measure if there is voltage within the allowed range between
No Power Supply on the CAN no power supply between pins V(-) and pins V(-) and V(+) of the CAN interface connector.
Interface V(+) of the connector. Check if the power supply cables are not misconnected or
inverted.
Check for contact problems on the cable or connector of
the CAN interface.
F234 Bus off error detected on the CAN Check for short circuit on the CAN circuit transmission
Bus Off interface. cable.
Check if the cables are not misconnected or inverted.
Check if all the network devices use the same baud rate.
Check if the termination resistors with the right specification
were installed only at the end of the main bus.
Check if the CAN network was properly installed.
F235 CANopen communication error control Check the times set on the master and on the slave for
Node Guarding/ Heartbeat detected communication error using message exchange. In order to prevent problems due to
the guarding mechanism. transmission delays and time counting, it is recommended
that the values set for error detection by the slave be
multiples of the times set for message exchange on the
master.
Check if the master is sending the guarding telegrams in
the time set.
Check problems in the communication that may cause
missing telegrams or transmission delays.
F236 Fault indicates that the DeviceNet Set the switch that controls the master operation for Run
Idle Master network master is in Idle mode. or the corresponding bit on the configuration word of the
master software. If further information is needed, refer to
the documentation of the master used.
F237 Fault that indicates that one or more Check the network master status.
DeviceNet Connection Timeout DeviceNet connections timed out. Check network installation, broken cable or fault/poor
contact on the connections with the network.
F238 It indicates that the inverter received Verify the network master status, making sure it is in the
Profibus DP Interface in Clear a command from the Profibus DP execution mode (Run).
Mode network master to enter the clear
mode.
CFW300 | 1-3

F239 It indicates an interruption in the Check if the network master is correctly configured and
Offline Profibus DP Interface communication between the Profibus operating properly.
DP network master and the inverter. Check for short-circuit or poor contact on the
The Profibus DP communication communication cables.
1 interface went into offline status. Check if the cables are not misconnected or inverted.
Check if the termination resistors with the right value were
installed only at the end of the main bus.
Check the network installation in general - cabling,
grounding.
F240 It indicates fault in the access to the Check if the Profibus DP module is correctly fitted.
Profibus DP Module Access Profibus DP communication module Hardware errors due to improper handling or installation
Fault data. of the accessory, for instance, may cause this fault. If
possible, carry out tests by replacing the communication
accessory.
F247 It indicates interruption in the cyclic Check the status of the network master.
EtherNet/IP Communication communication with EtherNet/IP Check the network installation, broken cable or failed/bad
Offline master. contact in the network connections.
It occurs when, for any reason, after
the cyclic communication of the master
with the product is started, this
communication is interrupted.
F249 It indicates that the device stopped Check network installation, broken cable or fault/poor
Timeout Modbus TCP receiving valid telegrams for a period contact on the connections with the network, grounding.
longer than the setting in P868. Ensure the Modbus TCP client always sends telegrams to
The time counting starts as soon as it the equipment in a time shorter than the setting in P868.
receives the first valid telegram. Disable this function in P868.
A700 No communication with remote HMI, Check if the communication interface with the HMI is
Remote HMI Communication but there is no frequency command or properly configured in parameter P312.
reference for this source. HMI cable disconnected.
F701 No communication with the remote Check that the HMI communication interface is properly
Remote HMI Communication HMI; however, there is command or configured in parameter P312.
Fault frequency reference for this source. HMI cable disconnected.
A702 This failure occurs when there is a Check if the drive General Enable command is active.
Inverter Disabled SoftPLC movement block active and
the “General Enable” command is
disabled.
A704 It occurs when 2 or more SoftPLC Check the user’s program logic.
Two Movem. Enabled movement blocks are enabled at the
same time.
A706 This failure occurs when a SoftPLC Check the programming of the references in the Local
Refer. Not Progr. SPLC movement block is enabled and the and/or Remote mode (P221 and P222).
speed reference is not programmed for
the SoftPLC.
A708 SoftPLC Application not running. SoftPLC Application is stopped (P901 = 0 and P900 = 3).
SoftPLC Application Stopped SoftPLC state presents application incompatible with the
firmware version of the frequency inverter.
F709 SoftPLC application not running. SoftPLC application stopped (P901 = 0 and P900 = 3).
SPLC Application Stopped SoftPLC state presents incompatible application with the
firmware version of the frequency inverter.
F710 The size of the SoftPLC user’s The logic implemented on the SoftPLC is too large. Check
Size of the SoftPLC Application program exceeded the maximum project size.
memory capacity.
F711 Fault found in SoftPLC user’s SoftPLC user’s program stored on flash memory is
Fault on SoftPLC Application program. corrupted.
Timeout during execution of SoftPLC scan cycle.
A712 It occurs when there is an attempt Attempt to copy SoftPLC application protected against
SPLC Protected Against Copy to copy the SoftPLC application copies (“never permit copies”).
protected against copies. Attempt to copy SoftPLC from a copy protected against
copies (“no permission to copy from a copy”).
F750/A750 to Fault/Alarm range intended for the Defined by the user’s application developed in the SoftPLC
F799/A799 user’s application developed in the function.
User’s Faults/Alarms for SoftPLC function.
SoftPLC
1-4 | CFW300
Faults and Alarms for PID Controller Application (P903 = 1)

A750 It indicates that the PID Controller is in The motor speed remained below the value programmed in
Sleep Mode Active the sleep mode. P938 for the time programmed in P939.
1
A760 It indicates that the level of the control The control process variable (P916) remained below the
Low Level of the Control process variable (P916) is low. value programmed in P924 for 150 ms.
Process Variable
F761 It indicates the motor was switched The control process variable (P916) remained below the
Low Level of the Control off due to the low level of the control value programmed in P924 for a certain time (P925).
Process Variable process variable.
A762 It indicates that the level of the control The control process variable (P916) remained above the
High Level of the Control process variable (P916) is high. value programmed in P926 for 150 ms.
Process Variable
F763 It indicates the motor was switched The control process variable (P916) remained above the
High Level of the Control off due to the high level of the control value programmed in P926 for a certain time (P927).
Process Variable process variable.
A790 It indicates that parameters of the The PID Controller was enabled, the Run/Stop command
Speed reference source not speed reference sources in local is active, and neither of the two parameters of the speed
programmed for the SoftPLC mode (P221) and in remote mode reference source was programmed in 12 (SoftPLC).
(P222) were not programmed for the
SoftPLC.
Fault and alarm operation:
Faults operate by indicating their occurrence on the HMI, in the frequency inverter status word (P006), in the
present fault parameter (P049) and disabling the motor. They can only be reset with a reset command or de-
energizing the frequency inverter.
Alarms operate by indicating their occurrence on the HMI and in the present alarm parameter (P048). They are
automatically reset when the alarm condition ceases existing.
CFW300 | 1-5
1-6 | CFW300
SAFETY NOTICES
2 SAFETY NOTICES
This manual contains the information necessary for the correct frequency inverter programming.
It was developed to be used by people with proper technical training or qualification to operate this kind of
equipment. These people must follow the safety instructions defined by local standards. The noncompliance with
the safety instructions may result in death risk and/or equipment damage.
2
2.1 SAFETY NOTICES IN THIS MANUAL
The following safety notices are used in this manual:
DANGER!
! The procedures recommended in this warning have the purpose of protecting the user against death,
serious injuries and considerable material damage.
WARNING!
! The procedures recommended in this warning have the purpose of avoiding material damage.
✓
NOTE!
The information mentioned in this warning is important for the proper understanding and good
operation of the product.
2.2 SAFETY NOTICES ON THE PRODUCT
The following symbols are attached to the product, serving as safety notices:
E High voltages are present.
Components sensitive to electrostatic discharge. Do not touch them.
Mandatory connection to the protective earth (PE).
Connection of the shield to the ground.
CFW300 | 2-1
SAFETY NOTICES
2.3 PRELIMINARY RECOMMENDATIONS
DANGER!
! Only qualified personnel familiar with the frequency inverter and associated equipment should plan or
implement the installation, start-up and subsequent maintenance of this equipment.
These personnel must follow all the safety instructions included in this manual and/or defined by local
regulations.
2 Failure to comply with these instructions may result in life threatening and/or equipment damage.
✓
NOTE!
For the purposes of this manual, qualified personnel are those trained to be able to:
1. Install, ground, energize and operate the frequency inverter according to this manual and the
effective legal safety procedures.
2. Use protective equipment according to the established standards.
3. Give first aid services.
DANGER!
! Always disconnect the input power before touching any electrical component associated to the
frequency inverter.
Many components may remain loaded with high voltages and/or moving (fans), even after the AC
power supply input is disconnected or turned off.
Wait for at least ten minutes in order to guarantee the full discharge of the capacitors. Always connect
the frame size of the equipment to the protective earth (PE) at the proper point for that.
WARNING!
! Electronic boards have components sensitive to electrostatic discharge. Do not touch directly the
component parts or connectors.
If necessary, first touch the grounded metallic frame size or use proper grounding strap.
Do not execute any applied potential test on the inverter!

If it is necessary, consult the manufacturer.
✓
NOTE!
Frequency inverters may interfere in other electronic equipments. Observe the recommendations
of chapter 3 Installation and Connection of the user’s manual in order to minimize these effects.
Read the user’s manual completely before installing or operating this inverter.
2-2 | CFW300
GENERAL INFORMATION
3 GENERAL INFORMATION
This manual presents information necessary for the configuration of all the functions and parameters of the frequency
inverter. This manual must be used together with the user’s manual.
The text provides additional information so as simplify the use and programming of the frequency inverter in certain
applications.
It is prohibited the reproduction of the contents of this manual, in whole or in part, without the written permission
of the manufacturer.
3.1 TERMINOLOGY AND DEFINITIONS 3
3.1.1 Terms and Definitions Used
Amp, A: Ampère.
AIP: analog input via potenciometer.
AIx: analog input “x”.
AOx: analog output “x”.
◦
C: Celsius degrees.
CA: alternate current.
CC: direct current.
Pre-Charge Circuit: charges the capacitors of the DC link with limited current, avoiding current peaks in the
inverter power-up.
CO/DN/PB/ETH: Interface CANopen, DeviceNet, ProfibusDP or Ethernet.
CV: cavalo-vapor = 736 Watts (Brazilian unit of measurement of power, normally used to indicate mechanical power
of electric motors).
Heatsink: metal part designed to dissipate the heat produced by power semiconductors.
DIx: digital input “x”.
DOx: digital output “x”.
Switching Frequency: switching frequency of the IGBTs of the inverter bridge, normally expressed in kHz.
Run/Stop: inverter function which, when activated (run), accelerates the motor by acceleration ramp up to the
reference frequency and, when deactivated (stop), decelerates the motor by deceleration ramp. It may be controlled
by digital input set for this function, via serial or via SoftPLC.
h: hour; time unit.
General Enable: when activated, it accelerates the motor by acceleration ramp and Run/Stop = Run. When
disabled, the PWM pulses will be immediately blocked. It may be controlled by digital input set for this function, via
serial or via SoftPLC.
HMI: human-machine interface; device which allows controlling the motor, viewing and changing the inverter
parameters. It features keys to control the motor, navigation keys and graphic LCD display.
hp: horse power = 746 Watts (power unit, normally used to indicate mechanical power of electric motors).
Hz: hertz; frequency unit.
IGBT: insulated gate bipolar transistor - basic component part of the output inverter bridge. It works as an electronic
switch in the saturated (closed switch) and cut-off (open switch) modes.
Inom : inverter rated current by P295.
kHz: quilohertz = 1000 Hertz; frequency unit.
200 V Line: Models powered from 110 to 127 Vac, 200 to 240 Vac or 280 to 340 Vdc, for more information refer
CFW300 | 3-1
GENERAL INFORMATION
to the inverter user manual.

400 V Line: Models powered from 380 to 480 Vac or 537 to 680 Vdc, for more information refer to the inverter
user manual.
DC Link: intermediary circuit of the inverter; voltage in direct current obtained by rectifying the power supply
alternate voltage or external supply; it supplies the output inverter bridge with IGBTs.
mA: miliampère = 0.001 Ampère.
min: minute; time unit.
ms: milisecond = 0.001 second.
3 Nm: Newton meter; torque unit.

NTC: resistor whose resistance value in ohms decreases proportionally to the increase of the temperature; it is
used as a temperature sensor in power packs.
PE: Protective Earth.
PTC: resistor whose resistance value in ohms increases proportionally to the temperature; it is used as a
temperature sensor in motors.
PWM: pulse width modulation - modulation by pulse width; pulsed voltage that supplies the motor.
Rectifier: input circuit of the inverters that transforms the input AC voltage into DC. It is formed by high-power
diodes.
RMS: root mean square; effective value.
rpm: revolutions per minute; rotation unit.
s: second; time unit.
V: volts; electric voltage unit.
WPS: Programming Software “WEG Programming Suite”.
Ω: ohms; electric resistance unit.
3.1.2 Numerical Representation
The decimal numbers are represented by means of digits without suffix. Parameters P012, P013, P045, P397
P680, P682, P684, P685, P690, P695, P697, P757, P758 and P840 are represented in hexadecimal numbers.
3.1.3 Symbols to Describe Parameter Properties
ro: read only parameter.

cfg: parameter that can be changed only with a stopped motor.
V/f: parameter available in the V/f mode.
VVW: parameter available in the VVW mode.
3-2 | CFW300
ABOUT THE HMI
4 ABOUT THE HMI
4.1 USE OF THE HMI TO OPERATE THE INVERTER
Using the HMI, it is possible to command the inverter, view and adjust all of its parameters. The HMI presents the
following functions:
Selects (switches) between the Enables/Disables the inverter via

parameter number and its value acceleration/deceleration ramp
(position/content). (start/stop, according to P229). Resets
the inverter after a fault.
Decreases (decrements) the Increases (increments) the

frequency, parameter number or frequency, parameter number or
parameter value. parameter value.
Figure 4.1: HMI keys
4.2 INDICATIONS ON THE HMI DISPLAY
Inverter status
Direction of rotation
Unit of measurement
(it refers to the value
of the main display)
Main display Bar Graph to monitor the variable

Figure 4.2: Display areas
4.3 OPERATING MODES OF THE HMI
When inverter is powered-up, the initial state of the HMI remains in the start-up mode as long as no faults, alarms,
undervoltages occur or no keys are pressed.
The setting mode is composed of two levels: Level 1 allows browsing the parameters. Level 2 allows the
modification of the parameter selected in level 1. At the end of this level, the modified value is saved when the
key is pressed.
A Figure 4.2 on page 4-1 illustrates the basic browsing of the operating modes of the HMI.
✓
NOTE!
When the inverter is in the fault state, the main display indicates the number of the fault in the format
Fxxx.The browsing is allowed after pressing the key.
CFW300 | 4-1
ABOUT THE HMI
Table 4.1: HMI operating modes

Start-up Mode
It is the initial status of the HMI after the successful power-up (without fault,
alarms or undervoltages)
Monitoring
Press the key to go to level 1 of the setting mode - parameter selection.
Pressing any other key will also change to the setting mode
Setting Mode
Level 1:
This is the first level of the setting mode. The number of the parameter is
shown on the main display.
Use the and keys to find the desired parameter Setting
level 1
Press the key to go to level 2 of the setting mode - modification of the
parameter content
Level 2:
The content of the parameter is shown on the main display
Use the and keys to configure the new value for the selected
parameter Setting
level 2
4 Press the key to confirm the modification (save the new value). After the
change is confirmed, the HMI returns to level 1 of the setting mode
✓
NOTE!
When the inverter is in the alarm state, the main display indicates the number of the alarm in the format
Axxx.The browsing is allowed after pressing the key, and then the indication “A” is displayed on
the unit of measurement display, flashing until the situation causing the alarm is solved.
4-2 | CFW300
HMI
5 HMI
✓
NOTE!
The inverter comes from the factory with the frequency (V/f 50/60 Hz mode) and voltage adjusted
according to the market.
The reset to factory default may change the content of the parameters related to frequency.
5.1 ACCESS
Whenever the inverter is powered up, the HMI display goes to the start-up mode if no faults, alarms or undervoltages
are present. In order to simplify the reading of the inverter parameters, the display was designed to show two
parameters simultaneously, at the user’s discretion. One of those parameters (main display) is shown in the numeric
form and the other parameter as a bar graph. The parameter monitored by the bar graph is selected via P207, as
indicated in Figure 5.1 on page 5-1.
Inverter status
5
Direction of rotation
Unit of measurement
(it refers to the value
of the main display)
Main display Bar Graph to monitor the variable

Figure 5.1: Screen on initialization and display fields
P000 - Access to Parameters
Range: 0 to 9999 Default: 1

Description:
Password input to release the access to the parameters. Once a password is saved in P200, the access to the
parameters is only allowed if this password is set in P000. After setting P000 with a password value, P000 will
show “1” or “0”, keeping the set password value hidden. Where “1” releases the access to parameters and “0”
locks the access to the parameters.
✓
NOTE!
The view of parameter P000 on the HMI will only be available when the password is active (P200 =
1).
To release the access to the parameters, it is necessary to set P000 after each inverter energization,
as such information is not retained.
P200 - Password
Range: 0 = Inactive Default: 0

1 = Active
2 to 9999 = New Password
Properties: cfg
Description:
CFW300 | 5-1
HMI
It allows activating the password (by inserting a new value) or disabling it. For further details regarding the use of
this parameter, refer to Table 5.1 on page 5-2.
Table 5.1: Required procedure for each kind of action

Action Procedure
1. Set P200 with the desired value for the password (P200 = password)
Activate password 2. The setting is completed, the new password is active and P200 is automatically adjusted for 1
(password active) (1)
1. Set the current value of the password (P000 = password)
2. Set the desired value for the new password in P200 (P200 = new password)
Change password
3. The setting is completed, the new password is active and P200 is automatically adjusted for 1
(password active) (1)
1. Set the current value of the password (P000 = password)
Disable password 2. Set inactive password (P200 = 0)
3. The setting is completed, the password is disabled (2)
1. Activate a factory default by means of P204
Disable password
2. The setting is completed, the password is disabled (2)
(1) It only allows changing the content of the parameters when P000 is equal to the value of the password.
(2) It is allowed to change the content of the parameters and P000 is inaccessible.
5
P204 - Load/Save Parameters
Range: 0 to 4 = Not Used Default: 0

5 = Load 60 Hz
6 = Load 50 Hz
7 = Load User
8 = Not Used
9 = Save User
10 = Not Used
11 = Load Default SoftPLC
12 to 13 = Reserved
Properties: cfg
Description:
The Table 5.2 on page 5-2 describes the actions performed by each option.
Table 5.2: Option of parameter P204

P204 Action
0 to 4 Not Used: no action
5 Load WEG 60 Hz: it loads the default parameters on the inverter with the factory default for 60 Hz
6 Load WEG 50 Hz: it loads the default parameters on the inverter with the factory default for 50 Hz
7 Load User: it transfers the content of the memory from user parameter to the inverter current parameters
8 Not Used: no action
9 User: transfers the current content of the parameters to the user’s parameter memory
10 Not Used: no action
11 Load Default SoftPLC: it loads the factory default in SoftPLC parameters (P910 to P959)
12 and 13 Reserved
In order to load the parameters of user for operating area of the inverter (P204 = 7) it is necessary that this area be
previously saved.
The operation of uploading this memory (P204 = 7), can also be done via digital inputs (DIx). For further details
referring to this programming, refer to Section 9.6 DIGITAL INPUTS on page 9-11.
✓
NOTE!
When P204 = 5 or 6, parameters P295 (Inv. Rated Current), P296 (Line Rated Voltage) and P308
(Serial Address) are not changed.
5-2 | CFW300
HMI
✓
NOTE!
In order to upload the user parameters (P204 = 7), the factory default must be uploaded first (P204
= 5 or 6).
5.2 INDICATIONS
P205 - Main Display Parameter

Description:
This parameter defines which parameter will be viewed on the HMI when the motor is enabled after initialization.
P207 - Bar Graph Parameter
5
Description:
This parameter defines which parameter will be shown on the HMI bar graph.
P208 - Ref. Scale Factor

Description:
This parameter allows adjusting the scale of the parameter speed reference P001 and output (motor) speed P002
so as to convert the indication of frequency values applied to the motor (Hz) into angular speed in “rpm” or a
proportional value in “%”, for instance.
Together with the unit in P209 and the decimal places in P210, the rated reference P208 defines the speed indication
on the inverter HMI. According to the factory default of those parameters, the preset scale on the inverter is in “Hz”
and with a decimal place (60.0 Hz or 50.0 Hz). On the other hand, by setting P208 = 1800 or 1500, P209 = 7 and
P210 = 0, a scale in “rpm” with no decimal places is defined (1800 rpm or 1500 rpm).
P209 - Ref. Eng. Unit
P510 - SoftPLC Eng. Unit
Range: 0 to 1 = Without unit Default: 3

2 = Volt (V)
3 = Hertz (Hz)
4 = Without unit
5 = Percent (%)
6 = Without unit
7 = Rotation/min. (rpm)
Description:
These parameters select the engineering unit that will be displayed on the HMI. P209 is linked to parameters P001
and P002. P510 is linked to the SoftPLC user’s parameters. That is, any SoftPLC user’s parameter linked to the
SoftPLC engineering unit will be dispalyed in this format.
CFW300 | 5-3
HMI
P210 - Ref. Decimal Point
P511 - SoftPLC Indication Form
Range: 0 = wxyz Default: 1

1 = wxy.z
2 = wx.yz
3 = w.xyz
Description:
This parameter allows setting the position of the decimal point displayed on the HMI. P210 is linked to the indication
of parameters P001 and P002. P511 is is linked to the indication of the SoftPLC user’s parameters. That is, any
SoftPLC user’s parameter linked to the SoftPLC indication form will be displayed in this format.
P213 - Bar Scale Factor
Range: 1 to 9999 Default: 1,0 x Inom

5
Description:
This parameter configures the full scale (100 %) of the bar graph to indicate the parameter selected by P207.
P842 - Quick View 1 IR
P843 - Quick View 2 IR

Description:
These parameters define which parameters (their respective values) will be viewed by using the key of the infrared
remote control (available with expansion module).
For further details, refer to the installation, configuration and operation guide of the expansion module.
5-4 | CFW300
FREQUENCY INVERTER IDENTIFICATION
6 FREQUENCY INVERTER IDENTIFICATION
In order to check the inverter model, see the code on the product nameplate on the side of the inverter.
Once verified the identification code of the model of the inverter, refer to Chapter 2 General Information of the user’s
manual of the frequency inverter.
The parameters related to the inverter model are shown below. They are modified according to the model and
version of the inverter and must comply with the data read on the product nameplate.
6.1 INVERTER MODEL
P023 - Main SW Version
Range: 0.00 to 99.99 Default:
Properties: ro
Description:
It indicates the software version of the main microprocessor on the control board.
P029 - Power HW Configuration 6
Range: 0 = Not identified Default: 0

1 = 1.6 A/110 V
2 = 2.6 A/110 V
3 = 4.2 A/110 V
4 = 6.0 A/110 V
5 = 1.6 A/220 V
6 = 2.6 A/220 V
7 = 4.2 A/220 V
8 = 6.0 A/220 V
9 = 7.3 A/220 V
10 = 10.0 A/220 V
11 = 15.2 A/220 V
12 to 19 = Reserved
20 = 1.1 A/380 V
21 = 1.8 A/380 V
22 = 2.6 A/380 V
23 = 3.5 A/380 V
24 = 4.8 A/380 V
25 = 6.5 A/380 V
26 = 8.2 A/380 V
27 = 10.0 A/380 V
28 = 12.0 A/380 V
29 = 15.0 A/380 V
Properties: ro
Description:
This parameter identifies the inverter model, distinguishing the supply voltage and the rated current according to
Table 6.1 on page 6-2.
From P029, the inverter determines the current and voltage parameters depending on the model identification. On
the other hand, this action is only effected at the moment of the factory standard load (P204 = 5 or 6).
CFW300 | 6-1
Table 6.1: Identification of the inverter models

Frame Size Voltage Power Supply Current P029
1.6 A 1
2.6 A 2
110 / 127 Vac Single-Phase
4.2 A 3
6.0 A 4
1.6 A 5
2.6 A 6
200 / 240 Vac Single-Phase or Three-Phase 4.2 A 7
A
6.0 A 8
7.3 A 9
1.6 A 5
2.6 A 6
310 Vdc DC Link 4.2 A 7
6.0 A 8
7.3 A 9
Single-Phase or Three-Phase 10.0 A 10
200 / 240 Vac
Three-Phase 15.2 A 11
B
10.0 A 10
310 Vdc DC Link
15.2 A 11
1.1 A 20
1.8 A 21
A 380 / 480 Vac Three-Phase 2.6 A 22
3.5 A 23
4.8 A 24
1.1 A 20
6 1.8 A 21
2.6 A 22
B 3.5 A 23
4.8 A 24
380 / 480 Vac or 513 to 650 Vdc Three-Phase or DC Link
6.5 A (*) / 5.6 A (**) 25
8.2 A (*) / 7.6 A (**) 26
10.0 A (*) / 8.3 A (**) 27
C 12.0 A (*) / 11.0 A (**) 28
15.0 A (*) / 14.0 A (**) 29
(*) Rated current for power supplies of 380-400-415 Vac.

(**) Rated current for power supplies of 440-460-480 Vac.
✓
NOTE!
The models of the 400 V line have rated currents specified according to the supply voltage:
Voltage range 1: power supplies of 380-400-415 Vac, or 513-540-560 Vdc (P296 = 4 or 5).
Voltage range 2: power supplies of 440-460-480 Vac, or 594-621-650 Vdc (P296 = 6 or 7).
For these models, P296 must be adjusted in accordance with the mains voltage used, and the
parameter P295 will be changed automatically by the inverter. For more information, refer to the
user manual, available for download on www.weg.net.
P295 - Inverter Rated Current
Range: 1.1 to 15.2 A Default: According to the

Inverter Model
Properties: ro
Description:
This parameter presents the inverter rated current according to Table 6.1 on page 6-2.
6-2 | CFW300
P296 - Line Rated Voltage
Range: 0 = Reserved Default: According to the

1 = 110 - 127 Vac Inverter Model
2 = 200 - 240 Vac | 310 Vdc
3 = Reserved
4 = 380 Vac | 513 Vdc
5 = 415 Vac | 560 Vdc
6 = 440 Vac | 594 Vdc
7 = 480 Vac | 650 Vdc
Properties:
Description:
This parameter shows the inverter supply voltage according to the identification made after power up (and for
models of the 400 V Line, after adjustment).
✓
NOTE!
200 V Line: P296 is read-only parameter (ro). 400 V Line: P296 is configuration parameter (cfg). For
further information, refer to the user’s manual, available for download on: www.weg.net.
P613 - Main SW Revision 6
Range: -9999 to 9999 Default:
Properties: ro
Description:
This parameter is a counter that indicates the software revision. It is automatically generated by the machine that
compiled the firmware.
6.2 ACCESSORIES
P024 - IO Acces. SW Version
P025 - Comm. Acces. SW Version
Properties: ro
Description:
They indicate the software versions of the connected microprocessors according to parameters P027 and P028.
P027 - Config. Acces. IO
P028 - Config. Comm. Acces.
Range: 0 to 10 Default:
Properties: ro
Description:
CFW300 | 6-3
These parameters identify the accessories that are connected according to the tables below.
Table 6.2: IO’s expansion accessories

Name Description P027
- No accessories 0
CFW300-IOAR Accessory for IO’s expansion: 1 analog input + 1 analog output + 3 relay digital outputs 1
CFW300-IODR Accessory for IO’s expansion: 4 digital inputs (NPN/PNP) + 3 relay digital outputs 2
CFW300-IOADR Accessory for IO’s expansion: 1 input for infrared receiver + 1 NTC sensor input + 3 relay digital outputs 3
CFW300-IOAENC Accessory for IO’s expansion: 1 analog input + 2 analog outputs + 1 differential encoder input 4
- Reservado 5
CFW300-IODF Accessory for IO expansion: 3 inputs and 3 outputs in frequency 6
- Reserved 7 a 10
Table 6.3: Communication expansion accessories

Name Description P028
- No accessories 0
CFW300-HMIR Remote HMI accessory (via CFW300-CRS485 accessory) 1
CFW300-CBLT Bluetooth communication accessory 2
CFW300-CCAN Accessory with communication CANopen and DeviceNet 3
CFW300-CPDP Accessory with communication Profibus DP 4
CFW300-CETH Accessory with communication Ethernet 5
- Reserved 6
CFW300-IOP Accessory for IO expansion: 1 analog input 7
6 - Reserved 8 a 10
6-4 | CFW300
COMMAND AND REFERENCES
7 COMMAND AND REFERENCES
The drive of the electric motor connected to the inverter depends on the logical command and on the reference
defined by one of the several possible sources, such as: HMI keys, digital inputs (DIx), analog inputs (AIx), Serial/
USB interface, CANopen/DeviceNet interface, SoftPLC, etc.
The command via HMI is limited to a set of functions pre-defined for the keys according to Chapter 5 HMI on page
5-1, similarly to the digital inputs (DIx), with the functions implemented in parameter P263 to P266. On the other
hand, the command via digital interfaces, such as communication network and SoftPLC, act directly on the inverter
control word by means of control parameters and system markers of the SoftPLC, respectively.
The frequency reference, in turn, is processed inside the frequency inverter in 16 bits with signal (-32768 to +32767)
for a range of -400.0 Hz to +400.0 Hz. On the other hand, the unit factor, range and resolution of the reference
depend on the used source, as described in Section 7.2 SPEED REFERENCE on page 7-6.
7.1 REFERENCE SOURCE SELECTION
The inverter command and reference source is defined by the inverter parameters for two different situations: Local
and Remote, which can be switched dynamically during the inverter operation. Thus, for a certain parameterization,
the inverter has two sets for command and reference, according to block diagram of Figure 7.1 on page 7-2.
Parameter P220 determines the source of commands for Local and Remote situations.
Parameters P223, P224 and P225 define the commands in the Local situation; parameters P226, P227 and P228
define the commands in the Remote situation, and parameter P105 determines the source for selection between
1st and 2nd Ramp. This structure for the selection of the command source is shown in Figure 7.1 on page 7-2.
Parameters P221 and P222 define the frequency reference in the Local and Remote situations. This structure for
the selection of the reference source is shown in Figure 7.2 on page 7-3.
7
CFW300 | 7-1
Direction of
rotation
P223
Run/
Stop
P224
Control
LOC
P225
JOG
word
Control word
Direction of
REM
rotation Control
P226
word
Run/
P227
Stop
P228
JOG
All the command and

reference sources
of the Inverter
LOC/REM
7
P220
2nd Ramp
P105
Reference
P221
LOC
frequency
Reference frequency
Reference
REM
P222
frequency
Figure 7.1: Block diagram for commands and references
7-2 | CFW300
Command
selection
frequency
HMI P221 or P222
Reference
HMIR key (P121) 0 - HMI
CRS485
Accessory
FI
via
7 - EP
DI1 to DI4 P247
P249
Accel.
DIx
Decel. 4 - FI
DIx
17 - FI > 0
Electronic potentiometer Frequency
reference of
P124 to P131 the inverter
DIx
DIx
8 - Multispeed
DIx
Multispeed
AI1
1 - AI1
P232 14 - AI1 > 0
P234
5 - AI1 + AI2 > 0
7
6 - AI1 + AI2
AI2
2 - AI2
P237 15 - AI2 > 0
P239
Potentiometer
P242 3 - Potentiometer
P244 16 - Potentiometer > 0
CRS232
PC Accessory
9 - Serial/USB
CUSB
Accessory
USB - RS485 CRS485

Converter Accessory
Bluetooth CBLT
adapter Accessory
CANopen / DeviceNet
CCAN / CPDP / CETH-IP
Profibus DP
Accessory
ModbusTCP / Ethernet-IP 11 - CO/DN/DP/ETH
SoftPLC
12 - SoftPLC
Figure 7.2: Structure to select the frequency reference
CFW300 | 7-3
P220 - LOC/REM Selection Source
Range: 0 = Always Local Default: 0

1 = Always Remote
2 to 3 = Not Used
4 = DIx
5 = Serial/USB (LOC)
6 = Serial/USB (REM)
7 to 8 = Not Used
9 = CO/DN/DP/ETH (LOC)
10 = CO/DN/DP/ETH (REM)
11 = SoftPLC
Properties: cfg
Description:
It defines the command origin source which will select between Local situation and Remote situation, where:
LOC: means Local situation default.
REM: means Remote situation default.
DIx: according to function programmed for digital input in P263 to P266.
CO / DN / DP / ETH: interface CANopen, DeviceNet, Profibus DP or Ethernet.
P221 - LOC Reference Sel.

7
P222 - REM Reference Selection
Range: 0 = HMI Default: 0

1 = AI1
2 = AI2
3 = Potentiometer
4 = FI
5 = AI1 + AI2 > 0
6 = AI1 + AI2
7 = E.P.
8 = Multispeed
9 = Serial/USB
10 = Not Used
11 = CO/DN/DP/ETH
12 = SoftPLC
13 = Not Used
14 = AI1 > 0
15 = AI2 > 0
16 = Potentiometer > 0
17 = FI > 0
Properties: cfg
Description:
These parameters define the origin source for the frequency reference in the Local situation and Remote situation.
Some comments on the options of this parameter:
AIx: it refers to the analog input signal according to Section 9.1 ANALOG INPUTS on page 9-1.
HMI: the reference value set by the keys and are contained in parameter P121.
7-4 | CFW300
E.P.: electronic potentiometer, refer to Section 9.6 DIGITAL INPUTS on page 9-11.
Multispeed: refer to Section 9.6 DIGITAL INPUTS on page 9-11.
AIx > 0: the negative values of the AIx reference are zeroed.
P223 - LOC FWD/REV Selection
P226 - REM FWD/REV Selection
Range: 0 = Forward Default: 0

1 = Reverse
2 to 3 = Not Used
4 = DIx
5 = Serial/USB (FWD)
6 = Serial/USB (REV)
7 to 8 = Not Used
9 = CO/DN/DP/ETH (FWD)
10 = CO/DN/DP/ETH (REV)
11 = Not Used
12 = SoftPLC
Properties: cfg
Description: 7
They define the origin source for the “Direction of Rotation” command in the Local and Remote situation, where:
H: means Forward.
AH: means Reverse.
DIx: refer to Section 9.6 DIGITAL INPUTS on page 9-11.
P224 - LOC Run/Stop Sel.
P227 - REM Run/Stop Selection
Range: 0 = HMI Keys Default: 0

1 = DIx
2 = Serial/USB
3 = Not Used
4 = CO/DN/DP/ETH
5 = SoftPLC
Properties: cfg
Description:
These parameters define the origin source for the “Run/Stop” command in the Local and Remote situation. This
command corresponds to the functions implemented in any of the command sources able to enable the motor
movement, that is, General Enable, Ramp Enable, Forward Run, Reverse Run, Start, etc.
P225 - LOC JOG Selection
CFW300 | 7-5
P228 - REM JOG Selection
Range: 0 = Disabled Default: 1

1 = Not Used
2 = DIx
3 = Serial/USB
4 = Not Used
5 = CO/DN/DP/ETH
6 = SoftPLC
Properties: cfg
Description:
They define the origin source for the JOG function in the Local and Remote situation. The JOG function means a
Run/Stop command added to the reference defined by P122. Refer to Section 7.2 SPEED REFERENCE on page
7-6.
P229 - Stop Mode Selection
Range: 0 = Ramp to Stop Default: 0

1 = Coast to Stop
Properties: cfg
Description:
This parameter defines the motor stop mode when the inverter receives the “Stop” command. Table 7.1 on page
7-6 describes the options of this parameter.
7
Table 7.1: Selection of stop mode
P229 Description
0 The inverter will apply the stop ramp programmed in P101 or P103
1 The motor will run free until it stops
✓
NOTE!
When the Coast Stop mode is programmed and the Flying Start function is disabled, only activate
the motor if it is stopped.
✓
NOTE!
This parameter is applied to all the inverter command sources, but it was created aiming at allowing
the command via HMI to be able to disable the motor by inertia instead of deceleration ramp. In this
way, when P229 = 1, Bit 0 of the control word (Ramp Enable) has a function similar to Bit 1 (General
Enable). The same way, the digital input functions such as: Run/Stop, Forward/Reverse Run stop
the motor by inertia in this condition of P229.
7.2 SPEED REFERENCE
The frequency reference is the value applied to the input of the acceleration ramp module (P001) to control the
frequency applied to the inverter output (P002) and consequently the motor shaft speed.
Inside the CPU, the inverter uses signed 16 bit variables to treat the frequency references. Besides, the full scale of
the reference, output frequency and related variables are defined in 400.0 Hz. On the other hand, depending on the
source, this scale is conveniently modified considering the interface with the user by standardization or application
requirements.
In general, the digital references defined by parameters such as: HMI keys (P121), Multispeed (P124 to P131) and
7-6 | CFW300
E.P. have a scale from 0.0 to 400.0 Hz with resolution of 0.1 Hz.
In digital inputs (DIx), on the other hand, the reference is defined according to the function predefined for P263 to
P266.
The frequency reference applied to the inverter output via frequency input follows the behavior of the parameters
related to it (P230 to P250).
The full scale of the reference is always by P134, that is, maximum value in AIx is equivalent to the frequency
reference equal to P134.
The digital references Serial/USB, CANopen/DeviceNet, Profibus DP, Ethernet and SoftPLC act on a standardized
scale called “13-bit speed”, where the value 8192 (213 ) is equivalent to the motor rated frequency (P403).
Those references are accessed by parameters P683 and P685.
The digital references, though, have a different scale and the frequency reference parameters with their range from
0.0 to 400.0 Hz, according to previous descriptions, the frequency value on the ramp input (P001) is always limited
by P133 and P134.
For example, the JOG reference is given by P122, this parameter may be set in up to 400.0 Hz, but the value
applied to the ramp input as reference will be limited by P134 when the function is executed.
Table 7.2: Summary of the scales and resolutions of the frequency references
Reference Full Scale Resolution
Analog input (AIx) -P134 to P134 10 bits or (P134/1024)
Communication Networks and SoftPLC -400.0 Hz to 400.0 Hz 13-Bit Speed (P403/8192)
HMI Parameter -400.0 Hz to 400.0 Hz 0.1 Hz
P120 - Speed Ref. Backup 7

1 = Active
2 = Backup by P121
Description:
This parameter defines the operation of the backup function of the speed reference from one of the options Inactive
(P120 = 0), Active (P120 = 1) and by P121 (P120 = 2). This function, in turn, determines the form of backup of the
digital references of the sources: HMI (P121), E.P. and Serial (P683), according to Table 7.3 on page 7-7.
Table 7.3: Options of parameter P120

P120 Reference Initial Values at the Enabling or Power-Up
0 Value of P133
1 Last adjusted value
2 Value of P121
If P120 = Inactive, the inverter will not save the speed reference value when it is disabled. Thus, when the inverter
is enabled again, the speed reference value will become the frequency minimum limit value (P133).
If P120 = Active, the value set in the reference is not lost when the inverter is disabled or powered down.
If P120 = Backup by P121, the reference initial value is fixed by P121 at the enabling or power-up of the inverter.
P121 - Reference via HMI
Range: 0.0 to 400.0 Hz Default: 3.0 Hz

Description:
Parameter P121 stores the frequency reference via HMI (P221 = 0 or P222 = 0). When the and keys are
active and the HMI in the monitoring mode, the value of P121 is increased and shown on the HMI main display.
CFW300 | 7-7
Besides, the P121 is used as input for the reference backup function.
✓
NOTE!
The minimum and maximum values of parameter setting are limited by P134 and P133, respectively.
P122 - JOG Reference
Range: -400.0 to 400.0 Hz Default: 5.0 Hz

Description:
During the JOG command, the motor accelerates up to the value defined in P122, following the acceleration ramp
set according to P105. This command may be activated by any of the sources, as per Section 7.1 REFERENCE
SOURCE SELECTION on page 7-1. The negative values determine a direction of rotation opposite to that defined
by the inverter command word.
P124 - Multispeed Ref. 1

7
Range: -400.0 to 400.0 Hz Default: 3.0 Hz

Description:
By the combination of up to three digital inputs, one from eight levels that form the multispeed reference is selected.
Read the description of the of the digital inputs in Section 9.6 DIGITAL INPUTS on page 9-11, as well the reference
selection in Section 7.1 REFERENCE SOURCE SELECTION on page 7-1. The negative values determine a direction
of rotation opposite to that defined by the inverter command word (bit 2 of P682).
Figure 7.3 on page 7-9 and Table 7.4 on page 7-9 show the operation of the Multispeed. Although the most
significant digital input may be set at DI1 or DI2, only one of those options is allowed; otherwise, the Config state
(ConF), according to Table 11.3 on page 11-5, is activated to indicate parameterization incompatibility.
7-8 | CFW300
Table 7.4: Multispeed frequency reference

8 Referency
4 Referency
2 Referency
DI1 or DI2 or DI5 or DI6 DI3 or DI7 DI4 or DI8 Frequency Reference
Inactive Inactive Inactive P124
Inactive Inactive Active P125
Inactive Active Inactive P126
Inactive Active Active P127
Active Inactive Inactive P128
Active Inactive Active P129
Active Active Inactive P130
Active Active Active P131
Output
P131
frequency
P130
P129
P128
Acceleration
P127 ramp
7
P126
P125
P124
Time
Active
DI1 or DI2
Inactive
DI5 or DI6
Active
DI3 or DI7 Inactive
Active
DI4 or DI8 Inactive
Figure 7.3: Operating graph of the Multispeed function
P133 - Minimum Frequency
P134 - Maximum Frequency

Description:
Limits for frequency reference of the inverter. These limits are applied to any reference source, even in case of
“13-bit speed”.
CFW300 | 7-9
7-10 | CFW300
MOTOR CONTROL
8 MOTOR CONTROL
The inverter feeds the motor with variable voltage, current and frequency, providing control of the motor speed.
The values applied to the motor follow a control strategy, which depends on the selected type of motor control and
on the inverter parameter settings.
The selection of the proper control type for the application depends on the static and dynamic requirements of torque
and speed of the driven load, that is, the control type is directly connected to the required performance. Additionally,
proper configuration of the selected control mode parameters is essential to reach maximum performance.
The inverter is equipped with three control modes for the three-phase induction motor, that is:
V/f Scalar Control: for basic applications without output speed control.
Quadratic V/f Scalar Control: for applications that reduce motor and inverter losses without regulation of the
output speed.
VVW Control: for applications that need high performance in the control of the output speed.
Section 8.2 CONTROLE ESCALAR V/f on page 8-18 and Section 8.3 CONTROLE VVW on page 8-26, each of
these kinds of control, related parameters and directions regarding the use of each of these modes are described
in details.
P202 - Type of Control
Range: 0 = V/f Default: 0

1 = Quadratic V/f
2 to 4 = Not Used
5 = VVW
Properties: cfg
Description: 8
This parameter selects the kind of three-phase induction motor control used.
8.1 COMMON FUNCTIONS
This chapter describes the functions common to all inverter control modes V/f and VVW and that interfere in the
drive performance.
8.1.1 Ramps
The inverter ramp functions allow the motor to accelerate or decelerate faster or slower. They are adjusted by
parameters that define the linear acceleration time between zero and the maximum frequency (P134) and the time
for a linear deceleration from the maximum frequency zero.
In the inverter, three ramps with different functions were implemented:
1st Ramp - standard for most functions.
2nd Ramp - it may be activated by the user, according to the drive requirement, by means of the inverter command
word or by a digital input.
emergency ramp - it is used for the inverter internal protection functions, such as: current limitation, DC link
regulation, etc. The Emergency Ramp has priority over the other ramps.
✓
NOTE!
The setting with too short ramp time may cause overcurrent in the output (F070), undervoltage (F021)
or overvoltage (F022) of the DC link.
CFW300 | 8-1
MOTOR CONTROL
P100 - Acceleration Time
P101 - Deceleration Time
P102 - Acceleration Time 2nd Ramp
P103 - Deceleration Time 2nd Ramp
P106 - Emer. R. Acceleration Time
P107 - Emer. R. Time Deceleration
Range: 0.1 to 999.9 s Default: 5.0 s

Description:
Acceleration and deceleration times according to the active ramp (standard, 2nd ramp or emergency ramp).
P104 - Ramp S

1 = Active
Properties: cfg
Description:
This parameter allows the inverter acceleration and deceleration ramps to have a non-linear profile, similar to an
“S”, aiming at reducing the mechanical shocks on the load, as shown in Figure 8.1 on page 8-2.
8
Output
frequency
Linear ramp
Ramp S t(s)
Acceleration time Deceleration time

(P100/P102) (P101/P103)
Figure 8.1: S or Linear ramp
8-2 | CFW300
MOTOR CONTROL
P105 - 1st / 2nd Ramp Selection
Range: 0 = 1st Ramp Default: 0

1 = 2nd Ramp
2 = DIx
3 = Serial/USB
4 = Reserved
5 = CO/DN/DP/ETH
6 = SoftPLC
Description:
It defines the origin source of the command to select between the first and second Ramp.
Note: Parameter P680 (Logical Status) indicates if the 2nd Ramp is active or not. For further information on this
parameter, refer to Chapter 11 READ on page 11-1.
8.1.2 Regulation
The DC link voltage and output current limitation are protection functions of the inverter which act on the ramp
control, aiming at containing the rise of voltage on the DC link and of the output current. In this way, the following
of the reference by the ramp is blocked and the output frequency follows the emergency ramp for a preset safety
value.
When the DC link voltage is too high, the inverter may freeze the deceleration ramp. On the other hand, when
the output current is too high, the inverter may decelerate or freeze the acceleration ramp in order to reduce this
current. Those actions prevent the occurrence of faults F022 and F070, respectively.
Both protections normally occur at different moments of the inverter operation, but in case of occurrence at the
same time, by definition, the DC link limitation has higher priority than the output current limitation.
The voltage limitation on the DC link during braking actuates limiting the braking power and torque, so as to prevent
the shutting down of the inverter for overvoltage (F022). This situation often occurs when a load with high moment 8
of inertia is decelerated or when short deceleration time is programmed.
P150 - DC/LC Regul. Type
Range: 0 = hold_Ud and decel_LC Default: 0

1 = accel_Ud and decel_LC
2 = hold_Ud and hold_LC
3 = accel_Ud and hold_LC
Properties: cfg, V/f, VVW
Description:
P150 configures the behavior of the ramp for the limitation functions of the DC Link Voltage and Current Limitation.
In those cases, the ramp ignores the reference and takes an action of accelerating (accel), decelerating (decel) or
freezing (hold) the normal path of the ramp. That occurs because of the limit pre-defined in P151 and P135 for the
DC Link (Ud) Limitation and for Current (LC) Limitation, respectively.
8.1.2.1 DC Link Voltage
The voltage limitation of the DC Link may work in two ways:
8.1.2.1.1 DC Link Voltage Limitation by “Ramp Hold” (P150 = 0 or 2)

It has effect during deceleration only.
Actuation: when the DC link voltage reaches the level set in P151, a command is sent to the “ramp” block, which
inhibits the motor frequency variation according to Figure 8.12 on page 8-19 and Figure 8.20 on page 8-27.
CFW300 | 8-3
MOTOR CONTROL
Use recommended in the drive of loads with high moment of inertia referred to the motor shaft or loads that
require short deceleration ramps.
8.1.2.1.2 DC Link Voltage Limitation by “Accelerate Ramp” (P150 = 1 or 3)

It has effect in any situation, regardless the motor frequency condition: accelerating, decelerating or constant
frequency.
Actuation: when the DC link voltage reaches the level set in P151, a command is sent to the ramp block to
accelerate the motor.
Use recommended for the drive of loads that require braking torques at constant frequency in the inverter output.
For example, the drive of loads with eccentric shaft as in sucker rod pumps; another application is the handling
of loads with balance like in the translation in overhead cranes.
P149 - DC Link Comp. Mode

1 = Standard
2 = Overmodulation
3 = Extended
Properties: cfg, V/f
Description:
The voltage of the capacitor bank (or DC Link) originates from the voltage of the rectified supply line. The value
of this voltage varies according to the characteristics of the power line where the inverter is installed and the load
requirements of the motor driven by the inverter.
The value of the output voltage (voltage applied to the motor) is directly related to the DC Link voltage through the
modulation index. The modulation index is defined as a ratio between the fundamental component amplitude in
8 the inverter phase output voltage and the DC link voltage.
Thus, variations in the supply line voltage affect the DC Link voltage, which cause variations in the output voltage,
as shown in Figure 8.2 on page 8-4, preventing the output voltage from reaching its maximum value.
DC link voltage ( % Vdc) Output Voltage ( % Vac)
Figure 8.2: Influence of the DC Link in the output voltage
Another condition that prevents the output voltage from reaching its maximum value is internal losses of the inverter.
Such losses are associated to the dead time of the switching and losses in the components, being aggravated by
the increase of the switching frequency.
8-4 | CFW300
MOTOR CONTROL
Such conditions, variations in the DC Link voltage and internal losses can be compensated with variations in the
modulation index; however, with specific characteristics as presented in each of the options below:
P149 = 0 (Disabled): The DC link compensation is disabled. The DC link voltage oscillations will reflected in the
output voltage.
P149 = 1 (Standard): In this mode, the output voltage will be generated according to the ideal V/f profile,
parameterized in P142, P143, P145 and P146, but not reaching the maximum available voltage at the output
and also not generating distortions in the output voltage.
P149 = 2 (Overmodulation): When selecting this option the output voltage will also be generated according to
the ideal V/f profile, parameterized in P142, P143, P145 and P146, but the maximum available voltage can be
generated. On the other hand, distortions in the output voltage may occur.
P149 = 3 (Extended): This option works similarly to option 2 (overmodulation). However, in the event of a DC
link voltage drop of approximately 20 % of the rated voltage, the function may take two different actions:
1. If the torque demand is low, it reduces the voltage applied to the motor, also reducing the motor current,
allowing to maintain the application, or;
2. If the torque demand is high, it reduces the output frequency until it is possible to generate a voltage according
to the V/f profile.
Both cases have restrictions of use according to the final application, and the user is responsible for validating the
application.
✓
NOTE!
It is recommended to use extended DC link voltage compensation mode (P149 = 3) for quadratic
torque applications (blowers, fans, pumps and compressors).
WARNING! 8
! The use of the DC link voltage compensation options does not compensates for all internal losses of
the inverter, and it is not intended to increase the performance in installations that do not observe the
recommendations in the product user’s manual.
P151 - DC Link Regul. Level
Range: 325 to 810 V Default: 430 V (P296 = 1)

380 V (P296 = 2)
781 V (P296 = 4)
781 V (P296 = 5)
781 V (P296 = 6)
781 V (P296 = 7)
Properties: V/f, VVW
Description:
Voltage level to activate the DC link voltage regulation.
Table 8.1: Actuation Level of the voltage regulation

Input Voltage P151 Actuation Band P151 (factory default)
100 to 127 Vac 391 to 460 Vdc 430 Vdc
200 to 240 Vac 349 to 410 Vdc 380 Vdc
380 Vac 621 to 781 Vdc 781 Vdc
415 Vac 646 to 781 Vdc 781 Vdc
440 Vac 716 to 781 Vdc 781 Vdc
480 Vac 747 to 781 Vdc 781 Vdc
CFW300 | 8-5
MOTOR CONTROL
Figure 8.3 on page 8-6 shows the block diagram of the actuation of the limitation. Figure 8.4 on page 8-6 and
Figure 8.5 on page 8-7 show the example chart.
Ramp
P100-P104
Reference Output frequency
P101 P002
Hold
P004 + ≥0
-
P151
Figure 8.3: Block diagram DC Link voltage limitation
Ud DC Link voltage (P004)
F022 - overvoltage
P151 DC Link
Ud rated regulation
8 Time
Output
frequency
Time
Figure 8.4: Example graph of DC Link voltage limitation - Ramp Hold (P150 = 2 or 3)
8-6 | CFW300
MOTOR CONTROL
Ud DC Link voltage (P004)
F022 - overvoltage
P151 DC Link
Ud rated regulation
Time
Output
frequency
Time
Figure 8.5: Example graph of the DC Link voltage limitation - Accelerate Ramp (P150 = 0 or 1)
8.1.2.2 Output Current
Like in the DC Link voltage regulation, the output current regulation also has two operating modes: “Ramp Holding”
(P150 = 2 or 3) and “Decelerate Ramp” (P150 = 0 or 1). Both actuate limiting the torque and power delivered to the
motor, so as to prevent the shutting down of the inverter by overcurrent (F070). This situation often occurs when a
load with high moment of inertia is accelerated or when short acceleration time is programmed.
8.1.2.2.1 Output Current Limitation by “Ramp Hold” (P150 = 2 or 3) 8

It prevents the motor from collapsing during torque overload in the acceleration or deceleration.
Actuation: if the motor current exceeds the value set in P135 during acceleration or deceleration, the frequency
will not be incremented (acceleration) or decremented (deceleration). When the motor current reaches a value
below P135 the motor accelerates or decelerates again. Refer to Figure 8.6 on page 8-8.
It has a faster action than the “Decelerate Ramp” mode.
It acts in the motorization and regeneration modes.
8.1.2.2.2 Current Limitation Type “Decelerate Ramp” (P150 = 0 or 1)

It prevents the motor from collapsing during torque overload in the acceleration or constant frequency.
Actuation: if the motor current exceeds the value set in P135, a null value is forced for the frequency ramp input
forcing the motor deceleration. When the motor current reaches a value below P135 the motor accelerates again.
Refer to Figure 8.6 on page 8-8.
P135 - Maximum Output Current
Range: 0.0 to 40.0 A Default: 1,5 x Inom

Properties: V/f
Description:
Current level to activate the current limitation for the Ramp Hold and Decelerate Ramp modes, as per Figure 8.6
on page 8-8 (a) and (b), respectively. In order to disable the current limitation, you must set parameter P135 > 1.9
x Inom .
CFW300 | 8-7
MOTOR CONTROL
Motor current Motor current
P135 P135
Time Time
Output Output
frequency frequency
Ramp
deceleration
Ramp (P101)
acceleration
(P100) Time Time
During Acceleration During Deceleration
(a) “Ramp Hold”
Motor current
P135
Time
Output
frequency
It decelerates
by emergency
ramp
8 Time
(b) “Ramp Deceleration”

Figure 8.6: (a) and (b) Actuation modes of current limitation via P135
P139 - Output Current Filter

Description:
Time constant of the filter for the total and active output current. You must consider a filter response time equal to
three times the time constant set in P139.
8.1.2.3 Switching Frequency
P219 - Red. Switch. Freq.

Properties: cfg
Description:
It defines the point at which automatic gradual reduction of the switching frequency occurs. That significantly
improves the measurement of the output current at low frequencies and consequently the performance of the
8-8 | CFW300
MOTOR CONTROL
inverter.
✓
NOTE!
Both the function related to P219 and the function controlled by P397 (bit 3) act by reducing the
switching frequency. As the function related to P219 is intended to improve the reading of the inverter
current, that function has priority of action over the function controlled by P397 (bit 3).
P297 - Switching Frequency
Range: 2.5 to 15.0 kHz Default: 5.0 kHz

Properties: cfg, V/f, VVW
Description:
You can use this parameter to define the inverter IGBT switching frequency.
The inverter switching frequency may be adjusted according to the application needs. Higher switching frequencies
imply less acoustic noise in the motor. However, the switching frequency choice results in a compromise among
the acoustic noise in the motor, the inverter IGBT losses and the maximum permitted currents.
The reduction of the switching frequency reduces the effects related to the motor instability, which occurs in certain
application conditions. Besides, it reduces the earth leakage current, preventing the actuation of the faults F070
(output overcurrent or short-circuit).
8.1.3 Flying Start / Ride-Through
The Flying Start function allows driving a motor that is in free running, accelerating it from the rotation in which it is.
The Ride-Through function allows recovering the inverter, with no locking by undervoltage, when there is an instant
drop in the power supply.
Both functions assume the special case in which the motor is running in the same direction and at a frequency close 8
to the frequency reference, thus, by immediately applying the frequency reference to the output and increasing the
output voltage in ramp, the slip and the starting torque are minimized.
P320 - Flying Start / Ride-Through

1 = Flying Start
2 = FS / RT
3 = Ride-Through
Properties: cfg
Description:
Parameter P320 selects the use of the Flying Start and Ride-Through functions.
Flying Start Function (FS): In order to activate this function, just program P320 in 1 or 2; thus the inverter will
impose a fixed frequency at the start, defined by the frequency reference, and apply the voltage ramp defined in
parameter P331. In this way, the start current is reduced. On the other hand, if the motor is at rest, the frequency
reference and the real frequency of the motor are very different or the direction of rotation is inverted; the result in
such cases may be worse than the conventional start without Flying Start.
The Flying Start function is applied on loads with high inertia or systems that require start with the motor spinning.
Besides, the function may be deactivated dynamically by a digital input P263 to P266 programmed for “24
= Disable Flying Start”. In this way, the user may activate the function in a convenient way according to the
application.
Ride-Through Function (RT): The Ride-Through function will disable the inverter output pulses (IGBT) as soon
as the supply voltage reaches a value below the undervoltage value. A fault due to undervoltage (F021) does not
CFW300 | 8-9
MOTOR CONTROL
occur and the DC link voltage will slowly drop until the supply voltage returns. In case it takes the supply voltage
too long to return (over 2 seconds), the inverter may indicate F021 (undervoltage on the DC link). If the supply
voltage returns before, the inverter will enable the pulses again, imposing the frequency reference instantly (like
in the Flying Start function) and making a voltage ramp with time defined by parameter P331. Refer to Figure 8.7
on page 8-10.
Return line
DC Link
voltage
Level F021
tdisab. > tdead Enabled

Output pulses
P331
Output voltage
Disabled
0V
Output
frequency (P002)
0 Hz
Figure 8.7: Actuation of the Ride-Through function
The Ride-Through function allows recovering the inverter without locking by undervoltage F021 for momentary
power supply drops. The time interval accepted during a fault is at most two seconds.
P331 - Voltage Ramp for FS and RT

8
Description:
This parameter determines the rising time of the output voltage during the execution of the Flying Start and Ride-
Through functions.
P332 - Dead Time

Description:
Parameter P332 sets the minimum time the frequency inverter will wait until driving the motor again with the Ride
Through function, which is necessary to demagnetize the motor.
8.1.4 DC Braking
The DC Braking allows stopping the motor by applying direct current to it. The current applied at the DC Braking is
proportional to the braking torque and may be set in P302. It is set in percentage (%) of the inverter rated current
considering the motor of power compatible with the inverter.
P299 - DC Braking Start Time

8-10 | CFW300
MOTOR CONTROL
Description:
DC braking duration at the start.
Output frequency
Time
Direct current
injection at start
P299
P302
DC braking
Time
Run
Stop
Figure 8.8: DC Braking actuation at start
P300 - DC Braking Stop Time

Description:
DC Braking duration at the stop.Figure 8.9 on page 8-11 shows the braking behavior at the stop.
Injection of 8
DC current
Output P300
frequency
P301
Time
Active
DIx - Run/Stop
Inactive
Figure 8.9: DC Braking actuation at the stop with command
During the braking process, if the inverter is enabled, the braking is interrupted and the inverter will start operating
normally.
WARNING!
! The DC Braking can continue acting even if the motor has already stopped. Be careful with the
thermal dimensioning of the motor for short-period cyclic braking.
P301 - DC Braking Frequency

Description:
CFW300 | 8-11
MOTOR CONTROL
This parameter establishes the initial point to apply the DC Braking at the stop when the inverter is disabled by
ramp, according to Figure 8.9 on page 8-11.
P302 - DC Braking Current
Range: 0.0 to 100.0 % Default: 20.0 %

Description:
This parameter sets the DC current (DC braking torque) applied to the motor during the braking.
The setting must be done by gradually increasing the value of P302, which varies from 0.0 to 100.0 % of the rated
braking voltage, until the desired braking is obtained.
If the inverter has a power too much higher than the motor, the braking torque will be too low. On the other hand, if
the opposite is true, overcurrent may occur during the braking, as well as overheating of the motor. A value too high
in P302 may cause overcurrent faults on the inverter and even damages to the connected motor by overcurrent on
the windings.
✓
NOTE!
A value too high in P302 may cause overcurrent faults on the inverter and even damages to the
connected motor by overcurrent on the windings.
8.1.5 Dynamic Braking
The braking torque that can be obtained through the application of frequency inverters without dynamic braking
resistors varies from 10 % to 35 % of the motor rated torque.
In order to obtain higher braking torques, resistors for dynamic braking are used. In this case the regenerated
8 energy is dissipated on the resistor mounted externally to the inverter.
This type of braking is used in the cases when short deceleration times are wished or when high inertia loads are
driven.
✓
NOTE!
The Dynamic Braking function can only be used if a braking resistor has been connected to the
inverter, and if the parameters related to it have been adjusted properly.
P153 - Dynamic Braking Level
Range: 348 to 800 V Default: According to the

Inverter Model
Description:
The parameter P153 defines the voltage level for the braking IGBT actuation, and it must be compatible with the
power supply voltage.
If P153 is set at a level too close to the overvoltage actuation level (F022), it may occur before the braking resistor can
dissipate the motor regenerated energy. Table 8.2 on page 8-13 contains the adjustment ranges for the actuation
of the dynamic braking according to the model.
8-12 | CFW300
MOTOR CONTROL
Table 8.2: Dynamic braking actuation range

Input Voltage Input Voltage P0153 (factory default)
110 to 127 Vac 391 to 460 Vdc 395 Vdc
200 to 240 Vac 349 to 410 Vdc 365 Vdc
380 Vac 621 to 800 Vdc 800 Vdc
400 to 415 Vac 646 to 800 Vdc 800 Vdc
440 to 460 Vac 716 to 800 Vdc 800 Vdc
480 Vac 747 to 800 Vdc 800 Vdc
Figure 8.10 on page 8-13 shows an example of typical dynamic braking actuation, where the hypothetical wave
shapes of the voltage on the braking resistor and the DC link voltage can be observed. Thus, when the braking
IGBT connects the link to the external resistor, the DC link voltage drops below the value set by P153, keeping the
level below fault F022.
DC Link Voltage (Ud ) (P004)

F022 - overvoltage
P153 Dynamic braking
Rated Ud actuation
Time
Ud Ud
Braking resistor
voltage (DB) Time
Figure 8.10: Dynamic braking actuation curve

8
Steps to enable the dynamic braking:
With the inverter powered down, connect the braking resistor (Refer to the user’s manual of the Inverter).
Set P151 at the maximum value: (According to inverter model) to prevent the activation of the DC voltage
regulation before the dynamic braking.
DANGER!
! Be sure the inverter is OFF and disconnected before handling the electric connections and read
carefully the installation instructions of the user’s manual.
8.1.6 Skip Frequency
This inverter function prevents the motor from operating permanently at frequency values in which, for example,
the mechanical system goes into resonance (causing excessive vibration or noises).
P303 - Skip Frequency 1
P304 - Skip Frequency 2

CFW300 | 8-13
MOTOR CONTROL
Description:
These parameters represent the center of the frequency range avoided, according to Figure 8.11 on page 8-14.
P306 - Skip Band

Description:
The actuation of those parameters is done as presented in Figure 8.11 on page 8-14 below. The passage by the
skip frequency band (2 x P306) is done through acceleration/deceleration ramp. The function does not operate
correctly if two bands of “Skip Frequency” overlap.
2 x P306
Output
frequency
P304 2 x P306
P303
Reference
P303
P304
Figure 8.11: Actuation of the skip frequency
8
8.1.7 Fire Mode
The “Fire Mode” function is intended to make the frequency inverter continue to drive the motor even under adverse
conditions, inhibiting most faults generated by the frequency inverter. The “Fire Mode” is activated by driving a digital
input previously set to “Fire Mode” with logic level “0” at the input terminals. When the drive enters the “Fire Mode”,
the alarm “A211” will be generated on the HMI (keypad) and the status of the operation mode will be updated in
parameter P006.
8-14 | CFW300
MOTOR CONTROL
DANGER!
! FIRE MODE”FUNCTION - RISK OF DEATH!

Notice that the inverter is only one of the components of the system, and it is configurable for several
functions that must be pre-established in the project.
Therefore, the full operation of the “Fire Mode” function, with the required safety, depends on the
specification in the project, as it also requires the compatibility with all the other components of the
system and the installation environment.
Ventilation systems that operate in life safety applications must be approved by the Fire Department
and/or another competent local public authority.
The activation of the “Fire Mode” function disables essential protection functions for the safety of
the frequency inverter and of the system as a whole.
The non-interruption of the frequency inverter operation due to the improper activation of the “Fire
Mode” function is critical, as it may cause injuries or even death, and damages to the frequency
inverter, to the other components of the system and to the environment where it is installed.
The operation in the “Fire Mode” function may, under certain circumstances, result in fire, as the
protection devices will be disabled.
Only qualified personnel from safety engineer departments must evaluate and activate the
equipment Fire Mode function.
It is essential to follow the aforementioned instructions before using the frequency inverter in the
“Fire Mode” function.
Under no circumstance shall WEG take any liability for deaths, damages, compensations and/or
losses occurred due to the improper programming or operation of the frequency inverter in the “Fire
Mode” function.
IMPORTANT - RISK OF DEATH!

When activating the “Fire Mode” function, the user must be aware of the fact that the protection
functions of the frequency inverter will be disabled, which may result in damages:
1. to the inverter;
2. to the components connected to it;
3. to the environment where it is installed;
4. to the people present in the place. 8
Therefore, the operator who activates the “Fire Mode” function takes full liability for the resulting risks.
The operation of the inverter with the “Fire Mode” function programmed voids the warranty of the
product.
The operation in this condition is internally registered by the frequency inverter, and it may be validated
by an engineer and occupational safety professional duly qualified by the manufacturer.
✓
NOTE!
When activating the “Fire Mode” function, the user acknowledges that the protection functions of
the frequency inverter are disabled, which may result in damages to the frequency inverter, to the
components connected to it, to the environment in which it is installed and to the people present in
such environment. Therefore, the user takes full liability for the resulting risks. The operation of the
inverter with the “Fire Mode” function enabled voids the warranty of the product. The operation under
such condition is internally registered by the frequency inverter and must be validated by an engineer
and occupational safety professional duly qualified. If the user presses the key, the message will
disappear from the display (A211), but the operation mode will continue to be shown in parameter
P006. It is also possible to indicate this condition in a digital output (DOx) previously programmed for
“Fire Mode”. During the operation in “Fire Mode”, all the stop commands are ignored (even General
Enable). Some Faults (considered critical) that may damage the inverter will not be disabled, but they
can be infinitely reset automatically (define this condition in parameter P582): Overvoltage on the DC
Link (F022), Overcurrent/Short Circuit (F070).
CFW300 | 8-15
MOTOR CONTROL
P580 - Fire Mode Configuration

1 = Active
2 = Active / P134
3 = Reserved
4 = Active / General Disable
Properties: cfg
Description:
This parameter defines how the Fire Mode functionality will work in the frequency inverter.
Table 8.3: Options for the parameter P580

Option Description
0 Fire Mode function is inactive
Fire Mode function is active. When the DIx set to Fire Mode is opened, “A211” will be shown on the HMI and no changes will
1
be made to the speed reference or to the inverter control
Fire Mode function is active. When the DIx set to Fire Mode is opened, “A211” will be shown on the HMI and the Speed
2
Reference will be set automatically to maximum (P134) value. The motor will accelerate to this new reference
3 Reserved
Fire Mode function is active. When the DIx set to Fire Mode is opened, “A211” will be shown on the HMI and the pulses in the
4
output will be disabled. Motor will coast to stop
P582 - Fire Mode Auto-reset Adjustable
Range: 0 = Limited Default: 0

1 = Unlimited
Properties: cfg
8
Description:
This parameter defines how the auto-reset functionality will work in Fire Mode when a critical fault occur (DC Link
Overvoltage (F022) and Overcurrent/Short-circuit (F070)).
Table 8.4: Options for the parameter P582

Option Description
0 Limited. Auto-reset works as defined in P340 parameter
Unlimited. The auto-reset happens after 1s of a critical failure detection regardless of the
1
value set in P340
8.1.8 Control Configuration
P397 - Control Config
Range: 0 to F (hexa) Default: 11

Bit 0 = Slip Compens. Regen.
Bit 1 = Dead Time Comp.
Bit 2 = Is Stabilization
Bit 3 = P297 reduction in A050
Properties: cfg
Description:
The bits of parameter P397, as shown in Table 8.5 on page 8-17, enable a series of internal options to configure
the control of the induction motor, such as:
8-16 | CFW300
MOTOR CONTROL
Slip Compensation during the Regeneration (Bit 0 )

The regeneration is an operating mode of the inverter which occurs when the power flux goes from the motor to
the inverter. The bit 0 of P397 (set in 0) allows the slip compensation to be turned off in this situation. This option
is particularly useful when the compensation during the motor deceleration is necessary.
Dead Time Compensation (Bit 1)

The dead time is a time interval introduced in the PWM necessary for the commutation of the power inverter
bridge. On the other hand, the dead time generates distortions on the voltage applied to the motor, which can
cause torque reduction at low speeds and current oscillation in motors above 5 HP running with no load. Thus,
the dead time compensation measures the voltage pulse width in the output and compensates this distortion
introduced by the dead time. This parameter must be kept always in 1 (On). Only in special maintenance cases
the value 0 (Off) can be used.
Output Current Stabilization (Bit 2)

High-performance motors with power above 5 HP are marginally stable when driven by frequency inverters and
at operation with no load. Therefore, in this situation a resonance may occur in the output current which may
reach the overcurrent level F070. Bit 2 of P397 (set to 1) activates an algorithm for regulation of the output current
in closed loop which neutralizes the oscillations of resonant output current.
Reduction of P297 at high temperature (Bit 3)

Bit 3 of P397 controls the action to reduce the switching frequency together with the overtemperature protection
according to Table 11.2 on page 11-4. If the temperature exceeds the value of A050, the switching frequency is
reduced proportionally down to its minimum when the temperature reaches the level of F051.
✓
NOTE!
Both the function related to P219 and the function controlled by P397 (bit 3) act by reducing the
switching frequency. As the function related to P219 is intended to improve the reading of the inverter
current, that function has priority of action over the function controlled by P397 (bit 3).
WARNING! 8
! The default setting of P397 meets most application needs of the inverter. Therefore, avoid modifying
its content without knowing the related consequences. If you are not sure, contact WEG Technical
Assistance before changing P397.
Table 8.5: Options available to configure the control (P397)

Bit 3 Bit 2 Bit 1 Bit 0
P397 Reduction of P297 in Output Current Dead Time Slip Compensation
A050 Stabilization Compensation During Regeneration
0000h Disabled Disabled Disabled Disabled
0001h Disabled Disabled Disabled Enabled
0002h Disabled Disabled Enabled Disabled
0003h Disabled Disabled Enabled Enabled
0004h Disabled Enabled Disabled Disabled
0005h Disabled Enabled Disabled Enabled
0006h Disabled Enabled Enabled Disabled
0007h Disabled Enabled Enabled Enabled
0008h Enabled Disabled Disabled Disabled
0009h Enabled Disabled Disabled Enabled
000Ah Enabled Disabled Enabled Disabled
000Bh Enabled Disabled Enabled Enabled
000Ch Enabled Enabled Disabled Disabled
000Dh Enabled Enabled Disabled Enabled
000Eh Enabled Enabled Enabled Disabled
000Fh Enabled Enabled Enabled Enabled
CFW300 | 8-17
MOTOR CONTROL
8.2 V/F
This is the classical control method for three-phase induction motors, based on a curve that relates output frequency
and voltage. The inverter works as a variable frequency and voltage source, generating a combination of voltage
and frequency according to the configured curve. It is possible to adjust this curve for standard 50 Hz, 60 Hz or
special motors.
According to the block diagram of Figure 8.12 on page 8-19, the frequency reference f* is limited by P133 and
P134 and applied to the input of “V/f Curve” block, where the output voltage amplitude and frequency imposed to
the motor are obtained. For further details on the frequency reference, refer to Section 7.2 SPEED REFERENCE
on page 7-6.
By monitoring the total and active output current, and the DC link voltage, compensators and regulators are
implanted so as to help in the protection and performance of the V/f control. The operation and parameterization
of those blocks are detailed in Section 8.1 COMMON FUNCTIONS on page 8-1.
The advantage of the V/f control is its simplicity and the need of few settings. The start-up is quick and simple
and the factory default, in general, requires little or no modification. In cases whose objective is to reduce losses
on the motor and inverter, the “Quadratic V/f” may be used, where the flow in the motor air-gap is proportional to
the output frequency up to the field weakening point (also defined by P142 and P145). Thus, the result is a torque
capacity as a quadratic function of the frequency. The great advantage of such control is the capacity to save
energy when driving loads with variable resistant torque, due to the reduction of motor losses (especially losses in
the air-gar, magnetic losses).
The V/f or scalar control is recommended for the following cases:
Drive of several motors with the same inverter (multi-motor drive).
Energy saving in the drive of loads with quadratic torque/frequency relationship.
Motor rated current lower than 1/3 of the inverter rated current.
For test purposes, the inverter is turned on without motor or with a small motor with no load.
8 Applications where the load connected to the inverter is not a three-phase induction motor.
Applications that aim at reducing losses on the motor and inverter (Quadratic V/f).
8-18 | CFW300
Power Supply
P202 = 0 (control V/f)

or
DC Link Regulation P202 = 1 (quadratic V/f)
Ud P004
Ud Curve V/f
P202 = 0 (V/f)
P151 P142
P143
P151 P137 Direction of rotation
P136
P146 P145 f
P202 = 1 + mixr PWM

m P007 PWM
P100-P104 (Quadratic V/f)
P134 + Space Vector
f* P142 + fo P002
modulation
P133 + fslip
P136
P145 f Angle,
sextant Ish
Zero m Io
Figure 8.12: Block diagram of V/f scale control

MI
Calculation of Ia Ish 3ϕ
P135 Io P138
Ia
Io P003 Iv ,Iw
Calculation of Io
CFW300 | 8-19
MOTOR CONTROL
8
MOTOR CONTROL
The V/f curve is completely adjustable in four different points as according to Figure 8.13 on page 8-20, although
the factory default set a curve pre-adjusted for motors 50 Hz or 60 Hz, as options for P204. This format, point P0
defines the amplitude applied at 0 Hz, while P2 defines the rated amplitude and frequency and beginning of field
weakening. Intermediate points P1 allow the setting of the curve for a non-linear relationship between torque and
frequency, for instance, in fans where the load torque is quadratic in relation to the frequency. The field weakening
region is determined between P2 and P3 , where the amplitude is maintained in 100 %.
Output
voltage (%)
P142
P2 P3
P143
P1
P136
P0
P146 P145 P134 Output
frequency (Hz)
Figure 8.13: Curve V/f
The factory default setting of the frequency inverter defines a linear relation of the torque with the frequency by
means of three points (P0 , P1 and P2 ).
The points P0 [P136, 0 Hz], P1 [P143, P146], P2 [P142, P145] and P3 [100 %, P134] can be set so that the voltage
and frequency relation imposed to the output approximates the ideal curve for the load. Therefore, for loads in
which the torque behavior is quadratic in relation to the frequency, such as in centrifugal pumps and fans, the
points of the curve can be set or the Quadratic V/f control mode can be used so as to save energy. This Quadratic
8 V/f curve is presented in Figure 8.14 on page 8-20.
Output
voltage (%)
P142
P136
P145 P134 Output

frequency (Hz)
Figure 8.14: Quadratic V/f Curve
✓
NOTE!
In frequencies below 0.1 Hz, the output PWM pulses are cut, except when the inverter is in DC Braking
mode.
8-20 | CFW300
MOTOR CONTROL
✓
NOTE!
Read chapter 3 Installation and Connection of the frequency inverter user’s manual before installing,
energizing or operating the inverter.
Sequence for installation, verification, power up and start-up:
1. Install the inverter: according to chapter 3 Installation and Connection of the user’s manual, making all the
power and control connections.
2. Prepare and power up the inverter according to Section 3.2 Electrical Installation of the user’s manual of the
frequency inverter.
3. Load the factory default with P204 = 5 (60 Hz) or P204 = 6 (50 Hz), according to the input rated frequency
(power supply) of the inverter used.
4. Set the value of P296 according to the rated supply voltage (only for the 400 V Line).
5. In order to set a V/f curve different from the default, set the V/f curve using parameters P136 to P146.
6. Setting of specific parameters and functions for the application: program the digital and analog inputs and
outputs, HMI keys, etc., according to the application requirements.
P136 - Manual Torque Boost
Range: 0.0 to 30.0 % Default: According to the

Inverter Model
Properties: V/f
Description:
It actuates at low speeds, that is, in the range 0 to P146 (V/f) or 0 to P145 (Quadratic V/f), increasing the inverter 8
output voltage so as to compensate the voltage drop in the motor stator resistance in order to keep the torque
constant.
The optimum setting is the smallest value of P136 which allows the motor satisfactory start. A value greater than
necessary will excessively increase the motor current at low speeds, which may lead the inverter to a fault condition
(F051 or F070) or alarm condition (A046 or A050), as well as motor overheating. Figure 8.15 on page 8-21 and
Figure 8.16 on page 8-22 show the actuation regions of the Torque Boost for the V/f and Quadratic V/f mode,
respectively.
Output
voltage (%)
P142
P2 P3
P143
P1
P136
P0
frequency (Hz)
Figure 8.15: Torque boost region for quadratic V/f control mode
CFW300 | 8-21
MOTOR CONTROL
Output
voltage (%)
P142
P136
P145 P134 Output

frequency (Hz)
Figure 8.16: Torque boost region for quadratic V/f control mode
P137 - Automatic Torque Boost
Range: 0.0 to 30.0 % Default: 0.0 %

Properties: V/f
Description:
The automatic torque boost compensates the voltage drop in the stator resistance because of active current.
Look at Figure 8.12 on page 8-19, where variable IxR corresponds to the automatic torque boost action on the
modulation index defined by V/f curve.
P137 actuates similarly to P136, but the value set is applied proportionally to the output active current in relation to
the maximum current (2 x P295).
8 The setting criteria of P137 are the same as those of P136, that is, set the value as low as possible for the motor
start and operation at low frequencies, because values above those increase the losses, heating and overload of
the motor and inverter.
The block diagram of Figure 8.17 on page 8-22 shows the automatic compensation action IxR responsible for the
increment of the voltage in the ramp output according to the increase of the active current.
P007
IxR Voltage
Frequency reference applied on
P136
the motor
IxR
Output automatic
active current P137
P139
Figure 8.17: Block diagram of the automatic torque boost
P138 - Slip Compensation
Range: -10.0 to 10.0 % Default: 0.0 %

Properties: V/f
Description:
Parameter P138 is used in the motor slip compensation function, when set for positive values. In this case, it
8-22 | CFW300
MOTOR CONTROL
compensates the speed drop due to the application of load on the shaft and, consequently, the slip. Thus, it
increments the output frequency (Δf) considering the increase of the motor active current, as shown in Figure 8.18
on page 8-23. In Figure 8.12 on page 8-19 this compensation is represented in the variable fSlip .
The setting in P138 allows regulating with good accuracy the slip compensation by moving the operation point on
the V/f curve, as shown in Figure 8.18 on page 8-23. Once P138 is set, the inverter is able to keep the frequency
constant even with load variations.
Negative values are used in special applications where you wish to reduce the output frequency considering the
increase of the motor current.
Eg.: load distribution in motors driven in parallel.
Output
voltage (%)
P142
P143
P136 ∆f

frequency (Hz)
Figure 8.18: Slip compensation in an operation point of the standar V/f curve
P142 - Maximum Output Voltage

8
P143 - Intermediate Output Voltage
Range: 0.0 to 100.0 % Default: 100.0 %

Description:
These parameters allow adjusting the inverter V/f curve together with its orderly pairs P145 and P146.
P145 - Field Weakening Speed
P146 - Intermediate Frequency
Range: 0.0 to 400.0 Hz Default: 60.0 (50.0) Hz

Description:
These parameters allow adjusting the inverter V/f curve together with its orderly pairs P142 and P143.
The V/f curve can be adjusted in applications where the motor rated voltage is smaller than the power supply
voltage, for example, a power supply of 220 V with motor of 200 V.
The adjustment of the V/f curve is necessary when the motor has a frequency different from 50 Hz or 60 Hz, or when
a quadratic approximation is desired for energy saving in centrifugal pumps and fans, or in special applications:
when a transformer is used between the inverter and the motor or the inverter is used as a power supply.
CFW300 | 8-23
MOTOR CONTROL
8.2.1 Energy Saver (EOC)
The efficiency of a machine is defined as being the ratio between the output mechanical power and the input
electrical power. Remember that the mechanical power is the product between torque and rotor speed, and that
the input electric power is the sum of the output mechanical power and the motor losses.
In the case of the three-phase induction motor, the optimized efficiency is achieved with ¾ of the rated load. In the
region below this point, the Energy Saving function has its best performance.
The Energy Saving function acts directly on the voltage applied on the inverter output; thus, the flux relationship
delivered to the motor is changed so as to reduce the motor losses and enhance the efficiency, consequently
reducing consumption and noise.
Output Output
voltage (%) voltage (%)
P142 P142
P589
P589
P590 P145 P134 Output P590 P145 P134 Output

(a) Voltage in V/f frequency (Hz) (b) Voltage in quadratic V/f frequency (Hz)
Figure 8.19: (a) and (b) Example of voltage behavior in V/f and quadratic V/f
The function will be active when the motor load is below the maximum value (P588) and the frequency is above
the minimum value (P590). In addition, in order to prevent the stalling of the motor, the applied voltage is limited to
a minimum acceptable value (P589). The parameter group presented in the sequence defines the characteristics
8 necessary for the energy saving function.
✓
NOTE!
The use of the energy saving function is recommended in quadratic torque applications (blowers,
fans, pumps and compressors).
P011 - Power Factor
Properties: ro
Description:
It indicates the power factor, that is, the relationship between the real power and the total power absorbed by the
motor.
P407 - Motor Rated Power Factor
Range: 0.50 to 0.99 Default: According to the

Inverter Model
Properties: cfg, VVW
Description:
Setting of the motor rated power factor.
In order to obtain the proper operation of the energy saving function, the motor power factor must be correctly set,
8-24 | CFW300
MOTOR CONTROL
according to the information on the motor nameplate.

Note: With the motor nameplate data and for applications with constant torque, the motor optimum efficiency is
normally obtained with the energy saving function active. In some cases, the output current may increase, and then
it is necessary to gradually reduce the value of this parameter to the point in which the current value remains equal
to or below the current value obtained with the function disabled.
For information regarding the actuation of P407 in the VVW control mode, refer to Section 8.3 VVW on page 8-26.
P588 - EOC Maximum Torque
Range: 0 to 85 % Default: 0%
Properties: cfg
Description:
This parameter defines the torque value to activate the operation of the energy saving function.
Setting this parameter to 0 % disables the function.
It is recommended to set this parameter to 60 %, but it has to be set according the application requirements.
P589 - EOC Minimum Voltage
Range: 40 to 80 % Default: 40 %
Properties: cfg
Description:
This parameter defines the minimum voltage value that will be applied to the motor when the energy saving function
is active. This minimum value is relative to the voltage imposed by the V/f curve for a certain speed.
P590 - EOC Minimum Frequency 8

Properties: cfg
Description:
This parameter defines the minimum speed value at which the energy saving function will remain active.
The hysteresis for the minimum speed level is of 2 Hz.
P591 - EOC Hysteresis
Properties: cfg
Description:
Hysteresis used to activate and deactivate the energy saving function.
If the function is active and the output current oscillates, it is necessary to increase the hysteresis value.
✓
NOTE!
It is not possible to set those parameters, while the motor is spinning.
CFW300 | 8-25
MOTOR CONTROL
8.3 VVW
The VVW vector control mode (Voltage Vector WEG) uses a control method with a much higher performance than
the V/f control because of the load torque estimation and of the control of the magnetic flux in the air gap, as per
scheme of Figure 8.20 on page 8-27. In this control strategy, losses, efficiency, rated slip and power factor of the
motor are considered in order to improve the control performance.
The main advantage compared to the V/f control is the best frequency regulation with greater torque capacity
at low speeds (frequencies below 5 Hz), allowing a relevant improvement in the drive performance in permanent
duty. Besides, the VVW control has a quick and simple setting and it is suitable for most medium-performance
applications in the control of three-phase induction motor.
By just measuring the output current, the VVW control instantly obtains the motor torque and slip. Thus, the VVW
actuates in the output voltage compensation and slip compensation. Therefore, the VVW controller action replaces
the classical V/f functions in P137 and P138, but with a calculation model much more sophisticated and accurate,
meeting several load conditions or operation points of the application.
In order to achieve a good frequency regulation in permanent duty with a good operation of the VVW control, the
parameter setting in the range P399 to P407, and the stator resistance in P409 are essential for the good operation
of the VVW control. These parameters can be easily obtained on the motor nameplate.
8-26 | CFW300
Power supply
P202 = 5 (VVW Control)
DC Link Regulation Ud P004
P400, P403, P401, P407,

Ud
P409, P178
Ud
Flux control m* Output voltage

P151 compensation Direction of rotation
Ia Io m P007 PWM PWM

P100-P104
P134 Space Vector
f* fr fo P002 fo
modulation
P133
fslip
P295 Angle,
Zero Ish
Figure 8.20: VVW control flow

P140 sextant Io
Filter
m MI
Current limitation Calculation of Ia Ish 3ϕ
controller
P135 fo
P403 Calculation of fslip
Ia
P295
TL /TR , SR
404, P399, fo
P401,P409, Ia
Torque Iv ,Iw
P402, P403 Io Calculation of Io
estimation
Ud m
Io P003
CFW300 | 8-27
MOTOR CONTROL
8
MOTOR CONTROL
Opposite to the V/f scalar control, the VVW control requires a series of data from the motor nameplate and a self-
tuning for its proper operation. Besides, it is recommended that the driven motor match the inverter, that is, the
motor and inverter power be as close as possible.
Below are described the parameters to configure the VVW vector control setting. This data is easily obtained on
WEG standard motor nameplates, however in older motors or motors made by other manufacturers, the data may
not be readily available.
In those cases, it is recommended first contact the motor manufacturer, measure or calculate the desired parameter.
As a last resort, the user always can make a relationship with Table 8.6 on page 8-29 and use the equivalent or
approximate WEG standard motor parameter.
✓
NOTE!
The correct setting of the parameters directly contributes to the VVW control performance.
8-28 | CFW300
MOTOR CONTROL
Table 8.6: Characteristics of IV pole WEG standard motors (indicative values)

Power Voltage Current Frequency Speed Efficiency Stator
Frame Power
[P400] [P401] [P403] [P402] [P399] Resistance [P409]
(HP) (kW) Size Factor
(V) (A) (Hz) (rpm) (%) (Ω)
0.16 0.12 63 0.85 1720 56.0 0.66 21.77
0.25 0.18 63 1.12 1720 64.0 0.66 14.87
0.33 0.25 63 1.42 1720 67.0 0.69 10.63
0.5 0.37 71 2.07 1720 68.0 0.69 7.37
0.75 0.55 71 2.90 1720 71.0 0.70 3.97
1.00 0.75 80 220 3.08 60 1730 78.0 0.82 4.13
1.50 1.10 80 4.78 1700 72.7 0.83 2.78
2.00 1.50 90S 6.47 1720 80.0 0.76 1.55
3.00 2.20 90L 8.57 1710 79.3 0.85 0.99
4.00 3.00 100L 11.6 1730 82.7 0.82 0.65
5.00 3.70 100L 13.8 1730 84.6 0.83 0.49
0.16 0.12 63 0.49 1720 56.0 0.66 65.30
0.25 0.18 63 0.65 1720 64.0 0.66 44.60
0.33 0.25 63 0.82 1720 67.0 0.69 31.90
0.5 0.37 71 1.20 1720 68.0 0.69 22.10
0.75 0.55 71 1.67 1720 71.0 0.70 11.90
1.00 0.75 80 1.78 1730 78.0 0.82 12.40
1.50 1.10 80 2.76 1700 72.7 0.83 8.35
380 60
2.00 1.50 90S 3.74 1720 80.0 0.76 4.65
3.00 2.20 90L 4.95 1710 79.3 0.85 2.97
4.00 3.00 100L 6.70 1730 82.7 0.82 1.96
5.00 3.70 100L 7.97 1730 84.6 0.83 1.47
6.00 4.50 112M 9.41 1730 84.2 0.86 1.15
7.50 5.50 112M 11.49 1740 88.5 0.82 0.82
10.0 7.50 132S 15.18 1760 89.0 0.84 0.68
0.16 0.12 63 0.73 1375 57.0 0.72 30.62
0.25 0.18 63 1.05 1360 58.0 0.74 20.31
0.33 0.25 71 1.4 1310 59.0 0.76 14.32
0.50 0.37 71 1.97 1320 62.0 0.76 7.27
0.75 0.55 80 2.48 1410 68.0 0.82 5.78
1.00 0.75 80 230 3.26 50 1395 72.0 0.81 4.28
1.50 1.10 90S 4.54 1420 77.0 0.79 2.58
8
2.00 1.50 90L 5.81 1410 79.0 0.82 1.69
3.00 2.20 100L 8.26 1410 81.5 0.82 0.98
4.00 3.00 100L 11.3 1400 82.6 0.81 0.58
5.00 3.70 112M 14.2 1440 85.0 0.83 0.43
0.16 0.12 63 0.42 1375 57.0 0.72 91.85
0.25 0.18 63 0.60 1360 58.0 0.74 60.94
0.33 0.25 71 0.80 1310 59.0 0.76 42.96
0.50 0.37 71 1.13 1320 62.0 0.76 21.81
0.75 0.55 80 1.42 1410 68.0 0.82 17.33
1.00 0.75 80 1.86 1395 72.0 0.81 12.85
1.50 1.10 90S 400 2.61 50 1420 77.0 0.79 7.73
2.00 1.50 90L 3.34 1410 79.0 0.82 5.06
3.00 2.20 100L 4.75 1410 81.5 0.82 2.95
4.00 3.00 100L 6.47 1400 82.6 0.81 1.75
5.00 3.70 112M 8.18 1440 85.0 0.83 1.29
7.50 5.50 132S 11.0 1450 86.0 0.84 0.76
10.0 7.50 132M 14.8 1455 87.0 0.84 0.61
✓
NOTE!
Read chapter 3 Installation and Connection of the frequency inverter user’s manual before installing,
energizing or operating the inverter.
Sequence for installation, verification, power up and start-up:
1. Install the inverter: according to chapter 3 Installation and Connection of the user’s manual, making all the
power and control connections.
CFW300 | 8-29
MOTOR CONTROL
2. Prepare and power up the inverter: according to Section 3.2 Electrical Installation of the user’s manual.
3. Load the correct factory default in P204: based on the motor rated frequency (set P204 = 5 for 60 Hz
motors and P204 = 6 for 50 Hz motors.
4. Setting of specific parameters and functions for the application: program the digital and analog inputs
and outputs, HMI keys, etc., according to the application requirements.
5. Activation of the VVW control: set P202 = 5 and parameters P399, P400, P401, P402, P403, P404 and
P407 according to the motor nameplate. Also set the value of P409. If some of those data are not available,
enter the approximate value by calculation or by similarity with WEG standard motor, see the Table 8.6 on
page 8-29.
6. Self-Tuning of the VVW control: the self-tuning is activated by setting P408 = 1. In this process, the inverter
applies DC to the motor to measure the stator resistance, while the HMI bar graph shows the progress of the
self-tuning. The self-tuning process can be interrupted at any time by pressing the key.
7. End of the Self-Tuning: at end of the self-tuning, the HMI returns to the browsing menu, the bar displays
the parameter programmed by P207 again and the stator resistance measured is stored in P409. On the
other hand, if the self-tuning fails, the inverter will indicate a fault. The most common fault in this case is F033,
which indicates error in the estimated stator resistance. Refer to Chapter 10 FAULTS AND ALARMS on page
10-1.
For better visualization of the start-up in the VVW mode, check Table 8.7 on page 8-31.
8-30 | CFW300
MOTOR CONTROL
Table 8.7: Start-up of the VVW mode
Seq Indication on the Display / Action Seq Indication on the Display / Action
Initialization mode
Press this key to enter the first level of the setting Press the or keys until selecting parameter P296
mode
If necessary, change the content of “P296 - Line Rated Press the key to change the content of “P202 -
Voltage” (only for 400 V line) Control Type” to P202 = 5 (VVW)
Press the key until selecting parameter P202 Use the key
Press the key to save the change of P202 If necessary, change the content of “P399 - Motor
Use the key until selecting parameter P399 Rated Efficiency” according to data on the nameplate
Press the key for the next parameter
If necessary, change the content of “P400 - Motor If necessary, change the content of “P401 - Motor
Rated Voltage” Rated Current”
Press the key for the next parameter Press the key for the next parameter
Rated Speed” Rated Frequency”
8
Rated Output” Rated Power Factor”
If necessary to make the self-tuning, change the value of During the self-tuning, the HMI will show “Auto” and the
P408 to “1” bar will indicate the operation progress
When the self-tuning is completed, it will return to the If necessary, change the content of “P409 - Stator
Initialization Mode Resistance”
P140 - Slip Com. Filter

Properties: VVW
Description:
Time constant of the filter for slip compensation in the output frequency. You must consider a filter response time
equal to three times the time constant set in P140.
CFW300 | 8-31
MOTOR CONTROL
P178 - Rated Flux
Range: 50.0 to 150.0 % Default: 100.0 %

Properties: VVW
Description:
It defines the desired flux in the motor air gap in percentage (%) of the rated flux. In general, it is not necessary
to modify the value of P178 of the standard value of 100.0 %. However, some specific situations may use values
slightly above to increase the torque, or below to reduce the energy consumption.
P399 - Motor Rated Efficiency
Range: 50.0 to 99.9 % Default: According to the

Inverter Model
Description:
This parameter is important for the precise operation of the VVW control. A misconfiguration will cause incorrect
calculation of the slip compensation, reducing the performance of the speed control.
P400 - Motor Rated Voltage
Range: 0 to 480 V Default: 220 V

Description:
Set according to the data on the motor nameplate and the wire connection on the motor terminal box. Default
8 values are shown in the Table 8.8 on page 8-32. This value cannot be above the rated voltage value set in P296
(power supply rated voltage).
Table 8.8: Default setting of P400 according to the identified inverter model
P296 P145 (Hz) P400 (V)
0 Reserved Reserved
50.0 230
1
60.0 220
50.0 230
2
60.0 220
3 Reserved Reserved
4 50/60 380
5 50/60 415
6 50/60 440
7 50/60 480
For further information on model identification, refer to Table 6.1 on page 6-2 of Chapter 6 FREQUENCY INVERTER
IDENTIFICATION on page 6-1.
P401 - Motor Rated Current

Description:
It defines the rated motor current. Parameter P401 must be set according to the information on the motor
nameplate, taking into account the motor voltage.
8-32 | CFW300
MOTOR CONTROL
✓
NOTE!
It is not recommended setting the motor rated current greater than inverter rated current (P295).
P402 - Motor Rated Speed
Range: 0 to 24000 rpm Default: 1720 rpm

Description:
It defines the rated motor speed. Parameter P402 must be set according to the information on the motor nameplate.
The setting of parameter P402 via HMI for values above 9999 rpm is performed from 10.00 to 30.00 rpm (x 1000).
P403 - Motor Rated Frequency
Range: 0 to 400 Hz Default: 60 Hz

Description:
It defines the rated motor frequency. Parameter P403 must be set according to the information on the motor
nameplate.
P404 - Motor Rated Power
Range: 0 = 0.16 HP (0.12 kW) Default: 2

1 = 0.25 HP (0.18 kW) 8
2 = 0.33 HP (0.25 kW)
3 = 0.50 HP (0.37 kW)
4 = 0.75 HP (0.55 kW)
5 = 1.00 HP (0.75 kW)
6 = 1.50 HP (1.10 kW)
7 = 2.00 HP (1.50 kW)
8 = 3.00 HP (2.20 kW)
9 = 4.00 HP (3.00 kW)
10 = 5.00 HP (3.70 kW)
11 = 5.50 HP (4.00 kW)
12 = 6.00 HP (4.50 kW)
13 = 7.50 HP (5.50 kW)
14 = 10.00 HP (7.50 kW)
Description:
It defines the rated motor power. Parameter P404 must be set according to the information on the motor
nameplate.
P408 - Run Self-Tuning
Range: 0 = No Default: 0
1 = Yes
CFW300 | 8-33
MOTOR CONTROL
Description:
Parameter P408 in 1 activates the self-tuning of the VVW mode, where the motor stator resistance is measured.
The self-tuning can only be activated via HMI, and it can be interrupted at any time with the key.
During the self-tuning, the bar graph shows the progress of the operation and the motor remains still, because a
DC signal is sent to measure the stator resistance.
If the estimated value of the motor stator resistance is too high for the inverter used (for example: motor not
connected or motor too small for the inverter) the inverter indicates fault F033.
At the end of the self-tuning process, the measured motor stator resistance is saved in P409.
✓
NOTE!
The self-tuning will not run if the inverter is in Alarm or Fault.
P409 - Stator Resistance
Range: 0.01 to 99.99 Default: According to the

Inverter Model
Description:
Motor phase stator resistance in ohms (Ω). This value can be estimated by Self-Tuning.
If the value adjusted in P409 is too high or too low for the inverter used, the inverter indicates fault F033. In order
to exit this condition, just perform a reset by using the key, in this case, P409 will be loaded with the factory
default value.
8-34 | CFW300
I/O
9 I/O
This chapter contains the parameters for setting the inverter inputs and outputs. This setting depends on the
accessory connected to the product.
✓
NOTE!
The inverter HMI only displays the parameters related to the resources available in the accessory
connected to the product.
9.1 ANALOG INPUTS
For example, the use of an external frequency reference is possible via the analogue inputs. The details for this
configuration are described in the following parameters.
Each analog input of the inverter is defined by the steps of calculation of Signal, Offset, Gain, Filter, Function and
Value AIx, as shown in Figure 9.1 on page 9-1.
Input
AI1 AI1 - P018
AI2(*) AI2 - P019
Filter
Signal Gain Function
AI1 - P233 AI1 - P232 AI1 - P231
AI2 - P238 AI2 - P237 AI2 - P236
AI1 - P235
Offset AI2 - P240 Value AIx
AI1 - P234 (internal)
AI2 - P239
(*) Control terminal available on the IO´s expansion accessory.

Figure 9.1: Block diagram of the analog inputs - (AIx)
P018 - AI1 Value

9
P019 - AI2 Value
Range: -100.0 to 100.0 % Default:
Properties: ro
Description:
Those read-only parameters indicate the value of the analog inputs AI1 and AI2 in percentage of the full scale. The
indicated values are those obtained after the offset action and multiplication by the gain. Check the description of
parameters P230 to P245.
P230 - Dead Zone (AIs and FI1 )

1 = Active
Properties: cfg
Description:
This parameter acts for the analog inputs (AIx) or for the frequency input (FI) programmed as frequency reference,
and it defines if the dead zone in those inputs is Active (1) or Inactive (0).
CFW300 | 9-1
I/O
If the parameter is configured as Inactive (P230 = 0), the signal in the analog inputs will actuate on the frequency
reference from the minimum point (0 V / 0 mA / 4 mA or 10 V / 20 mA), and it will be directly related to the minimum
frequency set in P133. Check Figure 9.2 on page 9-2.
If the parameter is set as Active (P230 = 1), the signal in the analog inputs will have a dead zone, where the frequency
reference remains at the Minimum frequency value (P133), even with the variation of the input signal. Check Figure
9.2 on page 9-2.
Reference Reference
P134 P134
P133 P133
Signal AIx Signal AIx

0..........................................10 V 0...........................................10 V
0..........................................20 mA 0...........................................20 mA
4 mA...................................20 mA 4 mA....................................20 mA
10 V.......................................0 10 V.......................................0
20 mA...................................0 20 mA....................................0
20 mA...................................4 mA 20 mA....................................4 mA
(a) Inactive (a) Active
Figure 9.2: (a) and (b) Actuation of the analog inputs with dead zone
P231 - AI1 Signal Function
9 P236 - AI2 Signal Function
Range: 0 = Speed Ref. Default: 0

1 to 3 = Not Used
4 = PTC
5 to 6 = Not Used
7 = PLC Use
Properties: cfg
Description:
These parameters define the analog inputs functions.
When the 0 option (Speed Reference) is selected, the analog input can provide the frequency reference for the
motor, subject to the specified limits (P133 and P134) and to the action of the ramps (P100 to P103). However, it
9-2 | CFW300
I/O
is also necessary to configure parameters P221 and/or P222 by selecting the analog input. For further details, see
the description of those parameters in Chapter 7 COMMAND AND REFERENCES on page 7-1.
Option 4 (PTC) configures the input to monitor the motor temperature. For further details on this function, refer to
Section 10.3 PROTECTIONS on page 10-3.
Option 7 (PLC Use), as well as options 8 to 15, configures the input to be used by the programming done in the
memory area reserved for the SoftPLC function. For further details, refer to the help menu of the WPS software.
Options 16 and 17 configure the input for the use of the PID Controller application (P903 = 1). For further details,
see Chapter 14 APPLICATIONS on page 14-1.
P232 - AI1 Input Gain
P237 - AI2 Input Gain
Range: 0.000 to 9.999 Default: 1.000

Description:
The parameters define the gains of the analog inputs.
Each analog input of the inverter is defined by the steps of calculation of Signal, Offset, Gain, Filter, Function and
Value AIx, as shown in Figure 9.1 on page 9-1.
P233 - AI1 Input Signal
P238 - AI2 Input Signal
Range: 0 = 0 to 10 V / 20 mA Default: 0
1 = 4 to 20 mA
2 = 10 V / 20 mA to 0
3 = 20 to 4 mA
Description:
9
These parameters configure the signal type (if current or voltage) that will be read in each analog input, as well as
its variation range. In options 2 and 3 of the parameters, the reference is inverse, that is, the maximum frequency
is obtained with the minimum reference.
Pay attention to the connections of the analog input with voltage or current signal according to the inverter used.
For analog inputs on expansion accessories, refer to the installation, configuration, and operation guide of the I/O
expansion accessory used.
CFW300 | 9-3
I/O
Table 9.1: Alx configuration and equation

Signal P233 or P238 Equation AIx(%)
( )
AIx(V)
0 to 10 V 0 AIx(%) = x (100.0 %) + offset x gain
10 V
( )
AIx(mA)
0 to 20 mA 0 AIx(%) = x (100.0 %) + offset x gain
20 mA
( )
AIx(mA) - 4 mA
4 to 20 mA 1 AIx(%) = x (100.0 %) + offset x gain
16 mA
( )
AIx(V)
10 to 0 V 2 AIx(%) = 100 % - x (100.0 %) + offset x gain
10 V
( )
AIx(mA)
20 to 0 mA 2 AIx(%) = 100 % - x (100.0 %) + offset x gain
20 mA
( )
AIx(mA) - 4 mA
20 to 4 mA 3 AIx(%) = 100 % - x (100.0 %) + offset x gain
16 mA
For example: AIx = 5 V, offset = -70.0 %, gain = 1.000, with signal of 0 to 10 V, that is, AIxini = 0 and AIxFE = 10.
( )
5
AIx(%) = x (100.0 %) + (-70 %) x 1.000 = -20.0 %
10
Another example: AIx = 12 mA, offset = -80.0 %, gain = 1.000, with signal of 4 to 20 mA, that is, AIxini = 4 and
AIxFE = 16.
( )
12 - 4
AIx(%) = x (100.0 %) + (-80 %) x 1.000 = -30.0 %
16
9 AIx = -30.0 % means that the motor will spin forward with a reference in module equal to 30.0 % of P134, if the
signal AIx function is “Frequency Reference”.
In the case of filter parameters (P235), the value set corresponds to the time constant used to filter the input signal
read. Therefore, the filter response time is around three times the value of this time constant.
P234 - AI1 Input Offset
P239 - AI2 Input Offset
Range: -100.0 to 100.0 % Default: 0.0 %

Description:
The parameters define the offsets of the analog inputs.
Each analog input of the inverter is defined by the steps of calculation of signal, offset, gain, filter, function and value
AIx, as shown in Figure 9.1 on page 9-1.
P235 - AI1 Input Filter
9-4 | CFW300
I/O
P240 - AI2 Input Filter

Description:
These parameters define the times of the analog input filters.
9.2 EXTERNAL TEMP. SENSOR INPUT
Depending on the inverter (see the user’s manual), there is an exclusive input to connecting an external temperature
sensor, in some cases it is an I/O of the inverter itself, in others, the sensor connection is via an expansion module.
The parameter to read the temperature is described below.
P375 - External Sensor Temp.
Range: 0 to 200 ºC Default:
Properties: ro
Description:
This read-only parameter indicates the temperature value obtained from an external temperature sensor.
✓
NOTE!
When the external sensor is NTC, which is disconnected from the accessory, the frequency inverter
will display 999 °C (1830 °F) in parameter P375. If the connection pins of the NTC (accessory
connector) are shorted, the value indicated on P375 will be 0 °C (32 °F).
In case the external temperature/humidity sensor, when disconnected, will present a measurement
of 0 °C (32 °F) in parameter P375.
9.3 SIGNAL POTENTIOMETER INPUT

9
The IOP accessory provides the potentiometer signal value for the frequency inverter. The steps to calculate this
value are indicated in the block diagram of the Figure 9.3 on page 9-5.
Value
P020
Filter
Input Gain Function
IOP P242 P245 P241
Offset Value AIP

P244 (internal)
Figure 9.3: Block diagram of the AIP potentiometer signal input
The AIP value can be used as a frequency reference or accessed by the WPS software. The details for the possible
configurations are described in the following parameters.
CFW300 | 9-5
I/O
P020 - Potentiometer Signal Value
Properties: ro
Description:
This read-only parameter indicates the analog signal value of the AIP potentiometer as a percentage of the full scale.
The indicated values are obtained after the offset action and the multiplication by the gain.
P241 - Potentiometer Signal Function

1 to 6 = Not Used
7 = SoftPLC
16 to 17 = Not Used
Properties: cfg
Description:
This parameter defines the function of the potentiometer signal input.
P242 - Potentiometer Signal Gain
9 Range: 0.000 to 9.999 Default: 1.000

Description:
This parameter defines the gain of the potentiometer signal input.
P244 - Potentiometer Signal Offset
Range: -100.0 to 100.0 % Default: 0.0 %

Description:
This parameter defines the offset of the potentiometer signal input.
P245 - Potentiometer and FI1 Filter

Description:
This parameter sets the filter time constant of the potentiometer signal (when the accessory is connected) and of
the frequency input. It attenuates sudden changes in its value.
9-6 | CFW300
I/O
9.4 ANALOG OUTPUTS
The analog output (AOx) is configured by means of three types of parameters: Function, Gain and Signal, according
to the block diagram in Figure 9.4 on page 9-7.
The quantity of analog outputs depends on the expansion accessory IO’s. For further details, refer to the installation,
configuration and operation guide of the IO’s expansion accessory used.
AO1 - P014
AO2 - P015
Function Signal
Gain
AO1 - P251 AO1 - P253
AO1 - P252
AO2 - P254 AO2 - P256
AO2 - P255
Value
AO1(*)
AO2(*)
(*) Control terminals available on the accessory.
Figure 9.4: Block diagram of the analog output (AOx)
P014 - AO1 Value
P015 - AO2 Value
Range: 0.0 to 100.0 % Default:
Properties: ro
Description: 9
These read-only parameters indicates the value of analog outputs AO1 and AO2 in percentage of the full scale.
The indicated values is obtained after multiplication by the gain. Check the description of the parameters P251 to
P256.
P251 - AO1 Output Function
CFW300 | 9-7
I/O
P254 - AO2 Output Function

1 = Not Used
2 = Real Speed
3 to 4 = Not Used
5 = Output Current
6 = Not Used
7 = Active Current
8 to 10 = Not Used
11 = Motor Torque
12 = SoftPLC
13 to 15 = Not Used
16 = Motor Ixt
17 = Not Used
18 = P696 Value
19 = P697 Value
20 = Not Used
Description:
These parameters sets the functions of the analog outputs, according to function and scale presented in Table 9.2
on page 9-8.
9 Table 9.2: Full scale of the analog output

Function Description Full Scale
0 Speed reference at the input of the ramp P001 P134
2 Effective speed at the inverter output P134
5 Total output current RMS 2 x P295
7 Active Current 2 x P295
11 Torque on the motor in relation to the rated torque 200.0 %
12 SoftPLC scale for analog output 32767
16 Ixt overload of the motor (P037) 100 %
18 Value of P696 for analog output AOx 32767
19 Value of P697 for analog output AOx 32767
21 to 28 Value defined by the SoftPLC application 32767
29 Control Setpoint (PID Controller Application) (*)
30 Process Variable (PID Controller Application) (*)
(*) For further details refer the Chapter 14 APPLICATIONS on page 14-1.
P252 - AO1 Output Gain
P255 - AO2 Output Gain
Range: 0.000 to 9.999 Default: 1.000
9-8 | CFW300
I/O
Description:
It determines the analog outputs gain according to the equations of Table 9.3 on page 9-9.
P253 - AO1 Output Signal
P256 - AO2 Output Signal
Range: 0 = 0 to 10 V Default: 0
1 = 0 to 20 mA
2 = 4 to 20 mA
3 = 10 to 0 V
4 = 20 to 0 mA
5 = 20 to 4 mA
Description:
These parameters configures if the analog outputs signal will be in current or voltage, with direct or reverse reference.
Table 9.3 on page 9-9 below summarizes the configuration and equation of the analog output, where the relationship
between the analog output function and the full scale is defined by P251 (AO1) or P256 (AO2), as per Table 9.2 on
page 9-8.
Table 9.3: Configuration and equations characteristic of AOx

Signal P253 or P256 Equation
( )
function
0 to 10 V 0 AOx(%) = x gain x 10 V
scale
( )
function
0 to 20 mA 1 AOx(%) = x gain x 20 mA
scale
( )
function
4 to 20 mA 2 AOx(%) = x gain x 16 mA + 4 mA
scale
( ) 9
function
10 to 0 V 3 AOx(%) = 10 V - x gain x 10 V
scale
( )
function
20 to 0 mA 4 AOx(%) = 20 mA - x gain x 20 mA
scale
( )
function
20 to 4 mA 5 AOx(%) = 20 mA - x gain x 16 mA
scale
P696 - AOx Value 1
P697 - AOx Value 2
Range: 0 to FFFF (hexa) Default:
Properties: ro
Description:
Parameters used for monitoring and controlling the inverter by using the communication interfaces. For detailed
description, refer to the communication manual (User) according to the interface used. These manuals are they are
CFW300 | 9-9
I/O
available for download on the website: www.weg.net.
9.5 FREQUENCY INPUT
A frequency input consists of a fast digital input able to convert the frequency of the pulses in the input into a
proportional signal with 15-bit resolution. After the conversion, this signal is used as an analog signal for frequency
reference, process variable, for example.
According to the block diagram of Figure 9.5 on page 9-10, the signal in frequency is converted into a digital
quantity in 15 bits by means of the block “Calc. Hz / %”, where parameters P248 and P250 define the input signal
frequency band, while parameter P022 shows the frequency of the pulses in Hz.
Signal FI
(via DIx)
FI(Hz) - P022
FI (Hz)
Calc. Hz / %
(Hz)
Filter
P250 FI (%) Gain

FI - P247 P245
P248
100 (%)
Offset
FI - P249 Value FIx Function
(internal) FI - P246
Figure 9.5: Block diagram of frequency input - FI (DIx)
Digital input DIx is pre-defined for frequency input via parameter P246, with operating capacity in a wide band from
1 to 3000 Hz.
Parameters P248 and P250 determine the operation range of the frequency input (FI), while parameters P249 and
P247 determine the offset and gain, respectively, according to with the equation:
9 (( ) )
FI (Hz) - P248
FI = x (100 %) + P249 x P247
P250 - P248
For example, FI = 2000 Hz, P248 = 1000 Hz, P250 = 3000 Hz, P249 = -70.0 % and P247 = 1.000, thus:
(( ) )
2000 - 1000
FI = x (100 %) - 70 % x 1.000 = -20.0 %
3000 - 1000
The value FI = -20.0 % means that the motor will run in the opposite direction with a reference in module equal
20.0 % of P134, with the function of the FI signal for “Frequency Reference” (P221 = 4).
When P246 = 3, the digital input DI3 is defined for frequency input, regardless the value of P265, with operating
capacity in the band from 0 to 3000 Hz in 10 Vpp.
The time constant of the digital filter for the frequency input is defined by means of parameter P245.
P022 - FI Value in Hz
Range: 0 to 3000 Hz Default:
Properties: ro
Description:
Value in hertz of the frequency input FI.
9-10 | CFW300
I/O
✓
NOTE!
The operation of parameters P022 as well as of the frequency input, depends on the configuration of
the parameter P246.
P246 - FI1 Input Function

1 = Active in DI1
2 = Active in DI2
3 = Active in DI3
4 = Active in DI4
Properties: cfg
Description:
When set to “0” the frequency input is inactive, keeping parameter P022 at zero. In the other cases, this parameter
activates the frequency input on the DIx, making any other function in this digital input DIx (P263-P266) be ignored,
and the value of its respective bit in parameter P012 is kept at “0”. In order to do so, it is also necessary to configure
parameters P221 and/or P222, selecting the use of the frequency input.
P247 - FI1 Input Gain
Range: 0.000 to 9.999 Default: 1.000

Description:
It sets the gain of the frequency input.
P248 - FI1 Minimum Input

9
Description:
It sets the minimum value of the frequency input.
P249 - FI1 Input Offset
Range: -100.0 to 100.0 % Default: 0.0 %

Description:
It sets the offset of the frequency input.
P250 - FI1 Maximum Input

Description:
It sets the maximum value of the frequency input.
9.6 DIGITAL INPUTS
Below is a detailed description of the parameters for the digital inputs.
CFW300 | 9-11
I/O
P012 - DI8 to DI1 Status
Range: 0 to FF (hexa) Default:

Bit 0 = DI1
Bit 1 = DI2
Bit 2 = DI3
Bit 3 = DI4
Bit 4 = DI5
Bit 5 = DI6
Bit 6 = DI7
Bit 7 = DI8
Properties: ro
Description:
Using this parameter, it is possible to view the status of the digital inputs, according to the IO’s expansion accessory
connected. Refer to parameter P027 in Section 6.2 ACCESSORIES on page 6-3.
The value of P012 is indicated in hexadecimal, where each bit of the number indicates the state of a digital input,
that is, if Bit 0 is “0”, DI1 is inactive, or if Bit 0 is “1”, DI1 is active, and so on up to DI8. Besides, the determination
of DIx active or inactive takes into account the type of signal of DIx defined by P271.
The activation of DIx depends on the signal at the digital input and on P271, as per Table 9.4 on page 9-12. Which
lists the threshold voltage for activation “VTH ”, the threshold voltage for deactivation “VTL ”and the status indication
of DIx in parameter P012.
Table 9.4: Values of P012 for x from 1 to 8

Set in P271 Limit Voltage in DIx P012
VTL >10 V Bitx-1 = 0
NPN
VTH <5 V Bitx-1 = 1
VTL <10 V Bitx-1 = 0
PNP
VTH >20 V Bitx-1 = 1
✓
NOTE!
Parameter P012 requires the user to know the conversion between binary and hexadecimal numerical
9 system.
P263 - DI1 Input Function
9-12 | CFW300
I/O
Range: 0 = Not Used Default: 1

1 = Run/Stop
2 = General Enable
3 = Quick Stop
4 = Forward Run
5 = Reverse Run
6 = Start
7 = Stop
9 = LOC/REM
10 = JOG
13 = Multispeed
14 = 2nd Ramp
15 to 17 = Not Used
18 = No Ext. Alarm
19 = No Ext. Fault
20 = Reset
21 to 23 = Not Used
24 = Disab. Flying Start
25 = Not Used
26 = Lock Prog.
27 to 31 = Not Used
38 = Dec. E.P. / Stop 9
39 = Stop
40 = Safety Switch
50 to 54 = Not Used
55 = Run/Stop with Line Start Lockout
56 = Forward Run with Line Start Lockout
57 = Reverse Run with Line Start Lockout
Properties: cfg
Description:
These parameters allow configuring the digital input function, according to the adjustable range listed in Table 9.5
on page 9-14.
CFW300 | 9-13
I/O
Table 9.5: Digital Input Functions

Value Description Dependence Figure (Page)
0 Not used - -
1 Run/Stop command P224 = 1 or P227 = 1 9.6 (9-15)
2 General Enable command - 9.7 (9-15)
3 Fast Stop P224 = 1 or P227 = 1 9.8 (9-15)
(P224 = 1 and P223 = 4) or
4 Forward run command 9.9 (9-16)
(P227 = 1 and P226 = 4)
5 Reverse run command P224 = 1 or P227 = 1 9.9 (9-16)
6 Start command P224 = 1 or P227 = 1 9.10 (9-16)
7 Stop command P224 = 1 or P227 = 1 9.10 (9-16)
8 Forward Rotation Direction P223 = 4 or P226 = 4 9.11 (9-17)
9 Local/Remote selection P220 = 4 -
(P224 = 1 and P225 = 2) or
10 JOG command 9.12 (9-17)
(P227 = 1 and P228 = 2)
11 Electronic Potentiometer: Accelerate E.P. P221 = 7 or P222 = 7 9.13 (9-18)
12 Electronic Potentiometer: Decelerate E.P. P221 = 7 or P222 = 7 9.13 (9-18)
13 Multispeed reference P221 = 8 or P222 = 8 -
14 2nd Ramp selection P105 = 2 9.14 (9-18)
15 to 17 Not used - -
18 No external alarm - -
19 No external fault - -
20 Fault reset Active fault -
24 Disable flying start P320 = 1 or 2 -
25 Not used - -
26 Lock Prog. - -
32 Multispeed reference with 2nd Ramp (P221 = 8 or P222 = 8) and P105 = 2 -
33 Electronic Potentiometer: Accelerates E.P. with 2nd Ramp (P221 = 7 or P222 = 7) and P105 = 2 -
34 Electronic Potentiometer: Decelerates E.P. with 2nd Ramp (P221 = 7 or P222 = 7) and P105 = 2 -
(P224 = 1 and P223 = 4) or
35 Forward run with 2nd Ramp -
(P227 = 1 and P226 = 4) and P105 = 2
(P224 = 1 and P223 = 4) or
36 Reverse run with 2nd Ramp -
(P227 = 1 and P226 = 4) and P105 = 2
(P224 = 1 or P227 = 1) and
37 Accelerates E.P./Start 9.15 (9-19)
9 (P221 = 7 or P222 = 7)
(P224 = 1 or P227 = 1) and
38 Decelerates E.P./ Stop 9.15 (9-19)
(P221 = 7 or P222 = 7)
39 Stop command P224 = 1 or P227 = 1 9.16 (9-19)
40 Safety switch command P224 = 1 or P227 = 1 9.17 (9-20)
41 Application Function 1 - -
49 Activate Fire Mode - -
50 Manual/Automatic PID (Only DI2 for P903 = 1) (*) -
51 Increase Setpoint Command (PE) (Only DI3 for P903 = 1) (*) -
52 Decrease Setpoint Command (Only DI4 for P903 = 1) (*) -
53 1st DI Control Setpoint (Only DI3 for P903 = 1) (*) -
54 2nd DI Control Setpoint (Only DI4 for P903 = 1) (*) -
55 Run/Stop with Line Start Lockout - -
56 Forward Run with Line Start Lockout - -
57 Reverse Run with Line Start Lockout - -
(*) For further details refer the Chapter 14 APPLICATIONS on page 14-1.
9-14 | CFW300
I/O
P271 - DIs Function
Range: 0 = (DI1..DI8) NPN Default: 0

1 = (DI1..DI4) PNP
2 = (DI5..DI8) PNP
3 = (DI1..DI8) PNP
Properties: cfg
Description:
It configures the default for the digital input signal, that is, NPN and the digital input is activated with 0 V, PNP and
the digital input is activated with +24 V.
a) RUN/STOP
It enables or disables the motor rotation through the acceleration and deceleration ramp (Figure 9.6 on page
9-15).
Acceleration Deceleration
ramp ramp
Output
frequency
Time
Active
DIx Inactive
Time
Figure 9.6: Example of the Run/Stop function
b) GENERAL ENABLE
It enables the motor rotation through the acceleration ramp and disables it by cutting off the pulses
immediately; the motor stops by inertia (Figure 9.7 on page 9-15).
Acceleration ramp Motor runs free
Output 9
frequency
Time
Active
DIx Inactive
Time
Figure 9.7: Example of the General Enable function
c) QUICK STOP
When inactive, it disables the inverter by the emergency deceleration (P107) (Figure 9.8 on page 9-15).
Acceleration
P107 - Deceleration
ramp
ramp
Output
frequency
Time
Active
DIx Inactive
Time
Figure 9.8: Example of the Quick Stop function
CFW300 | 9-15
I/O
d) FORWARD/REVERSE COMMAND
This function is the combination of two DIS: one programmed for forward run and the other for reverse run
(Figure 9.9 on page 9-16).
Active
DIx - Forward Active
Time
Active
DIx - Reverse Active
Time
Output
Forward
frequency
Reverse Time
Figure 9.9: Example of the Forward /Reverse command
e) START/STOP
This function tries to reproduce the activation of a three-wire direct start with retention contact, where a pulse
in the DIx-Start enables the motor spin while the Dlx-Stop is active (Figure 9.10 on page 9-16).
Active
DIx - Start Inactive

Time
Active
DIx - Stop Inactive

9 Time
Output
frequency
Time
Figure 9.10: Example of the Start/Stop
✓
NOTE!
All the digital inputs set for General Enable, Fast Stop, Forward Run/Reverse Run and Start/Stop
must be in the “Active” state so that the inverter can enable the motor run.
f) DIRECTION OF ROTATION
If the DIx is Inactive, the Direction of Rotation is Forward, otherwise, the direction of rotation will be reverse
9-16 | CFW300
I/O
Forward
Output
frequency
Time
Reverse
Active
DIx Inactive
Time
Figure 9.11: Example of the Direction of Rotation function
g) LOCAL/REMOTE
If DIx is inactive, the Local command is selected, reverse the Remote command is selected.
h) JOG
The JOG command is the combination of the Run/Stop command with a speed reference via parameter P122
JOG frequency
Acceleration
(P122)
ramp
Output Deceleration
frequency ramp
Time
DIx - Active
Run/Stop Inactive
Time
Active
DIx - JOG Inactive 9
Time
DIx - Active
General Enable Inactive
Time
Figure 9.12: Example of the JOG function
i) ELECTRONIC POTENTIOMETER
The E.P. function enables the setting of the speed via digital inputs programmed for Accelerate E.P. and
Decelerate E.P. (Figure 9.13 on page 9-18). The basic principle of this function is similar to the sound volume
and intensity control of electronic appliances.
The operation of the E.P. function is also affected by the behavior of parameter P120, that is, if P120 = 0 the
E.P. reference initial value will be P133; if P120 = 1 the initial value will be the last reference value before the
disabling of the inverter, and if P120 = 2, the initial value will be the reference via P121 keys.
CFW300 | 9-17
I/O
DIx - Accelerate
RAMP Reference
DIx - Decelerate
& Reset Speed

Enabling (RUN)
P133
Output
frequency
Active Time
DIx - Accelerate
Inactive
Reset Time
Active
DIx - Decelerate
Inactive
Active Time
DIx - Run/Stop Inactive

Time
Figure 9.13: Example of the Electronic Potentiometer (E.P.) function
j) MULTISPEED
The Multispeed reference, as described in Section 7.2 SPEED REFERENCE on page 7-6, enables, by means
of the combination of up to three digital inputs, the selection of one from eight reference levels predefined in
parameters P124 to P131.
For further details, refer to Chapter 7 COMMAND AND REFERENCES on page 7-1.
k) 2nd RAMPA
If DIx is inactive, the inverter uses the default ramp by P100 and P101, otherwise, it will use the 2nd Ramp by
P102 and P103 (Figure 9.14 on page 9-18).
9
Active
DIx - Run/Stop Inactive

Time
Active
DIx - 2nd ramp Inactive

Time
P102 P103
P100 P101
Output
frequency
Time
Figure 9.14: Example of the 2nd Ramp function
l) NO EXTERNAL ALARM
If DIx is inactive, the inverter will activate the external alarm A090.
m) NO EXTERNAL FAULT
If DIx is inactive, the inverter will activate the external fault F091. In this case, the PWM pulses are disabled
immediately.
9-18 | CFW300
I/O
n) FAULT RESET
Once the inverter is with the fault state active, and the fault origin condition is no longer active. The reset of
the fault state will occur when the DIx set for this function is active.
o) DISABLE FLYING START

It allows the DIx, when active, to disable the action of the Flying Start function preset in parameter P320 = 1 or
2. When the DIx is inactive, the Flying Start function operates normally again. Refer to Section 8.1 COMMON
FUNCTIONS on page 8-1 for more information.
p) LOCK PROG
When the DIx input is active, parameters cannot be changed, no matter the values set in P000 and P200.
When the DIx input is Inactive, the modification of parameters will depend on the values set in P000 and
P200.
q) ACCELERATE E.P. - TURN ON / DECELERATE E.P. - TURN OFF

It consists of the Electronic Potentiometer function with capacity to enable the inverter by means of a pulse
at the start, and a pulse for the stop when the output speed is minimum (P133) (Figure 9.15 on page 9-19).
P134
(Fmax)
P133 P133
(Fmin) (Fmin)
Output
frequency
Time
Active
Pulse
DIx - Accelerate/ Turn ON
Turn ON Inactive
Time
Active
Pulse
DIx - Decelerate/ Turn OFF
Turn OFF Inactive
Time 9
Figure 9.15: Example of the Accelerate Turn ON / Decelerate Turn OFF
r) STOP
Only on pulse in the DIx disables the inverter (Figure 9.16 on page 9-19).
Deceleration
ramp
Output
frequency
Time
Active
DIx - Stop Inactive

Time
Figure 9.16: Example the stop function
s) SAFETY SWITCH
Only one inactive pulse in the DIx disables the inverter (Figure 9.17 on page 9-20).
CFW300 | 9-19
I/O
Deceleration
Output ramp
frequency
Time
Active
DIx - Safety
switch Inactive
Time
Figure 9.17: Example of the Emergency function
9.7 INPUT FOR INFRARED RECEIVER
The IOADR accessory uses an infrared remote control to control the inverter. The RC-5 protocol (Philips) was used
for the communication of the control with the accessory. The information on the control/selection of remote control
is available in the parameters below.
P840 - IR Control Command
Properties: ro
Description:
By means of this parameter it is possible to check if the frequency inverter is receiving any valid command from
the infrared control. The use of the remote control depends on the logic implanted on the LADDER of the WPS
software via system markers (bits). For further details, refer to the help menu of the WPS software.
P841 - IR Controle Selection
Range: 0 = Without Display Default: 0

9 1 = With Display
Properties: cfg
Description:
Through this parameter it is possible to select which infrared remote control will be used. For further details, refer
to the installation, configuration, and operation guide of the I/O IOADR expansion module .
9.8 ENCODER INPUT
The IOAENC expansion module makes it possible to connect an incremental encoder to the frequency inverter.
The speed (RPM) and pulse count are available to user by parameters.
Below is a detailed description of the parameters for the encoder input.
P038 - Encoder Speed
Range: -9999 to 9999 rpm Default:
Properties: ro
Description:
This parameter presents the instant speed of the encoder in revolutions per minute (RPM); the measurement is not
filtered and it is updated every 6 ms.
9-20 | CFW300
I/O
P039 - Encoder Pulses Count
Properties: ro
Description:
Using this parameter it is possible to check the number of pulses counted from the encoder in quadrature. The
count can be incremented from 0 to 9999 (clockwise) or decremented from 9999 to 0 (counterclockwise).
P191 - Clear Enc. Pulse Counter
Range: 0 = No Default: 0
1 = Yes
Properties: cfg
Description:
The clear counter function aims to synchronize the minimum or maximum count at the parameter P039 - Encoder
Pulse Counter, with the application limits (limit switches).
This parameter starts with zero value at the frequency inverter power-on. When adjusted to one (P191 = 1) the
function is activated. After the function turn on, the parameter P039 is cleared or setted up with maximum count
value (9999), according with the direction of rotation.
At the end of P039 clearing, the value of parameter, P191, returns to zero, allowing perform the process again, if
necessary.
P358 - Encoder Fault Config.

1 = F067 ON
2 = F079 ON
3 = F067 and F079 ON 9
Properties: cfg
Description:
This parameter allows individually disabling the fault detection by software: a) F067 - Inverted Encoder/Motor Wiring
and b) F079 - Encoder Signal Fault. The verification by software of faults F067 and F079 will remain disabled when
P358 = 0.
P405 - Encoder Pulses Number

Description:
It sets the number of pulses per revolution (ppr) of the incremental encoder. This parameter influences the indication
of the speed parameters (P038) and pulse counter (P039) of the encoder.
✓
NOTE!
The encoder input is not used to motor vector control, and must be applied when there is no
requirement to high performance.
CFW300 | 9-21
I/O
9.9 DIGITAL OUTPUTS
The frequency inverter can activate relay digital outputs available at product and/or accessory. The parameter
configuration of the digital outputs behaves as described in detail below.
P013 - DO4 to DO1 Status
Range: 0 to F (hexa) Default:

Bit 0 = DO1
Bit 1 = DO2
Bit 2 = DO3
Bit 3 = DO4
Properties: ro
Description:
Using this parameter, it is possible to view the inveter digital outputs status.
The P013 value is indicated in hexadecimal, where each bit of the number indicates the status of a digital output,
that is, if Bit0 is “0”, DO1 is inactive; if Bit0 is “1”, DO1 is active.
✓
NOTE!
Parameter P013 requires the user to know the conversion between binary and hexadecimal numerical
system.
P275 - DO1 Function
P276 - DO2 Function
P277 - DO3 Function
9-22 | CFW300
I/O
P278 - DO4 Function
Range: 0 = Not Used Default: 13

1 = F* ≥ Fx
2 = F ≥ Fx
3 = F ≤ Fx
4 = F = F*
5 = Not Used
6 = Is > Ix
7 = Is < Ix
8 = Torque > Tx
9 = Torque < Tx
10 = Remote
11 = Run
12 = Ready
13 = No Fault
14 = No F070
15 = Not Used
16 = No F021/F022
17 = Not Used
18 = No F072
19 = 4-20 mA OK
20 = P695 Value
21 = Forward
22 to 23 = Not Used
24 = Ride-Through
25 = Pre-Charge OK
26 = Fault
27 = Not Used
28 = SoftPLC
29 to 34 = Not Used
35 = No Alarm
36 = Without fault and alarm 9
45 = Fire Mode ON
46 = Low Level of Process Variable
47 = High Level of Process Variable
Description:
These parameters define the DOx digital output function, as per Table 9.6 on page 9-24.
CFW300 | 9-23
I/O
Table 9.6: Digital Output Functions

Value Function Description
0 Not Used It deactivates the digital output
1 F* ≥ Fx Active when the frequency reference F* (P001) is greater or iqual the Fx (P281)
2 F ≥ Fx Active when the Output Frequency F (P002) is greater or iqual the Fx (P281)
3 F ≤ Fx Active when the Output Frequency F (P002) is smaller or iqual the (P281)
4 F = F* Active if the Output Frequency F (P002) is equal to the reference F* (P001) (ramp end)
6 Is > Ix Active if the output current Is (P003) > Ix (P290)
7 Is < Ix Active if the output current Is (P003) < Ix (P290)
8 Torque > Tx Active if the motor torque T (P009) > Tx (P293)
9 Torque < Tx Active if the motor torque T (P009) < Tx (P293)
10 Remote Active if the command is in the remote situation (REM)
11 Run Active if the motor is running (active output PWM pulses)
12 Ready Active if the inverter is ready for enabling
13 Without fault Active if the inverter has no faults
14 Without F070 Active if the inverter has no overcurrent fault (F070)
16 Without F021/F022 Active if the inverter has no overvoltage or undervoltage fault (F022 or F021)
18 Without F072 Active if the inverter has no motor overload fault (F072)
19 4-20 mA OK Active if AIx setting is 4 to 20 mA (P233 = 1 or 3) and AIx > 2 mA
20 Value of P695 Status of the bits 0 to 4 of P695 activate digital outputs DO1 to DO5, respectively
21 Forward Active if the inverter direction of rotation is forward
22 and 23 Not Used It deactivates the digital output
24 Ride-Through It activates if the inverter is running a function Ride-Through
25 Pre-Charge OK Active if the pre-charge relay of the DC link capacitors was already activated
26 With fault Active if the inverter has a fault
28 SoftPLC It activates the output DOx according to the SoftPLC memory area. Check the SoftPLC user manual
29 to 34 Not Used It deactivates the digital output
35 Without Alarm Active when the inverter has no alarms
36 Without fault and alarm Active when the inverter has neither alarms nor faults
37 Application Fuction 1 If activates the output DOx according to the application of SoftPLC
9 41 Application Fuction 5 If activates the output DOx according to the application of SoftPLC
45 Fire Mode Activates DOx output when Fire Mode is enabled
46 Process Control Process Variable Low Level (A760/F761) (For P903 = 1)(*)
47 Process Control Process Variable High Level (A762/F763) (For P903 = 1)(*)
(*) For further details refer the Chapter 13 SOFTPLC on page 13-1.
P281 - Fx Frequency

Description:
This parameter sets the actuation level on the output frequency signal Fx and on the ramp input F* of the digital
relay output.
In this way, the relay commutation levels are “P281 + P282” and “P281 - P282”.
9-24 | CFW300
I/O
P282 - Fx Hysteresis

Description:
This parameter sets the hysteresis on the output frequency signal Fx and on the ramp input F* of the digital relay
output.
In this way, the relay commutation levels are “P281 + P282” and “P281 - P282”.
P290 - Ix Current

Description:
Current level to activate the relay output in the Is > Ix (6) and Is < Ix (7) functions. The actuation occurs on a
hysteresis with upper in P290 and lower level in: P290 - 0.05 x P295, that is, the equivalent value in Amperes for
5 % of P295 below P290.
P293 - Tx Torque

Description:
Torque percentage level to activate the relay output in the Torque > Tx (8) and Torque < Tx (9) functions. The
actuation occurs on a hysteresis with upper level in P293 and lower level in: P293 - 5 %. This percentage value
is related to the motor rated torque matched to the inverter power, and it is expressed in percentage of the motor
rated current (P401 = 100 %).
P695 - DOx Value
Range: 0 to 7F (hexa) Default: 9

Bit 0 = DO1
Bit 1 = DO2
Bit 2 = DO3
Bit 3 = DO4
Properties: ro
Description:
Parameters used for monitoring and controlling the inverter by using the communication interfaces. For a detailed
description, refer to the user manual of the communication network, available for download on the website:
www.weg.net.
CFW300 | 9-25
I/O
9-26 | CFW300
FAULTS AND ALARMS
10 FAULTS AND ALARMS
The problem detection structure in the inverter is based on the fault and alarm indication.
In case of fault, the locking the IGBTs and motor stop by inertia will occur.
The alarm works as a warning for the user of critical operating conditions and that may cause a fault if the situation
is not corrected.
10.1 FAULT HISTORY
The inverter is able to store a set of data on the last three faults occurred, such as: fault number, current (P003),
DC link voltage (P004), output frequency (P005), power module temperature (P030).
P048 - Present Alarm
P049 - Present Fault
Properties: ro
Description:
These parameters indicate the alarm (P048) or the fault (P049) number that may be present in the inverter.
P050 - Last Fault
P060 - Second Fault
P070 - Third Fault
Properties: ro
Description: 10
These parameters indicates the number of the occurred fault.
P051 - Current At Last Fault
Range: 0.0 to 40.0 A Default:
Properties: ro
Description:
It indicates the output current at the moment of the last occurred fault.
P052 - DC Link At Last Fault
Range: 0 to 828 V Default:
Properties: ro
CFW300 | 10-1
FAULTS AND ALARMS
Description:
It indicates the DC link voltage at the moment of the last occurred fault.
P053 - Frequency At Last Fault
Range: 0.0 to 400.0 Hz Default:
Properties: ro
Description:
If indicates the output frequency at the moment of the last occurred fault.
P054 - Temperature Last Fault
Range: 0.0 to 200.0 ºC Default:
Properties: ro
Description:
It indicates the IGBTs temperature at the moment of the last occurred fault.
P080 - Last Fault on Fire Mode
P081 - Second Fault on Fire Mode
P082 - Third Fault on Fire Mode
Properties: ro
Description:
These parameters indicate the last three faults that occurred on the inverter while the Fire Mode was active.
10 10.2 FAULT CONTROL
The parameters related to the control of the motor protections of operation and the inverter are in this group.
P340 - Auto-Reset Time
Range: 0 to 255 s Default: 0s

Description:
It defines the interval after a fault (except F067: Incorrect Encoder/Motor Wiring) to activate the inverter autoreset.
If the value of P340 is zero the fault autoreset function is disabled.
✓
NOTE!
The function auto-reset is locked if the same fault occurs three times in a row within 30 seconds after
the reset.
10-2 | CFW300
FAULTS AND ALARMS
10.3 PROTECTIONS
This section contains information on the internal protections of the inverters and the motors. Refer to the user’s
manual for further information.
10.3.1 Inverter
The inverter has several levels of internal protection. Among them, we can point out:
10.3.1.1 DC Link Voltage Supervision
The DC link voltage is constantly compared to the maximum and minimum values according to the inverter power
supply, as shown in Table 10.1 on page 10-3.
Table 10.1: Levels of performance monitoring of the DC link voltage

Supply Level F021 Level F022
110 to 127 Vac (P296 = 1) 200 Vdc 460 Vdc
200 to 240 Vac (P296 = 2) 200 Vdc 410 Vdc
380 Vac (P296 = 4) 385 Vdc 800 Vdc
400 to 415 Vac (P296 = 5) 405 Vdc 800 Vdc
440 to 460 Vac (P296 = 6) 446 Vdc 800 Vdc
480 Vac (P296 = 7) 486 Vdc 800 Vdc
10.3.1.2 Temperature control
The temperature of the power module is read via internal temperature sensor and displayed in parameter P030
(more information on Chapter 11 READ on page 11-1. The temperature controlled by a fan according to parameter
P352.
P352 - Fan Control Config.
Range: 0 = OFF Default: 2

1 = ON
2 = CT
Properties: cfg
10
Description:
The inverter is equipped with a heatsink fan, and the activation will be controlled via software by means of the
inverter programming.
The options available to set this parameter are described in Table 10.2 on page 10-3:
Table 10.2: Option of parameter P352

P352 Action
0 = OFF Fan off
1 = ON Fan on
2 = CT Fan is controlled via software
10.3.2 Motor
The inverter has a function to protect the motor from overtemperature by indicating fault F078. The motor must
have a triple PTC type temperature sensor. The sensor can be read through the analog inputs.
For the reading of the PTC, it is necessary to configure it for current input and select the option “4 = PTC” in P231
or P236. Connect the PTC between the supply +10 Vdc and the analog input.
CFW300 | 10-3
FAULTS AND ALARMS
The analog input reads the PTC resistance and compares it to the limits for the fault. When those values are
exceeded, fault F078 is indicated. As shown in Table 10.3 on page 10-4.
WARNING!
! The PTC must have reinforced insulation of the live parts of the motor and other installations.
Table 10.3: Actuation levels of fault F078

PTC Resistance AIx Overtemperature
RPTC < 50 Ω Vin > 9.1 V F078
50 Ω < RPTC < 3.9 kΩ 9.1 V > Vin > 1.3 V Standard
RPTC > 3.9 kΩ Vin < 1.3 V F078
✓
NOTE!
For this function to work properly, it is important to keep the gain(s) and offset(s) of the analog inputs
at the factory setting values.
Figure 10.1 on page 10-4 shows the connection of the PTC to the inverter terminals via analog input.
+ 10 V
PTC
AIx (0 .. 4 to 20 mA)
Figure 10.1: Connection of the PTC to the frequency inverter
P037 - Motor Overload Ixt
10 Properties: ro
Description:
It indicates the present motor overload percentage or overload intergrator level. When this parameter reaches 6.3
% the inverter will indicate the motor overload alarm (A046). Or when this parameter reaches 100.0 % the “Motor
Overload” fault (F072) will occur (F072).
Figure 10.2 on page 10-5 shows the actuation time of the overload as a function of the output current (P003)
normalized in relation to the overload current (P156, P157 or P158).
For example, for a constant ratio with 150 % of overload, Fault F072 occurs in 60 seconds. On the other hand, for
output current values below P156, P157 or P158 according to the output frequency, fault F0072 does not occur.
For ratio values above 150 % the fault actuation time is below 60 s.
10-4 | CFW300
FAULTS AND ALARMS
2,5
2 Region of overload
Overload current
Output current
1,5
0,5
0
0 60 120 180 240 300
Time (s)
Figure 10.2: Actuation of the motor overload
✓
NOTE!
In order to ensure greater protection in case of de-energization of the inverter, this function keeps the
information regarding the motor thermal image in a non-volatile memory area of the inverter. Thus,
after the inverter energization, the function will use the saved value of the thermal image to execute a
new overload assessment.
P156 - Rated Speed Overload Current
P157 - Overl.Curr.50 % Speed

10
P158 - Overl.Curr.20 % Speed

Description:
These parameters define the motor overload current (Ixt - F072). The motor overload current is the current value
(P156, P157 or P158) based on which the inverter will understand that the motor is operating in overload.
For self-ventilated motors, the overload current depends on the speed at which the motor is spinning. Therefore,
for speeds below 20 % of the rated speed, the overload current is P158, while for speeds between 20 % and 50
% the overload current is P157, and above 50 % it is P156.
The greater the difference between the motor current and the overload current (P156, P157 or P158) the faster the
actuation of fault F072.
It is recommended that parameter P156 (motor overload current at rated speed) be set at a value 10 % above the
used motor rated current (P401).
In order to deactivate the motor overload function, just set parameter P156 to P158 to values equal to or above
twice the inverter rated current P295.
CFW300 | 10-5
FAULTS AND ALARMS
10
10-6 | CFW300
READ
11 READ
It is important to point out that all the parameters of this group can only be viewed on the HMI display, and cannot
be changed by the user.
P001 - Speed Reference
Properties: ro
Description:
This parameter presents, regardless the origin source, the speed reference value in the unit and scale defined for
the reference by P208, P209 and P210. The full scale and reference unit in the factory default are 60.0 Hz for P204
= 5 and 50.0 Hz for P204 = 6.
P002 - Output Speed (Motor)
Properties: ro
Description:
Parameter P002 indicates the speed imposed to the inverter output at the same scale defined for P001. In this
parameter, the compensations made to the output frequency are not shown. In order to see them, use P005.
P003 - Motor Current
Range: 0.0 to 40.0 A Default:
Properties: ro
Description:
It indicates the inverter output current in amperes RMS (Arms).
P004 - DC Link Voltage
Range: 0 to 828 V Default: 11

Properties: ro
Description:
It indicates the DC link direct current voltage in (V).
P005 - Output Frequency (Motor)
Range: 0.0 to 400.0 Hz Default:
Properties: ro
Description:
Real frequency instantly applied to the motor in Hertz (Hz).
CFW300 | 11-1
READ
P006 - Inverter Status
Range: 0 = Ready Default:

1 = Run
2 = Undervoltage
3 = Fault
4 = Self-Tuning
5 = Configuration
6 = DC Braking
7 = Reserved
8 = Fire Mode
Properties: ro
Description:
It indicates one of the possible inverter status. In Table 11.1 on page 11-3 contains the description of each state,
as well as the indication on the HMI.
11
11-2 | CFW300
READ
Table 11.1: Inverter status - P006
P006 Status HMI Description
0 Ready Indicates the inverter is ready to be enabled
1 Run Indicates the inverter is enabled
Indicates the voltage in the inverter is too low for

2 Sub operation (undervoltage), and will not accept the
enabling command
Indicates the inverter is in the fault status. The fault

3 Fault
code will flash
Indicates the inverter is executing the Self-Tuning

4 Self-tuning
routine
Indicates the inverter has incompatible parameter

programming. After pressing the key, it will
keep showing an arrow until the incorrect setting
5 Configuration
is corrected, as shown in the figure. The situations
of CONFIG status are shown in the Table 11.3 on
page 11-5
Indicates the inverter is applying DC Braking during

6 DC Braking
motor start and/or motor stop
7 Reserved - -
Indicates that the inverter is in Fire Mode. After

8 Fire Mode pressing the key, letter “A” will continue to flash
indicating the state
11
P007 - Output Voltage
Range: 0 to 480 V Default:
Properties: ro
Description:
It indicates the line voltage in inverter output, in Volts (V).
CFW300 | 11-3
READ
P009 - Motor Torque
Properties: ro, VVW

Description:
It indicates the torque developed by the motor in relation to the rated torque.
P030 - Module Temperature
Range: -200.0 to 200.0 ºC Default:
Properties: ro
Description:
The temperature of the power module is monitored and indicated in parameter P030 in degrees Celsius. This value
is constantly compared to the overtemperature fault and alarm tripping value of the power module F051 and A050,
according to Table 11.2 on page 11-4.
Table 11.2: Overtemperature actuation levels of the power module

Line Frame Size Level A050 Level F051
200 V A 90 °C (194 °F) 100 °C (212 °F)
200 V B 116 °C (248 °F) 126 °C (258 °F)
400 V A, B and C 100 °C (212 °F) 110 °C (222 °F)
In addition to the indication of alarm A050, the overtemperature protection gradually reduces the switching
frequency to 2.5 kHz. This overtemperature protection characteristic can be disabled in the control configuration
parameter P397.
✓
NOTE!
The default setting of P397 meets most application needs of the inverter. Therefore, avoid modifying
its content without knowing the related consequences. If you are not sure, contact WEG Technical
Assistance before changing P397.
P045 - Fan Enabled Time

11
Properties: ro
Description:
It indicates the total number of hours that the heatsink fan remained connected. This value is kept even when the
inverter is disconnected.
P047 - CONF Status
Properties: ro
Description:
This parameter shows the source situation of the CONFIG mode. The Table 11.3 on page 11-5 describes the
11-4 | CFW300
READ
CONFIG status.
Table 11.3: Situations for CONFIG status
P047 Condition
0 Out of CONFIG status. The HMI and parameters P006 and P680 must not indicate ConF
1 Two or more DIx (P263...P270) programmed for (4 = Forward Run)
2 Two or more DIx (P263...P270) programmed for (5 = Reverse Run)
3 Two or more DIx (P263...P270) programmed for (6 = Start)
4 Two or more DIx (P263...P270) programmed for (7 = Stop)
5 Two or more DIx (P263...P270) programmed for (8 = Direction of Rotation)
6 Two or more DIx (P263...P270) programmed for (9 = LOC/REM)
7 Two or more DIx (P263...P270) programmed for (11 = Accelerate E.P.)
8 Two or more DIx (P263...P270) programmed for (12 = Decelerate E.P.)
9 Two or more DIx (P263...P270) programmed for (14 = 2nd Ramp)
10 Reserved
11 Two or more DIx (P263...P270) programmed for (24 = Disable Flying Start)
12 Two or more DIx (P263...P270) programmed for (26 = Programming Off)
13 Reserved
14 Reserved
15 DIx (P263...P270) programmed for (4 = Forward Run) without DIx (P263...P270) programmed for (5 = Reverse Run) or the
opposite
16 DIx (P263...P270) programmed for (6 = Start) without DIx (P263...P270) programmed for (7 = Stop) or the opposite
17 P221 or P222 programmed for (8 = Multispeed) without DIx (P263...P270) programmed for (13 = Multispeed) or the opposite
18 P221 or P222 programmed for (7 = E.P.) without DIx (P263...P270) programmed for (11 = Accelerate E.P) or the opposite
19 P224 programmed for (1 = DIx) OR P227 programmed for (1 = DIx) without DIx (P263...P270) programmed for (1 = Run/Stop)
AND without DIx (P263...P270) programmed for (2 = General Enable) AND without DIx (P263...P270) programmed for (3 =
Quick Stop) AND without DIx (P263...P270) programmed for (4 = Forward Run) AND without DIx (P263...P270) programmed
for (6 = Start)
20 Reserved
21 P221 or P222 programmed for (8 = Multispeed) with DI1 (P263) AND DI2 (P264) OR DI1 (P263) AND DI5 (P267) OR DI1 (P263)
AND DI6 (P268) OR DI2 (P264) AND DI5 (P267) OR DI2 (P264) AND DI6 (P268) OR DI5 (P267) AND DI6 (P268) programmed
for (13 = Multispeed)
22 Minimum Frequency Reference (P133) greater than Maximum Frequency Reference (P134)
23 to 28 Reserved
29 Two or more DIx (P263...270) programmed for (49 = Enable Fire Mode) OR two or more DOx (P275...P278) Programmed for
(45 = Fire Mode ON) OR P580 programmed for 1, 2 or 4 (Fire Mode Enabled) without DIx programmed for (49 = Enable Fire
Mode) OR DIx programmed for (49 = Enable Fire Mode) OR DOx programmed for (45 = Fire Mode ON) and P580 programmed
for (0 = Fire Mode Disabled) or (3 = Reserved)
30 to 32 Reserved
33 Parameterization in conflict with DC Bus Compensation. Energy Saver active (P588 value other than zero), Controle VVW ativo
(P202 = 5), Functions Ride-Through or Flying Start are enable (P320 value other than zero)
11
CFW300 | 11-5
READ
P680 - Logical Status

Bit 0 = Reserved
Bit 1 = Run Command
Bit 2 = Fire Mode
Bit 5 = 2nd Ramp
Bit 6 = Config. Mode
Bit 7 = Alarm
Bit 8 = Running
Bit 9 = Enabled
Bit 10 = Forward
Bit 11 = JOG
Bit 12 = Remote
Bit 13 = Subvoltage
Bit 14 = Reserved
Bit 15 = Fault
Properties: ro
Description:
The inverter status word is unique for all the sources and can only be accessed for reading. It indicates all the
relevant operating status and modes of the inverter. The function of each bit of P680 is described in Table 11.4 on
page 11-6.
Table 11.4: Status word P680

BIT Function Description
0 Reserved -
0: There was no Run command
1 Run Command
1: There was Run command
0: Fire Mode function inactive
2 Fire Mode
1: Fire Mode function active
3 and 4 Reserved -
0: 1st acceleration and deceleration ramp by P100 and P101
5 2nd Ramp
1: 2nd acceleration and deceleration ramp by P102 and P103
0: inverter operating in normal conditions
6 Config. Status 1: inverter in configuration state. It indicates a special condition in which the inverter cannot be
enabled, because it has parameterization incompatibility
0: inverter is not in alarm state
7 Alarm
1: inverter is in alarm state
0: motor is stopped
8 Running
1: inverter is running according to reference and command
11 9 Enabled
0: inverter is completely disabled
1: inverter is completely enabled and ready to turn the motor
0: motor is running in the reverser direction
10 Forward
1: motor is running in the forward direction
0: JOG function inactive
11 JOG
1: JOG function active
0: inverter in Local mode
12 Remote
1: inverter in Remote mode
0: no undervoltage
13 Undervoltage
1: with undervoltage
14 Reserved -
0: inverter is not in fault state
15 Fault
1: some fault registered by the inverter
11-6 | CFW300
READ
P681 - 13-Bit Speed
Properties: ro
Description:
The 13-bit Frequency Reference is a scale based on the motor rated speed (P402) or on the motor rated frequency
(P403). In the inverter, parameter P403 is taken as the base to determine the frequency reference.
Thus, the 13-bit frequency value has a range of 16 bits with signal, that is, -32768 to 32767; however, the rated
frequency in P403 is equivalent to the value 8192. Therefore, the maximum value in the range 32767 is equivalent
to four times P403:
P681 = 0000h (0 decimal) → motor speed = 0
P681 = 2000h (8192 decimal) → motor speed = rated frequency
P690 - Logic State 2

Bit 2 = DC Link Voltage Extended
Bit 3 = Energy Saver
Bit 4 = Fs Reduction
Bit 5 = Reserved
Bit 6 = Deceleration Ramp
Bit 7 = Acceleration Ramp
Bit 8 = Freeze Ramp
Bit 9 = Setpoint Ok
Bit 10 = DC Link Regulation
Bit 11 = 50 Hz Config
Bit 12 = Ride-Through
Bit 13 = Flying Start
Bit 14 = DC Braking
Bit 15 = PWM pulse
Properties: ro
Description:
Parameter P690 presents other signaling bits for functions implemented in the inverter. The function of each bit of
P0690 is described in Table 11.5 on page 11-8. 11
CFW300 | 11-7
READ
Table 11.5: Status word P690

0 to 1 Reserved -
0: DC Link Voltage Extended inactive
2 DC Link Voltage Extended
1: DC Link Voltage Extended active
0: Energy saving inactive
3 Energy Saving
1: Energy saving active
0: Output frequency reduction inactive
4 Fs Reduction
1: Output frequency reduction active
5 Reserved -
0: No deceleration
6 Deceleration Ramp
1: Inverter accelerating
0: No deceleration
7 Acceleration Ramp
1: Inverter accelerating
0: Ramp operating in normal conditions
8 Frozen Ramp
1: The path of the ramp is frozen by some command source or internal function
0: Output frequency has not reached reference yet
9 Setpoint OK
1: Output frequency reached reference
0: DC Link Regulation inactive
10 DC Link Regulation
1: DC Link Regulation active
0: Factory default loaded in 60 Hz (P204 = 5)
11 50 Hz Config
1: Factory default loaded in 50 Hz (P204 = 6)
0: No execution of Ride-Through
12 Ride-Through
1: Executing Ride-Through
0: No execution of Flying Start
13 Flying Start
1: Executing Flying Start
0: DC breaking inactive
14 DC Braking
1: DC breaking active
0: PWM voltage pulses in the output disabled
15 PWM Pulses
1: PWM voltage pulses in the output enabled
11
11-8 | CFW300
COMMUNICATION
12 COMMUNICATION
In order to exchange information via communication network, the frequency inverter features several standardized
communication protocols, such as Modbus (RTU and TCP), CANopen, DeviceNet, Profibus DP and Ethernet IP.
For further details referring to the inverter configuration to operate in those protocols, refer to the inverter user’s
manual for communication with the desired network.
12.1 COMMANDS AND COMMUNICATION STATUS
See below the parameters related to the states and commands through the communication networks available for
the frequency inverter.
P313 - Action for Communic. Error

1 = Ramp Stop
2 = General Disable
3 = Go to LOC
4 = LOC Keep Enab.
5 = Cause Fault
P682 - Serial/USB Control
P684 - CO/DN/DP/ETH Control

Bit 0 = Ramp Enable
Bit 2 = Run Forward
Bit 3 = JOG Enable
Bit 4 = Remote
Bit 5 = 2nd Ramp
Bit 6 = Reserved
Bit 7 = Fault Reset
Properties: ro
Description:
The inverter control word for a certain source is accessible for reading and writing, but read only access is permitted
for the other sources. The inverter has a common word for each interface, which is defined by the function of its
bits separately as per Table 12.1 on page 12-2. The value of P682 is indicated in hexadecimal.
12
CFW300 | 12-1
COMMUNICATION
Table 12.1: Status word P682/P684

0: stops the motor by deceleration ramp
0 Ramp Enable
1: spins the motor according to the acceleration ramp until reaching the speed reference value
0: disables the inverter completely, interrupting the power supply to the motor
1 General Enable
1: enables the inverter completely, allowing the operation of the motor
0: spins the motor in the opposite direction of the reference signal (reverse)
2 Run Forward
1: spins the motor in the direction of the reference signal (forward)
0: disable JOG function
3 Enable JOG
1: enable JOG function
0: inverter goes into Local mode
4 Remote
1: inverter goes into Remote mode
0: acceleration and deceleration ramp by P100 and P101
5 2nd Ramp
1: acceleration and deceleration ramp by P102 and P103
6 Reserved -
0: no function
7 Fault Reset
1: if in fault state, reset the fault
8 to 15 Reserved -
P683 - Serial/USB Speed Ref.
P685 - CO/DN/DP/ETH Speed Ref
Properties: ro
Description:
It allows programming the motor speed reference via communication interfaces only. For other sources (HMI, etc.),
it behaves as a read-only parameter.
To enable the use of the reference written in this parameter, the product must be programmed to use the speed
reference via communication network. This is programming is done using parameters P221 and P222.
This word uses a 13-bit resolution with signal to represent the motor rated frequency (P403):
P683 = 0000h (0 decimal) → speed reference = 0.

P683 = 2000h (8192 decimal) → speed reference = rated frequency (P403).
P685 = 0000h (0 decimal) → speed reference = 0.

P685 = 2000h (8192 decimal) → speed reference = rated frequency (P403).
12.2 SERIAL
See below the frequency inverter parameters that are directly related to the Modbus RTU communication.
12
P308 - Serial Address

Properties: cfg
12-2 | CFW300
COMMUNICATION
P310 - Serial Baud Rate
Range: 0 = 9600 bits/s Default: 1

1 = 19200 bits/s
2 = 38400 bits/s
3 = 57600 bits/s
4 = 76800 bits/s
Properties: cfg
P311 - Serial Bytes Config.
Range: 0 = 8 bits, no, 1 Default: 1

1 = 8 bits, even,1
2 = 8 bits, odd, 1
3 = 8 bits, no, 2
4 = 8 bits, even,2
5 = 8 bits, odd, 2
Properties: cfg
P312 - Serial Protocol
Range: 0 to 1 = Reserved Default: 2

2 = Modbus RTU Slave
3 = BACnet
4 = Reserved
5 = ModBus RTU Master
Properties: cfg
P314 - Serial Watchdog

Properties: cfg
P316 - Serial Interf. Status
Range: 0 = Inactive Default:

1 = Active
2 = Watchdog Error
Properties: ro
Description: 12
These parameters are used for configuration and operation of the serial interfaces. For a description detailed, refer
to the Modbus RTU, user’s manual, available for download on the website: www.weg.net.
12.3 BLUETOOTH
See below the parameters to configure and operate the Bluetooth interface. For the correct configuration of this
interface, it is necessary to configure properly the parameters of the Section 12.2 SERIAL on page 12-2.
CFW300 | 12-3
COMMUNICATION
P770 - Blueooth Device Name
Range: 0 to 9999 Default: Serial Number of

the Inverter
Description:
This parameter identifies the bluetooth device with a friendly name on the network. This name is limited to the four
digits available on the inverter display.
The default value of this parameter is the last four digits of the inverter serial number.
✓
NOTE!
Parameter P770 is only available with the bluetooth accessory connected.
P771 - Bluetooth Password PIN

Description:
This parameter defines the bluetooth parity password. This password is limited to the four digits available on the
inverter display. It is recommended that the user change this password.
✓
NOTE!
Parameter P771 is only available with the bluetooth accessory connected.
12.4 BACNET
See below the parameters to configure and operate the BACnet communication.
P760 - BACnet Dev Inst Hi
P761 - BACnet Dev Inst Lo
P762 - Max Number of master
12 Range: 0 to 127 Default: 127
P763 - MS/TP Max info Frame
Range: 0 to FFFF (hexa) Default: 1
P764 - I-AM Msg transmition
Range: 0 = Power Up Default: 0

1 = Continuous
12-4 | CFW300
COMMUNICATION
P765 - Token RX Quantity
Properties: ro
Description:
Parameters for configuration and operation of the BACnet communication. For a detailed description, refer to the
BACnet communication manual, available for download on: www.weg.net.
12.5 CANOPEN AND DEVICENET
See below the parameters to configure and operate the CAN interface.
P700 - CAN Protocol
Range: 1 = CANopen Default:

2 = DeviceNet
P701 - CAN Address
P702 - CAN Baud Rate
Range: 0 = 1 Mbps/Auto Default: 0

1 = Reserved/Auto
2 = 500 Kbps
3 = 250 Kbps
4 = 125 Kbps
5 = 100 Kbps/Auto
6 = 50 Kbps/Auto
7 = 20 Kbps/Auto
8 = 10 Kbps/Auto
P703 - Bus Off Reset
Range: 0 = Manual Default: 1

1 = Automatic
12
P705 - CAN Controller Status
Range: 0 = Disabled Default:

1 = Auto-baud
2 = CAN Active
3 = Warning
4 = Error Passive
5 = Bus Off
6 = No Bus Power
Properties: ro
CFW300 | 12-5
COMMUNICATION
P706 - RX CAN Telegrams
Properties: ro
P707 - TX CAN Telegrams
Properties: ro
P708 - Bus Off Counter
Properties: ro
P709 - CAN Lost Messages
Properties: ro
P710 - DeviceNet I/O instances
Range: 0 = ODVA Basic 2W Default: 0

1 = ODVA Extend 2W
2 = Manuf.Spec.2W
3 = Manuf.Spec.3W
4 = Manuf.Spec.4W
5 = Manuf.Spec.5W
6 = Manuf.Spec.6W
P711 - DeviceNet Read Word #3

12
P715 - DeviceNet Write Word #3
12-6 | CFW300
COMMUNICATION
P719 - DeviceNet Network Status
Range: 0 = Offline Default:

1 = OnLine, Not Conn
2 = OnLine, Connect.
3 = Connection Timed out
4 = Link Failure
5 = Auto-Baud
Properties: ro
P720 - DeviceNet Master Status
Range: 0 = Run Default:

1 = Idle
Properties: ro
P721 - CANopen Comm. Status

1 = Reserved
2 = Communic. Enabled
3 = Error Ctrl. Enable
4 = Guarding Error
5 = Heartbeat Error
Properties: ro
P722 - CANopen Node Status

1 = Initialization
2 = Stopped
3 = Operational
4 = Preoperational
Properties: ro
12
Description:
Parameters for configuration and operation of the CAN interface. For detailed description, refer to manual CANopen
communication or DeviceNet communication manual available for download on the website: www.weg.net.
12.6 PROFIBUS DP
See below the parameters to configure and operate the Profibus interface.
CFW300 | 12-7
COMMUNICATION
P740 - Profibus Comm. Status

1 = Access Error
2 = Offline
3 = Config. Error
4 = Param. Error
5 = Clear Mode
6 = Online
Properties: ro
P742 - Profibus Read Word #3
P746 - Profibus Write Word#3
P750 - Profibus Address
P751 - Profibus Teleg. Sel.
Range: 1 = Std. Teleg. 1 Default: 1

2 = Telegram 100
12 3 = Telegram 101
4 = Telegram 102
5 = Telegram 103
12-8 | CFW300
COMMUNICATION
P754 - Profibus Baud Rate
Range: 0 = 9.6 kbit/s Default: 0

1 = 19.2 kbit/s
2 = 93.75 kbit/s
3 = 187.5 kbit/s
4 = 500 kbit/s
5 = Not Detected
6 = 1500 kbit/s
7 = 3000 kbit/s
8 = 6000 kbit/s
9 = 12000 kbit/s
10 = Reserved
11 = 45.45 kbit/s
Description:
Parameters for configuration and operation of the Profibus interface. For a detailed description, refer to the
CANopen communication or DeviceNet communication manual available for download on the website:
www.weg.net.
12.7 ETHERNET
See below the parameters to configure and operate the Ethernet interface.
P850 - IP Address Config
Range: 0 = Parameters Default: 1

1 = DHCP
Properties: cfg
P851 - IP Address 1
P852 - IP Address 2
P853 - IP Address 3
P854 - IP Address 4

Properties: cfg
12
CFW300 | 12-9
COMMUNICATION
P855 - CIDR Sub-net
Range: 0 = Reserved Default: 24

1 = 128.0.0.0
2 = 192.0.0.0
3 = 224.0.0.0
4 = 240.0.0.0
5 = 248.0.0.0
6 = 252.0.0.0
7 = 254.0.0.0
8 = 255.0.0.0
9 = 255.128.0.0
10 = 255.192.0.0
11 = 255.224.0.0
12 = 255.240.0.0
13 = 255.248.0.0
14 = 255.252.0.0
15 = 255.254.0.0
16 = 255.255.0.0
17 = 255.255.128.0
18 = 255.255.192.0
19 = 255.255.224.0
20 = 255.255.240.0
21 = 255.255.248.0
22 = 255.255.252.0
23 = 255.255.254.0
24 = 255.255.255.0
25 = 255.255.255.128
26 = 255.255.255.192
27 = 255.255.255.224
28 = 255.255.255.240
29 = 255.255.255.248
30 = 255.255.255.252
31 = 255.255.255.254
Properties: cfg
P856 - Gateway 1
P857 - Gateway 2
P858 - Gateway 3
12 P859 - Gateway 4

Properties: cfg
12-10 | CFW300
COMMUNICATION
P860 - MBTCP: Communication Status

1 = No connection
2 = Connected
3 = Timeout Error
Properties: ro
P863 - MBTCP: Active Connections
Properties: ro
P865 - MBTCP: TCP Port

Properties: cfg
P868 - MBTCP: Timeout

Properties: cfg
P869 - EIP: Master Status
Range: 0 = Run Default:

1 = Idle
Properties: ro
P870 - EIP: Communication Status

1 = No connection
2 = Connected
3 = Timeout in I/O Connection
4 = Reserved
Properties: ro
P871 - EIP: Data Profile 12
Range: 0 to 3 = Reserved Default: 8

4 = 120/170: CIP Basic Speed + I/O
5 = 121/171: CIP Extended Speed + I/O
6 to 7 = Reserved
8 = 100/150: Manufac. Speed + I/O
9 to 10 = Reserved
Properties: cfg
CFW300 | 12-11
COMMUNICATION
P872 - Ethernet Read Word #3
P880 - Ethernet Write Word #3
P889 - Ethernet Interface Status
Range: 0 to 3 (hexa) Default:

Bit 0 = Link 1
Bit 1 = Link 2
Properties: ro
Description:
Parameters for configuration and operation of the Ethernet interface. For a detailed description, refer to the manual
of Ethernet communication, available for download on: www.weg.net.
12
12-12 | CFW300
SOFTPLC
13 SOFTPLC
The SoftPLC function allows the inverter to assume PLC (Programmable Logical Controller). For further details
regarding the programming of those functions in the inverter, refer to the “Help” menu of the WPS software.
13.1 COMMAND AND STATUS
See below the parameters related to the SoftPLC commands and states.
P900 - SoftPLC Status
Range: 0 = No Application Default:

1 = Installing Application
2 = Incompat. Application
3 = Application Stopped
4 = Application Running
Properties: ro
Description:
It allows the user to view the status in which the SoftPLC is. If there is no application installed, the parameters P910
to P959 will not be shown on the HMI.
If this parameter presents option 2 = Incompat. App., it indicates the user’s program loaded on the SoftPLC is not
compatible with the inverter firmware version.
In this case, it is necessary that the user recompile the project on the WPS, considering the new inverter version
and redo the download.
P901 - SoftPLC Command
Range: 0 = Stop Application Default: 0

1 = Run Application
Description:
This parameter allows stopping, running or excluding an application installed, but to do so, the motor must be
disabled.
P902 - Scan Cycle Time
Range: 0.000 to 9.999 s Default:
Properties: ro
Description:
This parameter sets the application scanning time. The larger the application, the longer is the scanning time.
P903 - SoftPLC Appl. 13
Range: 0 = User Default: 1

1 = PID Controller
Properties: cfg
Description:
It allows the user to select the application to be executed, according to Table 13.1 on page 13-2.
CFW300 | 13-1
SOFTPLC
Table 13.1: Description of the parameter P903 options

P903 Description
0 It defines that the application that will run on the SoftPLC is the one loaded by the user through the ladder programming tool
1 It defines that the application that will run on the SoftPLC is the PID controller
WARNING!
! It is recommended to load the factory setting (P204 = 5 or 6) after alternating between user’s
application and PID controller application.
P904 - Action for SoftPLC Application not Running
Range: 0 = Disabled Default: 0

1 = Cause Alarm (A708)
2 = Cause Fault (F709)
Description:
It defines which action will be taken by the product in case the SoftPLC not running condition is detected, and it
may generate alarm A708 (1), fault F709 (2) or neither of the previous actions, remaining inactive (0).
13.2 USER
See below the SoftPLC user’s parameters.
P910 - SoftPLC Parameter 1
13 P919 - SoftPLC Parameter 10
13-2 | CFW300
SOFTPLC

13
CFW300 | 13-3
SOFTPLC
Range: -9999 to 9999 Default: 0

Description:
These are parameters whose use is defined by the SoftPLC function.
✓
NOTE!
Parameters P910 to P959 can only be viewed when there are application installed.
13
13-4 | CFW300
APPLICATIONS
14 APPLICATIONS
Using the SoftPLC function of the inverter, it is possible to develop an application (or functionality) in ladder language
and include it in the inverter software.
Parameter P903 allows selecting the application and uploading it to the SoftPLC execution area of the inverter.
The frequency inverter has the following application already implanted:
PID Controller.
14.1 PID CONTROLLER
The PID controller application can be used to control a process in closed loop. This application adds a proportional,
integral and derivative controller superimposed to the regular speed control of the frequency inverter having selection
options:
Control setpoint source.
Process variable source.
Operation mode in manual or automatic mode.
Alarms by low or high process variable level.
Configuration of the control action in direct or reverse mode.
Setting the conditions to activate the sleep and wake up mode.
Basically, the PID controller application compares the control setpoint to the process variable and controls the
motor speed to try to eliminate any errors so as to keep the process variable equal to the control setpoint required
by the user. The setting of the gains P, I and D determine the speed at which the inverter will respond to eliminate
that error. See the PID controller block diagram below.
Control Filter for control Control PID Operation

setpoint setpoint action via controller mode via
AI1
P928 P929 Speed
AI2
P911 P911 P917 reference
P912 0.0 % (P133) to
P913 100.0 % (P134)
P914 P918
P915 P935 P931, P932
Selection via P933, P934
P920
Process variable
AI1
P916
AI2
AI1 - AI2
Selection
via P921 P922, P923
Figure 14.1: PID controller block diagram
Application examples of the PID controller:
Flow or pressure control in a pipe system.
Temperature of a furnace or oven. 14

Dosing of chemicals in tanks.
The example below defines the terms used by the PID controller application.
CFW300 | 14-1
APPLICATIONS
An electric pump used in a water pumping system in which the pressure must be controlled at the pump output pipe.
A pressure transducer is installed on the pipe and provides an analog feedback signal to the inverter proportional to
the water pressure. That signal is called process variable and can be viewed in parameter P916. A control setpoint
is programmed in the inverter via HMI (P911), or via analog input (AI1 or AI2), or via electronic potentiometer
function (DI3 and DI4), or via logical combination of digital inputs DI3 and DI4 according to the control setpoint
source defined in P920. The control setpoint is the water pressure which the pump must produce regardless of
the demand variations in the pump output at any moment.
In order to enable the operation of the PID controller application, it is necessary to program the speed reference
for the SoftPLC function, that is, parameter P221 or P222 in 12 = SoftPLC, and select the PID controller control
action in P928 for direct action (=1) or reverse action (=2), thus enabling the PID operation. Otherwise, the alarm
message “A790: Speed reference source (P221 or P222) not programmed for the SoftPLC (12)” will be generated.
The functionalities that can be programmed in the analog and digital inputs and outputs are shown in the Table
14.1 on page 14-2.
Table 14.1: Functionalities and programming of the analog and digital inputs and outputs
Analog Inputs AI1 (P231) and AI2 (P236)
Control Setpoint = 16
Process Variable = 17
Analog Outputs AO1 (P251) and AO2 (P254)
Control Setpoint = 29
Process Variable = 30
Digital Inputs DI2 (P264) to DI4 (P266)
Manual / Automatic PID (DI2) = 51
Increase Setpoint Command (PE) (DI3) = 52
Decrease Setpoint Command (PE) (DI4) = 53
1st DI of the Control Setpoint (DI3) = 54
2nd DI of the Control Setpoint (DI4) = 55
Digital Outputs DO1 (P275) to DO4 (P278)
Process Variable Low Level (A760/F761) = 46
Process Variable High Level (A762/F763) = 47
The control setpoint source of the PID controller is defined in parameter P920, and it may be: via parameter P911,
which can be changed via HMI (or communication networks); via analog input AI1 or AI2, being parameter P231
(AI1) or P236 (AI2) previously programmed to 16 = Control Setpoint so that it is enabled for operation; via Electronic
Potentiometer (EP) through increase and decrease commands in digital inputs DI3 and DI4, being parameter P265
(DI3) previously programmed to 51 = Increase Setpoint Command (EP) and P266 (DI4) to 52 = Decrease Setpoint
Command (EP); via logical combination of digital inputs, with the selection of up to four control setpoints, being
parameter P265 (DI3) previously programmed to 53 = 1st DI for Control Setpoint and P266 (DI4) to 54 = 2nd DI for
Control Setpoint.
The value of the present control setpoint of the PID controller (P911) can be indicated via analog output AO1 or
AO2, being necessary to program P251 (AO1) or P254 (AO2) to 29 = Control Setpoint. The variable full scale is
100.0 % and corresponds to 10 V or 20 mA.
The source of the PID controller process variable is defined in parameter P921, and it can be via analog input AI1
and/or AI2, being then parameter P231 (AI1) and/or P236 (AI2) previously programmed to 17 = Process Variable.
The value of the PID controller process variable (P916) can be indicated via analog output AO1 or AO2, being
necessary to program P251 (AO1) or P254 (AO2) to 30 = Process Variable. The variable full scale is 100.0 % and
corresponds to 10 V or 20 mA.
The PID controller operation mode is defined in parameter P929, which can be manual, always automatic or via a
Manual/Automatic command through digital input DI2, being then parameter P264 (DI2) previously programmed
to 50 = Man/Auto PID Selection. Digital input DI2 programmed to PID in Manual/Automatic is active while it is at
logical level “1”, indicating automatic command, and inactive at logical level “0”, indicating manual command.
14
Digital outputs DO1 to DO4 can be programmed to indicated alarm/fault conditions for low level or high level of the
process variable (PV), seeing that one of the respective parameters (P275 to P278) must be programmed to 46 =
Process Variable Low Level (equivalent to PV<PVy) or 47 = Process Variable High Level (equivalent to PV>PVx).
14-2 | CFW300
APPLICATIONS
14.1.1 Start-Up
See below the required steps to put the PID controller application into operation.
✓
NOTE!
For the PID controller application to work properly, it essential to check if the inverter is configured
properly to drive the motor at the desired speed. In order to do so, check the following settings:
Acceleration and deceleration ramps (P100 to P101).
Current limit (P135) for V/f and VVW control modes.
Torque boost (P136 and P137) and slip compensation (P138) if in the V/f control mode.
Configuring the PID Controller Application The PID controller application will be configured according to the
example shown below, where:
The frequency inverter will be configured to operate in the local mode.
Digital input DI1 will be used for the Run/Stop command in local mode.
Digital input DI2 will be used to select the PID to Manual/Automatic.
The PID controller process variable (PV) will be connected to analog input AI1 in the scale of 4-20 mA, where 4
mA is equal to 0 bar and 20 mA is equal to 4.0 bar.
The PID controller control setpoint (SP) will be via HMI (keys).
Pressure
Fuses Transducer
Line
DI1 - run / stop

Isolating switch DI2 - manual / automatic PID
Frequency
inverter
Process
Shield
Figure 14.2: Example of the PID controller application
14
CFW300 | 14-3
APPLICATIONS
Table 14.2: Programming sequence of the PID controller application

Indication on the
Seq. Action / Result
Display
1 It selects the PID controller application in the SoftPLC function of the inverter P903 = 1
2 It enables the execution of the PID controller application P901 = 1
It selects the PID controller control action, thus enabling its operation and uploading, at this moment
3 P928 = 1
the application default setting (which is indicated below) to the frequency inverter. 1 = Direct
4 Acceleration time in seconds P100 = 2.5 s
5 Deceleration time in seconds P101 = 2.5 s
6 Minimum frequency P133 = 40.0 Hz
7 Maximum frequency P134 = 60.0 Hz
It selects the parameter of the HMI main display to show the value of the PID controller process variable
8 P205 = 916
This setting is optional
It selects the HMI bar graph parameter to show the present motor speed.
9 P207 = 002
This setting is optional
10 Full scale of the Speed Reference P208 = 600
11 Engineering unit of the Speed Reference P209 = 3
12 Speed Reference indication form P210 = 1
13 Full scale of the HMI bar graph P213 = 600
14 LOC/REM Source Selection. 0 = Always Local P220 = 0
15 Selection of the Reference in Local mode. 12 = SoftPLC P221 = 12
16 Selection of the Run/Stop Command in Local mode. 1 = DIx P224 = 1
17 AI1 Signal Function. 17 = Process Variable (PV) P231 = 17
18 AI1 Gain P232 = 1.000
19 AI1 Signal. 0 = 0 to 10 V / 20 mA P233 = 0
20 Offset AI1 P234 = 0.00 %
21 Filter AI1 P235 = 0.25 s
22 Digital input DI1 is used for the motor run or stop command. 1 = run/stop P263 = 1
23 Digital input DI2 is used to set the PID to Automatic or Manual. 50 = PID Man / Auto P264 = 50
SoftPLC Engineering Unit. 0 = none. The sensor of the process variable is in bar, and this
24 P510 = 0
variable is not available on the inverter
25 Indication form of the SoftPLC engineering unit. 2 = wx.yz P511 = 2
26 It selects the PID controller operation mode. 2 = manual/automatic via DI2 P929 = 2
27 It selects the automatic setting mode of the control setpoint. 0 = P911 inactive and P918 inactive P930 = 0
28 The PID controller Setpoint will be set via HMI. 0 = via HMI P920 = 0
29 The PID Process Variable will be read via analog input AI1. 1 = via AI1 P921 = 1
The range of the sensor connected to analog input AI1 is 0 to 4.0 bar. Program this parameter for
30 P922 = 0.00
the minimum sensor value, which is the minimum of the analog input 4 mA
The range of the sensor connected to analog input AI1 is 0 to 4.0 bar. Program this parameter for
31 P923 = 4.00
the maximum sensor value, which is the maximum of the analog input 20 mA
32 Setting of the control Setpoint via HMI P911 = 2.00
33 Control Setpoint Filter P935 = 0.150 s
34 PID controller Sampling Period P934 = 0.100 s
35 Proportional Gain of the PID controller P931 = 1.00
36 Integral Gain of the PID controller P932 = 5.00
37 Derivative Gain of the PID controller P933 = 0.00
Parameters P931, P932, P933 and P934 must be set according to the response of the process to be controlled.
See below suggestions for initial values of sampling time and gain setting for the PID controller according to the
process to be controlled.
Table 14.3: Suggestions for the PID controller gain settings

Sampling Time Gains
Quantity
P934 Proportional P931 Integral P932 Derivative P933
Pressure in pneumatic system 0.10 s 1.00 5.00 0.00
Flow in pneumatic system 0.10 s 1,00 5.00 0.00
14 Pressure in hydraulic system 0,10 s 1.00 5.00 0.00
Flow in hydraulic system 0.10 s 1,00 5.00 0.00
Temperature 0.50 s 2.00 0.50 0.10
14-4 | CFW300
APPLICATIONS
Putting into Operation Check the state of the PID controller application in parameter P900. Value equal to 4
indicates the application is already in operation. Value equal to 3 indicates the application is stopped; therefore, it
is necessary to change the command value for the SoftPLC in parameter P901 to 1 (execute application). Value
different from 3 or 4 indicates the application cannot go into operation. For further details, refer to the inverter
SoftPLC manual.
1. Manual Operation (DI2 open): keeping DI2 open (Manual), check the indication of the process variable on the
HMI (P916) based on an external measurement of the sensor signal (transducer) in analog input AI1.
Then, changes the manual setpoint value of the PID controller (P918) until reaching the desired process
variable value. Check if the control setpoint value (P911) is set to this value, and then put the PID controller
into the automatic mode.
✓
NOTE!
The PID controller only begins the speed regulation when the motor reaches the minimum speed
programmed in P133, as it was configured to operate from 0.0 to 100.0 %, where 0.0 %
corresponds to the minimum speed programmed in P133, and 100.0 % corresponds to the
maximum speed programmed in P134.
2. Automatic Operation (DI2 closed): close DI2 and make the dynamic adjustment of the PID controller, that
is, of the proportional (P931), integral (P932) and derivative (P933) gains, checking if the regulation is being
done correctly. In order to do so, just compare the control setpoint and the process variable and check if the
values are close. Also check how fast the motor responds to the oscillations of the process variable.
It is important to point out that the setting of the PID controller gains is a step that requires some attempt
and error procedure to reach the desired response time. If the system responds quickly and oscillates close
to the control setpoint, then the proportional gain is too high. If the system responds slowly and it takes a
long time to reach the control setpoint, the proportional gain is too low and must be increased. In case the
process variable does not reach the required value (control setpoint), the integral gain must be set then.
14.1.2 Academic PID Controller
The PID controller implemented on the inverter is academic. See below the equations that characterize the
Academic PID controller, which is the base of this function algorithm.
The transfer function in the frequency domain of the Academic PID controller is:
[ ]
1
y(s) = Kp x e(s) x 1 + + sTd
sTi
Replacing the integrator by a sum and the derivative by the incremental quotient, we obtain the approximation for
the discrete (recursive) transfer equation presented below:
[ ]
y(k) = i(k − 1) + Kp (1 + Ki Ta + Kd /Ta )e(k) − (Kd /T a)E(k − 1) x 10
Where:
y(k): present output of the PID controller; it may vary from 0.0 to 100.0 %.
i(k-1): integral value in the previous state of the PID controller.
Kp : Proportional gain = P931.
Ki : Integral gain = P932 = [1 / Ti (s)].
Kd : Differential gain = P933 = [Td (s)].
Ta : sampling period of the PID controller = P934.
e(k): present error, being [SP(k) - PV(k)] for direct action, and [PV(k)] - SP(k)] for reverse action.
e(k-1): previous error, being [SP(k-1) - PV(k-1)] for direct action, and [PV(k-1)] - SP(k-1)] for reverse action.
SP: present control setpoint of the PID controller.
PV: process variable of the PID controller, read through the analog inputs (AI1 and AI2).
14
14.1.3 Parameters
See below the description of the parameters related to the PID controller application.
CFW300 | 14-5
APPLICATIONS
P910 - PID Controller Application Version
Properties: ro
Description:
Read-only parameter which presents the software version of the PID controller application developed for the
SoftPLC function of frequency inverter.
P911 - Control Setpoint
Range: -99.99 to 99.99 Default: 2.00

Description:
This parameter defines the setpoint value in automatic mode for the PID controller in engineering unit when the
control setpoint source is programmed to be via HMI or communication networks (P920 = 0). When the control
setpoint source is programmed for some other source (P920 ≠ 0), this parameter will show the present setpoint in
automatic mode for the PID controller.
✓
NOTE!
This parameter will be viewed according to the selection of the parameters for the SoftPLC engineering
unit (P510 and P511).
P912 - Control Setpoint 1
Range: -99.99 to 99.99 Default: 2.00

Description:
These parameters define the setpoint value in automatic mode of the PID controller in engineering unit when the
control setpoint source is programmed to be via logical combination of digital inputs DI3 and DI4 (P950 = 4, 5 or
6) according to Table 14.6 on page 14-9.
✓
NOTE!
These parameters will be viewed according to the selection of the parameters for the SoftPLC
engineering unit (P510 and P511).
P916 - Control Process Variable
Range: -99.99 to 99.99 Default:

14
Properties: ro
Description:
Read-only parameter which presents the value of the PID controller process variable according to the source defined
14-6 | CFW300
APPLICATIONS
in P921 and scale defined in P922 and P923.
✓
NOTE!
The conversion of the value read by the analog input in percentage into the value of the process variable shown in
P916 according to the scale is done through the following formula:
P916 = [ValorAI(%) x (P923 - P922)] + [P922]
P917 - PID Controller Output
Properties: ro
Description:
Read-only parameter which presents, in percentage (%), the value of the PID controller output, where 0.0 %
corresponds to the motor minimum speed (P133), and 100.0 % corresponds to the motor maximum speed
(P134).
P918 - PID Controller Setpoint in Manual Mode

Description:
This parameter defines the value of the PID controller output when it is in the manual mode, that is, when the PID
controller works in manual mode, the value defined as manual setpoint is transferred directly to the PID controller
output.
P919 - PID Controller Logical Status

Bit 0 = Sleep Mode Active (A750)
Bit 1 = PID in Manual (0) / Automatic (1)
Bit 2 = PV Low Level (A760)
Bit 3 = PV Low Level (F761)
Bit 4 = PV High Level (A762)
Bit 5 = PV High Level (F763)
Properties: ro
Description:
This parameter allows monitoring the logical status of the PID controller application. Each bit represents a state.
Table 14.4: Description of the logical status of the PID controller application
Bits 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Process Process Process Process PID controller
Variable High Variable High Variable Low Variable Low in Manual Sleep Mode
Function
Level Level Level Level or Active (A750)
(F763) (A762) (F761) (A760) Automatic 14
CFW300 | 14-7
APPLICATIONS
Bits Values
Bit 0 0: Inverter is not in the alarm condition
Sleep Mode Active (A750) 1: It indicates that the PID controller is in the sleep mode (A750)
Bit 1 0: PID controller operating in Manual mode
PID Controller in Manual or Automatic 1: PID controller operating in Automatic mode
Control Process Variable Low (A760) 1: It indicates that the control process variable (P916) is in low level (A760)
Bit 3 0: Inverter is not in the fault condition
Fault for Control Process Variable Low 1: It indicates that the inverter switched the motor off due to the control
Level (F761) variable low level (F761)
Control Process Variable High Level (A762) 1: It indicates that the control process variable (P916) is in high level (A762)
Bit 5 0: Inverter is not in the fault condition
Fault for Control Process Variable High Level 1: It indicates that the inverter switched the motor off due to the control process
(F763) variable high level (F763)
Bit 6
Reserved
Reserved
Bit 7
Reserved
Reserved
Bit 8
Reserved
Reserved
Bit 9
Reserved
Reserved
Bit 10
Reserved
Reserved
Bit 11
Reserved
Reserved
Bit 12
Reserved
Reserved
Bit 13
Reserved
Reserved
Bit 14
Reserved
Reserved
Bit 15
Reserved
Reserved
P920 - Selection of the Control Setpoint Source
Range: 0 = Control Setpoint via HMI or Communication Default: 0

Networks (P911)
1 = Control Setpoint via Analog Input AI1
2 = Control Setpoint via Analog Input AI2
3 = Control Setpoint via Electronic Potentiometer (EP)
4 = Two Setpoints via Digital Input DI3 (P912 and
P913)
5 = Three Setpoints via Digital Inputs DI3 and DI4
(P912, P913 and P914)
6 = Four Setpoints via Digital Inputs DI3 and DI4 (P912,
P913, P914 and P915)
Properties: cfg
Description:
14
This parameter defines the control setpoint source in automatic mode of the PID controller.
14-8 | CFW300
APPLICATIONS
Table 14.5: Description of the control setpoint source

P920 Description
It defines that the control setpoint source in automatic mode of the PID controller will be the value programmed in parameter P911
0
via HMI of the frequency inverter or written via communication networks
It defines that the control setpoint source in automatic mode of the PID controller will be the value read by the analog input AI1.
1
The value is converted according to the engineering unit 1 and viewed in parameter P911
It defines that the control setpoint source in automatic mode of the PID controller will be the value read by the analog input AI2.
2
The values is converted according to the engineering unit 1 and viewed in parameter P911
It defines that the control setpoint source in automatic mode of the PID controller will be the value defined through the electronic
3 potentiometer function via the Increase Setpoint (DI3) and Decrease Setpoint (DI4) commands. The value of the count is
stored in parameter P911
It defines that there will be two control setpoints in automatic mode of the PID controller selected via logical combination of
4
digital input DI3. The selected control setpoint value is viewed in parameter P911
It defines that there will be three control setpoints in automatic mode of the PID controller selected via logical combination of
5
digital inputs DI3 and DI4. The selected control setpoint value is viewed in parameter P911
It defines that there will be four control setpoints in automatic mode of the PID controller selected via logical combination of
6
digital inputs DI3 and DI4. The selected control setpoint value is viewed in parameter P911
When the control setpoint is via Electronic Potentiometer (EP) function (P920 = 3), the control setpoint of the PID
controller is adjusted by means of digital inputs DI3 and DI4, being DI3 to increase it and DI4 to decrease it.
Figure 14.3 on page 14-9 shows the operation of the EP function: when digital input DI3 is activated, the control
setpoint value (P911) is incremented, and when digital input DI4 is activated, the control setpoint value (P911) is
decremented. In case both digital inputs are activated at the same time, the value remains the same.
DI3 - increase SP
Ramp for
P911 - (control setpoint)
setpoint
DI4 - decrease SP
P911 - (control setpoint)
Active Time
DI3 - increase SP Inactive
Active Time
DI4 - decrease SP Inactive

Time
Sleep
Motor running (RUN) (A750)
Time
Figure 14.3: PID controller block diagram
When the control setpoint is via logical combination of digital inputs DI3 and DI4 (P920 = 4, 5 or 6), the following
truth table must be used so as to obtain the control setpoint of the PID controller in automatic mode.
Table 14.6: Truth table for the control setpoint via logical combination of digital inputs DI3 and DI4
P912 - Control P913 - Control P914 - Control P915 - Control
Setpoint 1 Setpoint 2 Setpoint 3 Setpoint 4
Digital input DI3 0 1 0 1
Digital input DI4 0 0 1 1
14
CFW300 | 14-9
APPLICATIONS
P921 - Selection of the Control Process Variable Source
Range: 1 = Control Process Variable via Analog Input AI1 Default: 1

2 = Control Process Variable via Analog Input AI2
3 = Control Process Variable via Difference between
Analog Input AI1 and AI2
Properties: cfg
Description:
This parameter defines the source of the PID controller process variable.
Table 14.7: Description of the source of the PID controller process variable
P921 Description
1 It defines that the control variable source will be the value read by AI1 and viewed in parameter P916
2 It defines that the control variable source will be the value read by AI2 and viewed in parameter
It defines that the control variable source will be the value read by AI1 minus the value read by AI2
3
that is, the difference between AI1 and AI2, and viewed in parameter P916
P922 - Minimum Sensor Level of the Control Process Variable
Range: -99.99 to 99.99 Default: 0.00

Description:
This parameter defines the minimum value of the sensor connected to the analog input configured for the PID
controller process variable according to its engineering unit.
✓
NOTE!
P923 - Maximum Sensor Level of the Control Process Variable
Range: -99.99 to 99.99 Default: 4.00

Description:
This parameter defines the maximum value of the sensor connected to the analog input configured for the PID
controller process variable according to its engineering unit.
✓
NOTE!
P924 - Value for Low Level Alarm for the Control Process Variable
Range: -99.99 to 99.99 Default: 1.00

Description:
14
This parameter defines the value below which the low level alarm will be generated for the control process variable
(A760).
14-10 | CFW300
APPLICATIONS
✓
NOTE!
Setting it to ”0” disables the low level alarm and fault for the control process variable.
✓
NOTE!
P925 - Time for Low Level Fault for the Control Process Variable

Description:
This parameter defines how long the low level alarm condition should remain so that the control process variable
(A760) will generate fault “F761: Low Level Fault of the Control Process Variable”.
✓
NOTE!
Setting it to “0.0 s” disables the low level fault for the control process variable.
P926 - Value for High Level Alarm for the Control Process Variable
Range: -99.99 to 99.99 Default: 3.50

Description:
This parameter defines the value above which the high level alarm will be generated for the control process variable
(A762).
✓
NOTE!
Setting it to ”0” disables the high level alarm and fault for the control process variable.
✓
NOTE!
P927 - Time for High Level Fault for the Control Process Variable

Description:
This parameter defines how long the high level alarm condition should remain so that the control process variable
(A762) will generate fault “F763: High Level Fault of the Control Process Variable”.
✓
NOTE!
Setting it to “0.0 s” disables the high level fault for the control process variable.
14
CFW300 | 14-11
APPLICATIONS
P928 - Selection of the PID Controller Control Action
Range: 0 = Disable PID Controller Default: 0

1 = Enable PID Controller in Direct Mode
2 = Enable PID Controller in Reverse Mode
Properties: cfg
Description:
This parameter enables the PID controller and defines how the control action will be.
Table 14.8: Description of the PID controller control action

P928 Description
0 It defines that the PID controller will be disabled
It defines that the PID controller will be enabled, and the regulation or control action will be in direct mode. In other words, the
1
error will be the control setpoint value (P911) minus the control process variable value (P916)
It defines that the PID controller will be enabled, and the regulation or control action will be in reverse mode. In other words, the
2
error will be the control process variable value (P916) minus the control setpoint value (P911)
✓
NOTE!
When enabling the PID controller, that is, changing the content of parameter P928 from 0 to 1 or
2 (with application running), the following parameters related to the PID controller application will be
loaded: P100, P101, P133, P134, P205, P207, P208, P209, P210, P213, P220, P221, P224, P231,
P232, P233, P234, P235, P263, P264, P510, P511, P911, P912, P913, P914, P915, P918, P920,
P921, P922, P923, P924, P925, P926, P927, P929, P930, P931, P932, P933, P934, P935, P936,
P937, P938, P939.
✓
NOTE!
The control action of the PID controller must be selected for direct mode when it is necessary to
increase the PID controller output in order to increase the process variable value. E.g.: Pump driven
by an inverter and filling a tank. For the level of the tank (process variable) to increase, it is necessary
that the flow increase, which is accomplished by increasing the speed of the motor.
The control action of the PID controller must be selected for reverse mode when it is necessary to
decrease the PID controller output in order to increase the process variable value. E.g.: Fan driven by
inverter cooling a refrigeration tower. When an increase in temperature is desired (process variable),
it is necessary to reduce the ventilation by reducing the motor speed.
P929 - PID Controller Operation Mode
Range: 0 = Manual Default: 2

1 = Automatic
2 = Select Control to Manual (0) or Automatic (1) via
digital input DI2
Description:
This parameter defines the operation mode of the inverter PID controller.
14
14-12 | CFW300
APPLICATIONS
Table 14.9: Description of the PID controller operation mode

P929 Description
It defines that the PID controller will always operate in manual mode. In other words, the process variable will not be controlled
0 according to the control setpoint required by the user, and the PID controller output value will be the setpoint value in manual
mode programmed in parameter P918
It defines that the PID controller will operate in automatic mode, that is, the process variable will be controlled according to the
1
control setpoint required by the user and the PID controller output value will behave according to the settings defined by the user
It defines the PID controller will be able to operate in manual or automatic mode according to the state of digital input DI2. In other
2 words, if the digital input is in logical level “0”, the PID controller will operate in manual mode; if the digital input is in logical level
“1”, the PID controller will operate in automatic mode
✓
NOTE!
The change from an operation mode to another with the motor running may cause disturbances
on the system control. That can be optimized according to the automatic adjustment mode of the
PID controller setpoint defined in parameter P930 together with the bumpless transfer characteristic
from the manual mode to the automatic mode of the PID block of the SoftPLC function. Bumpless
transfer is merely making the transfer from the manual mode to the automatic mode without causing
variation in the PID controller output. In other words, when the transition from the manual mode to the
automatic mode occurs, the PID controller output value in manual mode is used to start the integral
part of the PID controller in automatic mode. That ensures that the output will start from this value.
P930 - Automatic Adjustment of the PID Controller Setpoint
Range: 0 = P911 inactive and P918 inactive Default: 0

1 = P911 active and P918 inactive
2 = P911 inactive and P918 active
3 = P911 active and P918 active
Description:
This parameter defines if the PID controller setpoint in automatic mode (P911) and/or in manual mode (P918) will
be automatically changed or adjusted when the PID controller operation mode changes.
Table 14.10: Description of the PID controller setpoint automatic adjustment

P930 Description
It defines that, in the transition of the PID controller operation mode from manual to automatic, the control setpoint value (P911)
will not be uploaded with the present value of the control process variable (P916), and, in the transition of the PID controller
0
operation mode from automatic to manual, the setpoint value of the PID controller in manual mode (P918) will not be
uploaded with the present value of the motor speed (P002)
will be uploaded with the present value of the control process variable (P916), and, in the transition of the PID controller operation
1
mode from automatic to manual, the setpoint value of the PID controller in manual mode (P918) will not be
uploaded with the present value of the motor speed (P002)
will not be uploaded with the present value of the control process variable (P916), and , in the transition of the PID controller
2
operation mode from automatic to manual, the setpoint value of the PID controller in manual mode (P918) will be uploaded
with the present value of the motor speed (P002)
will be uploaded with the present value of the control process variable (P916), and , in the transition of the PID controller
3
operation mode from automatic to manual, the setpoint value of the PID controller in manual mode (P918) will be uploaded
with the present value of the motor speed (P002)
✓
NOTE!
The adjustment of the control setpoint in automatic mode is only valid when the control setpoint
14
source is HMI or communication networks (P920 = 0) or via the Electronic Potentiometer Function
(P920 = 3). For other control setpoint sources, the automatic adjustment is not executed.
CFW300 | 14-13
APPLICATIONS
P931 - Proportional Gain
P932 - Integral Gain
P933 - Derivative Gain
Range: 0.00 to 99.99 Default: 1.00

Description:
These parameters define the gains of the PID controller and must be set according to the magnitude or process
that is being controlled.
✓
NOTE!
Table 14.3 on page 14-4 suggests setting values for the gains according to the process to be
controlled by the PID controller.
P934 - PID Controller Sampling Period

Properties: cfg
Description:
This parameter defines the sampling time of the PID controller.
✓
NOTE!
Table 14.3 on page 14-4 suggests setting values for the sampling time according to the process to
be controlled by the PID controller.
P935 - Filter for the PID Controller Control Setpoint

Description:
This parameter configures the time constant of the 1st order filter to be applied to the PID controller control setpoint,
and it is intended to reduce sudden changes in the control setpoint value of the PID controller.
14.1.4 Sleep Mode
This parameter group allows the user to set the operation conditions of the sleep mode.
Sleep Mode is a controlled system state in which the control demand is zero or almost zero, and, at this moment,
the motor driven by the frequency inverter may be switched off. That prevents the motor from running at a low
speed, doing little or nothing for the controlled system. Even if the motor is apparently OFF, the process variable
continues to be monitored so that, when necessary, the controlled system can start the motor again according to
the conditions of the wake up mode.
Wake Up Mode switches on the motor when the difference between the control process variable and the control
setpoint is greater than a certain programmed value.
14
✓
NOTE!
The sleep mode only actuates if the PID controller is enabled and in the automatic mode.
14-14 | CFW300
APPLICATIONS
DANGER!
! When the inverter is in the sleep mode, the motor may spin at any moment because of the process
conditions. If you wish to handle the motor or execute any kind of maintenance, power down the
inverter.
P936 - Deviation of the Control Process Variable to Wake Up
Range: -99.99 to 99.99 Default: 0.30

Description:
This parameter defines the value to be subtracted from (direct PID) or added to (reverse PID) the control setpoint to
start the motor and return to the system control. This value is compared to the control process variable, and, if the
control process variable value is smaller (direct PID) or greater (reverse PID) than this value, the wake up condition
is enabled.
✓
NOTE!
P937 - Time to Wake Up

Description:
This parameter defines the time the wake up mode active condition should remain to start the motor and control
the system. The control process variable must remain smaller (direct PID) or greater (reverse PID) than the deviation
defined in P936 for the time set in P937 for the motor to be started and its speed controlled. In case the wake up
condition (P937) remains inactive for some time, the timer is reset and the time count is restarted.
✓
NOTE!
If, in the energization of the inverter, the “Run/Stop” command is active and the condition to Wake
Up is active, the time programmed in P937 will not be waited for, and thus the motor will be started
instantly.
P938 - Motor Speed to activate the Sleep Mode

Description:
This parameter defines the motor speed value below which the motor will be switched off and go into the sleep
mode.
✓
NOTE!
Setting it to “0.0 Hz” disables the sleep mode; that means the motor will be switched on or off
according to the state of the “Run/Stop” command.
14
P939 - Time to activate de Sleep Mode

CFW300 | 14-15
APPLICATIONS
Description:
This parameter defines the time the motor speed should remain below the value set in P938 for the motor to be
switched off and go into the sleep mode.
✓
NOTE!
The alarm message “A750: Sleep Mode Active” will be shown on the HMI of the frequency inverter
warning that the motor is in the sleep mode.
Figure 14.4 on page 14-16 shows an analysis of the PID controller operation programmed with control action in
direct mode and configured for the Sleep Mode.
COMANDS - DIGITAL INPUTS

DI1 - run/stop
PROCESS VARIABLE
P911 - control setpoint

P936 - process variable deviation to wake up
P937 - time to wake up
MOTOR SPEED (Hz)

P134 - maximum speed reference
P939 - time to activate

the sleep mode
P938 - motor speed to activate the sleep mode
P133 - minimum speed reference
Figure 14.4: Operation of the PID controller with the sleep mode enabled
1. The Run/Stop command via digital input DI1 enables the starting of the motor. As the wake up condition was
not detected, it remains in sleep mode, and the motor remains stopped.
2. The process variable starts to decrease and becomes smaller than the deviation of the process variable
programmed to wake up (P936); at this moment, the time count to wake up (P937) begins.
3. The process variable remains smaller than the process variable deviation to wake up (P936), and the time to
wake up (P937) elapses; at this moment, the command to start the motor and control the system with its
speed variation is executed.
4. The inverter accelerates the motor up to the minimum speed (P133). After that, the PID controller is enabled
and starts controlling the motor speed.
5. Then it is possible to control the process variable so that it reaches the control setpoint required by the user.
To that end, the PID controller output is incremented, making the motor speed increase until reaching the
control stabilization.
14 6. The value of the process variable remains above the required control setpoint due to a decrease in demand,
and the motor speed starts slowing down.
7. The value of the motor speed falls below the value to sleep (P938); the time count to activate the sleep mode
(P939) begins.
14-16 | CFW300
APPLICATIONS
8. The motor speed remains below the value to sleep (P938), and the time to activate the sleep mode (P939)
elapses; at this moment, the command to switch off the motor is executed.
9. The motor is decelerated down to 0 Hz and remains stopped; at this moment the PID controller goes into the
sleep mode.
14
CFW300 | 14-17
APPLICATIONS
14
14-18 | CFW300
APPLICATION EXAMPLES
15 APPLICATION EXAMPLES
This chapter presents typical application examples.
15.1 ANALOG INPUT APPLICATIONS
In this section some applications that use analog inputs are shown. Figure 15.1 on page 15-1 presents some
possible connections. The applications described here require load factory settings (P204 = 5 or 6) for correct
execution.
Frequency Frequency Frequency

inverter inverter inverter
AIx (V)
or
AIx (mA) GND 10 V AIx (V) GND
Transducer Extern
Voltage or Current potentiometer
Electronic Potentiometer
plugin
Figure 15.1: Connections for analog inputs
The results for the equations presented in Section 9.1 ANALOG INPUTS in page 9-1 are shown on P018 or P020
according to the availability of analog inputs from the inverter. This readings can be used for options given by P231
or P236 or P241.
In case of speed reference function is selected by P231 or P236 or P241 = 0 this reference is going to be a
percentage of the maximum frequency(P134).
15
CFW300 | 15-1
15.1.1 Application 1 - Nominal speed
This example describes an application where the analogic input signal corresponds to a frequency reference. The
total excursion of analogic signal represents to command the motor to run from its minimum to maximum frequency
as presented on Figure 15.2 on page 15-2. Table 15.1 on page 15-2 show parameters related to the correct setting.
Requirements:
Motor: 1 HP, 220 V, 2.9 A, 1725 rpm, 60 Hz
Min. Frequency = 0 Hz
Max. Frequency = 60 Hz
Programming:
Table 15.1: Parameters for application 1

Analog Input AI1 AI2 Potenciometer Value
Min. Frequency P133 0.0 Hz
Max. Frequency P134 60.0 Hz
Max. Output Voltage P142 100.0 %
Interm. Output Voltage P143 50.0 %
Field Weak. Freq. P145 60.0 Hz
Intermediate Freq. P146 30.0 Hz
Selection source P220 0
Reference source P221 = 1 P221 = 2 P221 = 3 According application*
Rotation sel. P223 0
Signal function P231 P236 P241 0
Gain P232 P237 P242 1.000
Input signal P233 P238 - According application**
Offset P234 P239 P244 0%
(*) Consult Chapter 7 COMMAND AND REFERENCES on page 7-1.

(**) For AIx consult Section 9.1 ANALOG INPUTS on page 9-1, for potenciometer this parameter is not available.
Example:
Output
frequency
P134 (60 Hz) For AI1 set to 0-10 V (P233=0)

and an analog input of 5 V:
( )
5V
P018(%) = x (100.0 %) + 0.0 % x 1.000 = 50.0 %
10 V
Output Freq. = P018 x P134 = 50.0% x 60.0 Hz = 30.0 Hz
P133 (0 Hz) AIx Signal

0 ....................................... 10 V
0 ....................................... 20 mA
4 ....................................... 20 mA
10 V .................................... 0
20 mA ................................. 0
20 mA ............................... 4 mA
Figure 15.2: Result for application 1
15
15-2 | CFW300
15.1.2 Application 2 - Overspeed
as presented on Figure 15.3 on page 15-3. In this example, maximum speed is over the nominal speed (or field
weakeaning speed). Table 15.2 on page 15-3 show parameters related to the correct setting.
Requirements:
Motor: 1 HP, 220 V, 2.9 A, 1725 rpm, 60 Hz
Programming:
Gain P232 P237 P242 1.000
Offset P234 P239 P244 0%

Example:
Output
frequency
P134 (80 Hz) For AI1 set to 0-10 V (P233=0)

and an analog input of 5 V:
( )
5V
P018(%) = x (100.0 %) + 0.0 % x 1.000 = 50.0 %
10 V
Output Freq. = P018 x P134 = 50.0 % x 80.0 Hz = 40.0 Hz
P133 (0 Hz) AIx Signal

0 ....................................... 10 V
0 ....................................... 20 mA
4 ....................................... 20 mA
10 V .................................... 0
20 mA ................................. 0
20 mA ............................... 4 mA
15
CFW300 | 15-3
15.1.3 Application 3 - Forward/Reverse using Analog Input
total excursion of analogic signal represents to command the motor to run from its minimum to maximum frequency,
reversing the direction of rotation, as presented on Figure 15.4 on page 15-4. Table 15.3 on page 15-4 show
parameters related to the correct setting.
Requirements:
Motor: 1 HP, 220 V, 2.9 A, 1725 rpm, 60 Hz
Min. Frequency = -60 Hz (Reverse)
Programming:
Gain P232 P237 P242 2.000
Offset P234 P239 P244 -50.0 %

Example:
Output
frequency
For AI1 set to 0-10 V (P233=0):
Analog input of 10 V:
P134 (60 Hz) ( )
10 V
P018(%) = x (100.0 %) + (-50.0 %) x 2.000 = 100.0 %
10 V
Forward
( )
P133 (0 Hz) 5V
P018(%) = x (100.0 %) + (-50.0 %) x 2.000 = 0.0 %
10 V
Reverse Output Freq. = P018 x P134 = 0.0 % x 60.0 Hz = 0.0 Hz
( )
0V
- P134 (60 Hz) AIx Signal P018(%) = x (100.0 %) + (-50.0 %) x 2.000 = -100.0 %
10 V
0 .................. 5 V ............ 10 V
Output Freq. = P018 x P134 = -100.0 % x 60.0 Hz = -60.0 Hz
0 ..................10 mA ......... 20 mA
4 ................ 12 mA ......... 20 mA
10 V ............ 5 V ............... 0
20 mA ....... 10 mA ............ 0
20 mA ....... 12 mA ........... 4 mA
15
15-4 | CFW300
15.1.4 Application 4 - Analog input with dead zone
In this example, the output stay in 0Hz through the first 2.5V of analogic signal. The rotation of the motor (reverse)
only happens if the Dead Zone parameter is disable (P230 = 0), as presented on Figure 15.5 on page 15-5. Table
15.4 on page 15-5 show parameters related to the correct setting.
Requirements:
Motor: 1 HP, 220 V, 2.9 A, 1725 rpm, 60 Hz
Programming:
Gain P232 P237 P242 1.000
Offset P234 P239 P244 -25.0 %
Dead Zone** P230 1

(**) For AIx consult Section 9.1 ANALOG INPUTS on page 9-1 , for potenciometer this parameter is not available.
Example:
Output
Frequency
For AI1 set to 0-10 V (P233=0):

P134 (60 Hz)
Analog input 10 V:
( )
10 V
45 Hz P018(%) = x (100.0 %) + (-25.0 %) x 1.000 = 75.0 %
10 V
Analog input 2.5 V:
Forward ( )
2.5 V
P018(%) = x (100.0 %) + (-25.0 %) x 1.000 = 0.0 %
10 V
Analog input 0 V:
P133 (0 Hz) AIx Signal ( )
0V
Reverse P018(%) = x (100.0 %) + (-25.0 %) x 1.000 = -25.0 %
10 V
-15 Hz Output Freq. = P018 x P134 = -25.0 % x 60.0 Hz = -15.0 Hz
0 .................. 5 V ............ 10 V
0 ..................10 mA ......... 20 mA
4 ................ 12 mA ......... 20 mA
10 V ............ 5 V ............... 0
20 mA ....... 10 mA ............ 0
20 mA ....... 12 mA ........... 4 mA
15
CFW300 | 15-5
15.1.5 Application 5 - Reverse reference with Analog input
as presented on Figure 15.6 on page 15-6. Here the analog input is inverted when compared to Application 1.
Table 15.5 on page 15-6 show parameters related to the correct setting.
Requirements:
Motor: 1 HP, 220 V, 2.9 A, 1725 rpm, 60 Hz
Programming:
Rotation sel. P223 = 0 P223 = 0 P223 = 1 According application
Gain P232 P237 P242 1.000
Input signal P233 P238 - 2
Offset P234 = 0 % P239 = 0 % P244 = -100.0 % According application**

(**) For AIx consult Section 9.1 ANALOG INPUTS on page 9-1 , for potenciometer this parameter is not available.
Example:
Output
frequency For AI1 set to 10-0 V (P233=2)
and an analog input of 7.5 V:
( )
P134 (60 Hz) 7.5 V
P018(%) = 100.0 % - x (100.0 %) + 0.0 % x 1.000 = 25.0 %
10 V
Output Freq. = P018 x P134 = 25.0% x 60.0 Hz = 15.0 Hz
For potentiometer acessory with an analog input of 7.5 V one

need P244 = -100.0 % and P223 = 1:
( )
7.5 V
P018(%) = x (-100.0 %) + 0.0 % x 1.000 = -25.0 %
10 V
P133 (0 Hz) AIx Signal Output Freq. = P018 x P134 = -25.0% x 60.0 Hz = -15.0 Hz
0 ....................................... 10 V
0 ....................................... 20 mA
4 ....................................... 20 mA
10 V .................................... 0
20 mA ................................. 0
20 mA ............................... 4 mA
15
15-6 | CFW300
15.2 PID CONTROLLER APPLICATION
This example describes an application controlling a process in closed loop (PID Controller), as presented in Figure
15.7 on page 15-7. Table 15.6 on page 15-7 show parameters related to the correct setting.
Requirements:
The frequency inverter will be configured to operate in the local mode.
Digital input DI1 will be used for the Run/Stop command in local mode.
Digital input DI2 will be used to select the PID to Manual/Automatic.
The PID controller process variable (PV) will be connected to analog input AI1 in the scale of 4-20 mA, where
4 mA is equal to 0 bar (P922) and 20 mA is equal to 4.0 bar (P923).
The PID controller control setpoint (SP) will be via HMI (keys).
Example:
Pressure
Fuses Transducer
Line
DI1 - run / stop

Isolating switch DI2 - manual / automatic PID
Frequency
inverter
Process
Shield
Figure 15.7: Example of the PID controller application
Programming:
Table 15.6: Programming sequence of the PID controller application
Sequence Setting Action / Result
P903 1 = PID Controller It selects the PID controller application in the SoftPLC function of the inverter
P901 1 = Run Application It enables the execution of the PID controller application
P928 1 = Direct It selects the PID controller control action, thus enabling its operation and uploading, at this moment
the application default setting*
P133 40.0 Hz Minimum frequency
P134 60.0 Hz Maximum frequency
P233 1 = 4 to 20 mA Selection of the AI1 Signal Function
P911 2.00 Setting of the control Setpoint via HMI
P931 1.00 Proportional Gain of the PID controller
P932 5.00 Integral Gain of the PID controller
P933 0.00 Derivative Gain of the PID controller
(*) Consult Table 14.2 on page 14-4.
15
CFW300 | 15-7
WEG Drives & Controls - Automation LTDA.
Jaraguá do Sul - SC - Brazil
Phone 55 (47) 3276-4000 - Fax 55 (47) 3276-4020
São Paulo - SP - Brazil
Phone 55 (11) 5053-2300 - Fax 55 (11) 5052-4212
automacao@weg.net
www.weg.net

Weg CFW300

Uploaded by

Copyright:

Available Formats

Weg CFW300

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Weg CFW300

Uploaded by

Copyright:

Available Formats

Motors | Automation | Energy | Transmission & Distribution | Coatings

Software version: 3.0X

Publication Date: 10/2020

The information below describes the reviews made in this manual.

Version Revision Description

0 QUICK REFERENCE OF PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-1

1 QUICK REFERENCE OF ALARMS AND FAULTS . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

2 SAFETY NOTICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

3 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

4 ABOUT THE HMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

6 FREQUENCY INVERTER IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

7 COMMAND AND REFERENCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

8 MOTOR CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

10 FAULTS AND ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

0 QUICK REFERENCE OF PARAMETERS 0

Param. Description Adjustable Range Factory Setting Prop. Page

0 Param. Description Adjustable Range Factory Setting Prop. Page

Param. Description Adjustable Range Factory Setting Prop. Page 0

0 Param. Description Adjustable Range Factory Setting Prop. Page

Param. Description Adjustable Range Factory Setting Prop. Page 0

0 Param. Description Adjustable Range Factory Setting Prop. Page

Param. Description Adjustable Range Factory Setting Prop. Page 0

0 Param. Description Adjustable Range Factory Setting Prop. Page

Param. Description Adjustable Range Factory Setting Prop. Page 0

0 Param. Description Adjustable Range Factory Setting Prop. Page

Param. Description Adjustable Range Factory Setting Prop. Page 0

0 Param. Description Adjustable Range Factory Setting Prop. Page

Param. Description Adjustable Range Factory Setting Prop. Page 0

0 Param. Description Adjustable Range Factory Setting Prop. Page

Param. Description Adjustable Range Factory Setting Prop. Page 0

0 Param. Description Adjustable Range Factory Setting Prop. Page

Param. Description Adjustable Range Factory Setting Prop. Page 0

0 Param. Description Adjustable Range Factory Setting Prop. Page

SoftPLC Parameter Conﬁguration for PID Controller Application (P903 = 1)

SoftPLC Parameter Conﬁguration for PID Controller Application (P903 = 1) 0

1 QUICK REFERENCE OF ALARMS AND FAULTS

Fault / Alarm Description Possible Causes

F032 Main control cannot establish Accessory damaged.

Fault / Alarm Description Possible Causes

Fault / Alarm Description Possible Causes

Fault / Alarm Description Possible Causes

Faults and Alarms for PID Controller Application (P903 = 1)

Fault and alarm operation:

The following safety notices are used in this manual:

2.2 SAFETY NOTICES ON THE PRODUCT

E High voltages are present.

Components sensitive to electrostatic discharge. Do not touch them.

Mandatory connection to the protective earth (PE).

Connection of the shield to the ground.

2.3 PRELIMINARY RECOMMENDATIONS

Do not execute any applied potential test on the inverter!

3.1 TERMINOLOGY AND DEFINITIONS 3

3.1.1 Terms and Deﬁnitions Used

to the inverter user manual.

3 Nm: Newton meter; torque unit.

3.1.2 Numerical Representation

3.1.3 Symbols to Describe Parameter Properties

ro: read only parameter.

4 ABOUT THE HMI