Unisonic Technologies Co., LTD: PC Power Supply Supervisors
Unisonic Technologies Co., LTD: PC Power Supply Supervisors
Unisonic Technologies Co., LTD: PC Power Supply Supervisors
, LTD
S3515 CMOS IC
PC POWER SUPPLY
SUPERVISORS
DESCRIPTION
The UTC S3515 is specially designed for switching power supply
system. It provides over-voltage protection, over-current protection,
DIP-14
under-voltage protection, on/off control and power good signal generating.
OVP/UVP (Over/Under-Voltage Protection) monitors 3.3V, 5V and
double 12V to protect our power supply and PC, FPO goes to high when
one of these supply voltages exceeds their normal operation voltage
range.
OCP (Over Current Protection) monitors IS33, IS5, IS12 input
current. The voltage difference across external current shunt is used for
OCP functions. An external resistor which is connected between the RI
pin and the GND pin can be used to adjust protection threshold. To SOP-14
achieve better immunity for lighting surge glitch and to prevent
accidental power shut down during dynamic loading condition, the
de-bounce time for UVP/OCP is 73us respectively. The deglitch time for
OVP is 73uS for better noise immunity.
The power supply is turned on after 38mS de-bounce time when
PSON signal is set from high to low. To turn off power supply, PSON
signal is set from low to high and the de-bounce time is 115mS. When
PGI input voltage level is lower than the internal 1.15V reference
voltage, after 73uS de-bounce time, the PGO signal is pulled low.
FEATURES
* Over/Under-Voltage Protection for 3.3V, 5V, and Two 12V
* Over-Current Protection for 3.3V, 5V, and Two 12V
* PGO and FPO pins with Open Drain Output Stage
* 300mS Power Good Delay from PGI to PGO
* 75mS Delay for 3.3V, 5V and 12V Power Turn on
* 2.8mS Delay for PSON Control to FPO Turn off
* 38mS / 115mS PSON on/off De-Bounce Time
* 73uS width Noise Deglitches
* 73uS De-Bounce Time for UVP and OCP
* Wide Supply Voltage Range
ORDERING INFORMATION
Ordering Number
Package Packing
Lead Free Plating Halogen Free
S3515L-D14-T S3515G-D14-T DIP-14 Tube
S3515L-S14-R S3515G-S14-R SOP-14 Tape Reel
S3515L-S14-T S3515G-S14-T SOP-14 Tube
www.unisonic.com.tw 1 of 8
Copyright © 2010 Unisonic Technologies Co., Ltd QW-R502-073,B
S3515 CMOS IC
PIN CONFIGURATION
PGI 1 14 PGO
GND 2 13 VDD
FPO 3 12 VS5
PSON 4 11 VS33
IS12 5 10 VS12
RI 6 9 IS33
VS12B 7 8 IS5
PIN DESCRIPTION
PIN NO PIN NAME TYPE DESCRIPTION
1 PGI input Power good input.
3 FPO output Fault protection output, open drain output stage.
Power on/off control signal sends from CPU or main-board. The power
4 PSON input
supply will be turned on/off after 38mS/115mS respectively.
8 IS5 input 5V over current protection.
9 IS33 input 3.3V over current protection.
12V over current protection. Regarding typical application, this pin is
connected to the positive end of a current shunt through one resistor.
When the voltage on IS12 is higher than that of VS12 by 5mV, OCP
5 IS12 input will be enabled. One current sink, 8 x IREF, is used to determine the
voltage drop between the positive end of the current shunt and VS12.
Adjusting the value of the external resistor can adjust the threshold for
OCP accordingly. The operation for IS5 or IS33 is the same.
Current sense setting. An external resistor Ri is connected between RI
6 RI input pin and GND pin will adjust a reference current, IREF = 1.15/Ri, for OCP
function.
12 VS5 input 5V over/under-voltage protection.
7 VS12B input Second 12V over/under-voltage protection.
10 VS12 input 12V over/under-voltage protection.
11 VS33 input 3.3V over/under-voltage protection.
13 VDD power Supply voltage. 4V ~ 15V.
Power good logic output, open drain output stage. The power good
14 PGO output
delay is 300mS from PGI to PGO.
2 GND power Ground.
BLOCK DIAGRAM
RST
PGO
VREF - 300ms
UN 73µs clr
PGI + delay
debounce
V12A
-
IS 33 +
I REF×8
V12A
-
IS5 VREF=1.15 V +
+ I REF=VREF/RI
-
I REF×8
RI
V12A
-
IS12 +
V12A
-
+
I REF×8
VDD
PSON TPSON(OFF)
TPSON(ON)
FPO
TOVP
PGI
T PSOFF
TPG
PGO
3.3V,5V,12V
VDD
PSON
FPO
PGI
TOVP TUVP
PGO
12V
OCP
TOCP
UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.