7 USER MANUAL FOR

DP C18.CAN

USER MANUAL FOR DISPLAY

CONTENT
7.1 Important Notice  2 7.6.3  Selection Mode 5
7.2 Introduction of Display 2 7.6.4  Headlights / backlighting 6
7.3 Product Description 3 7.6.5 ECO/SPORT Modus 6
7.3.1  Specifications 3 7.6.6  Walk Assistance 7
7.3.2  Functions Overview 3 7.6.7  SERVICE 7
7.4 Display 4 7.7 Settings 8
7.5 Key Definition 4 7.7.1  “Display setting” 8
7.6 Normal Operation 5 7.7.2  “Information” 12
7.6.1  Switching the System ON/OFF 5 7.8 Error Code Definition 14
7.6.2  Selection of Support Levels 5

   BF-UM-C-DP C18-EN November 2019 1

7.1 IMPORTANT NOTICE
•• If the error information from the display •• Please use this product with care.
cannot be corrected according to the inst- •• Do not use thinners or other solvents to
ructions, please contact your retailer. clean the display. Such substances can
•• The product is designed to be waterproof. It damage the surfaces.
is highly recommended to avoid submerging •• Warranty is not included due to wear and
the display under water. normal use and aging.
•• Do not clean the display with a steam jet,
high-pressure cleaner or water hose.

7.2 INTRODUCTION OF DISPLAY

•• Model: DP C18.CAN BUS •• The label marking is as follows:
•• The housing material is PC; the Display Glass
is made of high-currentem material:
DPC18CP10101.0
PD051205

Note: Please keep the QR code label attached

to the display cable. The information from the
Label is used for a later possible software
update.

2 BF-UM-C-DP C18-EN November 2019  

7.3 PRODUCT DESCRIPTION

7.3.1 Specifications 7.3.2 Functional Overview

USER MANUAL FOR DISPLAY

•• Speed display (including top speed and
•• Operating temperature: -20℃~45℃
average speed, switching between km and
•• Storage temperature: -20℃~50℃ miles).
•• Waterproof: IP65 •• Battery capacity indicator.
•• Bearing humidity: 30%-70% RH •• Automatic sensors explanation of the light-
ing system.
•• Brightness setting for backlight.
•• Indication of performance support.
•• Motor output power and output current
indicator.
•• Kilometer stand (including single-trip
distance, total distance and remaining
distance).
•• Walk assistance.
•• Setting the support levels.
•• Energy consumption indicator CALORIES
(Note: If the display has this function).
•• Display for the remaining distance.
(Depends on your riding style)
•• Setting password.

   BF-UM-C-DP C18-EN November 2019 3

7.4 DISPLAY
6
3 The display shows this symbol, if the
1
2 7
light is on.
3 8 4 Speed Graphics
5 Trip: Daily kilometers (TRIP) - Total kilometers
(ODO) - Top speed (MAX) - Average speed
4 (AVG) - Range (RANGE) - Energy Consump-
9
tion (CALORIES(only with torque sensor
fitted)) - Travel time (TIME).

10
6 Display of battery capacity in real time.
5 11 7 Voltage indicator in voltage or in percent.
SERVICE
12 8 Digital speed display.
9 Power indicator in watts / amperes.
10 Support level/ Walking assistance
1 Time
11 Data: Display data, which corresponds to the
2 USB charging indicator displays the icon , if current mode.
an external USB device is connected to the
12 Service: Please see the service section
display.

7.5 KEY DEFINITION

Light On/Off

Up

System On/Off

Down

Ok/Enter

4 BF-UM-C-DP C18-EN November 2019  

7.6 NORMAL OPERATION

7.6.1 Switching the System ON/OFF

USER MANUAL FOR DISPLAY

Press and hold (>2S) on the display to turn on the system. Press and hold (>2S) again to turn
off the system.
If the "automatic shutdown time" is set to 5 minutes (it can be set with the "Auto Off" function, See
"Auto Off"), the display will automatically be turned off within the desired time when it is not in op-
eration. If the password function is enabled, you must enter the correct password to use the system.

7.6.2 Selection of Support Levels

When the display is turned on, press the or (<0.5S) button to switch to the support level, the
lowest level is 0, the highest level is 5. When the system is switched on, the support level starts in
level 1. There is no support at level 0.

7.6.3 Selection Mode

Briefly press the (0.5s) button to see the different trip modes.
Trip: daily kilometers (TRIP) - total kilometers (ODO) - Maximum speed (MAX) - Average speed (AVG) -
Range (RANGE) - Energy consumption (CALORIES(only with torque sensor fitted)) - Travel time (TIME).

   BF-UM-C-DP C18-EN November 2019 5

7.6.4 Headlights / backlighting
Hold the (>2S) button to activate the headlight and taillights.
Hold the (>2S) button again to turn off the headlight. The brightness of the backlight can be set
in the display settings "Brightness". If the display /Pedelec is switched on in a dark environment,
the display backlight/headlight will automatically be switched on. If the display backlight/headlight
has been manually switched off, the automatic sensor function is deactivated. You can only turn on
the light manually. After switching on the system again.

7.6.5 ECO/SPORT Modus

Press and hold the (<2S) Button, to change from ECO mode to Sport mode.
(Depending on the version of the pedelec manufacturer)

6 BF-UM-C-DP C18-EN November 2019  

 USER MANUAL FOR DISPLAY
7.6.6 Walk Assistance
The Walk assistance can only be activated with a standing pedelec.
Activation: Press the button until this symbol appears. Next hold down the button whilst
the symbol is displayed. Now the Walk assistance will activate. The symbol will flashes and
the pedelec moves approx. 6 km/h. After releasing the button, the motor stops automatically and
switches back to level 0.

7.6.7 SERVICE
The display shows "Service" as soon as a certain number of kilometers or battery charges has been
reached. With a mileage of more than 5000 km (or 100 charge cycles), the “Service" function is
displayed on the display. Every 5000 km the display "SERVICE" is displayed every time. This function
can be set in the display settings.

   BF-UM-C-DP C18-EN November 2019 7

7.7 SETTINGS
After the display is turned on, quickly 7.7.1 “Display setting”
press the button twice, to access the
Press the or (<0.5S) button to select
“SETTINGS” menu. By pressing the or
Display Settings, and then briefly press the
(<0.5S) button, you can select: Display
(<0.5S) button to access the following
Settings, Information or EXIT. Then press the
selections.
(<0.5S) button to confirm your selected
option.
Or select "EXIT" and press the (<0.5S)
button to return to the main menu, or select
"BACK" and press the (<0.5S) button to
return to the Settings interface.
If no button is pressed within 20 seconds,
the display will automatically return to the
main screen and no data will be saved.

7.7.1.1 “Unit” Selections in km/Miles

Press the or (<0.5S) button to high-
light “Unit” in the Display settings menu,
and then press the (<0.5S) button to
select. Then with the or button
choose between “Metric” (kilometer) or
“Imperial” (Miles). Once you have chosen
your desired selection, press the (<0.5S)
button to save and exit to the "Display
setting" interface.
You can quickly press the (<0.5S)
button twice at any time, to return to the
main screen.

8 BF-UM-C-DP C18-EN November 2019  

7.7.1.2 “Service Tip” Switching the menu, and then press (<0.5S) to select.
notification on and off

USER MANUAL FOR DISPLAY

Then with the or button choose
Press the or (<0.5S) button to between “3/5/9” (the amount of support
highlight “Service tip” in the Display settings levels). Once you have chosen your desired
menu, and then press (<0.5S) to select. selection, press the (<0.5S) button to
Then with the or button choose save and exit to the "Display setting"
between “ON” or “OFF”. Once you have
chosen your desired selection, press the
7.7.1.6 “Default Mode” Set for ECO/Sport
(<0.5S) button to save and exit to the
mode
"Display setting" interface.
Press the or (<0.5S) button to high-
light “Default Mode” in the Display settings
7.7.1.3 “Brightness” Display brightness menu. Then press (<0.5S) to select. Then
Press the or (<0.5S) button to high- with the or button choose between
light “Brightness” in the Display settings “ECO” or “Sport”. Once you have chosen
menu. Then press (<0.5S) to select. Then your desired selection, press the (<0.5S)
with the or button choose between button to save and exit to the "Display
"100%" / "75%" / "50%" /" 30%"/"10%" . setting" interface.
Once you have chosen your desired selec-
tion, press the (<0.5S) button to save and
7.7.1.7 “Power View” Setting the power
exit to the "Display setting" interface.
indicator
Press the or (<0.5S) button to high-
7.7.1.4 “Auto Off” Set Automatic system light “Power View” in the Display settings
switch off time menu, and then press (<0.5S) to select.
Press the or (<0.5S) button to Then with the or button choose
highlight “Auto Off” in the Display settings between “Power” or “Current”. Once you
menu, and then press (<0.5S) to select. have chosen your desired selection, press
Then with the or button choose the (<0.5S) button to save and exit to the
between “OFF”, "9"/"8"/"7"/"6"/"5"/"4"/"3" "Display setting" interface.
/"2"/"1", (The numbers are measured in
minutes). Once you have chosen your de-
sired selection, press the (<0.5S) button
to save and exit to the "Display setting"
interface.

7.7.1.5 “MAX PAS” Support level

(Function not available with ECO/SPORT display)
Press the or (<0.5S) button to
highlight “Max Pass” in the Display settings

   BF-UM-C-DP C18-EN November 2019 9

7.7.1.8 “SOC View” Battery view in volt 7.7.1.11 “Password”
percent Press the or (<0.5S) button to choose
Press the or (<0.5S) button to Password in the menu. Then by briefly
highlight “SOC View” in the Display settings pressing (<0.5S) to enter the password
menu, and then press (<0.5S) to select. selection. Now again with the or
Then with the or button choose (<0.5S) buttons highlight “Start Password"
between “percent” or “voltage “. Once you and press the (<0.5S) button to confirm.
have chosen your desired selection, press Now again using the or (<0.5S)
the (<0.5S) button to save and exit to the Button choose between “ON” or “OFF” and
"Display setting" press the (<0.5S) button to confirm.
Now you can input your 4-digit pin code. By
using the or (<0.5S) button choose
numbers between "0-9". By briefly pressing
the (<0.5S) button you can move on to
the next number.
After entering your desired 4-digit code,
you must re-enter the 4-digits you chose, to
ensure the code is correct.
After selecting a password, the next time
7.7.1.9 “TRIP Reset” Reset mileage you turn on the system it will ask you to
Press the or (<0.5S) button to high- input your password. Press the or
light “TRIP Reset” in the Display settings (<0.5S) button to select the numbers, Then
menu, and then press (<0.5S) to select. press briefly (<0.5S) to confirm.
Then with the or button choose After entering the wrong number three
between “YES” or “NO”. Once you have times, the system switches off. If you have
chosen your desired selection, press the forgotten the password, please contact your
(<0.5S) button to save and exit to the retailer.
"Display setting"
7.7.1.10 “AL Sensitivity” Automatic
headlight sensitivity
Press the or (<0.5S) button to high-
light “AL-Sensetivity” in the Display settings
menu, and then press (<0.5S) to select.
Then with the or button choose be-
tween "0" / " 1" / " 2"/ "3" / "4"/ "5"/ "OFF”.
Once you have chosen your desired selection
, press the (<0.5S) button to save and
exit to the "Display setting"

10 BF-UM-C-DP C18-EN November 2019  

 USER MANUAL FOR DISPLAY
Changing the password:
Press the or (<0.5S) button to choose Password in the menu. Then by briefly pressing
(<0.5S) to enter the password section. Now again with the or (<0.5S) button highlight “Pass-
word set" and press the (<0.5S) button to confirm. Now with the or (<0.5S) buttons and
highlight “Reset Password” and with the (<0.5S) button to confirm.
By entering your old password once, followed by inputting the new password twice, then your
password will be changed.

Deactivating the password:

To deactivate the password, use the or buttons to get to the menu point “Password” and
press the (<0.5S) button to highlight your selection. Press the or (<0.5S) button until is
shows “OFF”. Then press briefly (<0.5S) to select.
Now enter your password, to deactivate it.

   BF-UM-C-DP C18-EN November 2019 11

7.7.1.12 “Set Clock” 7.7.2.2 Battery Information
Press the or (<0.5S) Button to access Press the or (<0.5S) button to access
the “Set Clock” menu. Then briefly press the the Battery Info menu, and then press the
(<0.5S) button to confirm selection. Now (<0.5S) button to select confirm. Now
press the or (<0.5S) button and input press the or (<0.5S) button and select
the correct number (time) and press the "Back” or “Next Page". Then press the
(<0.5S) button to move to the next number. (<0.5S) button to confirm, now you can read
After entering the correct time, press the the battery information.
(<0.5S) button to confirm and save.
Content Explanation
7.7.2 “Information”
Current temperature in
TEMP
Once the system is turned on, quickly Press the degrees (°C)
(<0.5S) button twice to access the "SET-
TotalVolt Voltage (V)
TINGS" menu. Press or (<0.5S) button
to select "Information", and then press the Current Discharge (A)
(<0.5S) button to confirm your selection.
Remaining Capacity
Or select the point "EXIT" by confirming with the Res Cap (A/h)
(<0.5S) button to return to the main menu.
Full Cap Total Capacity (A/h)

Default Loader Status

RelChargeState (%)

AbsChargeState Instant charge (%)

Charging cycles
Cycle Times (number)

Maximum time in
Max Uncharge Time which no charge was
made (Hr)

Last Uncharge Time

Total Cell Number (individual)

Cell Voltage 1 Cell Voltage 1 (m/V)

7.7.2.1 Wheel Size and Speed Limit Cell Voltage 2 Cell Voltage 2 (m/V)

The "Wheel Size” and "Speed Limit” cannot Cell Voltage n Cell Voltage n (m/V)
be changed, this information is here to be
HW Hardware Version
viewed only.
SW Software Version

NOTE: If no data is detected, "--" is displayed.

12 BF-UM-C-DP C18-EN November 2019  

7.7.2.3 Controller Information 7.7.2.5 Torque Information

USER MANUAL FOR DISPLAY

Press the or (<0.5S) button and select Press the or (<0.5S) button and select
"CTRL Info", and then press the (<0.5S) “Torque info”, then press the (<0.5S) but-
button to confirm. Now you can read the ton to read the software and hardware data
controller information. To Exit press the in the display. To Exit press the (<0.5S)
(<0.5S) button, once “EXIT” is highlighted to button, once “EXIT” is highlighted to return
return to the information settings. to the information settings.

7.7.2.4 Display Information 7.7.2.6 Error Code

Press the or (<0.5S) button and select Press the or (<0.5S) button and select
Display Info, then press the (<0.5S) but- “Error Code”, and then press the (<0.5S)
ton to read the software and hardware data button to confirm. It shows error informa-
in the display. To Exit press the (<0.5S) tion for the last ten errors of the pedelec.
button, once “EXIT” is highlighted to return Error code "00"means that there is no error.
to the information settings. To return to the menu press the (<0.5S)
button, once "BACK" is highlighted to return
to the information settings.

   BF-UM-C-DP C18-EN November 2019 13

7.8 ERROR CODE DEFINITION
The display can show the errors of a pedelec. If an error is detected, the wrench icon appears on the display
and one of the following error codes will be displayed.

Note: Please read the description of the error code carefully. If you see the error code, restart the system first. If the
problem is not resolved, please contact your dealer.

Error Declaration Troubleshooting

Check the throttle can adjust back into its

The throttle is not back in its correct correct position, if the situation does not
04
position. improve, please change to a new throttle.(only
with this function)

1. Check the connector of throttle whether

they are correctly connected.
05 The throttle has fault. 2. Disconnect the throttle, If the problem still
occurs, please contact your retailer.
(only with this function)

1. Remove the battery.

2. Re-Insert the battery.
07 Overvoltage protection
3. If the problem persists, please contact your
retailer.

Error with the hall sensor signal

08 Please contact your retailer.
inside the motor

09 Error with the Engine phase’s Please contact your retailer.

1. Turn off the system and allow the Pedelec

The temperature inside the engine
to cool down.
10 has reached its maximum protection
2. If the problem persists, please contact your
value
retailer.

The temperature sensor inside the

11 Please contact your retailer.
motor has an error

Error with the current sensor in the

12 Please contact your retailer.
controller

Error with the temperature sensor

13 Please contact your retailer.
inside of the battery

14 BF-UM-C-DP C18-EN November 2019  

Error Declaration Troubleshooting

USER MANUAL FOR DISPLAY

1. Turn off the system and let the pedelec cool
The protection temperature inside
down.
14 the controller has reached its maxi-
2. If the problem persists, please contact your
mum protection value
retailer.

Error with the temperature sensor

15 Please contact your retailer.
inside the controller

1. Restart the system

2. Check that the magnet attached to the
spoke is aligned with the speed sensor and
that the distance is between 10 mm and 20
21 Speed sensor Error mm.
3. Check that the speed sensor connector is
connected correctly.
4. If the error persists, please contact your
retailer.

1. Check that all connections are connected

correctly.
25 Torque signal Error
2. If the error persists, please contact your
retailer.

1.Check the connector from the speed sensor

to make sure it is connected correctly.
Speed signal of the torque sensor has
26 2.Check the speed sensor for signs of damage.
an error
3.If the problem persists, please contact your
retailer.

27 Overcurrent from controller Please contact your retailer.

1. Check all connections are correctly con-

nected.
30 Communication problem
2. If the error persists, please contact your
retailer.

1. Check all connectors.

Brake signal has an error
33 2. If the error continues to occur, please con-
(If brake sensors are fitted)
tact your retailer.

   BF-UM-C-DP C18-EN November 2019 15

Error Declaration Troubleshooting

35 Detection circuit for 15V has an error Please contact your retailer.

Detection circuit on the keypad has

36 Please contact your retailer.
an error

37 WDT circuit is faulty Please contact your retailer.

Total voltage from the battery is too

41 Please contact your retailer.
high

Total voltage from the battery is too

42 Please contact your retailer.
low

Total power from the battery cells is

43 Please contact your retailer.
too high

44 Voltage of the single cell is too high Please contact your retailer.

Temperature from the battery is too

45 Please contact your retailer.
high

The temperature of the battery is

46 Please contact your retailer.
too low

47 SOC of the battery is too high Please contact your retailer.

48 SOC of the battery is too low Please contact your retailer.

Please contact your retailer. (only with this

61 Switching detection defect
function)

Please contact your retailer. (only with this

62 Electronic derailleur cannot release.
function)

Please contact your retailer. (only with this

71 Electronic lock is jammed
function)

Please contact your retailer. (only with this

81 Bluetooth module has an error
function)

16 BF-UM-C-DP C18-EN November 2019