Discontinued Product: A1301 and A1302
Discontinued Product: A1301 and A1302
Discontinued Product: A1301 and A1302
Discontinued Product
This device is no longer in production. The device should not be
purchased for new design applications. Samples are no longer available.
For existing customer transition, and for new customers or new appli-
cations, contact Allegro Sales.
Allegro MicroSystems reserves the right to make, from time to time, revisions to the anticipated product life cycle plan for a
product to accommodate changes in production capabilities, alternative product availabilities, or market demand. The infor-
mation included herein is believed to be accurate and reliable. However, Allegro MicroSystems assumes no responsibility for
its use; nor for any infringements of patents or other rights of third parties which may result from its use.
A1301 and A1302
Continuous-Time Ratiometric Linear Hall-Effect Sensor ICs
V+
VCC
To all subcircuits
VOUT
Filter
Amp Out
Gain Offset
CBYPASS
Trim
Control
GND
SPECIFICATIONS
Selection Guide
Part Number Packing* Package Ambient, TA Sensitivity (Typical)
A1301EUA-T Bulk, 500 pieces/bag SIP –40ºC to 85ºC
A1301KLHLT-T 7-in. reel, 3000 pieces/reel Surface Mount
2.5 mV/G
A1301KLHLX-T 13-in. reel, 10000 pieces/reel Surface Mount –40ºC to 125ºC
A1301KUA-T Bulk, 500 pieces/bag SIP
A1302ELHLT-T 7-in. reel, 3000 pieces/reel Surface Mount
–40ºC to 85ºC
A1302ELHLX-T 13-in. reel, 10000 pieces/reel Surface Mount
A1302KLHLT-T 7-in. reel, 3000 pieces/reel Surface Mount 1.3 mV/G
A1302KLHLX-T 13-in. reel, 10000 pieces/reel Surface Mount –40ºC to 125ºC
A1302KUA-T Bulk, 500 pieces/bag SIP
*Contact Allegro™ for additional packing options.
1 2 1 2 3
Package LH SOT23W Pin-out Diagram Package UA, 3-Pin SIP Pin-out Diagram
Terminal List
Number
Symbol Description
Package LH Package UA
VCC 1 1 Connects power supply to chip
VOUT 2 3 Output from circuit
GND 3 2 Ground
2
Allegro MicroSystems
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
A1301 and
Continuous-Time Ratiometric Linear Hall-Effect Sensor ICs
A1302
DEVICE CHARACTERISTICS over operating temperature range, TA, and VCC = 5 V, unless otherwise noted
Characteristic Symbol Test Conditions Min. Typ. Max. Units
Electrical Characteristics
Supply Voltage VCC Running, TJ < 165°C 4.5 – 6 V
Supply Current ICC Output open – – 11 mA
VOUT(High) ISOURCE = –1 mA, Sens = nominal 4.65 4.7 – V
Output Voltage
VOUT(Low) ISINK = 1 mA, Sens = nominal – 0.2 0.25 V
Output Bandwidth BW – 20 – kHz
VCC(min) to 0.95 VOUT; B = ±1400 G;
Power-On Time tPO – 3 5 µs
Slew rate = 4.5 V/µs to 4.5 V/100 ns
Output Resistance ROUT ISINK ≤ 1 mA, ISOURCE ≥ –1 mA – 2 5 Ω
External output low pass filter ≤ 10 kHz;
Wide Band Output Noise, rms VOUTN – 150 – µV
Sens = nominal
Ratiometry
Quiescent Output Voltage Error with
ΔVOUTQ(V) TA = 25°C – – ±3.0 %
respect to ∆VCC1
Magnetic Sensitivity Error with
ΔSens(V) TA = 25°C – – ±3.0 %
respect to ∆VCC2
Output
Linearity Lin TA = 25°C – – ±2.5 %
Symmetry Sym TA = 25°C – – ±3.0 %
Magnetic Characteristics
Quiescent Output Voltage VOUTQ B = 0 G; TA = 25°C 2.4 2.5 2.6 V
Quiescent Output Voltage over
Operating Temperature Range
VOUTQ(ΔTA) B=0G 2.2 – 2.8 V
3
Allegro MicroSystems
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
A1301 and
Continuous-Time Ratiometric Linear Hall-Effect Sensor ICs
A1302
CHARACTERISTIC DEFINITIONS
VOUTQ(ΤΑ) – VOUTQ(25ºC) and the ratiometric change (%) in sensitivity is defined as:
∆VOUTQ(∆ΤΑ) = (1)
Sens(25ºC) Sens(VCC) Sens(5V)
∆Sens(∆V) = × 100% (5)
where Sens is in mV/G, and the result is the device equivalent VCC 5V
accuracy, in gauss (G), applicable over the entire operating tem-
perature range. Linearity and Symmetry
The on-chip output stage is designed to provide linear output at
Sensitivity a supply voltage of 5 V. Although the application of very high
The presence of a south-polarity (+B) magnetic field, perpen- magnetic fields does not damage these devices, it does force
dicular to the branded face of the device package, increases the their output into a nonlinear region. Linearity in percent is mea-
output voltage, VOUT, in proportion to the magnetic field applied, sured and defined as:
from VOUTQ toward the VCC rail. Conversely, the application
of a north polarity (–B) magnetic field, in the same orientation, VOUT(+B) – VOUTQ
proportionally decreases the output voltage from its quiescent
Lin+ = × 100% (6)
2 (VOUT(+B½) – VVOUTQ )
value. This proportionality is specified as the magnetic sensitiv-
ity of the device and is defined as:
VOUT(–B) – VOUTQ
VOUT(–B) – VOUT(+B) Lin– = × 100% (7)
Sens =
(2) 2(VOUT(–B½) – VOUTQ)
2B
and output symmetry as:
The stability of the device magnetic sensitivity as a function of
ambient temperature, ∆ Sens (∆TA) (%) is defined as:
Sens(ΤΑ) – Sens(25ºC) VOUT(+B) – VOUTQ
∆Sens(∆ΤΑ) = × 100% (3) Sym = × 100% (8)
Sens(25ºC) VOUTQ – VOUT(–B)
4
Allegro MicroSystems
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
A1301 and
Continuous-Time Ratiometric Linear Hall-Effect Sensor ICs
A1302
TYPICAL CHARACTERISTICS
(30 pieces, 3 fabrication lots)
1301 Device Sensitivity vs. Ambient Temperature 1302 Device Sensitivity vs. Temperature
2.65 1.40
1.38
2.60 UA Package
UA Package 1.36
Sensitivity (mV/G)
Sensitivity (mV/G)
2.55 1.34
2.50 1.32
LH Package 1.30
2.45 LH Package
1.28
2.40
1.26
2.35 1.24
–50 –25 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150
Temperature (°C) Temperature (°C)
1301 Device VOUTQ vs. Ambient Temperature 1302 Device VOUTQ vs. Ambient Temperature
2.60 2.60
2.55
Output Voltage (V)
2.55
Output Voltage (V)
2.50 2.50
2.45 2.45
2.40 2.40
–50 –25 0 25 50 75 100 125 150 –50 –25 0 25 50 75 100 125 150
Temperature (°C) Temperature (°C)
1301 Device Sensitivity vs. Supply Voltage 1302 Device Sensitivity vs. Supply Voltage
3.5 1.7
1.6
3.0 1.5
Sensitivity (mV/G)
Sensitivity (mV/G)
1.4
2.5
1.3
1.2
2.0
1.1
1.5 1.0
4.5 5.0 5.5 6.0 4.5 5.0 5.5 6.0
Supply Voltage (V) Supply Voltage (V)
5
Allegro MicroSystems
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
A1301 and
Continuous-Time Ratiometric Linear Hall-Effect Sensor ICs
A1302
1301 Device VOUTQ vs. Supply Voltage 1302 Device VOUTQ vs. Supply Voltage
3.5 3.5
3.0 3.0
2.5 2.5
2.0 2.0
1.5 1.5
4.5 5.0 5.5 6.0 4.5 5.0 5.5 6.0
Supply Voltage (V) Supply Voltage (V)
1301 Device LIN+ and LIN– vs. Supply Voltage 1302 Device LIN+ and LIN– vs. Supply Voltage
100.4 100.0
100.3
LIN+
LIN– 99.9
100.2
Linearity (%)
Linearity (%)
100.1 99.8
LIN–
100.0
LIN+ 99.7
99.9
99.8 99.6
4.5 5.0 5.5 6.0 4.5 5.0 5.5 6.0
Supply Voltage (V) Supply Voltage (V)
1301 Device Symmetry vs. Supply Voltage 1302 Device Symmetry vs. Supply Voltage
100.0 100.5
99.9 100.4
99.8 100.3
99.7 100.2
Symmetry (%)
Symmetry (%)
99.6 100.1
99.5 100.0
99.4 99.9
99.3 99.8
99.2 99.7
99.1 99.6
99.0 99.5
4.5 5.0 5.5 6.0 4.5 5.0 5.5 6.0
Supply Voltage (V) Supply Voltage (V)
6
Allegro MicroSystems
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
A1301 and
Continuous-Time Ratiometric Linear Hall-Effect Sensor ICs
A1302
0.96 D
1.00
0.25 MIN
1 2
0.55 REF
0.25 BSC 0.95
Seating Plane
Gauge Plane
B PCB Layout Reference View
Branded Face
8X 10° REF
1.00 ±0.13
NNN
+0.10
0.05
–0.05 C Standard Branding Reference View
0.95 BSC 0.40 ±0.10 N = Last three digits of device part number
7
Allegro MicroSystems
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
A1301 and
Continuous-Time Ratiometric Linear Hall-Effect Sensor ICs
A1302
2 X 45°
+0.08
4.09
–0.05 1.52 ±0.05
E C
2.04
3 X 10°
1.44 E E Mold Ejector
+0.08 Pin Indent
3.02
–0.05
Branded 45°
Face
1.02 MAX
0.51 MAX
A
0.79 REF
1 2 3
+0.05 +0.03
0.43 0.41
–0.07 –0.06
1.27 NOM
NNN
14.99 ±0.25
8
Allegro MicroSystems
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com
A1301 and
Continuous-Time Ratiometric Linear Hall-Effect Sensor ICs
A1302
Revision History
Revision Revision Date Description of Revision
18 April 26, 2013 Update UA package drawing
19 January 1, 2015 Add LX option to Selection Guide
20 July 13, 2015 Corrected LH package Active Area Depth value
21 December 1, 2015 Updated product status to “Not for New Design”
22 December 5, 2016 Updated product status to “Last Time Buy”
23 February 14, 2019 Updated product status to “Discontinued”
24 March 6, 2020 Minor editorial updates
www.allegromicro.com
9
Allegro MicroSystems
955 Perimeter Road
Manchester, NH 03103-3353 U.S.A.
www.allegromicro.com