650

1/16 DIN PID TEMPERATURE CONTROLLER

Main features
• Operator interface with large LCD Display,
customizable, with choice of colors
• Scrolling diagnostics messages,
configurable, in the selected language
• Easy, guided configuration, copy/paste
parameters even with power off
• Preventive maintenance with energy
counters (kWh) and load switching
• 16 function block applications
• Timer, setpoint and algorithm programmer for
controlling motorized valves
• Advanced tuning of control parameters
• Different password levels
• Universal input configurable for thermocouples,
resistance thermometers, linear inputs
• Remote setpoint input
• Relay, logic, isolated analog outputs
• Up to two CT inputs for interrupted load
diagnostics
• RS485 serial communication in Modbus RTU
• Removable faceplate for immediate
replacement
Dimensions 48×48×80 mm (1/16 DIN)
• Sampling time 60ms

PROFILE The initial parameters can always be reset, Timer

both from the keypad and from the GF_eX- Three types of timers let you set delay ti-
Operator interface press Software tool. mes before activating the control, hold ti-
Large LCD display with customization of mes on the setpoint value, and timed chan-
colors assigned to PV and SV display, of Diagnostics, Preventive Maintenance, ges of programmed setpoints.
color of plastic faceplate, and of logo. and Energy Monitor
Scrolling alphameric display of 25 mes- Complete diagnostics for broken or incor- Setpoint Programmer
sages (32 letters each), completely confi- rectly connected probe, total or partial load Models with twelve ramp and hold steps,
gurable and savable, in three languages. break, out of range variables, and control groupable in four programs, with enable
Thanks to language selection and clear loop faults. inputs and event outputs, are available for
scrolling messages for diagnostics, alarms, Thanks to the switching count and to the applications with setpoint profiles.
and process state, the controller speaks settable alarm thresholds, you can pro- On-board configuration and graphic confi-
the user’s language. gram preventive maintenance to replace guration with GF_eXpress.
worn actuators.
Easy Configuration An internal energy counter with alarm for Valve Positioner
Guided configuration for manual-free pro- abnormal variations totalizes energy con- Models to control motorized valves, wi-
gramming, with a few essential parameters sumptions and costs for constant control thout feedback.
and on-line help messages. Valve position is calculated and shown on
Ability to clone configuration among con- Function block applications the display.
trollers, even with power off and in the Sixteen AND, OR, Timer Function Blocks
field, thanks to a mini portable configurator let you create customizable logic sequen- General characteristics
with Zapper battery. ces for complete and flexible machine con- The controller is completely software con-
Extended configuration, creation of work trol. figurable without accessing the internal
recipes, and firmware updates via PC and The controller’s hardware resources are electronics.
GF_eXpress software, even without powe- exploited completely, without any need for The universal main input accepts thermo-
ring the controllers. external devices such as timers and small couple sensors, resistance thermometers,
Thanks to the Smart Configurator function, PLCs and linears.
you obtain the required parameter recipe The controller can be replaced at any time
by answering a few simple questions. Tuning simply by removing the faceplate, without
Local configuration and operation with Advanced tuning algorithms ensure stable any additional procedures.
only four keys assigned to LEDs that ser- and accurate control even with critical or
ve as feedback for the pressed key and as very rapid thermal systems, engaging au-
guide to specify appropriate steps. tomatically when necessary.
DISPLAY AND KEYS

1. Temperature unit of measurement or number of program

running.
2. State of outputs OUT1, OU2, OUT3, OUT4.
3. Controller function states:
• RUN = setpoint programmer active;
• _/- = setpoint ramp active;
• TUN = PID parameters tuning active;
• MAN = manual/automatic (off = automatic control, on
1 = manual control);
9 • REM = remote setpoint enabled;
2 • SP1/2 = setpoint active (off = setpoint 1,
on = setpoint 2).
3 4. Work mode key (manual/automatic) in standard mode.
8
A function can be assigned via parameter but1.
7 The key is active only when the display shows the process
variable
5. Up/down keys: raise/lower the value of the parameter di-
splayed on the SV or PV display.
6. F key: lets you navigate among controller menus and para-
4 5 6 meters. Confirms the parameter value and selects the next
parameter.
7. Key pressed signals.
8. SV display: setpoint value, description of parameters, dia-
gnostics and alarm messages.
Configurable with parameter dS.SP (default = setpoint).
9. PV display: process variable, parameter values.

DIMENSIONS AND DRILLING TEMPLATE

70 mm
2.76 in

58 mm
2.28 in
48 mm
1.89 in
3.15 in
80 mm

2.76 in
70 mm
1.89 in
48 mm

45 - 0.0 mm
1.78 in
+0.6
0.39 in
10 mm

45 +0.6
- 0.0 mm

1.78 in

Dimensions mm/in
TECHNICAL DATA

OPERATOR INTERFACE
Type LCD black background
Screen area (L x H) 35 × 30 mm
Lighting Backlit with LEDs, life > 40,000 hours @ 25°C
PV display Number of digits: 4 to 7 segments, with decimal point
Digit height: 17 mm
Color: white or “custom”
SV display Number of digits: 5 to 14 segments, with decimal point
DISPLAY Digit height: 7.5 mm
Color: green or “custom”
Unit of measurement Selectable, °C, °F or custom 1
Color: same as PV display
Controller state signals Number: 6 (RUN, MAN, _/-, REM, SP1/2)
Color: amber
Output state signals Number: 4 (1, 2, 3, 4)
Color: red
Number of keys: 4 silicon (Man/Auto, INC, DEC, F)
KEYPAD
Type: mechanical
INPUTS
Sensor type TC, RTD (PT100, JPT100), DC linear sensor
Accuracy TC inputs:
Calibration accuracy: < +/- (0,25% of reading value in °C +0,1°C)
Linearization accuracy: 0,1% of reading value
Cold junction accuracy: < +/- 1,5°C a 25°C room temperature)
Cold junction compensation: > 30:1 rejection to the change of the room
temperature
RTD input:
Calibration accuracy: < +/- (0,15% of reading value in °C +1°C)
Temperature drift: < +/- (0,005% of reading value in °C +0,015°C )/°C
from 25°C room temperature
Linearization accuracy: 0,1% of reading value
Linear inputs:
Calibration accuracy:< 0,1% full scale
Temperature drift: < +/- 0,005% full scale /°C at 25°C room temperature
Sampling time 60 ms / 120 ms, selectable
MAIN INPUT
Digital filter 0,0...20,0 s
Temperature unit of measu- Degrees C / F, selectable from keypad
rement
Signal interval Type: linear
Scale: -1999...9999, settable decimal point
TC Thermocouple: J, K, R, S, T, C, D
(thermocouple) input Linearization: ITS90 or custom
RTD Resistance thermometer: PT100, JPT100
(resistance thermometer) Input impedance (Ri): ≥ 30 kΩ
input Linearization: DIN 43760 or custom
Max. line resistance: 20 Ω
DC linear input 0...60 mV input impedance (Ri): > 70 kΩ
0...1 V input impedance (Ri): > 15 kΩ
0...5 V / 0...10 V input impedance (Ri): > 30 kΩ
0/4...20 mA input impedance (Ri): 50 Ω
Linearization: linear or custom
Remote setpoint 0...1 V, 0...10 V, 0/4...20 mA
Scale 0...1 V input impedance (Ri): > 15 kΩ
AUXILIARY INPUT 0...10 V input impedance (Ri): > 30 kΩ
0/4...20 mA input impedance (Ri): 50 Ω
Accuracy 0,1% f.s. ±1 digit @25 °C
Type Isolated via external transformer
Number: 2 max
CT Max. capacity: x / 50 mA AC
(ammeter) Line frequency: 50/60 Hz
INPUT Input impedance (Ri): 10 Ω
Accuracy ±2% f.s. ±1 digit @25 °C

1) Programming is done with the GF_eXpress configuration program.

 Type voltage-free contact, or
NPN 24 V - 4,5 mA, or
PNP 12/24 V - max 3,6 mA
DIGITAL INPUTS (for detail see electrical connections)
Isolation 500 V
Number 3 max
OUTPUTS
Relay Number: 4 max
(R) Type of relay contact: NO
Max. current: 5 A, 250 VAC
Minimum load: 5 V, 10 mA
Life cycle: > 100.000 operations
Double isolation
Logic Number: 2 max
(D) Type: for solid-state relays
Voltage: 24 V ±10% (min 10 V @20 mA)
Isolated from main input
Triac ( long life relè) Number: 1 max
(T) Load: resistive
Voltage: 75...264 VAC
Current max: 1 A
Isolation 3 kV
snubber circuit integrated zero crossing switching
Continuous Number: 1 max
(C) Current: 4...20mA
Rout < 500 Ω
Resolution: 12 bit
Isolated from main input
Analog retransmission Number: 1 max
(A1) 0...10 V, max 20 mA, Rout: > 500 Ω
0...20 mA, 4...20 mA, Rout: < 500 Ω
Resolution: 12 bit
Isolated from main input
Number of alarm functions 4 max, assignable to an output
Possible configurations Maximum, minimum, symmetric, absolute/relative, exclusion at firing,
ALARMS
memory, reset from keypad and/or contact, LBA, HB
HBB Hold Back Band if enabled with Programmer function
CONTROL FUNCTIONS
Type Single loop
Control PID, ON/OFF, single action heat or cool, double action heat/cool
CONTROL Control output Continuous or ON/OFF
Cycle time: constant or optimized (BF)
Control output for motori- OPEN/CLOSE for floating motorized valve on Relay, Solid-state, Triac
zed valves outputs
Number of programs Max 4
Start / Stop / Reset / Skip via digital inputs and/or outputs from logic
operations
SETPOINT Output state: Run /Hold / Ready / End
PROGRAMMER Number of steps Max 12, each with own setpoint, ramp time and hold time
Times settable in HH:MM or MM:SS
Max 4 consents, configurable for ramp and for hold
Max 4 events, configurable in ramp and in hold
Number of setpoints Max 4, selectable from digital input
MULTIPLE
Each setpoint change is subject to set ramp, different for up and down
SETPOINTS
ramp
Function blocks Max 16, with 4 input variables per block.
LOGIC 1 The result can act on the state of the controller, of the programmer on
OPERATIONS alarms and outputs.
Each function contains an incorporated timer block timer.
Modes START / STOP
STABILIZATION (timer is on when PV enters a band set around setpoint;
TIMER FUNCTION at end of count you can activate an output, shut down SW or change
SP1/SP2)
FIRING (timed activation of control after power on)

1) Programming is done with the GF_eXpress configuration program.

 Calculation done on nominal line voltage and nominal load power or on
ENERGY COUNTER
rms current measured on load via CT
Short circuit or open circuit (LBA alarm)
DIAGNOSTIC Interrupted or partially interrupted load (HB alarm)
Short circuit of control output (SSR alarm)
Type EEPROM
RETENTIVE MEMORY
Max. number of writes 1.000.000
SERIAL INTERFACE
Type RS485
Baudrate 1200, 2400, 4800, 9600, 19.200, 38.400, 57.600, 115.200 bit/s
Protocoll MODBUS RTU
Isolated from main input
GENERAL DATA
Operating voltage 100...240 VAC/VDC ±10%, 50/60 Hz
(on request 20...27 VAC/VDC ±10%)
POWER SUPPLY Power dissipation 5 W max
Protections Overvoltage 300 V / 35 V
Connection Screw terminals and crimp connector, max. wire section 1 mm2
Serial configuration port Connector: microUSB
CONNECTIONS (for USB connection)
Inputs and outputs Screw terminals and crimp connector, max. wire section 2,5 mm2
Use Indoor
Altitudine 2,000 m max
AMBIENT
Operating temperature -10 ... +55 °C (as per IEC 68-2-14)
CONDITIONS
Storage temperature -20 ... +70 °C (as per IEC 68-2-14)
Relative humidity 20...85% RH non-condensing (as per IEC 68-2-3)
PROTECTION LEVEL IP 65 on front panel (as per IEC 68-2-3)
Positioning On panel, removable faceplate
ASSEMBLY Installation regulations Installation category: II; Pollution degree: 2
Isolation: double
DIMENSIONS 48 X 48 mm (1/16 DIN),
Depth: 80 mm
WEIGHT 0,16 kg
EMC Conforms to Directiv 2014/30/EU with reference to standard EN 61326-1
(electromagnetic compa- emission in industrial environment class A for models 650 LV
CE STANDARDS
tibility) emission in residential environment class B for models 650 HV
Safety: LVD Conforms to Directiv 2014/35/EU with reference to standard EN61010-1

ACCESSORIES

Code Description
F060800 Cable for programming with PC, USB-TTL 3 V with USB – microUSB connectors, length 1.8 m
F043958 “GF_eXpress” software CD
F060909 Configuration kit for new instruments GF_eXK-3-0-0
F060908 Portable configurator, complete with cable and Zapper
51968 Rubber gasket 48×48 front-box
51250 Fastening box to panel
51294 Protection of contacts at box bottom
51454 18 contacts at box bottom
330200 Current transformer (CT) 50/0.05 A
330201 Current transformer (CT) 25/0.05 A
CONNECTION DIAGRAM

NO NO
+ OUT 2 19 7 6 + +
OUT 2 C
- - -
OUT 1 (main)
C
OUT 3 20 8 5
C
NO +
~ OUT 4 21 9 4
5 V, 10 V
OUT 3
~ 22 10 3
C C
+ +
~ 23 11 2 T T
PWR
~ 24 12 1 - -
-

OPTIONS

B (Data +)
7 IN 2 7 7 +

A (Data -) A1
8 IN 1 8 RS485 8
-

9 COM 9 COM 9 COM

10 10 10 IN 1
CT1 current transformer CT1 current transformer
B (Data +)
11 11 11
CT2 second current CT2 second current
A (Data -)
12 transformer for 2-phase / 12 transformer for 2-phase / 12
3-phase load 3-phase load

B (Data +)
7 7 + 7 + SPR

A1
8
A (Data -) RS485 8
-
8 - SPR

9 COM 9 COM 9 COM

10 IN 3 10 IN 3 10 IN 3

11 IN 2 11 IN 2 11 IN 2

12 IN 1 12 IN 1 12 IN 1

LEGEND
NO
+
Isolated
~ digital - Logic output
PWR
Power supply Relay output
inputs C
~
B (Data +)
+
RS485 serial line
Linear input in A (Data -)
voltage / current +
C
- Thermocouple ~ Long-life solid state relay
input
~ output
-
Input for current +
transformer C DC analog output
Input -

+ SPR T
PT100
T +
JPT100
Remote Set-point A1 Isolated analog output
- SPR 2 / 3 wires -

! ATTENTION: For correct installation, read the warnings in the instruction manual.
ORDER METHODS

Ordering code 650 X - X - X X X - X X X X X- X X X

Model
Controller -
Programmer P
Valve V

Output 1
Relay R
Static D
Analog 4...20mA C

Output 2 - 3 - 4
1 Relay (5A) R-0-0
1 Static D-0-0
2 Relay (5A) R-R-0
1 Static + 1 relay D-R-0
1 Relay (5A) + 1 Long Life relay R-T-0
1 Static + 1 Long Life relay D-T-0
3 Relay (5A total) R-R-R

Remote Set Point - W retransmission -

CT inputs - Digital inputs -
Serial communication
Absent 0-0-0-0-0
CT1 0-0-1-0-0
CT1 + CT2 0-0-2-0-0
CT1 + 2 DI 0-0-1-2-0
CT1 + CT2+2 DI 0-0-2-2-0
CT1 + RS485 0-0-1-0-1
CT1 + CT2+RS485 0-0-2-0-1
3 DI 0-0-0-3-0
3 DI + RS485 0-0-0-3-1
3 DI + SPR 1-0-0-3-0
3 DI + W 0/4...20mA/0...10V 0-1-0-3-0
1 DI + W + RS485 0-1-0-1-1

Supply
20-27Vac/dc 0
100-240Vac 1

Functions
Logical operations LF

Display
Green setpoint G
Power supply 100...240 VAC
Inputs Outputs

Logic functions
Programmer
Code F Model Total Number of Outputs

Analog V/I
Analog I
Digital
Valves

RS485
Relay

Logic
Triac
SPR
CT
F060558 650-D-R00-00000-1-G 1 1
F059574 650-R-R00-00000-1-G 2 2 outputs
F060566 650-D-R00-00120-1-G 2 1 1 1
F060562 650-D-RR0-00000-1-G 2 1
F065788 650-R-RR0-00000-1-G 3
F065789 650-R-RT0-00000-1-G 2 1
F065790 650-D-RR0-00030-1-G 3 2 1
F060567 650-D-RR0-00200-1-G 2 2 1 3 outputs
F060564 650-C-RR0-00000-1-G 2 1
F060573 650-D-R00-01030-1-G 3 1 1 1
F065791 650-R-R00-01030-1-G 3 2 1
F060574 650-R-RR0-00101-1-G 1 3 •
F060563 650-D-RRR-00000-1-G 3 1
F065792 650-R-RRR-00000-1-G 4
F060575 650-D-RRR-00220-1LFG 2 2 3 1 •
F060576 650-D-RRR-00031-1LFG 3 3 1 • •
F065793 650-D-RRR-00201-1LFG 2 3 1 • •
F065794 650-D-RR0-01011-1LFG 1 2 1 1 • • 4 outputs
F060577 650-C-RRR-10030-1LFG 3 1 3 1 •
F060578 650V-R-RRR-00000-1-G • 4
F060561 650V-R-RRR-00030-1-G • 3 4
F060565 650P-D-RRR-00000-1-G • 3 1
F060560 650P-D-RRR-00030-1LFG • 3 3 1 •
F060579 650-D-RRR-01030-1LFG 3 3 1 1 • 5 outputs

Power supply 20...27 VAC/VDC

Inputs Outputs

Logic functions
Programmer

Code F Model Total Number of Outputs

Analog V/I
Analog I
Digital
Valves

RS485
Relay

Logic
Triac
SPR
CT

F065795 650-D-R00-00000-0-G 1 1
F065796 650-R-R00-00000-0-G 2 2 outputs
F065797 650-D-R00-00120-0-G 2 1 1 1
F065798 650-D-RR0-00000-0-G 2 1
F065799 650-R-RR0-00000-0-G 3
F065800 650-R-RT0-00000-0-G 2 1
F065801 650-D-RR0-00030-0-G 3 2 1
F065802 650-D-RR0-00200-0-G 2 2 1 3 outputs
F065803 650-C-RR0-00000-0-G 2 1
F065804 650-D-R00-01030-0-G 3 1 1 1
F065805 650-R-R00-01030-0-G 3 2 1
F065806 650-R-RR0-00101-0-G 1 3 •
F065807 650-D-RRR-00000-0-G 3 1
F065808 650-R-RRR-00000-0-G 4
F065809 650-D-RRR-00220-0LFG 2 2 3 1 •
F065810 650-D-RRR-00031-0LFG 3 3 1 • •
F065811 650-D-RRR-00201-0LFG 2 3 1 • •
F065812 650-D-RR0-01011-0LFG 1 2 1 1 • • 4 outputs
F065813 650-C-RRR-10030-0LFG 3 1 3 1 •
F065818 650V-R-RRR-00000-0-G • 4
F065819 650V-R-RRR-00030-0-G • 3 4
F065820 650P-D-RRR-00000-0-G • 3 1
F065821 650P-D-RRR-00030-0LFG • 3 3 1 •
F065822 650-D-RRR-01030-0LFG 3 3 1 1 • 5 outputs

Please contact GEFRAN for information on available codes.

 Conformity TC N° RUД-IT.AЛ32.b.01762

FM FM approvals project NO: 0003054712

UL Conformity C/UL/US File no. E216851

EMC (electromagnetic compatibility): conforms to directive 2014/30/EU with reference to standard EN 61326-1
emission in industrial environment class A for models 650 LV
emission in residential environment class B for models 650 HV
Safety LVD: conforms to directive 2014/35/EU with reference to standard EN61010-1

GEFRAN spa via Sebina,74 - 25050 Provaglio d’Iseo (BS)

Tel. 03098881 - fax 0309539063 - Internet: http://www.gefran.com DTS_650_07-2018_ENG