range, or would shorten the sensor life. 9.

In order to keep the detector accuracy, it's

8. If the detection gas such as mixed better to check every half a year, and calibrate
combustible gas, liquid steam etc. which is every year.
High Quality European based Manufacturers different with calibration gas, there it would be
certain error between testing results and actually
BS-658 Waterproof CO Detector with double connection gas concentration.

TECHNICAL CHARACTERISTICS
OPERATION VOLTAGE 24V + 25%
MAXIMUM POWER CONSUMPTION 2W / Chanel
DETECTING GAS CO
DETECTING RANGE 0-1000ppm
RESOLUTION 1ppm
LOW ALARM LEVEL 35ppm
HIGH ALARM LEVEL 200ppm
SIGNAL OUTPUT low alarm relay / high alarm relay output
CABLE 1.5mm 2 x 4 cables
DEGREES OF COVER PROTECTION IP 66
RESPONSE TIME <60sec
o
OPERATION TEMPERATURE RANGE -20 to 50 C
RELATIVE HUMIDITY Up to 95%
EXTERNAL DIMENSIONS LxBxH 165x118x62
TYPICAL WEIGHT 330gr

Thank you for purchasing this product of transmitter structure dimensions and then install
Olympia Electronics. A European manufacturer. the transmitter using 3pcs of M6*20 bulge bolts. 1.Wall
4.3 Wire connection 2. Detector
1.Brief introduction The wire between gas controller and the detector 3. Locknut
should be more than 1.5 mm2 (>1000m). 4. Wire
With a high-quality electrochemical gas sensor
After the detector is installed correctly according 5. Bulgy bolt
and excellent craft work, it has the advantages
of good repeatability, Resistant against to the above methods (4.1), open the up-cover of
temperature and humidity, long life-span and the detector and screw off the locknut. Pull the
easy operation. cables into the detector through the lock
It can convert the gas concentration in the air to connector. Then connect the wire to the terminals
a digital signal output with a range of 4-20mA. It of the detector according to the marks on the
is suitable for gas detection in car parkings or circuit. The connection is as shown in the
industrial environment where toxic gas leaks. following sketch map. Please pay attention to the
2. Instruction on installation and wire correspondence of the wires. After connecting Sketch Map 2 Terminal Instruction:
connection wires correctly, pull out the extra cables and L-ALARM: Low alarm relay output (35ppm)
4.1 Installation position screw on the locknut, tighten the rubber air-proof H-ALARM: High alarm relay output (200ppm)
4.1.1 Please install the gas detector within 1 circle and clasp the cables. After all connections +: Power supply from panel 24V DC
meter near to the gas valve, pipeline connector, are correct, fix the up-cover with M4*8 bolts. - : Power supply from panel 24V DC
gas output mouth or easily leakage point. According to the spot condition, you can also first
Please keep it far away from high temperature connect the wires and then install the detector.

H-ALARM

H-ALARM
L-ALARM

L-ALARM
and humidity.
4.1.2 Installation height: 1.5m above the ground. Notices BS-658 BS-658
4.1.3 If installed in large areas, installation of 1. Do not use the detector in the explosive
1pc every 10-12 square meters can also have environment.
- -

+
}
}

}
}
good detection results. 2. Avoid dropping it from higher place or shaking
4.1.4 When installing it, please ensure the gas it acutely.
sensor head is pointed downward, the locknut 3. Please avoid colliding the electric circuit and

+
24V DC
screwed completely and well covered. the detector during installation.
4. The user is not allowed to replace any part of
from panel -
4.2 Installation method the detector freely. 470Ω/0,5W Included 470Ω/0,5W
Please choose the places without corrosive gas, 5. Please avoid installing it on the heat source
lampblack, dust and avoid water logging etc in nor shaking source. From panel`s
the detection field. Please refer to the suitable 6. Avoid fast flowing gas passed the sensor zone +
-
installation method as follows: directly, otherwise it would effect the testing
result. Terminal
Method (Wall-mounted): If the user needs to resistor
install the detector on the wall, please choose 7. Do not use the transmitter in high gas
an appropriate surface according to the concentration much higher than its detection Connecting the L-ALARM outputs of two detectors to a panel

Page 1 from 2 980165800_09_006 Page 2 from 2 980165800_09_006

 range, or would shorten the sensor life. 9. In order to keep the detector accuracy, it's
8. If the detection gas such as mixed better to check every half a year, and calibrate
combustible gas, liquid steam etc. which is every year.
High Quality European based Manufacturers different with calibration gas, there it would be
certain error between testing results and actually
BS-658 Waterproof CO Detector with double connection gas concentration.

TECHNICAL CHARACTERISTICS
OPERATION VOLTAGE 24V + 25%
MAXIMUM POWER CONSUMPTION 2W / Chanel
DETECTING GAS CO
DETECTING RANGE 0-1000ppm
RESOLUTION 1ppm
LOW ALARM LEVEL 35ppm
HIGH ALARM LEVEL 200ppm
SIGNAL OUTPUT low alarm relay / high alarm relay output
CABLE 1.5mm 2 x 4 cables
DEGREES OF COVER PROTECTION IP 66
RESPONSE TIME <60sec
o
OPERATION TEMPERATURE RANGE -20 to 50 C
RELATIVE HUMIDITY Up to 95%
EXTERNAL DIMENSIONS LxBxH 165x118x62
TYPICAL WEIGHT 330gr

Thank you for purchasing this product of transmitter structure dimensions and then install
Olympia Electronics. A European manufacturer. the transmitter using 3pcs of M6*20 bulge bolts. 1.Wall
4.3 Wire connection 2. Detector
1.Brief introduction The wire between gas controller and the detector 3. Locknut
should be more than 1.5 mm2 (>1000m). 4. Wire
With a high-quality electrochemical gas sensor
After the detector is installed correctly according 5. Bulgy bolt
and excellent craft work, it has the advantages
of good repeatability, Resistant against to the above methods (4.1), open the up-cover of
temperature and humidity, long life-span and the detector and screw off the locknut. Pull the
easy operation. cables into the detector through the lock
It can convert the gas concentration in the air to connector. Then connect the wire to the terminals
a digital signal output with a range of 4-20mA. It of the detector according to the marks on the
is suitable for gas detection in car parkings or circuit. The connection is as shown in the
industrial environment where toxic gas leaks. following sketch map. Please pay attention to the
2. Instruction on installation and wire correspondence of the wires. After connecting Sketch Map 2 Terminal Instruction:
connection wires correctly, pull out the extra cables and L-ALARM: Low alarm relay output (35ppm)
4.1 Installation position screw on the locknut, tighten the rubber air-proof H-ALARM: High alarm relay output (200ppm)
4.1.1 Please install the gas detector within 1 circle and clasp the cables. After all connections +: Power supply from panel 24V DC
meter near to the gas valve, pipeline connector, are correct, fix the up-cover with M4*8 bolts. - : Power supply from panel 24V DC
gas output mouth or easily leakage point. According to the spot condition, you can also first
Please keep it far away from high temperature connect the wires and then install the detector.

H-ALARM

H-ALARM
L-ALARM

L-ALARM
and humidity.
4.1.2 Installation height: 1.5m above the ground. Notices BS-658 BS-658
4.1.3 If installed in large areas, installation of 1. Do not use the detector in the explosive
1pc every 10-12 square meters can also have environment.
- -

+
}
}

}
}
good detection results. 2. Avoid dropping it from higher place or shaking
4.1.4 When installing it, please ensure the gas it acutely.
sensor head is pointed downward, the locknut 3. Please avoid colliding the electric circuit and

+
24V DC
screwed completely and well covered. the detector during installation.
4. The user is not allowed to replace any part of
from panel -
4.2 Installation method the detector freely. 470Ω/0,5W Included 470Ω/0,5W
Please choose the places without corrosive gas, 5. Please avoid installing it on the heat source
lampblack, dust and avoid water logging etc in nor shaking source. From panel`s
the detection field. Please refer to the suitable 6. Avoid fast flowing gas passed the sensor zone +
-
installation method as follows: directly, otherwise it would effect the testing
result. Terminal
Method (Wall-mounted): If the user needs to resistor
install the detector on the wall, please choose 7. Do not use the transmitter in high gas
an appropriate surface according to the concentration much higher than its detection Connecting the L-ALARM outputs of two detectors to a panel

Page 1 from 2 980165800_09_006 Page 2 from 2 980165800_09_006