Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

SUZO Hopper: August 99 6501 0760

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

SUZO Hopper

Technical specifications

• Suitable for coins or tokens from 17mm - 40mm


• Counts approximately 300 coins (25mm) per
minute
• Capacity of 1000 coins (25mm) standard model
• Capacity of 2000 coins (25mm) extended bowl
• Operating voltage: 24 VDC
After service or repair to the

Suzo D-AMP
Hopper it should be thoroughly
checked in the Hopper Out
test routine of the machine.

Hopper removal (replacement) • Open the Main Door.

For service or repair, remove the Hopper from the • Remove the Coin Bowl Assy.
machine.
• Grip the hopper handle with
the left hand and with the
thumb pointing downwards,
press the Hopper securing
clip and slide the Hopper out-
wards.

August 99
6501 0760 1
High Level Sensor Adjustment

The coin bowl of the Suzo Hopper is spring mounted.


The weight of the coins, determines at which point
the level switch is activated.

• Fill the bowl with the appro-


priate amount of coins

• Slowly turn the adjustment


screw clockwise until the lev-
el switch is activated in the

Suzo D-AMP
down position.

Hopper Knife Adjustment

The front surface of the Hopper Knife should be flush


to the Pin Wheel and lay gently on the Shelf Wheel.

• Adjustment is made by
loosening the 2 screws and
correcting the alignment of
the Knife.

Note:
Do not use oil or grease in the
coin handling area.

August 99
2
Coin Switch Adjustment

The coin switch registers all paid out coins and sends • When the roller is in the neu-
the information to the Master Board. tral position (no coin touch-
ing the roller), the coin
switch should be open.

• Place a coin on the Pin Wheel


underneath the roller. The
coin switch should close
when the roller moves up-
wards.

• Move the coin to the coin out

Suzo D-AMP
channel. The switch should
close again as the coin leaves
the roller.

Coin Wiper Adjustment

The Coin Wiper singles out the coins, this prohibits • Lay a coin beneath the Wip-
coin jamming. er.

• Loosen both screws and ad-


just the Wiper so that it is
lightly brushing the surface
of the coin.

• Tighten alternately both


screws checking that the
alignment is still correct.

Note:
The Wiper should guide and not
hold the coin.

August 99
3
Coin Switch Test

Testing of the coin switch and the High Level Sensor is • Remove hopper
easily done, by using a multimeter
• Switch multimeter to OHM

• Connect multimeter as
shown

• If the coin switch is not acti-


vated you should measure
the internal resistance of the
switch.

Suzo D-AMP
• Activate the coin switch, dur-
ing measurement the resis-
tance will change to "0" Ω.

Note:
The Level Switch is tested in the
same way.

If you have no Multimeter to hand you can test the • Enter Service Menu
function of all the switches in the Selftest of the
machine. • Call up Self Test

• Call up Switch Test


Service Menu
SELF TEST
LAST 5 GAMES
LAST 5 BILLS
• The current status of the
LAST TICKETS
MENUE SETUP
SET CLOCK
switches can be seen on the
HOPPER OUT
PC SETUP
monitor.
MAIN VERSION: xxxxxxx
GRAFIC VERSION: xxxxxx
LT31 CC16 Self Test
IIC - PORT DRIVER CHECK
• Operating the switches by
VOLTAGE CHECK
COIN DIVERTER CHECK hand should change the sta-
CANDLE TEST
DIPSWITCH SETTINGS
SOUND TEST Switch Test tus on the monitor.
LAMP TEST
SERIAL I/O TEST
SWITCH TEST
OPTOBOARD TEST
HANDLE TEST
BUTTON TEST
MONITOR MAGNETIC STATE
RGB- COLOUR TEST
CHECKSUM
MAIN COMMBOARD TEST
C-BOARD TEST
C-BOARD TEST (ERROR REPEAT)
QUIT

August 99
4
Suzo D-AMP

August 99
5
POS Part-No Nomenclature
1 BP6311-8 platform bracket 54 BSP100-309 spring
2 BP6312-14 left side bracket 55 BP845 wiper
3 22-0750-2 micro switch 56 BP2495 scoop ext.
4 BP126-729 tension clip 57 BP834 liner
9 BP6264-120 handle 58 BP2540-4 coin baffle
14 BP6312-11 right side bracket 59 BP2450-5 coin baffle
15 211759-1 AMP connector 60 BP6717-16 inlet slide
18 BP6442-264 switch bracket 61 BC841-4 end cap
19 22-0715 micro switch
20 BP6665-709 switch stop bracket
21 BP843-1 pivot bracket
22 BP840 spring mount
23 BSP200-192 spring

Suzo D-AMP
24 BC840-1 wheel housing
25 BE119-520 motor 24VDC
BS231-827-1 mounting bushing
648-022-132 mounting screw
26 BP839 coin deflector
27 BP846 knife metal
BP846-100 knife nylon
28 BP838 outlet cover
30 150-025-702 screw hx hd
1050-052 nut
31 199-025-040 set screw 10x25
33 BM1689-100 bearing
BS1071-194-100 bearing pin
34 BP842-3 pin wheel 12 pin
35 BS231-827-1 bushing
648-016-222 1032-1110 screw
36 BP847-xx specify coin
37 BS2200 pilot bushing
38 BR526S agitator
39 BS231-825 bushing
41 BP8195 spring liner
42 BC841-3 hopper casting
43 BSP200-191 spring
44 BS2109-1 spring mount
45 BP200-191 spring
46 BP2452 scoop supp.brkt
47 BS2119 exentric mounting
48 BA2893-6 pivot roller assy
49 BS231-914 spacer
50 BS1071-195 dowel pin
51 150-008-040-1 set screw
52 BSP100-326 spring
53 BS2018 pivot rod

August 99
6

You might also like