Professional Documents
Culture Documents
General Guide ................................................. 3
General Guide ................................................. 3
3
Turning on or off............................................. 3
Battery replacement ....................................... 3
Auto power-off function ................................. 3
Reset operation .............................................. 3
Contrast adjustment ....................................... 3
Display readout .............................................. 4
E–1
Function Table...............................................17
E–2
Battery replacement
SR-270X is a dual power system which is powered by one
button-type battery (G13 or L1154) and a solar cell. If the display
becomes dim and difficult to read, the batteries should be replaced
as soon as possible.
To replace batteries:
1) Remove the screw and the battery compartment cover.
2) Remove the old battery and insert a new one with polarity in
correct directions, then replace the cover.
3) After changing battery, please use a pointed object to press the
reset hole in the rating label area located at the rear of this unit.
Reset operation
If the calculator is on but you get unexpected results, press [ 2nd ]
[ CLR ] in sequence. A message appears on the display to confirm
whether you want to reset the calculator and clear memory contents
after selecting [ 3 ].
Contrast adjustment
Pressing the [ W ] or [ X ] following [ 2nd ] [ SET UP ] [ T ] [ 5 ]
(WCONTX) keys in sequence can make the contrast of the screen
lighter or darker. Holding either key down will make the display
become respectively lighter or darker. After finishing your setting,
press [ AC ] to exit.
E–3
M at h D
c Indicator
Entry line 12369x7532 x1 0 32
9 . 31 6 3 30 8 x1039 Result line
E–5
Replay function
This function stores operations that just have been executed in
COMP mode. After execution is completed, pressing [ T ] or [ S ]
key will display the operation executed.
You can continue moving the cursor by [ W ] or [ X] to display
previous input steps and editing values or commands for
subsequent execution.
The operation records in Memory are cleared each time when you
turn off the calculator, press [ ON ] key, perform a “reset”, change
display format or calculation mode.
When the memory is full, the oldest calculation records are deleted
automatically to make room for the new ones. See Example 4.
E–6
Running memory
You should keep the following rules in mind when using running
memory. See Example 6.
• Press [ M+ ] to add a result to running memory and the " M "
indicator appears when a number is stored in the memory. Press
[ RCL ] [ M ] to recall the content of running memory.
• Recalling from running memory by pressing [ RCL ] [ M ] key does
not affect its contents .
• Running memory is not available when you are in statistics mode.
• The memory variable M and running memory utilize the same
memory area.
• In order to replace the content of the memory with the displayed
number, please press [ 2nd ] [ STO ] [ M ] key.
• To clear the content of running memory, you can press [ 0 ] [ 2nd ]
[ STO ] [ M ] in sequence.
(Note) : Besides pressing [ 2nd ] [ STO ] [ M ] key to store a value,
you can also assign values to memory variable M by
[ M+ ]. However, when [ 2nd ] [ STO ] [ M ] is used,
previous memory contents stored in variable M are
cleared and replaced with the newly assigned value.
When [ M+ ] is used, values is added to present sum in
memory.
Order of operations
Each calculation is performed from left to right and in the following
order of precedence:
1) Expression inside parentheses.
2) Functions with parentheses:
P R, R P
–1 –1 –1 –1
sin, cos, tan, sin , cos , tan , sinh, cosh, tanh, sinh ,
–1 –1
cosh , tanh ,
X X
log, ln, √, 3 , 10 , e , Abs, RND
E–7
E–8
P R 0 ≦ r < 1 x 10 100
θ: same as sin x
DMS │D│, M, S < 1 x 10 100, 0 ≦ M, S
eDMS x < 1 x 10 100
Decimal Q Sexagesimal Conversions
0
0 ׀0 ≦ ׀׀ x ≦ 9999999
59 ׀59 ׀ ׀
100
xy x > 0 : –1 x 10 < y log x < 100
x=0:y>0
x < 0 : y = n, m/(2n+1) (m, n are integers)
but –1 x 10 100 < y log ⏐x⏐ < 100
x y 1
y > 0 : x ≠ 0, –1 x 10 100 < log y < 100
x
y=0:x>0
y < 0 : x = 2n+1, (2n+1)/m (m≠0, m, n are
integers)
1
but –1 x 10 100 < log ⏐y⏐ < 100
x
A b/c Total of integer, numerator and denominator
must be within 10 digits (includes division
marks)
STAT 1–VAR :
a. n ≦ 80 lines (when FREQ column is OFF)
b. n ≦ 40 lines (when FREQ column is ON)
2–VAR :
a. n ≦ 40 lines (when FREQ column is OFF)
b. n ≦ 26 lines (when FREQ column is ON)
Error conditions
Error message will appear on the display and further calculation
becomes impossible when any of the following conditions occur.
Indicator Meanings
Math ERROR (1) You attempted to divide by 0
(2) When allowable input range of function
calculations exceeds the range specified
E–9
Basic Calculations
Use COMP ( [ MODE ] 1 ( COMP ) ) mode for basic calculations.
Arithmetic calculation
Arithmetic operations are performed by pressing the keys in the
same sequence as in the expression. See Example 7.
For negative values, press [ (–) ] before entering the value.; You can
x
enter a number in mantissa and exponent form by [ x10 ] key. See
Example 8.
10 –9
Results equal to or greater than 10 or results less than 10 are
displayed in exponential form. See Example 9.
Parentheses calculations
Operations inside parentheses are always executed first. SR-270X
Math mode can use up to 24 levels and Linear mode can use up to
25 levels of consecutive parentheses in a single calculation.
Closed parentheses occurring immediately after operation of the [ ) ]
key may be omitted, no matter how many are required. See Example
10.
(Note) : A multiplication sign " x " occurring immediately before
an open parenthesis can be omitted.
The correct result cannot be derived by entering [ ( ] 2 [ + ] 3 [ ) ]
x x
[ x10 ] 2. Be sure to enter [ x ] between the [ ) ] and [ x10 ] in
Example 11.
E – 10
Display notations
The calculator has the following display notations for the display
value. See Example 14.
Fixed Decimal Point Notation
To specify the number of decimal places, press [ 2nd ] [ SET UP ]
[ 6 ] and then a value indicating the number of places ( 0~9 ). Values
are displayed rounded off to the place specified.
Scientific Notation
Scientific notation expresses numbers with one digit to the left of the
decimal and the appropriate power of 10.
To select scientific notation, press [ 2nd ] [ SET UP ] [ 7 ], and then a
value (0~9) to specify the number of decimal digits. Values are
displayed rounded off to the place specified.
Norm Notation
Press [ 2nd ] [ SET UP ] [ 8 ] and then select Norm1 (the default) or
Norm2 to determine the range to display the result in
non-exponential format (within the range) or in exponential format
(out of the range).
Norm1: x < 10 -2, x ≧10 10
-9
Norm2: x < 10 , x ≧10 10
Engineering Notation
Pressing [ ENG ] or [ 2nd ] [ eENG ] will cause the exponent display
for the number being displayed to change in multiples of 3.
Answer Function
Answer function stores the most recently calculated result. It is
retained even after the power is turned off. Once a numeric value or
numeric expression is entered and [ M+ ], [ 2nd ] [ M– ], [ RCL ],
[ 2nd ] [ STO ] or [ = ] is pressed, the result is stored by this function.
See Example 15.
(Note) : Even if execution of a calculation results in an error,
however, Answer memory retains its current value.
E – 11
Fraction calculation
Fraction value display is as follows:
Improper Fraction Mixed Fraction
12 5
Math format: 56
5 12
Linear format: 12 」5 56 」5 」12
(Note) : Values are automatically displayed in decimal format
whenever the total number of digits of a fractional value
( integer + numerator + denominator + separator marks )
exceeds 10.
In Linear mode, to enter a mixed number, enter the integer part,
press [ d/e ], enter the numerator, press [ d/e ], and enter the
denominator ; To enter an improper fraction, enter the numerator,
press [ d/e ], and enter the denominator. See Example 18.
During a fraction calculation, if the figure is reducible, a figure is
reduced to the lowest terms after pressing the [ = ] key. The initial
default for a fraction result is improper fraction. By pressing [ 2nd ]
[ A b/c_`d/e ], the displayed value will be converted to the mixed
fraction and vice versa. To convert between a decimal and fractional
result, press [ F_`D ]. See Example 19.
Calculations containing both fractions and decimals are calculated in
decimal format. See Example 20.
E – 12
Coordinates transformation
Rectangular Coordinates Polar Coordinates
x + y i = r (cosθ+ i sinθ)
(Note) : When using those keys, make sure the calculator is set
for the angle unit you want.
The calculator can perform the conversion between rectangular
coordinates and polar coordinates by [ 2nd ] [ P R ] and [ 2nd ]
[ R P ]. See Example 29~30.
Probability
This calculator provides the following probability functions (See
Example 31~34.):
[ nPr ] Calculates the number of possible permutations of n item
taken r at a time.
E – 13
Other functions ( √, 3
, X
, x-1, x2, x3, xy , Abs,
RND )
-1
The calculator also provides reciprocal ( [ x ] ), square root ( [ √ ] ),
cubic root ( [ 2nd ] [ 3 ] ), universal root ( [ 2nd ] [ X ] ), square
2 3 y
( [ x ] ), cubic ( [ x ] ), and exponentiation ( [ x ] ) functions. See
Example 35~39.
Multi-statement Function
A Multi-statement is a number of individual statements grouped
together by display result commands (:) for sequential execution.
When execution reaches the end of a statement followed by (:),
execution stops and an intermediate result with a " Disp " icon
appears on the display. You can resume execution by pressing [ = ].
" Disp " icon disappears when the last statement is being executed.
See Example 40.
Statistical Calculations
Use STAT ( [ MODE ] 2 ( STAT ) ) mode for statistical calculations.
When you enter STAT mode, you are taken to the STAT menu with
a choice of eight calculation types as follows:
Single–variable statistics
1: 1–VAR Single-variable statistics
Paired-variable / Regression statistics
2: A+BX Linear Regression Y = A + BX
2 2
3: _+CX Quadratic Regression Y = A + BX + CX
4: ln X Logarithmic Regression Y = A + B lnX
BX
5: e^X e Exponential Regression Y=A•e
X
6: A•B^X ab Exponential Regression Y=A•B
B
7: A•X^B Power Regression Y=A•X
8: 1/X Inverse Regression Y=A+B/X
E – 14
E – 15
E – 16
You also can add a new data anytime. The unit automatically
recalculates statistics each time you press [ = ] and enter a new data
value.
Function Table
Use TABLE ( [ MODE ] 3 ( TABLE ) ) mode for generation of a
function table.
TABLE mode lets you define a function and express it in a tabular
form. To set up a function table, you need to: (See Example 42.)
1. Press [ MODE ] [3] (TABLE)
2. Enter a function, and press [ = ]
3. Input the Start, End, and Step value of X, and press [ = ]
4. After Step 3, a table of values that consists of each input, X, and
its corresponding output, f(X), is generated.
(Note) : 1. Only the variable X is available to be used in a
function.
2. The Start, End, and Step value you specify should
produce a table not exceed a maximum of 30 X-values.
E – 17