Desmodur TDL6xx XL1705

DESMODUR® TDL6xx + BAYTEC® XL 1705 68 to 95 Shore A
NATURE OF COMPONENTS
Prepolymer nature Nature of chain extender and other components
TDI - Adipate BAYTEC® XL 1705 Amine chain extender
CHARACTERISTICS OF COMPONENTS
DESMODUR® DESMODUR® DESMODUR® DESMODUR® BAYTEC® XL
Unit DESMODUR® TDL626
TDL630 TDL639 TDL645 TDL653 1705
2.60 3.15 3.85 4.25 5.05
% NCO % -
(± 0.2) (± 0.2) (± 0.2) (± 0.2) (± 0.2)
Physical appearance at room temperature - solid solid solid solid solid liquid
Processing temperature °C 80 80 80 80 80 30
Viscosity at processing temperature cps 1900 1300 800 1100 1050 690
Specific gravity at processing temperature - 1.20 1.20 1.20 1.20 1.20 1.21
ELASTOMER TYPICAL PROPERTIES (DATA GIVEN AS AN INDICATION)

Prepolymer DESMODUR® TDL626 DESMODUR® TDL630 DESMODUR® TDL639 DESMODUR® TDL645 DESMODUR® TDL653
Chain extender BAYTEC® XL 1705 BAYTEC® XL 1705 BAYTEC® XL 1705 BAYTEC® XL 1705 BAYTEC® XL 1705
Hardness at 20°C DIN 53505 Shore 68 A * 75 A * 80 A 85 A 95 A
10% Modulus DIN 53504 MPa 1.0 1.5 2.2 2.7 6.5
100% Modulus DIN 53504 MPa 3.0 4.5 5.8 6.1 9.4
200% Modulus DIN 53504 MPa 4.1 6.1 7.8 8.3 11.8
300% Modulus DIN 53504 MPa 5.9 9.0 11.3 12.1 16.6
Tensile strength DIN 53504 MPa 46 50 55 54 52
Elongation DIN 53504 % 720 615 610 570 550
Tear strength : without nick ISO 34-1 kN/m 74 89 100 98 125
Tear strength : with nick ISO 34-1 kN/m 52 59 70 75 88
Resilience DIN 53512 % 49 45 35 27 33
Abrasion loss ISO 4649 mm³ 75 75 85 95 115
Compression set (deflection / 22 h / 70 °C) ISO 815- 1 % 28 23 28 35 49
Hardness at -5°C DIN 53505 Shore 72 A 82 A 88 A 93 A 98 A
Hardness at 80°C DIN 53505 Shore 63 A 70 A 77 A 78A 88 A
Specific gravity 1.22 1.22 1.23 1.23 1.24
(*) depending on process conditions, curing and post curing temperature, hardness may vary from ± 3 Shore A.
Labelling : This system data sheet is only valid in combination with the corresponding components current safety data sheets ! Any updating of safety relevant information – in accordance with EU directives – will only be reflected in the
Safety Data Sheets, copies of which will be revised and distributed. For further technical information relating to safety, the Safety Data Sheets should be consulted.
Covestro Elastomers SAS- 46, avenue des Allobroges - BP 116 - 26103 Romans cedex - France - Tel. 33 (0)4 75 72 72 75 - Fax 33 (0)4 75 02 11 73 – E-mail: info.elastomers@covestro.com – www.elastomers.covestro.com
Covestro Elastomers SAS est certifié ISO 9001 : 2008
Version 07
DESMODUR® TDL6xx + BAYTEC® XL 1705 68 to 95 Shore A
STORAGE AND USE PRECAUTIONS

DESMODUR® DESMODUR® DESMODUR® DESMODUR® DESMODUR®
Unit BAYTEC® XL 1705
TDL626 TDL630 TDL639 TDL645 TDL653
Optimal storage temperature of the drums °C < 30 < 30 < 30 < 30 < 30 < 30
Storage time (sealed drum) Month 6 6 6 6 6 12
PREPARATION BEFORE PROCESSING
Preheating time / preheating temperature hr / °C 24 / 70 -
Homogenization before processing required - no no no no no no
Degassing required - yes yes yes yes yes yes
Keep from heat and protect against moisture.
PROCESSING
Prepolymer DESMODUR® TDL626 DESMODUR® TDL630 DESMODUR® TDL639 DESMODUR® TDL645 DESMODUR® TDL653
® ® ®
Chain extender BAYTEC ®
XL 1705 BAYTEC XL 1705 BAYTEC XL 1705 BAYTEC XL 1705 BAYTEC® XL 1705
Hardness Shore 68 A * 75 A * 80 A 85 A 95 A
Prepolymer processing temperature °C 80
BAYTEC® XL 1705 processing temperature °C 30
Parts by weight of prepolymer 100 100 100 100 100
Parts by weight of BAYTEC® XL 1705 6.3 7.6 9.3 10.3 12.2
MOLDING AND CURING
Mold temperature °C 100
Pot life (400g mixture) min 13’ 8’ 4’ 6’ 4’
Demolding time min 45’ 35’ 30’ 30’ 20’
Post-curing hr / °C 16 / 110
(*) depending on process conditions, curing and post curing temperature, hardness may vary from ± 3 Shore A.
Use of degassing agent is recommended for hand casting.
A one week aging at room temperature is required to obtain the optimal properties of the elastomer.
The following information and our technical advice – whether verbal, in writing or by way of trials – are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Our advice
does not release you from the obligation to check its validity and to test our products as to their suitability for the intended processes and uses. The application, use and processing of our products and the products manufactured by
you on the basis of our technical advice are beyond our control and, therefore, entirely your own responsibility. Our advice concerning safety does not release you from the obligation to determine the safety measures designed for
your production environment, that we may not be able to anticipate, to check abilities and to inform the people who will use, handle or be in contact with these products.
Covestro Elastomers SAS- 46, avenue des Allobroges - BP 116 - 26103 Romans cedex - France - Tel. 33 (0)4 75 72 72 75 - Fax 33 (0)4 75 02 11 73 – E-mail: info.elastomers@covestro.com – www.elastomers.covestro.com
Covestro Elastomers SAS est certifié ISO 9001 : 2008
Version 07

Desmodur TDL6xx XL1705

Uploaded by

Copyright:

Available Formats

Desmodur TDL6xx XL1705

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Desmodur TDL6xx XL1705

Uploaded by

Copyright:

Available Formats

DESMODUR® TDL6xx + BAYTEC® XL 1705 68 to 95 Shore A

ELASTOMER TYPICAL PROPERTIES (DATA GIVEN AS AN INDICATION)

STORAGE AND USE PRECAUTIONS

Keep from heat and protect against moisture.

You might also like