Users Manual KD21C KDS
Users Manual KD21C KDS
Users Manual KD21C KDS
◆Color categories
The cover of the display is two color options, black and white, and
down shell of the display is only one black.
Assembly
The KD21C display should be mounted on the left handlebar of the
Ebike at a comfortable angle. Cut off the power supply before connecting
the display to the controller.
◆Button Definition
General Operation
◆Switching the E-bike System On/Off
To switch on the E-bike system, hold the MODE button for 2s.
In the same way to hold the MODE button for 2s again, the E-bike
system will be switched off.
When switching off the E-bike system the leakage current is less
than 1 uA.
■When parking the E-bike for more than 10 minutes, the E-bike
system switches off automatically.
◆Display Interface
After switching on the E-bike system, the display shows current
speed and total distance except battery indicator and assistance level.
To change the indicated information, press the MODE button to
show in turn as follows: Current Speed (Km/h) → Trip Distance (Km)
→Trip Time (Hour) → Maximum Speed (Km/h) → Average Speed
(Km/h) → Motor-output (W) →Current Speed (Km/h).
3
always, the E-bike will go on at a uniform speed of 6 Km/h, “P” is
showed on the screen at the same time. The push-assistance function
switches off as soon as you release the DOWN button.
Push-assistance Mode
■Push-assistance function may only be used when pushing the E-
bike. Danger of injury when the wheels of the E-bike do not have
ground contact while using the push-assistance function.
◆Battery Indicator
The five battery bars represent the capacity of the battery. When the
battery is in low voltage, battery frame will flash to notice that the battery
needs to be recharged immediately.
5
Error Code Indication
■When an error code appears, please refer to an authorized E-bike
dealer .
General Settings
After the E-bike system is switched on, to access general settings
menu, hold both the UP and DOWN button for 2s.
■All the Settings are operated in the case of parking the E-bike.
◆Trip Distance Clearance
TC represents trip distance clearance setting.
To clear trip distance, press the UP/DOWN button to choose Y or N.
The default value is N.
To store a changed setting, press the MODE button and then
access backlight contrast settings.
Various symbol definitions please refer to Attached list 4.
◆Speed-limit Settings
LS represents the speed limit settings. When the current speed is
faster than speed limit, the E-bike system will switch off automatically.
Speed limit ranges from 12Km/h to 40Km/h. The default value is 25Km/h.
To change basic settings, press the UP/DOWN button to increase or
decrease until the desired value is displayed.
Hold the MODE button for 2s and then exit General Parameter
Settings.
8
Assistant Sensor Settings, Speed Sensor Settings, Throttle Function
Settings, System Settings and Power-on Password Settings. Please
refer to the Attached list 2.
To access Personalized Parameter Settings items option page, hold
both the UP and DOWN button for 2s, then hold both the UP and DOWN
button again.
To access the corresponding settings page, press the UP/DOWN
button to increase or decrease until the desired item is displayed, and
press the MODE button again.
1-5 flash
PAS Mode Option Interface
10
◆Controller Over-Current Cut Settings
CUR represents controller over-current cut settings. CUR value can
be changed from 7.0A to 22.0A. The default value is 15A.
To change basic settings, press the UP/DOWN button to increase
or decrease the value of the current.
Hold the MODE button for 2s and then return to previous menu.
11
To change the sensitivity of PAS settings, press the UP/DOWN button
to select sensitivity value.
Briefly press the MODE button and then access magnet disk
settings mode.
12
Speed Sensor Selection
◆Throttle Definition
Throttle Push-assistance Enable/Disable
HL represents throttle push-assistance function. HL-N represents
throttle assistance push function is disabled. HL-y represents throttle
assistance push function is enabled. The default value is N.
To change throttle push-assistance function, press the UP/DOWN
button to select Y or N.
Briefly press the MODE button.
Otherwise, to select N and then access Throttle Level Enable
Settings.
13
Throttle Level Enable or Disable Interface
◆System Settings
Delay time settings of battery power
DLY represents delay time of battery power settings. The default
value is 3s.
To change delay time settings, press the UP/DOWN button to select
delay time 3s, 6s, 12s.
Briefly press the MODE button to confirm and then access the max
speed limited.
14
Interface of Max Speed Limited Settings
■This setting is the priority version. The speed is the maximum set
by manufacturer.
Interface of Push-assistance
15
Interface of PAS Speed Settings
16
Power-on Password Entering Interface
17
Power-on Password Modifying Interface
◆Exit settings
In the settings state, briefly press the MODE button is to confirm the
input. Holding the MODE button is to store the settings, and then exit the
current settings. Holding the DOWN button is to cancel the operating but
not storing settings data, and then return to previous menu.
■If there is not any operations in one minute, the display will exit
the settings state.
Operation Cautions
Be careful of safe use. Don’t attempt to release the connector when
battery is on power.
◆ Try to avoid hitting.
18
◆ Make the display repaired when error code appears.
Connection layout
19
Line sequence table
■Some cable use the water-proof connector, users can not see the
inside color.
20
Attached list 2: Personality Parameter settings
Screen
No. Settings item
display
1 Battery Power Bar Settings
2 Power assistant level Settings
3 Over-current Cut Settings
4 Power Assistant Sensor Settings
5 Speed Sensor Settings
6 Throttle Function Settings
7 System Settings
8 Power-on Password Settings
21
Attached list 4:symbol definition
22