Arkote 31 Epoxy Primer (30608P3250)

AFNOR (NF T 36-005) Classification Famille 1 - Classe 6b 18/03/2011
ARKOTE 31 PRIMAIRE HOMOLOGUÉ SNCF SELON NF.F.19-290
Product Description
Type
Two components Epoxy Primer
Use
Anticorrosion Primer for metallic parts for rolling stocks and general industry.
Protection against stress corrosion.
SNCF Homologation for systems NFF 19220 / NFF 19290 / NFF 19223 / STMR 106 (RP 3120121 / RP 4021021)
Performance
Excellent adhesion
Very high resistance to corrosion
Very high resistance to agressive agents
Compatible with epoxy or polyurethan topcoat
Substrates and surface preparation
Advice Arkote 31 Primaire can be applied over sand blasted stell, eventually covered by a shop
primer (Artewash 12, Hydrowash, Aquaweld 12) (*), or over solvent cleaned smooth
steel (except stainless) or sand blasted aluminium.
In case of refinishing, Arkote 31 Primaire can be applied over old system sanded in
advanced, including bare parts.
(*) Sand blasting can be substituted by other mechanical pretreatments after a

qualification process.
Substrate Preparation
Ferrous metals Abrasive blasting
Non-ferrous metals Alumina blasting
Polyester Abrasion
Storage conditions
Advice 18 months in perfectly closed cans or drums, if not been opened, at a temperature
between -5°C and +35°C.
Health and Safety
For further information, refer to the MSDS which may be consulted on our web site www.mader-group.com
(customer code on products-safety.soficor@mader-group.com)
Two-component
Name Pot-Life (hh:mm)

DURCISSEUR P.ARKOTE 31 08:00
Print date 18/03/2011 Validation date 18/03/2011

The information below is based on our experience and does not imply any guarantee. Page 1 sur 3
SOFICOR-MÄDER Division SORITEC - Zone Industrielle d'Arrouet BP 55 - 49170 SAINT GEORGES SUR LOIRE - FRANCE
Tél : 02 41 36 51 51 - Fax : 02 41 39 10 24
Preparation and application
During the application, the following requirements must be observed:
15 °C < T° < 35 °C Hy < 70 %
1 - AIRLESS SPRAY Viscosity 40 s +/- 5 CA4 Volume Weight Tol +/- %

Base ARKOTE 31 PRIMAIRE HOMOLOGUÉ SNCF SELON NF.F.19-290 3 100
Hardener DURCISSEUR P.ARKOTE 31 1 23
Thinner
2 - PNEUMATIC SPRAYING Viscosity 40 s +/- 5 CA4 Volume Weight Tol +/- %

Thinner
3 - BRUSH / ROLLER Volume Weight Tol +/- %

Thinner
Table : Thinner ratio according to application method.
Advice PREPARATION :
- Mix the base during 3 min in order to uniformly disperse the product before adding
the hardener.
- Add hardener and thinner in order to get the right spray application viscosity.
- Given spray viscosity is only indicative. Please follow the given
base/hardener/thinner ratio.
- After mixing leave 15 minutes induction time prior application.
APPLICATION PROCESS RECOMMENDATION :

- AIRLESS application: 180 bar pressure, nozzle 0,28 to 0,33 mm (X11 to X13
GRACO or 06-XXX to 09-XXX KREMLIN).
- Pneumatic application: max 4,0 Bar Pressure, nozzle 1,2 to 1,4 mm.
- Application in 1 to 2 layers of 100-120 µm humid thickness.
FORCED CURING :
Please contact our technical assistance to have an adapted solution to your spray
booth.
CLEANING :
We recommend to clean the equipment directly after use with :
- Cleaning solvents : thinner T2745 or T2506.
Air drying
Characteristic Value
Dust dry 01:30 hours
Touch dry 05:00 hours
Hard dry
Overcoating 10:00 hours

Tél : 02 41 36 51 51 - Fax : 02 41 39 10 24

Technical data as supplied Technical data - Product ready for use
Characteristic Value Characteristic Value
Weight solids 60 % +/- 2 Weight solids 52 % +/- 2
Volume solids 40 % +/- 2 Volume solids 40 % +/- 2
Density 1,32 +/- 0,03 Recommended wet film thickness 120 µ +/- 10
Viscosity 80 ku +/- 10 KREBS at 20°C Recommended dry film thickness 50 µ +/- 5
Flash point 23 °C Theoretical coverage 8 m² / L. for 50 µ
Resistivity / Dry coating volumic ratio 44 % +/- 2
Fineness 8 Data for mixture n°1
PH
Advice
Shade Green
Sagging limit : 160 µm.
Appearance Satin-matt
Salt spray resistance at 50 µm thickness : 500 hours.
Gloss 25 µm thickness are obtained in one layer.
Delivery viscosity : 85 +/- 10 sec ISO 4

Spray viscosity : 60 +/- 5 sec ISO 4
Further information:
Important:
If a drying time of 48 hours is exceeded or a force curing is used, sanding is required in order to have a good recoatability.
Advice Note all drying and recoatable time have been measured in our laboratory under controled
humidity and temperature. Those values are given as indication and can vary with a different
application and drying conditions.

Tél : 02 41 36 51 51 - Fax : 02 41 39 10 24

Arkote 31 Epoxy Primer (30608P3250)

Uploaded by

Copyright:

Available Formats

Arkote 31 Epoxy Primer (30608P3250)

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Arkote 31 Epoxy Primer (30608P3250)

Uploaded by

Copyright:

Available Formats

AFNOR (NF T 36-005) Classification Famille 1 - Classe 6b 18/03/2011

ARKOTE 31 PRIMAIRE HOMOLOGUÉ SNCF SELON NF.F.19-290

Substrates and surface preparation

(*) Sand blasting can be substituted by other mechanical pretreatments after a

Health and Safety

Name Pot-Life (hh:mm)

Print date 18/03/2011 Validation date 18/03/2011

ARKOTE 31 PRIMAIRE HOMOLOGUÉ SNCF SELON NF.F.19-290

Preparation and application

During the application, the following requirements must be observed:

15 °C < T° < 35 °C Hy < 70 %

1 - AIRLESS SPRAY Viscosity 40 s +/- 5 CA4 Volume Weight Tol +/- %

2 - PNEUMATIC SPRAYING Viscosity 40 s +/- 5 CA4 Volume Weight Tol +/- %

3 - BRUSH / ROLLER Volume Weight Tol +/- %

Table : Thinner ratio according to application method.

APPLICATION PROCESS RECOMMENDATION :

Print date 18/03/2011 Validation date 18/03/2011

ARKOTE 31 PRIMAIRE HOMOLOGUÉ SNCF SELON NF.F.19-290

Delivery viscosity : 85 +/- 10 sec ISO 4

Print date 18/03/2011 Validation date 18/03/2011

You might also like