Digital Trainer PAD234 Operators Manual
Digital Trainer PAD234 Operators Manual
OPERATORS MANUAL
Rev. 7/94
******* WARNING ******* Do not use all sources simultaneously !! keep liquids away from the PAD unit !! Do not use near flammable materials !!!
circuit protection.
(+) 5
(+) and () 15 volt variable supply (from 1.5 V to 15V) with 1.5 amp short circuit protection.
(+)12.6 Volt AC center tap power supply. FUNCTION GENERATOR Sine, square, and triangle output wave shape. 1 Hz to 100 Khz in 5 ranges, uncalibrated, buffered, adjustable output 0 to 15 volts peak to peak. Frequency determined by COARSE FREQUENCY
FINE FREQUENCY adjustment knob. Rise and fall time is 400 ns.
INDICATORS SWITCHES
8 BUFFERED TTL compatible LED'S. 8 binary toggle switches (0 or 5 Volts) 2 momentary pulse switches, debounced with complimentary outputs 2 breadboards with 840 plug-in tie points each. 117 Volts at .5 Amps High impact plastic case with a 3-wire grounded
line cord. Fuse protected AC line.
OPERATION
DC POWER SUPPLY Use of 5V Supply Use of + 12V Use of 12V VARIABLE DC SUPPLY +5, +12, 12, located in the vertical row of binding posts, positioned along the left side of the breadboards.
(ground).
Connect the load between the binding post and the GND Connector the load between the Binding Post marked + 12V and the Binding Post marked GND (ground). Connect the load between the Binding Post marked 12V and the Binding Post marked GND (ground) . Located above left to the main breadboards and identified as + 15V, controlled by the appropriate knobs. (Lower left hand corner of the top plate.) Connect the load between the tie blocks identified as + 15
V and OV (ground). Use the knob marked + 15V to control the output voltage of this tie block.
Connect the load between the tie block identified as 15V and OV (ground). Use the knob marked 15V to control the output voltage of this tie block. Located above right to the main breadboards and identified as AC Volts.
AC POWER SUPPLY Using the 6.3 VAC Using the 12.6 VAC FUNCTION GENERATOR
Connect the load between the tie blocks marked 6.3 and 6.3. The output for the GENERATOR and CLOCK are Iocated in
the top two Binding posts in the vertical row, on the left hand side of the breadboards marked GEN and CLOCK.
The generator and clock outputs are controlled by the five knobs located on the far left hand side of the PAD unit and marked accordingly.
GENERATOR (CONTINUED) Before using the Generator or Clock output in an actual circuit, familiarize yourself with the functions of the five control knobs and the effects they have on the output waveforms. Connect an oscilloscope to the GEN Binding post and GND Binding post as described above. Adjust the O-scope as necessary to observe a clearly visible waveform. By using the five control knobs observe how you are able to adjust the output waveforms, by using these controls. (See the section below labeled "Using the Generator".
Connect the load between the Binding posts . marked CLOCK and GND (ground). Select the appropriate frequency using the knob
marked COARSE FREQUENCY.
Connect the load between the Binding Posts marked GEN (Function Generator) and GND (ground) .
1. Select the type of waveform required by using the top left knob. 2. Set the COARSE FREQUENCY knob to the correct range. 3. Fine tune the frequency (using the knob marked FINE FREQUENCY) to the exact frequency required. 4. Adjust the amplitude (using the AMPLITUDES) knob to adjust the output voltage maintaining a clear waveform. 5. Adjust the offset as needed with the bottom control knob marked OFFSET.
DIGITAL SECTION
Located across the top of the PAD This section includes eight manual toggle switches, eight LED tie blocks and two pulse switches.
Connect the device between the tie block to be used (numbered 0 to 7) and GND (ground) . When the toggle switch is in the up position, +5 volts is supplied to the device. When the switch is in the down position 0 volts is applied.
Connect the device to the tie block directly under the LED to be used. When + 5V is applied the LED will light, when 0 is applied it will be off. For + 5V pulse connect the device to the tie block marked O. When the switch is pulsed the output at the tie block will be +5V. For O V pulse, connect the device to the tie block marked 1. +5 V will be applied to the point block till the switch is pulsed, then the output will be O V.
To become more familiar with the toggle switches and LED tie points, take a piece of wire and connect between one of the Toggle tie point blocks and one of the LED tie point blocks. Flip the switch and observe that voltage is being applied, lighting the LED. Repeat this procedure using the momentary pulse switches.
A 16-pin Insulation Displacement Connector (IDC), labeled EXTENDER on the top plate of the PAD 234, allows ribbon-cable connection to personal computers and other electronic equipment. The user can supply power, analog, and digital signals to add-on boards via a ribbon cable. The EXTENDER has eight uncommitted bidirectional lines which can be easily connected via tieblocks to the LEDs and switches of the PAD 234. Also, add-ons or external equipment can be interfaced to circuits already breadboarded on the trainer. In addition, the function generator built into the PAD 234 can be either AM or FM modulated by applying signals to either pins 15 and 16 of the IDC or tie-blocks X and Y. Since pin 15 (FM) is capacitively coupled to the function generator, it may be used as an additional DC-level signal in certain applications.