Codigo de Falla - Toyota Serie 8
Codigo de Falla - Toyota Serie 8
Codigo de Falla - Toyota Serie 8
19-6
Wrench Detection Described
Indication Spanner Error mode Phenomenon on vehicle
lamp ECU on page
01-1 01-1 Blinking 4Y-ECS Fuel feedback control error (gasoline) rich
19-14
01-2 01-2 Blinking 4Y-ECS Fuel feedback control error (gasoline) lean
The engine speed is unstable and it may stop.
01-3 01-3 Blinking 4Y-ECS Fuel feedback control error (LPG/CNG) rich
19-18
01-4 01-4 Blinking 4Y-ECS Fuel feedback control error (LPG/CNG) lean
01-5 01-5 Blinking 4Y-ECS O2 sensor open abnormality The engine speed is unstable and it may stop. 19-23
01-6 01-6 Blinking 4Y-ECS O2 sensor heater open abnormality Display only 19-25
02-1 02-1 Blinking 4Y-ECS Intake temperature sensor open abnormality The engine may have a problem at low
19-27
02-2 02-2 Blinking 4Y-ECS Intake temperature sensor short abnormality temperatures.
03-1 03-1 Blinking 4Y-ECS Intake pipe pressure sensor open abnormality
18-3 18-3 Blinking 4Y-ECS Crank angle sensor open abnormality Display only 19-63
Continuation of engine idling status
Maximum speed may be limited
1F-1 ~ 8 1F-1 ~ 8 Blinking ASC CPU error 19-67
Function of automatic idle speed increse during
lifting limited
41-1 41-1 Blinking SAS/OPS Matching connector open abnormality Display only 19-68
51-1 51-1 Blinking SAS/OPS Speed sensor open abnormality The vehicle speed indicator shows 0 km/h
Partial limitation of the rear wheel swing control
function. 19-69
51-2 51-2 Blinking SAS/OPS Speed sensor GND short abnormality Knob offest compensation stops
Partial limitation of the drive control function.
52-1 52-1 Blinking SAS/OPS Yaw rate sensor open abnormality
Partial limitation of the rear wheel swing control
52-2 52-2 Blinking SAS/OPS Yaw rate sensor VCC short abnormality 19-71
function
52-3 52-3 Blinking SAS/OPS Yaw rate sensor neutral voltage error
Partial limitation of the rear wheel swing control
54-1 54-1 Blinking SAS/OPS Swing lock solenoid open circuit or load short abnormality 19-73
function
61-1 61-1 Blinking SAS/OPS Load sensor open abnormality Partial limitation of the rear wheel swing control
function
Partial limitation of mast control function 19-75
61-2 61-2 Blinking SAS/OPS Load sensor VCC short abnormality Limitation of the drive control function
19-7
Load indicator cannot display
19-8
Wrench Detection Described
Indication Spanner Error mode Phenomenon on vehicle
lamp ECU on page
62-1 62-1 Blinking SAS/OPS Tilt angle sensor open abnormality
Partial limitation of mast control function 19-78
62-2 62-2 Blinking SAS/OPS Tilt angle sensor VCC short abnormality
63-1 63-1 Blinking SAS/OPS Tilt switches simultaneously ON
63-2 63-2 Blinking SAS/OPS Tilt switch forward tilt SW short Partial limitation of mast control function 19-81
63-3 63-3 Blinking SAS/OPS Tilt switch backward tilt SW short
64-1 64-1 Blinking SAS/OPS Lift lower lock solenoid open circuit or load short abnormality Lift lower may stop 19-84
Forward tilt may stop, backward tilt may go fully
65-1 65-1 Blinking SAS/OPS Tilt control solenoid open circuit or load short abnormality 19-86
back
66-1 66-1 Blinking SAS/OPS Outside matching value range for tilt angle error Partial limitation of mast control function 19-88
Partial limitation of the rear wheel swing control
function
lifting limited
19-92
Function of automatic idle speed increse during
68-2 68-2 Blinking SAS/OPS Lift switch raise SW short abnormality
lifting limited
68-3 68-3 Blinking SAS/OPS Lift switch lower SW short abnormality Lowering may stop
Backward tilt lock solenoid open circuit or load short
69-1 69-1 Blinking SAS/OPS Backward tilt may stop 19-95
abnormality
71-1 71-1 Blinking SAS/OPS Tire angle sensor open abnormality
Knob offest compensation stops 19-97
71-2 71-2 Blinking SAS/OPS Tire angle sensor VCC short abnormality
72-1 72-1 Blinking SAS/OPS Steering-wheel angle sensor SS1 open abnormality
72-2 72-2 Blinking SAS/OPS Steering-wheel angle sensor SS2 open abnormality
Knob offest compensation stops 19-100
72-3 72-3 Blinking SAS/OPS Steering-wheel angle sensor SSC open abnormality
72-4 72-4 Blinking SAS/OPS Steering-wheel angle sensors SS1 and SS2 open abnormality
Wrench Detection Described
Indication Spanner Error mode Phenomenon on vehicle
lamp ECU on page
Knob position compensation solenoid open circuit or load short
73-1 73-1 Blinking SAS/OPS Knob offest compensation stops 19-108
abnormality
74-1 74-1 Blinking SAS/OPS Outside matching value range for tire angle error Knob offest compensation stops 19-110
Traveling and material handling possible even
after leaving the seat.
A5-1 A5-1 Blinking SAS/OPS Seat switch GND short abnormality 19-111
Parking brake reminder and release reminder
alarm partially disabled.
A7-1 A7-1 Blinking SAS/OPS Brake switch GND short abnormality Partial limitation of the drive control function 19-113
AD-1 AD-1 Blinking SAS/OPS CAN communication 4Y-ECS or ASC data reception error Partial limitation of the drive control function
AD-2 AD-2 Blinking 4Y-ECS CAN communication SAS/OPS data reception error Partial limitation of the drive control function
Limitation of the drive control function
Function of automatic idle speed increse during 19-115
19-9
19-10
Wrench Detection Described
Indication Spanner Error mode Phenomenon on vehicle
lamp ECU on page
Travelling and material handling enabled even
EC-1 EC-1 Blinking SAS/OPS Unload solenoid open circuit or load short abnormality 19-131
after leaving the seat.
F1-1 – Blinking
Meter SAS/OPS data reception error Display only 19-133
F2-1 – Blinking
F4-1 ~ 8 F4-1 ~ 8 Blinking Display CPU error Display not stable 19-134
H1-1 H1-1 Blinking SAS/OPS Lift lever potentiometer open abnormality
H1-2 H1-2 Blinking SAS/OPS Lift lever potentiometer VCC short abnormality Lift stop
H1-3 H1-3 Blinking SAS/OPS Lift lever potentiometer assembly error 19-135
H1-4 H1-4 Blinking SAS/OPS Lift lever potentiometer neutral abnormality Material handling disabled
H1-5 H1-5 Blinking SAS/OPS Lift lever potentiometer matching value abnormality Lift stop
H2-1 H2-1 Blinking SAS/OPS Tilt lever potentiometer open abnormality
H2-5 H2-5 Blinking SAS/OPS Tilt lever potentiometer matching error Tilt stop
H3-1 H3-1 Blinking SAS/OPS Attachment 1 lever potentiometer open abnormality
H3-2 H3-2 Blinking SAS/OPS Attachment 1 lever potentiometer VCC short abnormality Attachment 1 stop
H3-3 H3-3 Blinking SAS/OPS Attachment 1 lever potentiometer combination error 19-141
H3-4 H3-4 Blinking SAS/OPS Attachment 1 lever potentiometer neutral abnormality Material handling disabled
H3-5 H3-5 Blinking SAS/OPS Attachment 1 lever potentiometer matching value abnormality Attachment 1 stop
H4-1 H4-1 Blinking SAS/OPS Attachment 2 lever potentiometer open abnormality
H4-2 H4-2 Blinking SAS/OPS Attachment 2 lever potentiometer VCC short abnormality Lever 2 stop
H4-3 H4-3 Blinking SAS/OPS Attachment 2 lever potentiometer combination error 19-144
H4-4 H4-4 Blinking SAS/OPS Attachment 2 lever potentiometer neutral abnormality Material handling disabled
H4-5 H4-5 Blinking SAS/OPS Attachment 2 lever potentiometer matching value abnormality Lever 2 stop
H5-1 H5-1 Blinking SAS/OPS Lift PUSH solenoid open abnormality
Lift may stop 19-147
H5-2 H5-2 Blinking SAS/OPS Lift PULL solenoid open abnormality
H6-1 H6-1 Blinking SAS/OPS Tilt PUSH solenoid open abnormality
Tilt may stop 19-149
H6-2 H6-2 Blinking SAS/OPS Tilt PULL solenoid open abnormality
H7-1 H7-1 Blinking SAS/OPS Attachment 1 PUSH solenoid open abnormality
Attachment 1 may stop 19-151
H7-2 H7-2 Blinking SAS/OPS Attachment 1 PULL solenoid open abnormality
Wrench Detection Described
Indication Spanner Error mode Phenomenon on vehicle
lamp ECU on page
H8-1 H8-1 Blinking SAS/OPS Attachment 2 PUSH solenoid open abnormality
Attachment 2 may stop 19-153
H8-2 H8-2 Blinking SAS/OPS Attachment 2 PULL solenoid open abnormality
HA-1 HA-1 Blinking SAS/OPS 3/4 way change relay GND short abnormality Attachment switching disabled 19-155
19-11
WARNING LIST
19-12
Caution:
If the wrench lamp illuminates and the following phenomena occur on the vehicle without an error being displayed, it is not a fault. Take the
appropriate corrective action.
Wrench Detection
Indication Memory Phenomenon on vehicle Content of warning Appropriate corrective action
lamp ECU
Water
temperatur Top speed and load lifting speed are limited.
OB-1 – 4Y-ECS Overheat Leave the vehicle at idle for a while
e gauge (Only when OPT equipped)
flashing
Swing lock control is always locked
Knob offset occurrence Use a battery of the specified
– – On SAS/OPS High battery voltage
Material handling disabled (mini lever) voltage
Material handling except lifting disabled