Rayson

Bluetooth ® Module
Class1 BC04-ext Module BTM-222
Features Outline

■ Bluetooth Ver. 2.0+EDR certification

■ Transmit Power up to +18dBm(class1)
■ Low current consumption:
Hold, Sniff, Park, Deep sleep mode
■ 3.0V to 3.6V operation
■ Full Bluetooth Data rate over UART and USB
■ Support up to 7 ACL links and 3 SCO links
■ Enhanced Data Rate(EDR) compliant
for both 2Mbps and 3Mbps modulation modes
■ Interface: USB, UART&PCM( for voice codec)
■ SPP firmware with AT commands
■ RoHS Compliant
■ Mini outline: 28.2 X 15.0 X 2.8 mm

Application
● Access point
● Domestics and Industrial applications
● Serial Adapter
● GPS, POS, Barcode Reader

Block Diagram
 Electrical Characteristics
Absolute Maximum Ratings
Parameter Min. Max. Unit
Storage Temperature -40 +85 ℃
Supply Voltage(VDD) 2.7 3.6 DCV
Supply Voltage(PVCC) 3.0 3.3 DCV
Other Pin Voltage Vss-0.4 VDD+0.4 DCV
Recommended Operating Conditions
Parameter Min. Max. Unit
Temperature -10 +70 ℃
Supply Voltage for UART 3.0 3.6 DCV
Supply Voltage for USB 3.0 3.6 DCV
General Electrical Specification

Parameter Description Min. Typ. Max. Unit

Carrier Frequency 2.402 2.480 GHz
RF Output Power Measured in 50ohm 15 16.5 18 dBm
RX sensitivity - -88 -86 dBm
Load Impedance No abnormal Oscillation 5:1
Input Low Voltage RESET,UART,GPIO,PCM -0.30 - 0.80 DCV
Input High Voltage RESET,UART,GPIO,PCM 0.7VDD - VDD+0.3 DCV
Output Low Voltage UART,GPIO,PCM - - 0.40 DCV
Output High Voltage UART,GPIO,PCM VDD-0.4 - - DCV
Average Current Consumption Receive DM1 114 mA

Radio Characteristics - Basic Data Rate

Transmitter , VDD = 3.3V Temperature =+20°C

Frequency Min. Typ. Max. Bluetooth Unit
(GHz) Specification
2.402 15 16.5 18 dBm
RF transmit power 2.441 15 16.5 18 -6 to +20 dBm
2.480 15 16.5 18 dBm
Initial carrier frequency tolerance 2.402 - 12 25 kHz
2.441 - 10 25 ±75 kHz
2.480 - 9 25 kHz
-20dB bandwidth for modulated 2.402 - 890 1000 kHz
carrier 2.441 - 870 1000 < 1000 kHz
2.480 - 820 1000 kHz
Carrier Frequency Drift (single 2.402 - ±10 ±20 kHz
slot packet DH1) 2.441 - ±10 ±20 <25 kHz
2.480 - ±10 ±20 kHz
Carrier Frequency Drift (five slot 2.402 - ±10 ±20 kHz
packet DH5) 2.441 - ±10 ±20 <40 kHz
2.480 - ±10 ±20 kHz
2.402 - ±7 ±14 kHz/50µs
Drift Rate 2.441 - ±7 ±14 <20 kHz/50µs
2.480 - ±7 ±14 kHz/50µs
RF power control range 16 25 - >16 dB
 2.402 145 165 170 kHz
avg avg
△f1 “Maximum Modulation” 2.441 145 165 170 140<△f1 <175 kHz
2.480 145 165 170 kHz
2.402 115 150 - kHz
maz
△f2 “Minimum Modulation” 2.441 115 150 - >115 kHz
2.480 115 150 - kHz
Adjacent channel transmit power F=F0±2MHz - -35 -20 < - 20 dBm
Adjacent channel transmit power F=F0±3MHz - -45 -40 < - 40 dBm
Adjacent channel transmit power F>F0 +3MHz - -50 -40 < - 40 dBm
Adjacent channel transmit power F<F0 -3MHz - -50 -40 < - 40 dBm

Receiver , VDD = 3.3V Temperature =+20°C

Frequency Min. Typ. Max. Bluetooth Unit
(GHz) Specification
Sensitivity at 0.1% BER 2.402 - -88 -86 dBm
2.441 - -88 -86 < - 70 dBm
(Single slot packets) 2.480 - -88 -86 dBm
Sensitivity at 0.1% BER 2.402 - -88 -86 dBm
2.441 - -88 -86 < - 70 dBm
(Multi slot packets) 2.480 - -88 -86 dBm
Maximum received signal level at 2.402 -20 -10 - dBm
0.1% BER 2.441 -20 -10 - > - 20 dBm
2.480 -20 -10 - dBm
C/I co-channel - 6 11 < 11 dB
Adjacent channel selectivity C/I F=F0 +1 MHz - -4 - <0 dB
Adjacent channel selectivity C/I F=F0 - 1MHz - -4 - <0 dB
Adjacent channel selectivity C/I F=F0 +2 MHz - -38 - < - 30 dB
Adjacent channel selectivity C/I F=F0 - 2MHz - -23 - < - 20 dB
Adjacent channel selectivity C/I F>=F0 +3 MHz - -45 - < - 40 dB
Adjacent channel selectivity C/I F<=F0 -5 MHz - -44 - < - 40 dB
Adjacent channel selectivity C/I F=Fimage - -22 - <-9 dB
F0 = 2441 MHz
Maximum level of intermodulation interference -30 > -39 dBm
(n=5)

Radio Characteristics – Enhanced Data Rate

Transmitter , VDD = 3.3V Temperature =+20°C
Frequency Min. Typ. Max. Bluetooth Unit
(GHz) Specification
2.402 - 6 - dBm
(note)
Maximum RF transmit power 2.441 - 6 - -6 to +20 dBm
2.480 - 7 - dBm
Relative transmit power - -1.6 - -4 to +1 dB
π/4 DQPSK - 2 - < ±10 for all blocks kHz
Maximum carrier frequency stability w0
π/4 DQPSK - 6 - < ±75 for all packets kHz
Maximum carrier frequency stability wi
π/4 DQPSK - 8 - < ±75 for all blocks kHz
Maximum carrier frequency stability | w0 + wi |
8 DPSK - 2 - < ±10 for all blocks kHz
Maximum carrier frequency stability w0
8 DPSK - 6 - < ±75 for all packets kHz
Maximum carrier frequency stability wi
8 DPSK - 8 - < ±75 for all blocks kHz
Maximum carrier frequency stability | w0 + wi |
π/4 DQPSK RMS DVEM - 7 - < 20 %
Modulation Accuracy 99% DEVM - 13 - < 30 %
Peak DEVM - 19 - < 35 %
8 DPSK RMS DVEM - 7 - < 13 %
Modulation Accuracy 99% DEVM - 13 - < 20 %
Peak DEVM - 17 - < 25 %
F>F0 +3 MHz - <-50 - < -40 dBm
F<F0 -3 MHz - <-50 - < -40 dBm
F=F0 -3 MHz - -46 - < -40 dBm
F=F0 -2 MHz - -34 - < -20 dBm
In-band spurious emissions
F=F0 -1 MHz - -35 - < -26 dBm
F=F0 +1 MHz - -35 - < -26 dBm
F=F0 +2 MHz - -31 - < -20 dBm
F=F0 +3 MHz - -33 - < -40 dBm
EDR Differential Phase Encoding No > 99 %
Errors

Receiver , VDD = 3.3V Temperature =+20°C

Modulation Min. Typ. Max. Bluetooth Unit
Specification
Sensitivity at 0.1% BER π/4 DQPSK - -87 - < -70 dBm
8 DPSK - -78 - < -70 dBm
Maximum received signal level at π/4 DQPSK - -8 - > -20 dBm
0.1% BER 8 DPSK - -10 - > -20 dBm
C/I co-channel at 0.1% BER π/4 DQPSK - 10 - < +13 dB
8 DPSK - 19 - < +21 dB
Adjacent channel selectivity C/I π/4 DQPSK - -10 - <0 dB
F=F0 +1 MHz 8 DPSK - -5 - < +5 dB
Adjacent channel selectivity C/I π/4 DQPSK - -11 - <0 dB
F=F0 -1 MHz 8 DPSK - -5 - < +5 dB
Adjacent channel selectivity C/I π/4 DQPSK - -40 - < -30 dB
F=F0 +2 MHz 8 DPSK - -40 - < -25 dB
Adjacent channel selectivity C/I π/4 DQPSK - -23 - < -20 dB
F=F0 -2 MHz 8 DPSK - -20 - < -13 dB
Adjacent channel selectivity C/I π/4 DQPSK - -45 - < -40 dB
F=F0 +3 MHz 8 DPSK - -45 - < -33 dB
Adjacent channel selectivity C/I π/4 DQPSK - -45 - < -40 dB
F=F0 -5 MHz 8 DPSK - -45 - < -33 dB
F0 = 2405, 2441, 2477 MHz
Adjacent channel selectivity C/I π/4 DQPSK -20 < -7 dB
F=Fimage 8 DPSK -15 <0 dB

Note :
Measurement made using a POWER_TABLE entery of TX_PRE 80, INT PA63, EXT PA255. This ensures that the
Bluetooth requirements for ACP and those defined by the FCC and ETSI are satisfied over the operating
temperature rang of -5℃to +45℃. Although the design is capable of generating in excess of +18dBm, regulatory
compliance over the full temperature range of -5℃ to +45℃ will not be satisfied if the transmit power
approaches this value.
 BTM-222 Pin Function

Pin No. Pin Name Pin Type Description

1 GND GND Common ground
2 PVCC Power Power Amp. Power Supply(3.3V)
3 AIO(0) Bi-directional Programmable I/O terminal , 32KHz sleep clock input
4 AIO(1) Bi-directional Programmable I/O terminal
5 PIO(0) Bi-directional Programmable I/O terminal, RX Enable
6 PIO(1) Bi-directional Programmable I/O terminal, TX Enable
7 PIO(2) Bi-directional Programmable I/O terminal, USB_PULL_UP, CLK_REQ_OUT
8 PIO(3) Bi-directional Programmable I/O terminal, USB_WAKE_UP, CLK_REQ_IN
9 PIO(4) Bi-directional Programmable I/O terminal, USB_ON, BT_Priority/Ch_Clk output for
co-existence signalling
10 GND GND Common ground
11 PIO(5) Bi-directional Programmable I/O terminal, USB_DETACH, BT_Active output for
co-existence signalling
12 PIO(6) Bi-directional Programmable I/O terminal, CLK_REQ, WLAN_Active/Ch_Data input
for for co-existence signalling
13 PIO(7) Bi-directional Programmable I/O terminal
14 PIO(8) Bi-directional Programmable I/O terminal
15 PIO(9) Bi-directional Programmable I/O terminal
16 RESET CMOS input Reset input of module, Active low reset
17 VCC Power Module power supply input
18 GND GND Common ground
19 GND GND Common ground
20 USB_DP Bi-directional USB data plus
21 USB_DN Bi-directional USB data minus
22 PCM_SYNC Bi-directional Synchronous data sync
23 PCM_IN CMOS input Synchronous data input
24 PCM_OUT CMOS output Synchronous data output
25 PCM_CLK Bi-directional Synchronous data clock
26 UART_RX CMOS input UART data input
27 UART_TX CMOS output UART data output
28 UART_RTS CMOS output UART request to send(active low)
29 GND GND Common ground
30 UART_CTS CMOS input UART clear to send(active low)
31 SPI_MOSI CMOS input Serial Peripheral Interface data input
32 SPI_CSB CMOS input Chip select for Synchronous Serial Interface(active low)
33 SPI_CLK CMOS input Serial Peripheral Interface clock
34 SPI_MISO CMOS output Serial Peripheral Interface data output
35 PIO(11) Bi-directional Programmable I/O terminal
36 PIO(10) Bi-directional Programmable I/O terminal
37 RF_IO Analogue Antenna interface
38 GND GND Common ground
SPP AT Command sets
When it＇s in master mode. This command establish a connection. When it＇s in slave
A mode, the command will be rejected.
Modifiers Description
(Establish a
A Connect to a Bluetooth device (It＇s only available when “ATD=
connection)
xxxxxxxxxxxx＂ assigned)
A1~A8
Connect to a Bluetooth neighborhood device 1~8 (ATF? Result)

B This command display the local device BD address

Modifiers Description
(Display local
BD address) B? Inquire the Local BD address
For security purpose, We can specifies the unique remote device can be connected. In
D master role, it automatically inquire and search the slave even the slave is undiscoverable.
In slave role, the command should be as a filter condition to accept the master＇s inquiry.
(Set Remote BD Modifiers Description
address)
D=xxxxxxx
"xxxx-xx-xxxxxx" is 12 digit hex symbol
xxxxx
D0 Clear Remote BD address setting, inquire any slave in master mode or accept
(Default) any master in slave mode.
D?
Inquire the Remote BD address setting

This command specifies whether the device should echo characters received from the
E UART back to the DTE/DCE.
Modifiers Description
(Local Echo)
E0 Command characters received from the UART are not echoed back to the
DTE/DCE.
E1 Command characters received from the UART are echoed back to the
(Default) DTE/DCE.
E?
Inquire the current setting

This command is used to find any bluetooth device in neighborhood within 60 seconds
timeout. If any device is found, its name and address will be listed. The search ends with a
F message “Inquiry ends, xx device(s) found.＂
This command is available only when the adaptor is in the master role.
(Find Bluetooth
Modifiers Description
device)
F? Inquire scan Bluetooth neighborhood devices.
This command specifies whether the device could be discovered by remote master device.
H note : waitting for 15 seconds afert ATH1 command to take the effect

Modifiers Description
(Discoverable
H0 The device enters undiscoverable mode. If a pair have been made, the
Control)
original connection could be connected again. But other remote master device
can not discovery this device.
H1
The device enters discoverable mode.
(Default)
H? Inquire the current setting
This command is used to Inquiry the F/W version
I
(Information) Modifiers Description
I? Inquire the version Codes
This command is used to specify one or two stop bits of COM port
K Modifiers Description
K0
(Stop bits One Stop bit
(Default)
setting)
K1 Two stop bits
K? Inquire the current setting
This command is used to specify the baud rate of COM port
L Modifiers Description
L0 4800bps
(Baud Rate
Control) L1 9600bps
L2
19200bps
(Default)
L3 38400bps
L4 57600bps
L5 115200bps
L6 230.4Kbps

L7 460.8Kbps

L? Inquire the current setting

This command is used to specify the parity bit setting of COM port
M Modifiers Description
M0
(Parity bits None Parity bit.
(Default)
setting)
M1 Odd parity setting.
M2 Even parity setting
M? Inquire the current setting
We can specifies the device a friendly name using 0 to 9, A to Z, a to z, space and –,
which are all valid characters. Note that "firs space or -, last space or – isn＇t permitted".
N The default name is “Serial Adaptor＂

Modifiers Description
(Set device
name) N=xxxxx "xxxxx" is a character string, maxima length is 16

D? Inquire the device name

When it＇s in master mode .The command is used to enable/disable auto-connection
O feature. When it＇s in slave mode, the command will be rejected.
Modifiers Description
(Auto connect
O0 Automatically connectting to a device which is assigned in “ATD＂ or
setting)
(Default) any available device if “ATD＂ was not assigned.
O1 Disable auto-connection feature, user should manually use
“ATA＂command to connect a remote device.
O? Inquire the current setting
This command specifies the PIN number. It control to off the PIN code authorization that
P allow to establish a connection without PIN code.
Default PIN number is "1234"
(Set PIN code) Modifiers Description

P=xxxx "xxxx" is 4~8 digit string

 (Default)
P0
Turn off the PIN code authorization

P? Inquire the current PIN number

The command is used to determine if result Codes should be sent to the DTE/DCE. When
Q result Codes are supressed, the device does not generate any characters in response to the
completion of a command or when an event occurs.
(Result Four Result Codes : OK,CONNECT,DISCONNECT,ERROR
Code Modifiers Description
Supression)
Q0
The device will send Result Codes to the DTE/DCE.
(Default)
Q1 The device will not send Result Codes to the DTE/DCE.
Q? Inquire the current setting
This command specifies whether the device could be master or slave device. If change the
R role, the adaptor will warm start and clear all paired addresses.
Modifiers Description
(Set Role)
R0 The device as master role.
R1
The device as slave role.
(Default)
R? Inquire the current setting
This command will prompt “Enter DFU mode, Are you sure (y/n)?＂message, then press
U Y to confirm the command. Then you should connect USB cable to PC and run DFU
wizard. ( DFU wizard please contact us www.rayson.com)
(F/W upgrade)
Modifiers Description

U=pass
Pass word = RaysonUpgrade ,Go into Upgrade F/W Mode
word
Restore different application setting and warm start.
Z Modifiers Description
Z0 Restore factory default setting (19200bps, slave ….)
(Application
setting) Z? Inquire the current setting

The factory settings of UART are as follows:

z Baud rate: 19200 bps
z Data bit: 8
z Parity: none
z Stop bit: 1
z Flow control: H/W or none
z Others: Please refer to AT Command Sets.
BTM-22x Dimension
 Qualified Product Notice
BQB: Juei-Hsin Chin
Hyper Taiwan Technology, Inc.
7F-1, No. 92, Sec.1 Nei-Hu Rd., Taipei Taiwan, R.O.C. 114

QPN Number QPNHTTJ050 Assessment Date 11.10.2005

Listing Date 11.10.2005

Applicant Information
Applicant Rayson Technology Co., Ltd Contact Person Tim Lin
Address 1F, No. 9, R&D Rd. 2, Science-Based Phone Number +886.3.563.3666
Industrial Park, Hsin-Chu, 300 Taiwan, R.O.C Fax Number +886.3.563.3688

URL http://www.rayson.com Email Address sales@mail.rayson.com

Manufacturer Information

Product Information
Product Name Class 1 Module Product Category Components
Product ID BTM-22x, BTM-23x Product Type Comp-HW-Integrated
Hardware Version A1 Software Version N/A
Firmware Version cyt_8unified_fl_bt2.0_19p2
Supported Protocol
RF, BB, LM, HCI, HCI-USB, HCI-RS232, HCI-UART, L2CAP, SDP, RFCOMM

Supported Profile GAP, SPP

Reference Information
Product Reference Document V1.0
Bluetooth Specification V2.0 + EDR
Test Case Reference List TCRL_EDR_2005-1-BQRB1, TCRL_P1_1_2005-1-BQRB1

I certify that the Class 1Module has a Bluetooth Brand License based on the requirements as described in Section 6.2.1,
Pre-Tested Bluetooth Components, of the Bluetooth Program Reference Document 1.0

San Lorenzo, California / 11.10.2005