Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 84 views

    P 0340

    Uploaded by

    Carlos Medina Castillo

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    P 0340

    Uploaded by

    Carlos Medina Castillo
    84 views3 pages

    Original Title

    p0340

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    84 views3 pages

    P 0340

    Uploaded by

    Carlos Medina Castillo

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    2008 Chevrolet Aveo LT

    2008 ENGINE Engine Controls and Fuel - 1.6L - Aveo, Swift+ (Canadian) & Wave (Canadian)

    DTC P0016 OR P0340


    DIAGNOSTIC INSTRUCTIONS

    l Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    l Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    l Diagnostic Procedure Instructions provides an overview of each diagnostic category.

    DTC DESCRIPTORS

    DTC P0016

    Camshaft Position (CMP) Sensor Performance

    DTC P0340

    Camshaft Position (CMP) Sensor Circuit

    DIAGNOSTIC FAULT INFORMATION

    Short to Open/High Short to Signal


    Circuit Ground Resistance Voltage Performance
    Ignition 1 Voltage * P0340 - P0016
    CMP Sensor Signal P0016, P0340 P0340 P0340 P0016
    Low Reference - P0340 - P0016
    * Engine cranks but does not run and the fuse for the ignition circuit opens.

    CIRCUIT/SYSTEM DESCRIPTION

    The camshaft position (CMP) sensor correlates the crankshaft to camshaft position so that the engine control
    module (ECM) can determine which cylinder is ready to be fueled by an injector. As the camshaft rotates,
    the reluctor wheel interrupts a magnetic field produced by a magnet within the sensor and sends a signal to
    the ECM through the signal circuit. The CMP sensor circuits are directly connected to the ECM. The CMP
    sensor also determines which cylinder is misfiring. The CMP sensor circuits consist of the following:

    l An ignition 1 voltage
    l A low reference
    l A CMP signal

    CONDITIONS FOR RUNNING THE DTC

    l DTCs P0335 and P0336 are not set.


    l The engine is running.
    l The DTCs run continuously once the above conditions are met.

    CONDITIONS FOR SETTING THE DTC

    P0016

    martes, 11 de agosto de 2020 11:49:55


    11:49:38 a. m. Page 1 © 2011 Mitchell Repair Information Company, LLC.
    2008 Chevrolet Aveo LT
    2008 ENGINE Engine Controls and Fuel - 1.6L - Aveo, Swift+ (Canadian) & Wave (Canadian)

    The ECM detects an incorrect CMP signal for greater than 10 crankshaft revolutions.

    P0340

    The ECM detects no CMP signal for greater than 1 second.

    ACTION TAKEN WHEN THE DTC SETS

    DTCs P0016 and P0340 are Type A DTCs.

    CONDITIONS FOR CLEARING THE DTC

    DTCs P0016 and P0340 are Type A DTCs.

    DIAGNOSTIC AIDS

    The following conditions can also set the DTC:

    l Physical damage to the CMP sensor or the reluctor wheel


    l Excessive play or looseness of the CMP sensor or the reluctor wheel
    l Improper installation of the CMP sensor or the reluctor wheel
    l Foreign material passing between the CMP sensor and the reluctor wheel
    l Excessive air gap between the CMP sensor and the reluctor wheel

    REFERENCE INFORMATION

    Schematic Reference

    Engine Controls Schematics (MR140 w/o Throttle Actuator Control) or Engine Controls Schematics
    (MT34 w/Throttle Actuator Control) or Engine Controls Schematics (Hatchback)

    Electrical Information Reference

    l Circuit Testing
    l Connector Repairs
    l Testing for Intermittent Conditions and Poor Connections
    l Wiring Repairs

    DTC Type Reference

    Powertrain Diagnostic Trouble Code (DTC) Type Definitions

    Scan Tool Reference

    Control Module References for scan tool information

    CIRCUIT/SYSTEM VERIFICATION

    1. Engine running, observe the DTC information with a scan tool. DTCs P0016 and P0340 should not

    martes, 11 de agosto de 2020 11:49:39 a. m. Page 2 © 2011 Mitchell Repair Information Company, LLC.
    2008 Chevrolet Aveo LT
    2008 ENGINE Engine Controls and Fuel - 1.6L - Aveo, Swift+ (Canadian) & Wave (Canadian)

    set.
    2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You
    may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure
    Records data.

    CIRCUIT/SYSTEM TESTING

    1. Ignition OFF, disconnect the harness connector at the CMP sensor.


    2. Ignition ON, verify that a test lamp illuminates between the ignition 1 voltage circuit terminal 1 and
    ground.
    ¡ If the test lamp does not illuminate, test the ignition 1 voltage circuit for a short to ground or an
    open/high resistance. If the circuit tests normal and the ignition 1 voltage circuit fuse is open,
    test all components connected to the ignition 1 voltage circuit and replace as necessary.
    3. Connect a test lamp between the ground circuit terminal 2 and the ignition 1 voltage circuit terminal 1.
    Verify the test lamp illuminates.
    ¡ If the test lamp does not illuminate, repair the the ground circuit for an open/high resistance.

    4. Ignition ON, test for 4.8-5.2 volts between the signal circuit terminal 3 and the ground circuit terminal
    2.
    ¡ If less than the specified range, test the signal circuit for a short to ground or an open/high
    resistance. If the circuit tests normal, replace the ECM.
    ¡ If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests
    normal, replace the ECM.
    5. If all circuits test normal, test or replace the CMP sensor.

    REPAIR PROCEDURES

    Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    l Camshaft Position Sensor Replacement


    l Control Module References for ECM replacement, setup, and programming

    martes, 11 de agosto de 2020 11:49:39 a. m. Page 3 © 2011 Mitchell Repair Information Company, LLC.

    You might also like