INTEGRATED CIRCUITS

DATA SHEET

TJA1040
High speed CAN transceiver
Product specification 2003 Oct 14
Supersedes data of 2003 Feb 19
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

FEATURES GENERAL DESCRIPTION

• Fully compatible with the ISO 11898 standard The TJA1040 is the interface between the Controller Area
• High speed (up to 1 MBaud) Network (CAN) protocol controller and the physical bus.
It is primarily intended for high speed applications, up to
• Very low-current standby mode with remote wake-up
1 MBaud, in passenger cars. The device provides
capability via the bus
differential transmit capability to the bus and differential
• Very low ElectroMagnetic Emission (EME) receive capability to the CAN controller.
• Differential receiver with high common-mode range for The TJA1040 is the next step up from the TJA1050 high
ElectroMagnetic Immunity (EMI) speed CAN transceiver. Being pin compatible and offering
• Transceiver in unpowered state disengages from the the same excellent EMC performance, the TJA1040 also
bus (zero load) features:
• Input levels compatible with 3.3 V and 5 V devices • An ideal passive behaviour when supply voltage is off
• Voltage source for stabilizing the recessive bus level if • A very low-current standby mode with remote wake-up
split termination is used (further improvement of EME) capability via the bus.
• At least 110 nodes can be connected This makes the TJA1040 an excellent choice in nodes
• Transmit Data (TXD) dominant time-out function which can be in power-down or standby mode in partially
• Bus pins protected against transients in automotive powered networks.
environments
• Bus pins and pin SPLIT short-circuit proof to battery and
ground
• Thermally protected.

QUICK REFERENCE DATA

SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT

VCC supply voltage operating range 4.75 5.25 V
ICC supply current standby mode 5 15 µA
VCANH DC voltage on pin CANH 0 < VCC < 5.25 V; no time limit −27 +40 V
VCANL DC voltage on pin CANL 0 < VCC < 5.25 V; no time limit −27 +40 V
VSPLIT DC voltage on pin SPLIT 0 < VCC < 5.25 V; no time limit −27 +40 V
Vesd electrostatic discharge voltage Human Body Model (HBM)
pins CANH, CANL and SPLIT −6 +6 kV
all other pins −4 +4 kV
tPD(TXD-RXD) propagation delay TXD to RXD VSTB = 0 V 40 255 ns
Tvj virtual junction temperature −40 +150 °C

ORDERING INFORMATION

TYPE PACKAGE
NUMBER NAME DESCRIPTION VERSION
TJA1040T SO8 plastic small outline package; 8 leads; body width 3.9 mm SOT96-1
TJA1040U − bare die; die dimensions 1840 × 1440 × 380 µm −

2003 Oct 14 2
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

BLOCK DIAGRAM

handbook, full pagewidth VCC

1 TIME-OUT & 5
TEMPERATURE V SPLIT SPLIT
TXD
SLOPE PROTECTION
VCC
7
CANH
6
CANL
8 WAKE-UP DRIVER
STB
MODE CONTROL

4 WAKE-UP
RXD MUX
FILTER

2
TJA1040
GND

MGU161

Fig.1 Block diagram.

PINNING

SYMBOL PIN DESCRIPTION

TXD 1 transmit data input handbook, halfpage
GND 2 ground supply TXD 1 8 STB

VCC 3 supply voltage GND 2 7 CANH

TJA1040T
RXD 4 receive data output; reads out data VCC 3 6 CANL
from the bus lines
RXD 4 5 SPLIT
SPLIT 5 common-mode stabilization output
MGU160
CANL 6 LOW-level CAN bus line
CANH 7 HIGH-level CAN bus line
Fig.2 Pin configuration.
STB 8 standby mode control input

2003 Oct 14 3
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

FUNCTIONAL DESCRIPTION to the centre tap of the split termination (see Fig.4). In case
of a recessive bus voltage <0.5VCC due to the presence of
Operating modes
an unsupplied transceiver in the network with a significant
The TJA1040 provides two modes of operation which are leakage current from the bus lines to ground, the split
selectable via pin STB. See Table 1 for a description of the circuit will stabilize this recessive voltage to 0.5VCC. So a
modes of operation. start of transmission does not cause a step in the
common-mode signal which would lead to poor
Table 1 Operating modes ElectroMagnetic Emission (EME) behaviour.

PIN PIN RXD

MODE Wake-up
STB LOW HIGH In the standby mode the bus lines are monitored via a
normal LOW bus dominant bus recessive low-power differential comparator. Once the low-power
standby HIGH wake-up request no wake-up differential comparator has detected a dominant bus level
detected request detected for more than tBUS, pin RXD will become LOW.

NORMAL MODE Over-temperature detection

In this mode the transceiver is able to transmit and receive The output drivers are protected against over-temperature
data via the bus lines CANH and CANL. See Fig.1 for the conditions. If the virtual junction temperature exceeds the
block diagram. The differential receiver converts the shutdown junction temperature Tj(sd), the output drivers will
analog data on the bus lines into digital data which is be disabled until the virtual junction temperature becomes
output to pin RXD via the multiplexer (MUX). The slope of lower than Tj(sd) and TXD becomes recessive again.
the output signals on the bus lines is fixed and optimized By including the TXD condition, the occurrence of output
in a way that lowest ElectroMagnetic Emission (EME) is driver oscillation due to temperature drifts is avoided.
guaranteed.
TXD dominant time-out function
STANDBY MODE A ‘TXD dominant time-out’ timer circuit prevents the bus
In this mode the transmitter and receiver are switched off, lines from being driven to a permanent dominant state
and the low-power differential receiver will monitor the bus (blocking all network communication) if pin TXD is forced
lines. A HIGH level on pin STB activates this low-power permanently LOW by a hardware and/or software
receiver and the wake-up filter, and after tBUS the state of application failure. The timer is triggered by a negative
the CAN bus is reflected on pin RXD. edge on pin TXD.

The supply current on VCC is reduced to a minimum in If the duration of the LOW level on pin TXD exceeds the
such a way that ElectroMagnetic Immunity (EMI) is internal timer value (tdom), the transmitter is disabled,
guaranteed and a wake-up event on the bus lines will be driving the bus lines into a recessive state. The timer is
recognized. reset by a positive edge on pin TXD. The TXD dominant
time-out time tdom defines the minimum possible bit rate of
In this mode the bus lines are terminated to ground to 40 kBaud.
reduce the supply current (ICC) to a minimum. A diode is
added in series with the high-side driver of RXD to prevent Fail-safe features
a reverse current from RXD to VCC in the unpowered state.
In normal mode this diode is bypassed. This diode is not Pin TXD provides a pull-up towards VCC in order to force a
bypassed in standby mode to reduce current consumption. recessive level in case pin TXD is unsupplied.
Pin STB provides a pull-up towards VCC in order to force
Split circuit the transceiver into standby mode in case pin STB is
Pin SPLIT provides a DC stabilized voltage of 0.5VCC. It is unsupplied.
turned on only in normal mode. In standby mode pin SPLIT In the event that the VCC is lost, pins TXD, STB and RXD
is floating. The VSPLIT circuit can be used to stabilize the will become floating to prevent reverse supplying
recessive common-mode voltage by connecting pin SPLIT conditions via these pins.

2003 Oct 14 4
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 60134).
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
VCC supply voltage no time limit −0.3 +6 V
operating range 4.75 5.25 V
VTXD DC voltage on pin TXD −0.3 VCC + 0.3 V
VRXD DC voltage on pin RXD −0.3 VCC + 0.3 V
VSTB DC voltage on pins STB −0.3 VCC + 0.3 V
VCANH DC voltage on pin CANH 0 < VCC < 5.25 V; no time limit −27 +40 V
VCANL DC voltage on pin CANL 0 < VCC < 5.25 V; no time limit −27 +40 V
VSPLIT DC voltage on pin SPLIT 0 < VCC < 5.25 V; no time limit −27 +40 V
Vtrt transient voltages on pins CANH, according to ISO 7637; see Fig.5 −200 +200 V
CANL and SPLIT
Vesd electrostatic discharge voltage Human Body Model (HBM); note 1
pins CANH and CANL −6 +6 kV
and SPLIT
all other pins −4 +4 kV
Machine Model (MM); note 2 −200 +200 V
Tvj virtual junction temperature note 3 −40 +150 °C
Tstg storage temperature −55 +150 °C

Notes
1. Equivalent to discharging a 100 pF capacitor via a 1.5 kΩ series resistor.
2. Equivalent to discharging a 200 pF capacitor via a 0.75 µH series inductor and a 10 Ω series resistor.
3. Junction temperature in accordance with IEC 60747-1. An alternative definition of Tvj is: Tvj = Tamb + P × Rth(vj-amb),
where Rth(vj-amb) is a fixed value to be used for the calculating of Tvj. The rating for Tvj limits the allowable
combinations of power dissipation (P) and ambient temperature (Tamb).

THERMAL CHARACTERISTICS
In accordance with IEC 60747-1.
SYMBOL PARAMETER CONDITIONS VALUE UNIT
Rth(vj-a) thermal resistance from virtual junction in free air 145 K/W
to ambient in SO8 package
Rth(vj-s) thermal resistance from virtual junction in free air 50 K/W
to substrate of bare die

QUALITY SPECIFICATION
Quality specification in accordance with “AEC-Q100”.

2003 Oct 14 5
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

CHARACTERISTICS
VCC = 4.75 to 5.25 V, Tvj = −40 to +150 °C and RL = 60 Ω unless specified otherwise; all voltages are defined with
respect to ground; positive currents flow into the IC; note 1.
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Supply (pin VCC)
ICC supply current standby mode 5 10 15 µA
normal mode
recessive; VTXD = VCC 2.5 5 10 mA
dominant; VTXD = 0 V 30 50 70 mA
Transmit data input (pin TXD)
VIH HIGH-level input voltage 2 − VCC + 0.3 V
VIL LOW-level input voltage −0.3 − +0.8 V
IIH HIGH-level input current VTXD = VCC −5 0 +5 µA
IIL LOW-level input current normal mode; VTXD = 0 V −100 −200 −300 µA
Ci input capacitance not tested − 5 10 pF
Standby mode control input (pin STB)
VIH HIGH-level input voltage 2 − VCC + 0.3 V
VIL LOW-level input voltage −0.3 − +0.8 V
IIH HIGH-level input current VSTB = VCC − 0 − µA
IIL LOW-level input current VSTB = 0 V −1 −4 −10 µA
Receive data output (pin RXD)
VOH HIGH-level output voltage standby mode; VCC − 1.1 VCC − 0.7 VCC − 0.4 V
IRXD = −100 µA
IOH HIGH-level output current normal mode; −0.1 −0.4 −1 mA
VRXD = VCC − 0.4 V
IOL LOW-level output current VRXD = 0.4 V 2 6 12 mA
Common-mode stabilization output (pin SPLIT)
VO output voltage normal mode; 0.3VCC 0.5VCC 0.7VCC V
−500 µA < IO < +500 µA
IL leakage current standby mode; − 0 5 µA
−22 V < VSPLIT < +35 V
Bus lines (pins CANH and CANL)
VO(dom) dominant output voltage VTXD = 0 V
pin CANH 3 3.6 4.25 V
pin CANL 0.5 1.4 1.75 V
VO(dom)(m) matching of dominant output −100 0 +150 mV
voltage (VCC - VCANH - VCANL)
VO(dif)(bus) differential bus output voltage VTXD = 0 V; dominant; 1.5 − 3.0 V
(VCANH − VCANL) 45 Ω < RL < 65 Ω
VTXD = VCC; recessive; −50 − +50 mV
no load

2003 Oct 14 6
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

VO(reces) recessive output voltage normal mode; VTXD = VCC; 2 0.5VCC 3 V
no load
standby mode; no load −0.1 0 +0.1 V
IO(sc) short-circuit output current VTXD = 0 V
pin CANH; VCANH = 0 V −40 −70 −95 mA
pin CANL; VCANL = 40 V 40 70 100 mA
IO(reces) recessive output current −27 V < VCAN < +32 V −2.5 − +2.5 mA
Vdif(th) differential receiver threshold −12 V < VCANL < +12 V;
voltage −12 V < VCANH < +12 V
normal mode (see Fig.6) 0.5 0.7 0.9 V
standby mode 0.4 0.7 1.15 V
Vhys(dif) differential receiver hysteresis normal mode; 50 70 100 mV
voltage −12 V < VCANL < +12 V;
−12 V < VCANH < +12 V
ILI input leakage current VCC = 0 V; −5 0 +5 µA
VCANH = VCANL = 5 V
Ri(cm) common-mode input standby or normal mode 15 25 35 kΩ
resistance
Ri(cm)(m) common-mode input VCANH = VCANL −3 0 +3 %
resistance matching
Ri(dif) differential input resistance standby or normal mode 25 50 75 kΩ
Ci(cm) common-mode input VTXD = VCC; not tested − − 20 pF
capacitance
Ci(dif) differential input capacitance VTXD = VCC; not tested − − 10 pF
Timing characteristics; see Fig.8
td(TXD-BUSon) delay TXD to bus active normal mode 25 70 110 ns
td(TXD-BUSoff) delay TXD to bus inactive 10 50 95 ns
td(BUSon-RXD) delay bus active to RXD 15 65 115 ns
td(BUSoff-RXD) delay bus inactive to RXD 35 100 160 ns
tPD(TXD-RXD) propagation delay TXD to RXD VSTB = 0 V 40 − 255 ns
tdom(TXD) TXD dominant time-out VTXD = 0 V 300 600 1000 µs
tBUS dominant time for wake-up via standby mode 0.75 1.75 5 µs
bus
td(stb-norm) delay standby mode to normal normal mode 5 7.5 10 µs
mode
Thermal shutdown
Tj(sd) shutdown junction temperature 155 165 180 °C
Note
1. All parameters are guaranteed over the virtual junction temperature range by design, but only 100% tested at 125 °C
ambient temperature for dies on wafer level, and in addition to this 100% tested at 25 °C ambient temperature for
cased products; unless specified otherwise. For bare dies, all parameters are only guaranteed with the backside of
the die connected to ground.

2003 Oct 14 7
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

APPLICATION AND TEST INFORMATION

handbook, full pagewidth

BAT 5V

VCC
CANH 3 STB VCC
7 8 Port x

TJA1040
SPLIT MICROCONTROLLER
5

RXD
4 RXD
CANL TXD
6 1 TXD
2
MGU164

More application information is available in a separate application note.

Fig.3 Typical application for 5 V microcontroller.

handbook, full pagewidth

VCC

TJA1040
CANH

R 60 Ω
VSPLIT = 0.5VCC
SPLIT
in normal mode;
otherwise floating
R 60 Ω
CANL

MGU162
GND

Fig.4 Stabilization circuitry and application.

2003 Oct 14 8
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

handbook, full pagewidth +5 V

47 µF 100 nF
VCC

3 1 nF
TXD CANH
1 7
TRANSIENT
1 nF GENERATOR
CANL
500 kHz TJA1040 6

SPLIT
RXD 5
4
2 8
15 pF GND STB

MGW336

The waveforms of the applied transients will be in accordance with ISO 7637 part 1, test pulses 1, 2, 3a, 3b, 5, 6 and 7.

Fig.5 Test circuit for automotive transients.

handbook, full pagewidth MGS378

VRXD

HIGH

LOW

hysteresis

0.5 0.9 Vi(dif)(bus) (V)

Fig.6 Hysteresis of the receiver.

2003 Oct 14 9
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

handbook, full pagewidth +5 V

47 µF 100 nF
VCC

3
TXD
1
CANH
7
SPLIT RL CL
5 TJA1040
60 Ω 100 pF
CANL
RXD 6
4
2 8
15 pF GND STB

MGW335

Fig.7 Test circuit for timing characteristics.

HIGH
handbook, full pagewidth
TXD
LOW

CANH

CANL

dominant
(BUS on)
0.9 V
Vi(dif)(bus) (1)
0.5 V
recessive
(BUS off)
HIGH
0.7VCC
RXD 0.3VCC
LOW
t d(TXD-BUSon) t d(TXD-BUSoff)
t d(BUSon-RXD) t d(BUSoff-RXD)

t PD(TXD-RXD) t PD(TXD-RXD) MGS377

(1) Vi(dif)(bus) = VCANH − VCANL.

Fig.8 Timing diagram.

2003 Oct 14 10
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

BONDING PAD LOCATIONS

COORDINATES(1)
SYMBOL PAD
x y handbook, halfpage 8 7 6 5

TXD 1 119.5 114.5

GND 2 648.5 85
test pad 1
VCC 3 1214.25 114.5
TJA1040U
RXD 4 1635.25 114.5 test pad 2

SPLIT 5 1516.5 1275

CANL 6 990.5 1273.75 x
CANH 7 530.25 1273.75 0 1 2 3 4
0
MBL584
STB 8 113.75 1246 y

Note
The backside of the bare die must be connected to ground.
1. All x/y coordinates represent the position of the centre
of each pad (in µm) with respect to the left hand Fig.9 Bonding pad locations.
bottom corner of the top aluminium layer (see Fig.9).

2003 Oct 14 11
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

PACKAGE OUTLINE
SO8: plastic small outline package; 8 leads; body width 3.9 mm SOT96-1

D E A
X

y HE v M A

8 5

Q
A2
(A 3) A
A1
pin 1 index
θ
Lp

1 4 L

e w M detail X
bp

0 2.5 5 mm
scale

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

A
UNIT max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) θ

0.25 1.45 0.49 0.25 5.0 4.0 6.2 1.0 0.7 0.7
mm 1.75 0.25 1.27 1.05 0.25 0.25 0.1 o
0.10 1.25 0.36 0.19 4.8 3.8 5.8 0.4 0.6 0.3 8
0.010 0.057 0.019 0.0100 0.20 0.16 0.244 0.039 0.028 0.028 0o
inches 0.069 0.01 0.05 0.041 0.01 0.01 0.004
0.004 0.049 0.014 0.0075 0.19 0.15 0.228 0.016 0.024 0.012

Notes
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
2. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.

OUTLINE REFERENCES EUROPEAN

ISSUE DATE
VERSION IEC JEDEC JEITA PROJECTION

99-12-27
SOT96-1 076E03 MS-012
03-02-18

2003 Oct 14 12
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

SOLDERING To overcome these problems the double-wave soldering

method was specifically developed.
Introduction to soldering surface mount packages
If wave soldering is used the following conditions must be
This text gives a very brief insight to a complex technology.
observed for optimal results:
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages” • Use a double-wave soldering method comprising a
(document order number 9398 652 90011). turbulent wave with high upward pressure followed by a
smooth laminar wave.
There is no soldering method that is ideal for all surface
• For packages with leads on two sides and a pitch (e):
mount IC packages. Wave soldering can still be used for
certain surface mount ICs, but it is not suitable for fine pitch – larger than or equal to 1.27 mm, the footprint
SMDs. In these situations reflow soldering is longitudinal axis is preferred to be parallel to the
recommended. transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
Reflow soldering must be parallel to the transport direction of the
Reflow soldering requires solder paste (a suspension of printed-circuit board.
fine solder particles, flux and binding agent) to be applied The footprint must incorporate solder thieves at the
to the printed-circuit board by screen printing, stencilling or downstream end.
pressure-syringe dispensing before package placement. • For packages with leads on four sides, the footprint must
Driven by legislation and environmental forces the be placed at a 45° angle to the transport direction of the
worldwide use of lead-free solder pastes is increasing. printed-circuit board. The footprint must incorporate
Several methods exist for reflowing; for example, solder thieves downstream and at the side corners.
convection or convection/infrared heating in a conveyor During placement and before soldering, the package must
type oven. Throughput times (preheating, soldering and be fixed with a droplet of adhesive. The adhesive can be
cooling) vary between 100 and 200 seconds depending applied by screen printing, pin transfer or syringe
on heating method. dispensing. The package can be soldered after the
Typical reflow peak temperatures range from adhesive is cured.
215 to 270 °C depending on solder paste material. The Typical dwell time of the leads in the wave ranges from
top-surface temperature of the packages should 3 to 4 seconds at 250 °C or 265 °C, depending on solder
preferably be kept: material applied, SnPb or Pb-free respectively.
• below 220 °C (SnPb process) or below 245 °C (Pb-free
A mildly-activated flux will eliminate the need for removal
process)
of corrosive residues in most applications.
– for all BGA and SSOP-T packages
– for packages with a thickness ≥ 2.5 mm Manual soldering
– for packages with a thickness < 2.5 mm and a Fix the component by first soldering two
volume ≥ 350 mm3 so called thick/large packages. diagonally-opposite end leads. Use a low voltage (24 V or
• below 235 °C (SnPb process) or below 260 °C (Pb-free less) soldering iron applied to the flat part of the lead.
process) for packages with a thickness < 2.5 mm and a Contact time must be limited to 10 seconds at up to
volume < 350 mm3 so called small/thin packages. 300 °C.

Moisture sensitivity precautions, as indicated on packing, When using a dedicated tool, all other leads can be
must be respected at all times. soldered in one operation within 2 to 5 seconds between
270 and 320 °C.
Wave soldering
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.

2003 Oct 14 13
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

Suitability of surface mount IC packages for wave and reflow soldering methods

SOLDERING METHOD
PACKAGE(1)
WAVE REFLOW(2)
BGA, LBGA, LFBGA, SQFP, SSOP-T(3), TFBGA, VFBGA not suitable suitable
DHVQFN, HBCC, HBGA, HLQFP, HSQFP, HSOP, HTQFP, not suitable(4) suitable
HTSSOP, HVQFN, HVSON, SMS
PLCC(5), SO, SOJ suitable suitable
LQFP, QFP, TQFP not recommended(5)(6) suitable
SSOP, TSSOP, VSO, VSSOP not recommended(7) suitable
PMFP(8) not suitable not suitable

Notes
1. For more detailed information on the BGA packages refer to the “(LF)BGA Application Note” (AN01026); order a copy
from your Philips Semiconductors sales office.
2. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum
temperature (with respect to time) and body size of the package, there is a risk that internal or external package
cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the
Drypack information in the “Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods”.
3. These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no account
be processed through more than one soldering cycle or subjected to infrared reflow soldering with peak temperature
exceeding 217 °C ± 10 °C measured in the atmosphere of the reflow oven. The package body peak temperature
must be kept as low as possible.
4. These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder
cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink on the top side,
the solder might be deposited on the heatsink surface.
5. If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave direction.
The package footprint must incorporate solder thieves downstream and at the side corners.
6. Wave soldering is suitable for LQFP, TQFP and QFP packages with a pitch (e) larger than 0.8 mm; it is definitely not
suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
7. Wave soldering is suitable for SSOP, TSSOP, VSO and VSSOP packages with a pitch (e) equal to or larger than
0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
8. Hot bar or manual soldering is suitable for PMFP packages.

REVISION HISTORY

REV DATE CPCN DESCRIPTION

6 20031014 200307014 Product specification (9397 750 11837)
Modification:
• Change ‘Vth(dif) = 0.5 V’ in standby mode into ‘Vdif(th) = 0.4 V’
• Add Chapter REVISION HISTORY
5 20030219 − Product specification (9397 750 10887)

2003 Oct 14 14
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

DATA SHEET STATUS

DATA SHEET PRODUCT

LEVEL DEFINITION
STATUS(1) STATUS(2)(3)
I Objective data Development This data sheet contains data from the objective specification for product
development. Philips Semiconductors reserves the right to change the
specification in any manner without notice.
II Preliminary data Qualification This data sheet contains data from the preliminary specification.
Supplementary data will be published at a later date. Philips
Semiconductors reserves the right to change the specification without
notice, in order to improve the design and supply the best possible
product.
III Product data Production This data sheet contains data from the product specification. Philips
Semiconductors reserves the right to make changes at any time in order
to improve the design, manufacturing and supply. Relevant changes will
be communicated via a Customer Product/Process Change Notification
(CPCN).
Notes
1. Please consult the most recently issued data sheet before initiating or completing a design.
2. The product status of the device(s) described in this data sheet may have changed since this data sheet was
published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com.
3. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.

DEFINITIONS DISCLAIMERS
Short-form specification  The data in a short-form Life support applications  These products are not
specification is extracted from a full data sheet with the designed for use in life support appliances, devices, or
same type number and title. For detailed information see systems where malfunction of these products can
the relevant data sheet or data handbook. reasonably be expected to result in personal injury. Philips
Semiconductors customers using or selling these products
Limiting values definition  Limiting values given are in
for use in such applications do so at their own risk and
accordance with the Absolute Maximum Rating System
agree to fully indemnify Philips Semiconductors for any
(IEC 60134). Stress above one or more of the limiting
damages resulting from such application.
values may cause permanent damage to the device.
These are stress ratings only and operation of the device Right to make changes  Philips Semiconductors
at these or at any other conditions above those given in the reserves the right to make changes in the products -
Characteristics sections of the specification is not implied. including circuits, standard cells, and/or software -
Exposure to limiting values for extended periods may described or contained herein in order to improve design
affect device reliability. and/or performance. When the product is in full production
(status ‘Production’), relevant changes will be
Application information  Applications that are
communicated via a Customer Product/Process Change
described herein for any of these products are for
Notification (CPCN). Philips Semiconductors assumes no
illustrative purposes only. Philips Semiconductors make
responsibility or liability for the use of any of these
no representation or warranty that such applications will be
products, conveys no licence or title under any patent,
suitable for the specified use without further testing or
copyright, or mask work right to these products, and
modification.
makes no representations or warranties that these
products are free from patent, copyright, or mask work
right infringement, unless otherwise specified.

2003 Oct 14 15
Philips Semiconductors Product specification

High speed CAN transceiver TJA1040

Bare die  All die are tested and are guaranteed to

comply with all data sheet limits up to the point of wafer
sawing for a period of ninety (90) days from the date of
Philips' delivery. If there are data sheet limits not
guaranteed, these will be separately indicated in the data
sheet. There are no post packing tests performed on
individual die or wafer. Philips Semiconductors has no
control of third party procedures in the sawing, handling,
packing or assembly of the die. Accordingly, Philips
Semiconductors assumes no liability for device
functionality or performance of the die or systems after
third party sawing, handling, packing or assembly of the
die. It is the responsibility of the customer to test and
qualify their application in which the die is used.

2003 Oct 14 16
Philips Semiconductors – a worldwide company

Contact information

For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825

For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com.

© Koninklijke Philips Electronics N.V. 2003 SCA75

All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.

Printed in The Netherlands R16/06/pp17 Date of release: 2003 Oct 14 Document order number: 9397 750 11837
TJA1040 - High-speed CAN transceiver with standby mode from NXP Semiconductors Page 1 of 5

Select site: English

Home About NXP News Careers Investors Order/buy Support Contact my.NXP Type search here Search

Advanced search / Selection guides

Products ... Transceivers and fail-safe System Basis Chips High-speed CAN transceivers TJA1040T Applications Looking for

TJA1040 Preview Product information Selection guide See also

Datasheet See the answers to FAQ's on certain

TJA1040 - High-speed CAN transceiver with standby mode fields of interest
TJA1040 General description Pricing/ordering/availability Design support Find NXP's equivalent of a competitor's
(Product Specification) Features Samples Parametrics/similar products part number
14-Oct-03, 17 Pages, 91kB Products/packages Discontinued information Print/email View case studies on general
Quality/reliability/chemical Applications Disclaimers applications or technologies
content Block diagrams/pinning
Download datasheet Request contact with a technical expert
Download all documentation All information hereunder is subject to the subsequent disclaimers Find more information on NXP's Vision
Find out more about our ordering
process
Receive e-news on specific interest
areas
General description Hide

The TJA1040 is the interface between the Controller Area Network (CAN) protocol controller and the physical bus. It is primarily intended
for high speed applications, up to 1 MBaud, in passenger cars. The device provides differential transmit capability to the bus and differential receive capability to the CAN controller.

The TJA1040 is the next step up from the TJA1050 high speed CAN transceiver. Being pin compatible and offering the same excellent EMC performance, the TJA1040 also features:

An ideal passive behaviour when supply voltage is off

A very low-current standby mode with remote wake-upcapability via the bus.

This makes the TJA1040 an excellent choice in nodes which can be in power-down or standby mode in partially powered networks.

Back to top

Features Hide

Fully compatible with the ISO 11898 standard

High speed (up to 1 MBaud)
Very low-current standby mode with remote wake-up capability via the bus
Very low ElectroMagnetic Emission (EME)
Differential receiver with high common-mode range for ElectroMagnetic Immunity (EMI)
Transceiver in unpowered state disengages from the bus (zero load)
Input levels compatible with 3.3 V and 5 V devices
Voltage source for stabilizing the recessive bus level if split termination is used (further improvement of EME)
At least 110 nodes can be connected
Transmit Data (TXD) dominant time-out function
Bus pins protected against transients in automotive environments
Bus pins and pin SPLIT short-circuit proof to battery and ground
Thermally protected.

http://www.nxp.com/ 21-Oct-2009
TJA1040 - High-speed CAN transceiver with standby mode from NXP Semiconductors Page 2 of 5

Back to top

Products/packages Hide

Type number Orderable part number Ordering code (12NC) Product status Package Packing Marking ECCN
TJA1040T/V TJA1040T/V,112 9352 853 53112 Volume production SOT96 Tube Standard Marking
TJA1040T/V TJA1040T/V,118 9352 853 53118 Volume production SOT96 Reel Pack, SMD, 13" Standard Marking
TJA1040T/V TJA1040T/V,518 9352 853 53518 Volume production SOT96 Reel Dry Pack, SMD, 13" Standard Marking
TJA1040T/VM TJA1040T/VM,112 9352 879 61112 Volume production SOT96 Tube Standard Marking
TJA1040T/VM TJA1040T/VM,118 9352 879 61118 Volume production SOT96 Reel Pack, SMD, 13" Standard Marking
TJA1040T/VM TJA1040T/VM,518 9352 879 61518 Volume production SOT96 Reel Dry Pack, SMD, 13" Standard Marking

The variants in the table below are discontinued. See the table Discontinued information for more information.

Type number Orderable part number Ordering code (12NC) Product status Package Packing Marking ECCN
Discontinued
TJA1040T/N1 TJA1040T/N1,112 9352 687 35112 SOT96 Tube Standard Marking
Replacement product
Discontinued
TJA1040T/N1 TJA1040T/N1,118 9352 687 35118 SOT96 Reel Pack, SMD, 13" Standard Marking
Replacement product
Discontinued
TJA1040T/N1 TJA1040T/N1,518 9352 687 35518 SOT96 Reel Dry Pack, SMD, 13" Standard Marking
Replacement product

Back to top

Quality/reliability/chemical content Hide

Type number Orderable part number Chemical content RoHS Leadfree conversion date RHF IFR (FIT) MTBF (hours) MSL
TJA1040T/V TJA1040T/V,112 TJA1040T_V Always Pb-free

TJA1040T/V TJA1040T/V,118 TJA1040T_V Always Pb-free

TJA1040T/V TJA1040T/V,518 TJA1040T_V Always Pb-free

TJA1040T/VM TJA1040T/VM,112 TJA1040T_VM Always Pb-free

TJA1040T/VM TJA1040T/VM,118 TJA1040T_VM Always Pb-free

TJA1040T/VM TJA1040T/VM,518 TJA1040T_VM Always Pb-free

The variants in the table below are discontinued. See the table Discontinued information for more information.

Type number Orderable part number Chemical content RoHS Leadfree conversion date RHF IFR (FIT) MTBF (hours) MSL
TJA1040T/N1 TJA1040T/N1,112 TJA1040T_N1 week 3, 2005

TJA1040T/N1 TJA1040T/N1,118 TJA1040T_N1 week 3, 2005

TJA1040T/N1 TJA1040T/N1,518 TJA1040T_N1 Always Pb-free

Quality and reliability disclaimer

Back to top

http://www.nxp.com/ 21-Oct-2009
TJA1040 - High-speed CAN transceiver with standby mode from NXP Semiconductors Page 3 of 5

Pricing/ordering/availability Hide

Type number Ordering code Orderable part Indicative price/unit Region Distributor In Order Inventory Buy Samples
(12NC) number ($) stock quantity date online
not
TJA1040T/V 9352 853 53112 TJA1040T/V,112
available
not
TJA1040T/V 9352 853 53118 TJA1040T/V,118
available
not
TJA1040T/V 9352 853 53518 TJA1040T/V,518
available
not
TJA1040T/VM 9352 879 61112 TJA1040T/VM,112
available
not
TJA1040T/VM 9352 879 61118 TJA1040T/VM,118
available
not
TJA1040T/VM 9352 879 61518 TJA1040T/VM,518
available

Back to top

Discontinued information Hide

Type Ordering code Last-time Last-time Replacement DN Status Comments

number (12NC) buy date delivery date product Notice
Sole source product
Limited Availability. FAB ICN5 Closure. Refer to
Limited availability (check
TJA1040T/N1 935268735112 31-dec-09 30-jun-10 TJA1040T/VM DN 64 PCN200901054F dated February 12, 2009. Replacement
with your usual sales
type with new diffusion fab location only.
contact)
Sole source product
Limited Availability. FAB ICN5 Closure. Refer to
Limited availability (check
TJA1040T/N1 935268735118 31-dec-09 30-jun-10 TJA1040T/VM DN 64 PCN200901054F dated February 12, 2009. Replacement
with your usual sales
type with new diffusion fab location only.
contact)
Sole source product
Limited Availability. FAB ICN5 Closure. Refer to
Limited availability (check
TJA1040T/N1 935268735518 31-dec-09 30-jun-10 TJA1040T/VM DN 64 PCN200901054F dated February 12, 2009. Replacement
with your usual sales
type with new diffusion fab location only.
contact)

Back to top

Block diagrams/pinning Hide

http://www.nxp.com/ 21-Oct-2009
TJA1040 - High-speed CAN transceiver with standby mode from NXP Semiconductors Page 4 of 5

Back to top

Design support Hide

Application Notes
AN10211_2;TJA1040 high speed CAN transceiver (2006-11-10)
AN00094_3;TJA1041/1041A high speed CAN transceiver (2006-11-08)
AN00020_2;TJA1050 high speed CAN transceiver (2006-11-10)

Support Documents
75015744; High-speed CAN transceivers TJA104x, JA1050 and PCA82C25x (2006-09-01)
75016161; NXP Automotive networking solutions (2007-09-01)
75015741; The vital link in the interconnected car (2006-09-01)
PCA82C250_251_TJA1040_TJA1050; Upgrading Note PCA82C250/251 -> TJA1040, TJA1050 (2001-11-20)

Back to top

Parametrics/similar products Hide

Type Package Supply Application Configuration CATEGORY FEATURES FUNCTION Operating No. of Package Transceiver
number voltage temp. Pins Material Type
(V) (Cel)
ISO compliant, standby mode,
4.75 ~ Control HS-CAN CAN -40 ~ SO8, bare
TJA1040T/N1 SOT96 transceiver remote wake-up, invisible 8 High Speed
5.25 Devices transceiver Transceivers +125 die
when off
ISO compliant, standby mode,
4.75 ~ HS-CAN -40 ~ SO8, bare
TJA1040T/V SOT96 transceiver remote wake-up, invisible 8
5.25 transceiver +125 die
when off

Similar products
TJA1040 links to the similar products page containing an overview of products that are similar in function or related to the type number(s) as listed on this page. The similar products page
includes products from the same catalog tree(s), relevant selection guides and products from the same functional category.

http://www.nxp.com/ 21-Oct-2009
TJA1040 - High-speed CAN transceiver with standby mode from NXP Semiconductors Page 5 of 5

Back to top

Print/email Hide

Email this product information

Print this product information

Back to top

Disclaimers Hide

General product disclaimer

Quality and reliability disclaimer

NXP | Privacy policy | Terms of use | Sitemap | Switch to classic mode

©2006-2009 NXP Semiconductors. All rights reserved.

http://www.nxp.com/ 21-Oct-2009