CODE SN113-0005-00

DATE 2012.12.10

SPECIFICATION
MODEL : HYD. CRAWLER DRILL
(JD – 1300E)

CUSTOMER :
 JD – 1300E SN113-0005-00

1. General Description
JUNJIN CSM hydraulic crawler drill is a drilling machine for blasting with
dynamite in the quarries, and mining and construction site. It is mainly
composed of Traveling device as a base machine, Drifter, Guide shell,
loading device as drilling device, power unit and running device operated
by diesel engine. Differently from pneumatic drill, Air compressor and dust
collector installed on the power unit make a high efficient rock drilling with
low noise as much as possible.

2. Design assembly

FUEL TANK

1
www.junjincsm.com
JD – 1300E SN113-0005-00

2
www.junjincsm.com
JD – 1300E SN113-0005-00

3
www.junjincsm.com
JD – 1300E SN113-0005-00

4. Features

1) Powerful Drifter JET-9

Drifter model JET-9 with hydraulic hammering system and hydraulic
motor easily and speedily performs Drilling Φ 76~Φ 127 by hammering,
rotating and flushing the debris in the hole. Its simple and practical
components are different from the others.
① Special seals adopted in the front and rear of the piston enhance
its durability.
② Highly increased hammering energy increased drilling speed.
③ Chuck made of special alloy increases durability.

2) Working safety
① Tumbler length 2480mm and shoe width 330mm maximizes safety.
② Ground clearance (510mm) and track oscillation (±10°)on either
side prevent the bottom from being damaged by projection on the
rough zone.

3) Anti-jamming system
Makes the stable operation possible on all kind of rock and makes an
easy operations by an unskilled operator. This will be operated only in
case the anti-jamming switch is on position.

4) Collaring
Collaring makes it easy to take a correct position for drilling and an
unskilled operator performs drilling correctly.

5) Traveling speed and gradeability

The piston pump and traveling motor with high efficiency maximize its
traveling speed and gradeability-Traveling speed : 3.3km/h ;
Max. Grade ability: 28°

4
www.junjincsm.com
JD – 1300E SN113-0005-00

6) Maintenance and inspection

Panel typed bonnet and vertical typed fuel tank make more room for
checking and services.
The oil drain cocks installed on either side for engine oil, gear box oil,
fuel, compressor oil make the oil exchange and cleaning easy.

7) Powerful Dust Collector

① Dust collector with 4 filters prevents dust from flying in drilling and
its filters are protected by air flushing in each filter.
② To prevent the filter from being damaged by a water vein, shutter
installed within stop collecting dust in case a water vein appears
during drilling.

8) Comfortable and safe Cabin

Strong frame, safety glass on all directions, and safety net protect the
operator and provide secure broad view in job site. Floating typed
operators seat with air-bellows protects the operator from vibration and
provides very comfortable working conditions. Air condition, radio, and
the heater are provided as basic specifications.

9) Sliding Suction Hood

With suction hood cab slided up and down by the operator in the cabin,
the operator con performs drilling without others assistance correctly.
The hood stuck to the ground prevents the debris from flying in drilling.

10) Auto Lubrication for Drifter

Lubricator part and an oil tank are installed to refuel the Drifter Front Part
(gear box). The flow rate of the Lubricator has automatically supplied
from an oil tank.
The automatic lubrication system removes the inconvenience of
feeding oil frequently and protects the drifter from being damaged by
lubrication oil shortage.

5
www.junjincsm.com
JD – 1300E SN113-0005-00

11) Centralized Electric Control System

All the electric control devices are centralized in the control box for
checking any trouble easily.

12) Pre-Cleaner (Cyclone)-Optional Parts

Pre-cleaner installed between hood and dust collector protects the filters
in the dust collector and the hose from being damaged by the debris.

13) Auto Grease System

Before the rod and the sleeve connected, greases the external screw by
only pushing the button, which helps the rod and the sleeve charged
tightly to get easily loosed.

14) Auto Rod Changer (ARC)

The operator connects or disconnects the rods by controlling only a
few levers in the cabin without an assistant.
This automatic rod exchange can be performed by means of sequential
hydraulic schematic.
7 Rods(including the first rod) can be equipped in the cartridge of ARC

15) Cummins Engine with large output

Cummins engine with water cooling system supply sufficient power for
traveling or operating at job site. Especially its world wide services
network by Cummins will be a good point for the users.

16) Large Fuel Tank

Fuel tank can hold 405 liters and gives comparatively a long operating
duration.
The residual fuel can be observed in sight unless engine room opened.

6
www.junjincsm.com
JD – 1300E SN113-0005-00

17) Compressor On/Off Switch

Air compressor can be used only in case compressed air required by
On/Off switch. The On/Off switch of compressor is effective to cut
down the engine fuel consumption by unloading the compressor at the
Off position.

7
www.junjincsm.com
JD – 1300E SN113-0005-00

5. Specifications
MODEL
NO ITEM
JD-1300E
Gross weight kg 14,700
Overall length mm 9,400
Overall
1 Overall width mm 2,420(2,890)
Dimensions
Overall height mm 2,940
Ground clearance mm 510
Hole range mm Φ 76~Φ 127
Performanc
2 Gradeabillity ° 28
e
Traveling speed km/h 0 ~ 3.3
Model CTAA8.3-C (CUMMINS)
3 Engine Rated output ps/rpm 205 / 2,200
Oscillating Angle ° ±10
Model JET-9 YH-80
Total Length Mm 1,148 1,025
Total Width Mm 379 360
Total Height Mm 297 295
Weight Kgf 270 210
4 Drifter Impact Frequency Hz 35~50 40~45
Rotational Torque Kgf-m Max. 88 Max. 59
Rotational Frequency RPM Max. 180 Max. 150
Impact Pressure Bar Max. 150 Max. 140
Rotation Pressure Bar Max. 140 Max. 140
Flusing Pressure Bar Max. 10.5 Max. 10.5
Model CF90G5
2
Air Working pressure kg/cm 10.5
5
compressor Free air delivery m3 7.8
3
Tank capacity m 0.051
Overall length mm 7,290
Slide length mm 1,500
6 Guide Feed length mm 4,300
Swing angle R/L。 30 /90
Tilt angle 。 180

8
www.junjincsm.com
JD – 1300E SN113-0005-00

MODEL
NO ITEM
JD-1300E
Overall length mm 3,000
Lift angle U/D。 50/25
7 Boom
Swing angle R/L。 35/25
Slide length mm 1,100
Suction capacity m3/min 20
Dust
8 Number of filters EA 4
collector
Blow pressure mm/Aq 600
Under Length of tumbler mm 2,480
9
carriage Shoe width mm 330
Length of rod mm 3,660
10 Tool Bit dia. mm Φ 76~Φ 127
Rod section mm R45, R51(*)
Variable piston pump
11 Hyd. sys. Hyd. pump
+ Gear pump
Auto rod Type ○
12
changer Number of Rod EA 6 + 1 (*5+1)
13 CABIN ROPS & FOPS STD

9
www.junjincsm.com
JD – 1300E SN113-0005-00

6. Specification Diagram

10
www.junjincsm.com
JD – 1300E SN113-0005-00

JD-1300E MAIN PARTS 1/3

DRIFTER
MODEL : JET-9
MAKER : JUNJIN CSM (KOREA)

11
www.junjincsm.com
JD – 1300E SN113-0005-00

JD-1300E MAIN PARTS

TRAVEL MOTOR
MODEL : TM18VC-A-80
TONGMYUNG HEAVY INDERSTRIES CO.LTD

LINK ASS’ Y

1. LINK
MODEL : P154x45 LINK
MAKER : HANBACK PRECISION COMPANY (KOREA)
2. SHOE PLATE
MODEL : SINGLE
MAKER : INTERTRACK (GERMANY)

12
www.junjincsm.com
JD – 1300E SN113-0005-00

JD-1300E MAIN PARTS

13
www.junjincsm.com