JP4

 series

Product Segments TiMOTION’s JP4 series inline linear actuator is most similar to the JP3,
but was designed for industrial applications that require higher load and
• Industrial Motion speed. Its IP69K protection ensures it will withstand high temperature, high
pressure water jets, and the ingress of dust and other solid contaminants. For
synchronization and position feedback, the JP4 can be equipped with Hall
sensors.

General Features

Voltage of motor 12/24V DC, or 12/24V DC (PTC)

Maximum load 4,500N in push
Maximum load 3,000N in pull
Maximum speed at full load 24mm/s (with 500N in a push or pull
condition)
Stroke ≥ 20~1000mm
Minimum installation dimension ≥ Stroke + 289mm
IP rating Up to IP69K
Color Black or grey
Certificate UL73
Operational temperature range -5°C~+65°C
Operational temperature range +5°C~+45°C
at full performance
Storage temperature range -40°C~+70°C
An inline actuator designed for small spaces

1
series
JP4 Drawing
Retracted Length
Standard Dimensions
14.9 ø10.2
(mm)

4.2
ø28.5
51
ø13

Load and Speed

CODE Load (N) Self Locking Typical Current (A) Typical Speed (mm/s)
Force (N)
Push Pull No Load With Load No Load With Load
24V DC 24V DC 24V DC 24V DC

Motor Speed (3800RPM, Duty Cycle 10%)

B 4500 3000 4500 1.1 4.0 4.4 2.5
C 3500 3000 3000 1.1 4.0 6.5 4.0
D 2500 2500 2000 1.1 4.0 9.2 5.6
E 1500 1500 1000 1.1 3.0 12.0 9.5
F 1000 1000 700 1.1 3.0 18.0 14.0
G 500 500 500 1.1 3.0 27.5 24.0

Note
1 Please refer to the approved drawing for the final authentic value.

2 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control
boxes have this feature built-in.

3 The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current
measured in 24V DC; speed will be similar for both voltages.

4  The current & speed in table are tested when the actuator is extending under push load.

5  The current & speed in table and diagram are tested with a stable 24V DC power supply.

6 Standard stroke: Min. ≥ 20mm, Max. please refer to below table

CODE Load (N) Max Stroke (mm)

B 4500 400

C 3500 500

D 2500 600

E 1500 700

F 1000 800

G 500 1000

2
series
JP4 Performance Data (24V DC Motor)

Motor Speed (3800RPM, Duty Cycle 10%)

Speed vs. Load

30.0

G
25.0
Speed (mm/s)

20.0

F
15.0

E
10.0

D
5.0 C
B

0.0
0 1000 2000 3000 4000 5000

Load (N)

Current vs. Load

D C B
4.0

3.5

G F E
3.0
Current (A)

2.5

2.0

1.5

1.0
0 1000 2000 3000 4000 5000

Load (N)

3
JP4 Ordering Key
JP4 Version: 20191204-F

Voltage 1 = 12V DC 2 = 24V DC 5 = 24V DC, PTC 6 = 12V DC, PTC

See page 7
Load and Speed See page 2

Stroke (mm)

Retracted Length See page 2

(mm)

Rear Attachment 1 = Aluminum casting, U clevis, slot 4.2, depth 18.0, hole 10.2
(mm)
See page 6
Front Attachment 1 = Aluminum CNC, no slot, hole 13.0
(mm)
See page 6
Direction of 1 = 0°
Rear Attachment
(Counterclockwise)
See page 6
Color 1 = Black 2 = Grey (Pantone 428C)

IP Rating 1 = Without 3 = IP66 6 = IP66D 8 = IP69K

2 = IP54 5 = IP66W 7 = IP68

Special Functions 0 = Without (Standard)

for Spindle Sub-
Assembly
Functions for 1 = Two switches at full retracted / extended positions to cut current
Limit Switches 2 = Two switches at full retracted / extended positions to cut current + 3rd LS to send signal
See page 7 3 = Two switches at full retracted / extended positions to send signal
4 = Two switches at full retracted / extended positions to send signal + 3rd LS to send signal
Output Signal 0 = Without 2 = Hall sensors*2

Connector 1 = DIN 6P, 90° plug 2 = Tinned leads

See page 7
Cable Length (mm) 0 = Straight, 100 1 = Straight, 500 3 = Straight, 1000

4
JP4 Ordering Key Appendix

Retracted Length (mm)

1. Calculate A+B = Y
2. Retracted length needs to ≥ Stroke + Y

A. Rear Attachment
1 +289

B. Stroke (mm)
20~150 -
151~200 -
201~250 +10
251~300 +20
301~350 +30
351~400 +40
401~450 +50
451~500 +60
501~550 +70
551~600 +80
601~650 +90
651~700 +100
701~750 +110
751~800 +120
801~850 +130
851~900 +140
901~950 +150
951~1000 +160

5
JP4 Ordering Key Appendix

Rear Attachment (mm)

1 = Aluminum casting, U clevis, slot

4.2, depth 18.0, hole 10.2
14

ø10.2
32

18
4.2

Front Attachment (mm)

1 = Aluminum CNC, no slot, hole 13.0

11.5

ø13
ø28.5

Direction of Rear Attachment (Counterclockwise)

1 = 0°

6
JP4 Ordering Key Appendix

Functions for Limit Switches

Wire Definitions
CODE Pin
1 (Green) 2 (Red) 3 (White) 4 (Black) 5 (Yellow) 6 (Blue)
1 extend (VDC+) N/A N/A N/A retract (VDC+) N/A
2 extend (VDC+) N/A middle switch pin B middle switch pin A retract (VDC+) N/A
3 extend (VDC+) common upper limit switch N/A retract (VDC+) lower limit switch
4 extend (VDC+) common upper limit switch medium limit switch retract (VDC+) lower limit switch

Connector

1 = DIN 6P, 90° plug 2 = Tinned leads

4
50

Voltage

100

Terms of Use
The user is responsible for determining the suitability of TiMOTION products for a specific application.
TiMOTION products are subject to change without prior notice.