ICU4 ICU4M Instrument Cluster

ICU4/ICU4M Instrument Cluster C01.
02
Table of Contents
System Overview
Terms and Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 501
Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 502
Warning Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503
In-Gauge Warning Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 504
Standard Warning Lights, Fixed-Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 505
Mode/Reset Switch, ICU4 Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506
"+/–" Switch, Steering Wheel, ICU4 and ICU4M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507
"My Info/Enter" Switch, ICU4M Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 508
Buzzer and Chime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509
Wake Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510
Ignition Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511
Outside Air Temperature Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
Automated Manual Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513
Diagnostic Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514
Vehicle Information, ICU4M Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516
Components
Component Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600
Component Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 601
Interface Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 602
Troubleshooting
Diagnostic Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700
ICU4/ICU4M Instrumentation Troubleshooting – Start Here . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 701
Fault Codes, ICU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 702
Gauge Diagnosis: Start Here . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703
Gauge Diagnosis: Sensor-Driven Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 704
Gauge Diagnosis: Air Pressure Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 705
Gauge Diagnosis: Fuel Level Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 706
Indicator Diagnosis: DEF Level Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 707
Indicator Diagnosis: Lamps in the ICU4/4M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 708
Indicator Diagnosis: Lamps in the Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 709
LCD Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 710
Gauge Diagnosis: Backlighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711
Mode/Reset Button Diagnosis (ICU4 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 712
Indicator Diagnosis: Seat Belt Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 713
Continued
Cascadia Troubleshooting Manual, March 2015

C01.02 ICU4/ICU4M Instrument Cluster
Table of Contents
Specifications
Roll Call Fault Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800
Fault Code Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 801
Reset EE Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 802
Sensor Resistance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 803
Cascadia Troubleshooting Manual, March 2015

ICU4/ICU4M Instrument Cluster C01.02
500 — Terms and Abbreviations

CAN—Controller Area Network
CEL—Check Engine Lamp
CGW—Central Gateway
DEF—Diesel Exhaust Fluid
FMI—Failure Mode Indicator. The part of a J1587, J1939, and CAN fault code that identifies how part of a de-
vice, or item on a device, failed.
ICU—Instrumentation Control Unit
LBCU—Lightbar Control Unit
LCD—Liquid Crystal Display
LED—Light Emitting Diode
MID—Message Identifier
MIL—Malfunction Indicator Lamp
MSF—Modular Switch Field
PID—Parameter Identifier
PWM—Pulse Width Modulation
SA—Source Address; indicates numeric assignment for a device that communicates on J1939.
SAM—Signal Detect and Actuation Module
SAM Cab—Signal Detect and Actuation Module Cab ("SAM Cabin"); this ECU controls mainly cab-related func-
tionality. See G02.04 — SAM Cab for more information.
SAM Chassis—Signal Detect and Actuation Module Chassis; this ECU controls mainly chassis-related function-
ality. See G02.05 — SAM Chassis for more information.
SFU—Switch Field Unit; see MSF.
SID—Subsystem Identifier
501 — General Information

The Ametek ICU4/4M Instrumentation Control Unit (ICU) contains up to 12 individual gauges, a lightbar control
unit (LBCU), and a daisy-chain datalink. See Fig. 1.
The LBCU drives the electrical gauges, the message center, and some of the indicator lamps. The message
center display screen on both the ICU4 and ICU4M is a liquid crystal display (LCD). The ICU4 has a one-line 7
character display. The ICU4M has a two-line 20 character display. The lightbar contains up to 24 warning and in-
dicator lights. See Table 2.
502 — Gauges
The lightbar controls all of the individual gauges ( Fig. 2), except the air pressure gauges and the optional volt-
meter, which is a stand-alone gauge. It receives data to drive the electrical gauges from sensors wired directly to
the LBCU and over the serial data bus.
Cascadia Troubleshooting Manual, March 2015 C01.02/1

A B C
1
3
4 6
5 5
5
5
07/15/2010 f545664
A. To Engine
B. To ABS
C. To Gateway
1. J1587 or J1939 Databus
2. Connections to Individual Sensors
3. LBCU
4. A-Panel Gauges
5. Cluster Datalink (jumper wires or daisy chain)
6. B-Panel Gauges
Fig. 1, ICU4/ICU4M Architecture
The LBCU uses its own proprietary databus to transmit gauge information. Each gauge has a unique address
that is known to the lightbar. Table 9 in 703 — Gauge Diagnosis identifies the input source for gauge data.
Air gauges are connected to the air supply they monitor. They are not controlled by the LBCU, except for back-
lighting.
The ICU4/4M gauges sweep 270 degrees and have pointers lit by an LED.
503 — Warning Lights

The LBCU can have up to 24 warning and indicator lights. The top row of 8 warning lamp locations are option-
ally populated. The second and third row of 16 standard warning lamps have dedicated functions.
504 — In-Gauge Warning Lights

The following four gauges have a small warning LED integrated into the gauge: coolant temperature, engine oil
pressure, transmission temperature, and fuel/DEF level.
C01.02/2 Cascadia Troubleshooting Manual, March 2015

8 8
7
40 60 100 60 100
150 200 FASTEN SEATBELTS
PSI F 0000432 MILES PSI P PSI S
0 100 100 250 0 160 0 160

OIL WATER AIR AIR
1 2 11 12
15 45 55
200 12 35 1/2
10 RPM 20 190 270
F X 100 25 50
70
90 65 F
100 8 E F 110 350

300 16 110 FUEL TRANS
OIL VOLTS 30
5 25 15 75
3 4 10
130
13 14
5 85
0 30 200 200
40 90 MPH km/h
F F
PSI F
10
100 100
0
TURBO
80 30
PYRO
150
9 10 AXLE
300
AXLE
300
5 6 15 16
12/01/2004 f610706a
1. Engine Oil Pressure Gauge 9. Tachometer

2. Engine Coolant Temperature Gauge 10. Speedometer
3. Engine Oil Temperature Gauge 11. Primary Air Pressure Gauge
4. Voltmeter 12. Secondary Air Pressure Gauge
5. Turbo Boost Air Pressure Gauge 13. Fuel level Gauge
6. Pyrometer 14. Transmission Fluid Temperature Gauge
7. Dash Message Center (lightbar faceplate) 15. Tandem Rear Axle Temperature Gauge, Forward
8. Warning and Indicator Lights 16. Tandem Rear Axle Temperature Gauge, Rear
Fig. 2, ICU4M Instrument Cluster (typical)

505 — Standard Warning Lights, Fixed-Position

EPA07 Standard Warning Lights, Fixed-Position
OPT 1 OPT 2 OPT 3 OPT 4 PUSH OPT 5 OPT 6 OPT 7 OPT 8

MODE
HOLD
RESET
ABS OPT
CHECK STOP ABS IDLE
BRAKE
09/14/2010 f610886
Opt. 1 Opt. 2 Opt. 3 Opt. 4 Opt. 5 Opt. 6 Opt. 7 Opt. 8

Stop High Exh. Tractor Trailer Cruise
CEL REGEN Opt. Idle
Engine Temp. ABS ABS Ctrl.
(yellow) (yellow) (yellow)
(red) (yellow) (yellow) (yellow) (green)
Left Turn Low Fasten High Right Turn
MIL Park Brake Low Air
Sig. Voltage Seat belt Beam Sig.
(yellow) (red) (red)
(green) (red) (red) (blue) (green)
Table 1, EPA07 Standard Warning Lights, Fixed-Position
EPA10 Standard Warning Lights, Fixed-Position
WATER WAIT CHECK

IN FUEL TO START OPT 4 OPT 5 OPT 6 TRANS OPT 8
IDLE
CHECK STOP ABS ABS
MGMT
BRAKE
BRAKE AIR
09/14/2010 f611096
Engine Water in Wait to Check

Opt. 4 Opt. 5 Opt. 6 Opt. 8
Brake Fuel Start Trans
Stop High Exh. Tractor Trailer Fasten
CEL REGEN Opt. Idle
Engine Temp. ABS ABS Seat belt
(yellow) (yellow) (yellow)
(red) (yellow) (yellow) (yellow) (red)
Left Turn Low Cruise High Right Turn
MIL Brake Brake Air
Sig. Voltage Ctrl. Beam Sig.
(yellow) (red) (red)
(green) (red) (green) (blue) (green)
Table 2, EPA10 Standard Warning Lights, Fixed-Position

506 — Mode/Reset Switch, ICU4 Only

The integral mode/reset switch is used only on the ICU4 to access the display trip screens, miles/kilometers se-
lect screens, engine screens, fault code screens, and service interval screens. The switch has two functions, (1)
mode switch (momentary push or press), and (2) reset switch (press and hold). The mode/reset switch has the
same functionality as the steering wheel +/– switch.
507 — "+/–" Switch, Steering Wheel, ICU4 and ICU4M

The steering wheel +/– is used on both the ICU4 and ICU4M to access the display trip screens, miles/kilometers
select screens, engine screens, fault code screens, and service interval screens. The switch has two functions,
(1) mode switch (momentary push or press), and (2) reset switch (press and hold). The ICU4 also has a mode/
reset switch which has the same functionality as the steering wheel +/– switch.
The steering wheel +/– switch is connected to the Modular Switch Field (MSF). The MSF transmits the switch
status to the Central Gateway (CGW). The CGW broadcasts the +/– switch status to the instrument cluster via
J1587 for the EPA07 ICU4, and via J1939 for all others.
508 — "My Info/Enter" Switch, ICU4M Only

The "My Info/Enter" switch, located in one of the MSF switch banks, provides additional menu navigation capabil-
ities on the ICU4M. The MSF transmits the switch status to the Central Gateway (CGW). The CGW broadcasts
the switch status to the instrument cluster via J1939.
509 — Buzzer and Chime

The buzzer sounds for three seconds during the self-test at start-up, and when the conditions identified in 708 —
Indicator Diagnosis: Lamps in the ICU4/4M, Table 13 exist. The buzzer will also sound if an optional circuit
connected to pin B12 is connected to ground. The chime sounds when the door is open and either:
• the parking brake is off
• the headlights are on
The chime will also sound on EPA10 vehicles with the hardwired seat belt switch option. The chime will sound
for 10 seconds if:
• the seat belt is not latched, and
• the parking brake is released.
510 — Wake Up
The LCBU will wake up to allow reading the odometer without the need to turn the ignition switch on. Wake up
mode is activated by the following actions.
• The door is opened supplying battery power to pin C4.
• The headlight switch is turned on supplying battery power to pin D16.
511 — Ignition Sequence

When the ignition key is turned to ON, the ICU4/ICU4M begins a self-test. During the first half of this process—
• all gauges controlled by the message center sweep to full scale and return;

• all display segments of the message center turn on and then turn off;
• The DEF level indicator initializes;
• the buzzer sounds for three seconds;
• the low battery voltage, low air pressure, high coolant temperature, low oil pressure, and parking brake
warning lights come on and then go off. Other lights will also initialize. See Table 13 in 708 — Indicator
Diagnosis: Lamps in the ICU4/4M for details on how all the indicators initialize at power on.
• the fasten seat belt warning light illuminates for 15 seconds. If the seat belt buckle is hardwired to the ICU,
the ICU "learns" this configuration. With a hardwired seat belt buckle switch, the fasten seat belt warning
light illuminates for 3 seconds at powerup or until the seat belt is fastened.
In the second half of the self-test, the software revision level of the ICU4M displays on the message center, fol-
lowed by the active faults, if any. When the self-test is complete, the fasten seat belt screen displays if the engine
is not running. If the engine is running, the idle hours screen displays.
512 — Outside Air Temperature Screens

Outside air temperature is displayed on the lightbar LCD screen. If miles are selected, the temperature will dis-
play in degrees Fahrenheit. If kilometers are selected, the temperature will display in degrees Celsius.
Data for the outside air temperature is received from the SAM Cab or from the engine controller. If outside air
temperature data is not received for 60 seconds, the LBCU will display three hyphens "- - -" followed by the F or
C.

When the parking brake is not set and the outside air temperature reaches 34 F (1 C) or lower, the lightbar LCD
will display a message warning of possible icy road conditions. The friendly chime will also sound for 5 seconds.
Pressing a steering wheel switch or the my info switch will reset the display to the previous screen.
513 — Automated Manual Transmission

The ICU4M can display selected gear information for vehicles with automated manual transmissions (AMT). The
last three digits at the far right on the lower line are reserved for this information. On the diagrams for the station-
ary access screens, this is indicated by the legend "AMT".
If there is a need to shift, one digit displays an arrow, either up or down depending on the shift direction. The
other two digits display the current gear.
On vehicles with conventional manual or automatic transmissions, these three digits do not display.
514 — Diagnostic Information

With the parking brake set, the Diagnostic Information menu on the ICU4/4M can display active fault codes from
the ICU and other ECUs in the vehicle. This allows instant review of fault conditions without connecting a service
tool.
Both the ICU4 and ICU4M have the ability to clear history fault codes for all ECUs on the datalink, if the vehicle
has less than 254 miles (409 km). This is to allow a body or equipment manufacturer to clear codes that may be
set while the vehicle is incomplete.
515 — Vehicle Information, ICU4M Only

Vehicle information allows you to view datalink activity in a dynamic graph format, datalink usage and error rate
(datalink status), and ICU4M data, including ICU4M serial number and software revision level.

516 — Odometer
The odometer is set to display in either miles or kilometers, depending on the primary scale of the speedometer.
The legend, either MI or KM, illuminates between the odometer and the volts display when the engine is running
or the headlights are turned on.
To toggle between MI (miles) or KM (kilometers), press the Mode/Reset button while in the SELECT screen.
The odometer is a seven-digit display with a decimal point until the vehicle has traveled 999,999.9 miles or kilo-
meters (km). At one million miles (km), the odometer rolls over to "1000000" without the decimal point, and can
continue up to 9,999,999. The odometer only displays significant figures (no leading zeros).
The ICU compares odometer data received from the engine controller to its own stored value. It will only alter its
stored value if the difference is less than 2 miles (3km). When the ICU is replaced, the odometer display will
start from zero even though the engine controller odometer may be a much larger value.
IMPORTANT: Although the odometer uses data supplied by the engine control module (ECM) to up-
date its count, it keeps its own mileage starting from zero, when it was first installed. The ICU
odometer may not match the engine ECU odometer. This may occur if the engine has been operated
with the ICU disconnected; it may also occur during factory break-in, engine service, or if the ICU has
been replaced. The odometer can be displayed with the ignition off by turning on the headlights.
600 — Component Locations
1 2 3 4 5
01/19/2007 f610863
1. ICU4 Instrument Cluster

2. Lightbar Control Unit (LBCU)
3. Mode/Reset Switch
4. Steering Wheel +/– Switch
5. Quick Info/Enter Switch (ICU4M only)
Fig. 3, Component Locations

601 — Component Details
2 3 4 2
8 7 6 5 4 3 2 1
12 34 5 6
12 34 5 6
C16 C1 A12 A1
D16 D1 B12 B1
1 1
01/05/2010 f544443a
1. 6-Pin Gauge Datalink Connector 3. 32-Pin Lightbar Connector

2. Optional Telltale Lamps 4. 24-Pin Lightbar Connector
Fig. 4, ICU4/4M Lightbar Connector Pinouts
24-Pin Lightbar Connector

Pin Circuit Number Wire Color Circuit Description
A1 29A BR (+) Panel Backlighting (Pulse Width Modulation)
EPA07 Reserved
A2 — —
EPA10 Optional Indicator #6, Ground-Activated
A3 18 R-W Low Air Pressure Indicator/Buzzer, Ground-Deactivated
A4 — — High Trans Temp Indicator (in-gauge), Ground-Activated
A5 492L GY High Exhaust Temperature, Ground-Activated
A6 — — Optional Indicator #2, Ground-Activated
A9 400 T MIL Indicator, Ground-Activated
A10 42 LTG-W (+) Forward Rear Axle Temperature Sensor
A11 42G LTG-W (–) Forward Rear Axle Temperature Sensor
A12 222A LTG High Beam Indicator, 12V-Activated
B1 — — Optional Indicator #5, Ground-Activated
B2 43 LTG-W (+) Rear Rear Axle Temperature Sensor
B3 1587– O (–) J1587 Datalink (ICU4 EPA07 Only)
B4 43G LTG-W (–) Rear Rear Axle Temperature Sensor
B5 — — Reserved
B6 — — Reserved
B7 — — Reserved


B8 — — Reserved
B9 — — Reserved
B10 1587+ DKG (+) J1587 Datalink (ICU4 EPA07 Only)
B11 376L O Tractor ABS Indicator, Ground-Activated
B12 29G LTG Optional Buzzer Input, Ground-Activated
Table 3, 24-Pin Lightbar Connector

C1 472N GY Optional Indicator #8, Idle Management Ground-Activated
C2 — — Reserved
C3 — — Reserved
C4 437W DKG Optional 12V Input, Door Open
C5 125 R-W Park Brake Indicator, Grounded-Activated
C6 — — (+) Third Axle Temperature Sensor
C7 — — Reserved
C8 38J Y Left Turn Indicator, 12V-Activated
C9 — — Reserved
C10 492J GY Regen Indicator, Ground-Activated
C11 376S O Optional Indicator #7, Ground-Activated
C12 30G LTBL-W (–) Sensor Ground (Trans Oil Temp)
C13 30 LTBL-W (+) Transmission Oil Temperature Sensor
C14 — — Optional Indicator #1, Ground-Activated
C15 440H GY Check Engine Light, Ground-Activated
C16 440A GY Stop Engine Light, Ground-Activated
D1 47 PK-W (+) Fuel Level Sensor
D2 47G PK-W (–) Fuel Level Sensor
D3 GND BK (–) Panel Backlighting
D4 — — Optional Indicator #8, 12V-Activated
D5 1939+ Y (+) J1939 Datalink (ICU4M and EPA10 ICU4)
D6 — — (-) Third Axle Temperature Sensor
D7 — — Reserved
D8 38K DKG Right Turn Indicator, 12V-Activated
D9 1939– DKG (–) J1939 Datalink (ICU4M and EPA10 ICU4)
D10 435 — Optional Seat Belt Input, EPA10 Vehicles
D11 — — Reserved


D12 376F1 O Trailer ABS Indicator, Ground-Activated
D13 GND BK-W (–) ICU Ground
D14 339 DKG (+) ICU 12V Battery Power
D15 339A DKG (+) ICU 12V Ignition Power
D16 359 LTG (+) ICU 12V Headlight Power Input (ICU Wake Up)
Table 4, 32-Pin Lightbar Connector
6-Pin Gauge Datalink Connector

1 — Blue (+) Gauge Power, Regulated 7V
2 — Green (–) Gauge Ground
3 — Black (+) Gauge Datalink
4 — Violet (–) Gauge Datalink
5 — Red (–) Gauge Backlight Ground
6 — Yellow (+) Gauge Backlight Power
Table 5, 6-Pin Gauge Datalink Connector

602 — Interface Schematic
To Panel Lamp Power (+) A1 Panel Lamps Opt. Ind. # 5 B1

A2 Opt Ind. #6 (+)Rear Rear Axle Temp B2 Axle Temp Sensor (+)
To Low Air Pressure Switches A3 Low Air Ind. J1587 (−)B3
To Automatic Transmission A4 Trans Temp Ind. (−)Rear Rear Axle Temp B4 Axle Temp Sensor (−)
To Engine A5 High Exhaust Temp Ind. Reserved B5
A6 Opt. Ind. #2 Reserved B6
A7 Opt. Ind. #3 (Wait To Start) Reserved B7 J1587 − (EPA07)
A8 Opt. Ind. #4 Reserved B8
To Engine A9 Malfunction Ind. (MIL) Reserved B9 J1587 + (EPA07)
To Axle Temp Sensor (−) A10 (+)Fwd Rear Axle Temp J1587 (+) B10
To Axle Temp Sensor (+) A11 (−)Fwd Rear Axle Temp Tractor ABS Ind. B11 To Tractor ABS
+12V To High Beam A12 High Beam Ind. Opt. Buzzer Input B12
C1 Opt. Ind. #8 (Idle Mgmt) Fuel Level (+) D1 To Fuel Level Sensor (+)
+12V Load C2 Opt. Starter Lockout Fuel Level (−)D2 To Fuel Level Sensor (−)
+12V Load C3 Opt. Ign Key Illumination Panel Lamp Gnd (−)D3
+12V C4 Door Open Opt. Ind. # 8 D4 +12V
To Park Brake SW C5 Park Brake Ind. J1939 (+) D5
C6 Third Axle Temp (+) Third Axle Temp (−)D6 J1939 CAN_H (EPA10)
C7 Reserved Reserved D7
+12V
+12V Left Turn Signal C8 Left Turn Lamp Right Turn Lamp D8 J1939 CAN_L (EPA10)
C9 Reserved J1939 (−)D9
To Engine C10 DPF Regen Ind. Seat Belt D10
C11 Opt. Ind. #7 (Check Trans) Reserved D11
To Trans Oil Temp Sensor (−) C12 Trans Temp(−) Trailer ABS Ind. D12 To Trailer ABS
To Trans Oil Temp Sensor (+) C13 Trans Temp (+) PC Board Gnd (−)D13
To Engine C14 Opt. Ind. #1 Battery Power (+) D14 +12V
To Engine C15 Check Eng Ind. Ignition Power (+) D15 +12V
To Engine C16 Stop Engine Ind. Headlamp Power (+) D16 +12V
09/14/2010 f545667
Fig. 5, Interface Schematic
700 — Diagnostic Tools Required

• ServiceLink or DiagnosticLink
• Datalink Monitor
• Digital Multimeter

701 — ICU4/ICU4M Instrumentation Troubleshooting – Start Here

ICU4 Instrumentation Troubleshooting – Start Here
Problem Type Symptom Procedure to Use
Fault Code A fault code is displayed from the ICU – SA 23 or MID 140 702
A fault code is displayed from another device on the databus 702
A roll call fault is present – Examples are "no ENG" or "no ABS" 702
"nO DATA" is displayed on the LCD 702
"nO J1939" is displayed on the LCD 702
"- - - - - - -" (seven dashes) is displayed on the LCD 702
Gauges Problem with the fuel gauge 706
Problem with the DEF level indicator 703
Problem with an air pressure gauge 705
Problem with any other databus driven gauge 703
Problem with any other sensor driven gauge 704
Backlighting Problem with backlighting in a gauge or the LCD 711
Warning Indicators Problem with an in-gauge indicator 709
Problem with an indicator in the LBCU 708
Problem with the DEF level indication 703
Problem with the seat belt indicator 713
LCD Display A segment of the LCD does not work 710
The LCD is completely inoperative 710
Mode/Reset Button The mode/reset button is sticking or does not change the display 712
+/- Steering Wheel Switch The + or – switch does not interact with the display See G02.06
My Info or Enter Button The My Info or Enter button does not interact with the display See G02.06
Table 6, ICU4 Instrumentation Troubleshooting – Start Here
702 — Fault Codes, ICU

The ICU4/ICU4M in both EPA07 and EPA10 vehicles will display fault codes that are broadcast from other devices
on the databus and fault codes generated by the LBCU itself. Use the following to determine if there is a problem
with the LBCU, another device on the databus, a sensor that is connected to a device, or with the databus.
Some internal memory errors with the LBCU will cause the LCD to display "- - - - - - -" (seven dashes). A fault
code may be active and could be read using ServiceLink or DiagnosticLink. This display indicates an electronics
failure with the ICU4/ICU4M. Replace the LBCU.
Some errors with the ambient air temperature sensor will cause the LCD to display "- - - F" (or "- - - C"). This in-
dicates an error with the data the LBCU is receiving for ambient air temperature. The temperature data is
broadcast by the SAM Cab. On EPA10 vehicles, the SAM Cab may be configured to send temperature data from
either the sensor that is located on the bumper or from temperature data received from the engine controller.
Troubleshoot the sensor using the procedure in Section G04.02, 700 — J1939 Fault Codes.

Roll call faults occur when the LBCU is not receiving data from a device that had been on the databus in the
past. If a device has been removed from the vehicle (Qualcom for example), or if the ICU had been used tem-
porarily in a different vehicle, perform the resetEE procedure. See 802 — Reset EE Procedures. When the
display shows "no ENG" or "no ABS" or any other roll call fault, troubleshoot for the cause of the device going
off-line. 800 — Roll Call Fault Messages provides troubleshooting aids for roll call faults.
The tables referenced under this heading describe fault codes that originate from the ICU4/4M message center.
Use Table 7 to diagnose all MID 140 fault codes on J1587/J1708 vehicles. Use Table 8 to diagnose all SA 23
fault codes on J1939 vehicles. When the parking brake is on, the ICU will display fault codes that originate from
other ECUs on the vehicle. Use Table 17 and Table 18 in to identify the controller broadcasting these fault mes-
sages.
ICU4/4M J1587/1708 MID 140 (ICU) Fault Codes

SID/PID FMI Description Behavior
P077 6 Forward Rear Axle Temp Sensor Short The resistance between pins A10 and A11 is less than
70
. The gauge will point full scale.
ACTION: Troubleshoot for a shorted axle temperature sensor and for a short to ground in circuit 42.
P078 6 Rear Rear Axle Temp Sensor Short The resistance between pins B2 and B4 is less than
70
P096 5 Fuel Level Circuit Open The resistance between pins D1 and D2 is greater than
298
. The gauge will point to empty.
ACTION: Use the troubleshooting procedure in 706.
P096 6 Fuel Level Circuit Short The resistance between pins D1 and D2 is less than
23.5
ACTION: Disconnect the fuel level sensor connector at the sending unit. Turn the ignition to ON and check the fault code
display. If the fault code for fuel level circuit short (FMI 6) is still active, locate and repair the short in circuit 47 between the
LBCU and the fuel level sender. Otherwise use the troubleshooting procedure in 706.
P168 1 LBCU Voltage Low The system voltage measured by the LBCU is less
than 10.5 volts.
ACTION: Troubleshoot the vehicle charging system. Test the alternator, then test for voltage drop in the alternator cables
and battery cables. If the vehicle is equipped with a remote sense circuit to the alternator, check the fuse for circuit 123E.
P177 6 Transmission Temp Sensor Short The resistance between pins C12 and C13 is less than
70
ACTION: Troubleshoot for a shorted transmission temperature sensor and for a short to ground in circuit 30.
S240 12 LBCU Internal Memory Fault The LBCU has an internal memory fault. The display
may show "- - - - - - -", (seven dashes).
ACTION: Replace the LBCU.
S254 12 LBCU Internal Electronics Fault The LBCU microprocessor or other internal critical
electronics has a fault. The display may show "- - - - - -
-", (seven dashes).
Table 7, ICU4/4M J1587/1708 MID 140 (ICU) Fault Codes

ICU4/4M J1939 SA 23 (ICU) Fault Codes

Conn/
SPN FMI Pin Description Behavior
77 6 A10 + Forward Rear Axle Temp Sensor Short The resistance between pins A10 and A11 is
A11 – less than 70
78 6 B2 + B4 Rear Rear Axle Temp Sensor Short The resistance between pins B2 and B4 is less
– than 70
96 5 D1 + D2 Fuel Level Circuit Open The resistance between pins D1 and D2 is
– greater than 298
. The gauge will point to
empty.
ACTION: Use the troubleshooting procedure in 706.
96 6 D1 + D2 Fuel Level Circuit Short The resistance between pins D1 and D2 is less
– than 23.5
ACTION: Disconnect the fuel level sensor connector at the sending unit. Turn the ignition to ON and check the fault code
display. If the fault code for fuel level circuit short (FMI 6) is still active, locate and repair the short in circuit 47 between the
LBCU and the fuel level sender. Otherwise, use the troubleshooting procedure in 706.
168 1 LBCU Voltage Low The system voltage measured by the LBCU is
less than 10.5 volts.
ACTION: Troubleshoot the vehicle charging system. Test the alternator, then test for voltage drop in the alternator cables
and battery cables. If the vehicle is equipped with a remote sense circuit to the alternator, check the fuse for circuit 123E.
177 6 C12 – Transmission Temp Sensor Short The resistance between pins C12 and C13 is
C13 + less than 70
ACTION: Troubleshoot for a shorted transmission temperature sensor and for a short to ground in circuit 30.
628 12 n/a LBCU Internal Memory Fault The display may show "- - - - - - -", (seven
dashes).
629 12 n/a LBCU Internal Electronics Fault The LBCU microprocessor or other internal
critical electronics has a fault. The display may
show "- - - - - - -", (seven dashes).
639 7 n/a Roll Call Fault Any other J1939 device that the LBCU expects
on the network but is not broadcasting will
generate a fault code. The source address will
be of the device that the LBCU is not receiving
messages from. Note that this is actually an
LBCU generated fault code.
ACTION: If a device has been removed from the vehicle, or if a used LBCU is installed, a roll call reset must be performed.
See 802 — Reset EE Procedures. If a J1939 device is not broadcasting due to an error, use the troubleshooting procedure
for that device to determine the cause of it going off-line.
Table 8, ICU4/4M J1939 SA 23 (ICU) Fault Codes
703 — Gauge Diagnosis: Start Here

Table 9 describes where the data is sourced to drive the gauges, identifies each standard and optional gauge,
and its method of control. The backlighting for all gauges is controlled by the LBCU using the intensity level data
from the MSF.

ICU4/ICU4M Gauge Input Source

Gauge Input Source on J1587/J1708 Systems Input Source on J1939 Systems
Speedometer Data from the Engine Controller PID 84 Data from the Engine Controller SPN 84
Tachometer Data from the Engine Controller PID 190 Data from the Engine Controller SPN 190
Engine Coolant Data from the Engine Controller PID 110 Data from the Engine Controller SPN 110
Temperature
Engine Oil Pressure Data from the Engine Controller PID 100 Data from the Engine Controller SPN 100
Fuel Level Sensor Connected to ICU Sensor connected to ICU
DEF Level Not Applicable Data from the Engine Controller, or the ACM,
SPN 1761
Primary Air Pressure Air Line Connected to Gauge Air Line Connected to Gauge
Secondary Air Pressure Air Line Connected to Gauge Air Line Connected to Gauge
Voltmeter Data from the Engine Controller PID 168 Data from the Engine Controller SPN 168
Engine Oil Temperature Data from the Engine Controller PID 175 Data from the Engine Controller SPN 175
Turbo Boost Pressure Data from the Engine Controller PID 439 Data from the Engine Controller SPN 1127
Transmission Manual, Eaton, and AGS - sensor connected to Manual, Eaton, and AGS - sensor connected to
Temperature ICU ICU
Allison, and G transmissions - Data from Allison, and G transmissions - Data from
transmission ECU transmission ECU SPN 177
Pyrometer Data from the Engine Controller PID 173 Data from the Engine Controller SPN 173
Forward Rear Axle Sensor Connected to ICU Sensor connected to ICU
Temperature
Rear Rear Axle Sensor Connected to ICU Sensor connected to ICU
Temperature
Application Air Pressure Air Line Connected to Gauge Air Line Connected to Gauge
Suspension Air Air Line Connected to Gauge Air Line Connected to Gauge
Pressure
Axle Lift Pressure Air Line Connected to Gauge Air Line Connected to Gauge
Table 9, ICU4/ICU4M Gauge Input Source
1. Test gauge initialization.

1.1 Turn the ignition to ON without starting the engine. All gauges except air pressure gauges should
sweep in unison to full scale and back to zero before indicating the actual value.
1.2 The DEF indicator on EPA10 vehicles will illuminate all segments then once a second turn off the
rightmost segment that is on. The last segment on the left will then turn amber, then red before the
actual DEF level is indicated
IMPORTANT: A short in the backlighting wire can cause permanent damage to the lightbar. The
short must be repaired before installing a new lightbar.
1.3 The air pressure gauges are mechanical and no initialization is possible except for them to display
the actual pressure. Do the gauges initialize as described above?
YES ! Go to step 2.

NO ! If the LBCU is completely non responsive, troubleshoot for faults with battery power on pin
D14, ignition power on pin D15, and the ground on pin D13. If there is no problem with these
circuits, replace the LBCU. If one or some of the gauges do not initialize as described above, trou-
bleshoot for a fault with the daisy chain wiring or for a defective gauge as follows. Disconnect the left
or the right gauge databus daisy chain circuits from the back of the LBCU one at a time to check if
the one that is connected begins working. If one gauge only is not working, check the daisy chain
wiring and try substituting a test gauge. A short in any of the gauges can take down all the gauges
on the daisy chain. Disconnect one gauge at a time to test. An open circuit in the daisy chain will af-
fect those gauges from that point on.
2. Is the input source of the gauge with the problem datalink driven, sensor driven, or air pressure driven?
Use Table 14 to identify the gauge input source.
FUEL LEVEL ! Go to 706 — Gauge Diagnosis: Fuel Level Gauge.
DEF LEVEL ! Go to 707 — Indicator Diagnosis: DEF Level Indicator.
SENSOR DRIVEN ! Go to 704 — Gauge Diagnosis: Sensor-Driven Gauges.
AIR PRESSURE ! Go to 705 — Gauge Diagnosis: Air Pressure Gauges.
DATALINK DRIVEN ! Continue with Step 3.
3. Confirm gauge accuracy with the applicable template or panel.
3.1 Connect ServiceLink or DiagnosticLink and open the J1587 ICU4/ICU4M Instrument Cluster tem-
plate or panel for EPA07 vehicles and the J1939 ICU4/ICU4M Instrument Cluster template or panel
for EPA10 vehicles.
3.2 Start the engine if the data is sourced from the engine.
3.3 Make sure that operating conditions will register a reading on the gauge. For example, the engine
temperature is above the minimum level on the gauge. NOTE: A test drive may be necessary if diag-
nosing the speedometer.
3.4 Monitor the affected gauge on both the ICU and on the template or panel. Do the readings closely
match?
YES! Go to test 4.
NO ! Replace the gauge.
4. Determine the problem with the data that drives the gauge.
The data that the LBCU receives from the source device is not valid. Refer to the troubleshooting instruc-
tions for the source device. For example, if the engine coolant temperature is not indicating, use the
troubleshooting material from the engine manufacturer. If the problem is with the speedometer, it may be
necessary to drive the vehicle with another vehicle pacing to note the speed, or monitor the ABS wheel
speed sensors using Meritor Toolbox. Verify the parameters are correct for axle ratio and tire size.
704 — Gauge Diagnosis: Sensor-Driven Gauges

1. If the gauge did not initialize correctly as described in 703 — Gauge Diagnosis, step 1, follow the trou-
bleshooting instructions in step 1.3.
Is the gauge reading inaccurate or completely at full scale or at zero?
INACCURATE ! Go to test 2.

FULL SCALE or ZERO !

There may also be an active fault code for the circuit which indicates a problem
with the wiring or the sensor. Use table 2 and table 3 in 601 — Component Details to identify the circuit
number and connection for the sensor. Troubleshoot the sensor and wiring for short and open circuits. Re-
pair the wiring or replace the sensor as determined.
2. Test the accuracy of the sensor using the resistance values shown in 803 — Sensor Resistance Specifi-
cations.
2.1 Measure the resistance of the sensor and compare it with the value shown in the table for the tem-
perature.
2.2 Place the sensor in a container of water with a thermometer and heat to a temperature where the
resistance can be accurately measured with an ohm meter. Does the resistance measurement
match the reading for the temperature?
NO ! Replace the sensor.
YES ! Leaving the sensor disconnected, disconnect the connectors from the ICU and measure the
resistance of the circuits to the sensor. Locate and repair a partial shorted or open circuit in the sen-
sor wiring.
705 — Gauge Diagnosis: Air Pressure Gauges

1. Identify which pressure gauge is not operating properly.
Primary or Secondary ! Go to test 2.
! Go to test 3.
Application
Suspension or Axle Lift ! Go to test 4.
2. Verify the accuracy of the primary/secondary gauges.
2.1 Drain the air tanks.
2.2 Connect an accurate pressure gauge to the primary or secondary air tank, depending on which
gauge is being diagnosed.
2.3 Start the engine and build air pressure until the compressor cuts out.
Is the air pressure gauge in the cluster within 11 psi (76 kPa) of the test gauge?
YES! The gauge is OK. No problem found.
NO ! Check the air line to the gauge for kinks and pinches. If OK, replace the air pressure gauge.
3. Verify the accuracy of the application air gauge.
3.1 Connect an accurate pressure gauge to the delivery port on the foot valve.
3.2 Make a 90 psi (621 kPa) brake application while observing the application air pressure gauge and
the test gauge.
Is the application air pressure gauge within 11 psi of the test gauge?
NO ! Check the air line to the gauge for kinks. If OK, replace the application air pressure gauge.
4. Verify the accuracy of the suspension air gauge.

Connect an accurate pressure gauge to the air suspension. Is the air suspension gauge within 11 psi (76
kPa) of the test gauge?
NO ! Check the air line to the gauge for kinks and pinches. If OK, replace the suspension air pressure
gauge.
706 — Gauge Diagnosis: Fuel Level Gauge

Inspect the connector at the fuel level sender at the fuel tank. If the connector is a three-wire type, continue with
the three-wire fuel level sender system below. If the connector has two wires, continue with the two-wire fuel
level sender troubleshooting procedure. See Fig. 6 for two-wire sender, or Fig. 7 for three-wire sender.
1
10/09/2012 f470594
1. Connector 3. Fuel Tank

2. Sender
Fig. 6, Two-Wire Sender

2
1
10/09/2012 f470593
1. Fuel Tank 3. Sender

2. Connector
Fig. 7, Three-Wire Sender
Two-Wire Fuel Level Sending Unit

The fuel level gauge is controlled by the ICU using a variable resistance input from the fuel level sending unit
that is located in the fuel tank. The fuel level sending unit resistance increases from 31±2
with a full tank to
247±3
when empty.
If the fuel level sender circuit is open or shorted to ground, there would be respectively more than 250 or less
than 29
between circuit 47 and ground. A fault will be set and the gauge will read empty until the measurement
from the sensor is between 250 and 29
.
Clogged vents or fuel lines will cause a delay on fuel tank equalizing, resulting in inaccurate fuel gauge readings.
Changes with the fuel level will not be indicated by the fuel gauge for 60 seconds. The 60-second delay applies
to activation and deactivation unless ignition power is cycled, then it will immediately indicate for the measured
value.
1. If the gauge did not initialize correctly as described in 703 — Gauge Diagnosis, step 1, replace the gauge.
2. If a 100 ohm resistor is available, disconnect the wiring harness connector at the fuel level sender and
place the resistor across circuit 47 and ground in the connector. This will simulate the fuel level sending unit
with about 1/2 tank of fuel. Turn the ignition to the ON position and observe the fuel gauge. If the gauge
points closely to the 1/2 tank mark, then the wiring and ICU are all operating correctly. Go to step 5 if there
is no problem with the wiring and ICU.
3. Check for active fault codes for fuel level circuit. Is a fuel level fault code active?

!
SHORT LOW Troubleshoot for a wiring fault in circuit 47 between the fuel level sender and the ICU. Re-
pair as appropriate.
OPEN CIRCUIT !Go to test 4.
NO !Go to test 5.
4. Determine if the problem is with the wiring or the sending unit.
4.1 Turn the ignition to OFF, then disconnect the 2-wire connector at the fuel level sender.
4.2 Use a short jumper wire to short the two circuits at the fuel level sender connector together.
4.3 Turn the ignition to ON without starting the engine. Allow the gauges to sweep then check for fault
codes. Does the ICU show an active fault for fuel level sender shorted?
!The wiring indicates continuity, go to test 5.
YES
NO!Troubleshoot and repair for an open circuit in the ground or circuit 47 between the fuel level
sender and the ICU.
5. Test the sending unit.
5.1 Turn the ignition to OFF and disconnect the batteries.
5.2 Remove the fuel sending unit from the fuel tank.
5.3 Connect an ohm meter to the pins at the fuel level sender connector. Slowly change the level of the
float arm from full to empty. See Fig. 8.
Does the resistance increase from 31±2
to 247±3
?
YES!Check the connection at the fuel level sender for corrosion. Repair any defect found.
NO !Replace the fuel level sending unit.
05/06/2010 f545654
Slowly move the float arm from full to empty.
Fig. 8, Testing the Two-Wire Fuel Level Sending

Unit
5.4 Does the fuel gauge read as expected?

YES !The fuel gauge is reading correctly.

NO !Check the mechanical integrity of the fuel sender. Is the tank rotated? Is the float arm bent or
interfering with the tank wall, return tubes or aux heater line? The fuel tank should be oriented such
that the fuel sender is at the top. Repair any defect found.
Three-Wire Fuel Level Sending Unit

The Three-wire fuel level sender receives ignition power on circuit 47E. This ignition power circuit is sourced
from either the SAM Chassis at connector X57, pin 15, or it is sourced from an under-dash splice pack. Use the
actual vehicle schematic that is found in module 847.
There are two different three-wire senders. Use Table 10 to determine the pin-out for the three-wire sending unit.
Fuel Level Sender Connections

Vendor PIN A PIN B PIN C
Parker WEBB Sending Unit Ignition Power In Signal Out Ground
SSI Sending Unit Ground Signal Out Ignition Power In
Table 10, Fuel Level Sender Connections
DASH_H_CHAS CHAS_F_H_
_F_BHB_1A DASH_BHB_1A
SSI Signal B 47 27 27 47 D1
Fuel Level Instrument
Sensor In Ground A 47G 39 39 47G D2
Cluster
Fuel Tank IGN Volt C 47E 69 69
OR
WEBB Signal B 47
Fuel Level
Sensor In Ground C 47G
Fuel Tank IGN Volt A 47E
DIM_DASH_O_
47E H IGN_SP_2A
OR
X57
47E 15
SAM
Chassis
10/10/2012 f545966
Fig. 9, Three-Wire Fuel Level Sender System Schematic

The three-wire sending unit outputs a resistance that the instrument cluster translates into fuel level. Table 11
displays the three-wire sender voltage values that can be measured with a DMM.
Approximate Voltage Values From the Three-Wire

Sender
State Approximate Voltage
Short Low Error 0.2V or less
Full Tank 0.3V
Half Tank 0.9V
Empty Tank 1.7V
Short High Error 1.8 V or more
Table 11, Approximate Voltage Values From the
Three-Wire Sender
1. Turn the ignition to ON without starting the engine. If the gauge did not initialize correctly as described in
703 — Gauge Diagnosis, step 1, replace the gauge.
2. Determine if the problem is with the wiring of the sending unit.
2.1 With the key in the ON position, backprobe and measure the voltage on all 3 circuits at the fuel level
sending unit. Use table 1 to reference the expected voltage. Record these measurements; they will
be used again later in this procedure.
2.2 Are ignition power and ground present on the expected pins?
YES! Go to test 3.
NO ! Troubleshoot for an open in circuit 47E or the ground circuit between the fuel level sender and
the voltage source. The schematic can be found in module 847.
3. Test for a wiring fault on circuit 47 between the fuel level sender and the ICU.
Connect ServiceLink or DiagnosticLink and check for fault codes from source address 23 (the instrument
cluster). Is fault code SPN 96 present?
YES ! If the fault has FMI 5, troubleshoot and repair the open circuit wiring fault on circuit 47 between the
sending unit and the instrument cluster. If the fault has FMI 6, troubleshoot and repair the short-to-ground
wiring fault on circuit 47 between the sending unit and the instrument cluster. If there is no problem with the
wiring, replace the sending unit.
NO ! Replace the sending unit.
707 — Indicator Diagnosis: DEF Level Indicator
The DEF level indicator is integrated into the fuel gauge, and uses J1939 data from the aftertreatment control
module (ACM). The DEF level is measured by a sealed non-contact variable-resistance sensing assembly located
in the DEF tank. The DEF level sensor resistance can be measured at the tank connector. For Detroit Diesel en-
gines, the level sensor signal uses pins 1 and 2. For Cummins engines, the level sensor uses pins 1 and 4.
If the vehicle has been parked for an extended period, it is possible that DEF has crystallized in the sending unit
and on the float causing it to stick. Remove the DEF tank and then the float header assembly from the DEF
tank. If the failure is a stuck float due to DEF crystallization, the float header assembly and DEF tank can be
cleaned and reinstalled. Use warm water to wash the tank, float, and sensor shaft, then use fresh DEF to refill

the tank. After cleaning, use an ohm meter to insure the resistance of the DEF level sensor changes according
to the values shown in Table 24 for Cummins engines and Table 25 for Detroit Diesel engines.
On Detroit Diesel engines, when the DEF tank is empty, the sensor will measure approximately 240
. When full,
it will measure approximately 19.8K
. On Cummins engines, when the DEF tank is empty, the sensor will mea-
sure approximately 4.8K
. When full, it will measure approximately 68
. Use the resistance to float height table
in 803 — Sensor Resistance Specifications to test the resistance for a specific float height.
When there is no DEF in the tank or when there is a fault in the DEF level sensing circuit, the indicator will flash
the red segment until the fault is corrected, or a sufficient amount of DEF is added to the tank. Perform the rec-
ommended action in Table 12 to troubleshoot faults with the DEF level sensing circuitry indicated by fault codes
with SPN 1761.
DEF Level Faults from SA 0 or SA 61

SPN FMI Description Behavior Action
1761 1 17 DEF level low The DEF level is low. MIL, CEL, The DEF tank has run too low. Fill the DEF tank so
18 31 STOP engine lamp, and engine that it is at least 25% full and idle the engine for 5
derate may be active. minutes. If the problem is still present use the DEF
level diagnostic procedure that follows.
1761 3 DEF level circuit The voltage on circuit 532F is Troubleshoot circuits 532F and 532F- between the
out of range high greater than the ACM expects. ACM and the temperature level sensor for a wiring
fault and also for an open level sensor unit.
1761 4 DEF level circuit The voltage on circuit 532F is Troubleshoot circuit 532F between the ACM and the
out of range low close to 0 volts. temperature level sensor for a wiring fault and also
for a shorted level sensor unit.
Table 12, DEF Level Faults from SA 0 or SA 61
Diagnose the DEF level indicator as follows.

1. Turn the ignition to ON but do not start the engine. Does the DEF level indicator illuminate all segments
green then turn them off beginning from the right one at a time until the left one becomes amber then red
before either showing a mid range level, or flashing the left segment red?
YES! The DEF level indication display is working properly. Go to step 2.
NO ! Replace the Fuel/DEF gauge.
2. Use Servicelink or DiagnosticLink to check for any J1939 faults. Is there a fault for SPN 1761 with FMI 3 or
4 (DEF level sensor out of range) or are any J1939 communications fault codes active? NOTE: SPN 1761
FMI 1, 17, 18, or 31 indicate the DEF level is low. For these FMIs, there is no wiring fault but there may be
a problem with DEF level indication accuracy.
YES ! If the code has FMI 4, troubleshoot for a wiring fault in circuit 532F between the DEF level sensor
and the ACM. If the code has FMI 3, go to step 3. If there is a J1939 communications fault, use the trou-
bleshooting information in this manual to locate and repair communications.
NO, or Accuracy Problem ! Go to step 4.
3. Turn the ignition to OFF then disconnect the 4 wire connector at the DEF level sender. Use a short jumper
wire to short pins 1 and 2 (for Detroit Diesel engine) or pins 1 and 4 (for Cummins engine) together in the
vehicle harness side of the connector. Turn the ignition to ON without starting the engine. Allow the indicator
initialization sequence to complete, then check for fault codes. Is there an active fault for SPN 1761 FMI 4?
YES ! The wiring indicates continuity. Go to step 4.

NO ! Troubleshoot and repair for an open in circuit 532F and/or circuit 532F- between the DEF level sen-
sor and the ACM.
4. Turn the ignition to OFF and disconnect the batteries. Remove the temperature/level sender unit from the
DEF tank. Connect an ohm meter to pins 1 and 2 (for Detroit Diesel engine) or pins 1 and 4 (for Cummins
engine) at the 4 pin connector. Slowly raise the level of the float from empty to full. Record the resistance
range measured. Does the vehicle have a Cummins or a DD engine?
Cummins !If the resistance did not vary from approximately 4.8K
at empty to 68
at the full position re-
place the temperature/level sender unit.
Detroit Diesel ! If the resistance did not vary from approximately 240
at empty to 19.68K
at the full po-
sition replace the temperature/level sender unit.
708 — Indicator Diagnosis: Lamps in the ICU4/4M

Use Table 13 to determine if an indicator lamp has a power on bulb check and how it is activated.
The ICU4 does not set fault codes for lamps that are inoperative. If an indicator does not illuminate, use Ta-
ble 13 to determine the optimal troubleshooting method.
For data-driven indicators, use ServiceLink or DiagnosticLink to monitor the data for the indicator. If the LBCU
does not illuminate an indicator when the service tool shows that it is on, there is a problem with the indicator.
The top row lamps are replaceable for the others, the LBCU must be replaced.
For indicators that are hardwired, monitor the voltage at the LBCU input pin. Use Table 13 to correlate the status
of the indicator with the voltage on the input pin. Troubleshoot the vehicle wiring harness or switch as necessary.
Indicators with a power on "bulb check" (even though they are LEDs) are confirmed to work.
Enter the vehicle’s VIN in the EZ wiring floating pin dialog box to view a list of the circuit numbers that are used
for optional indicator lamps with a "floating position". Use the position of this hardwired circuit to determine if the
signal for the lamp is active at the LBCU.
ICU4/ICU4M Warning and Indicator Lamps

Bulb Control
Lamp Symbol Check Activation Pin Buzzer Operation
Left Turn Signal None Lamp is ON when 12V is applied to the C8 "Beep" sound when
control pin. control pin is at 12V
Right Turn Signal None Lamp is ON when 12V is applied to the D8 "Beep" sound when
control pin. control pin is at 12V
High Beam None Lamp is ON when 12V is applied to the A12 None
control pin.
Brake YES Lamp is ON when ground is applied to C5 Buzzer active when

the control pin or Lamp is ON when vehicle speed is greater
BRAKE commanded over J1939 from the ABS than 2 MPH (3 km/h)
Controller. (Uses speed data from
ABS) Chime when park
brake is not set and the
door is open


Bulb Control
Brake Air YES Lamp is ON when the control pin is A3 Buzzer active whenever
Pressure open circuit. Lamp is OFF when lamp is on
ground is applied to the control pin.
Battery Voltage YES Lamp is ON when system voltage has Data Buzzer active whenever
been less than 12 volts for longer than lamp is on
40 seconds. The message is broadcast
by the engine controller.
Fasten Seat Belt YES If pin D10 is not hardwired to seat belt N/A or "Friendly" chime for 10
buckle, lamp is ON for 15 seconds at D10 seconds when pin D10 is
power-up only. If pin D10 is hardwired, hardwired if park brake is
the bulb check is three seconds long off and seat belt is not
and the lamp is OFF when ground is latched
applied to the control pin (seat belt
latched).
Check Engine YES Lamp is ON when ground is applied to C15 and None
Lamp (CEL) CHECK the control pin or Lamp is ON/ Data
FLASHING when commanded by the
engine controller.
Malfunction YES Lamp is ON when ground is applied to A9 None
Indicator Lamp the control pin.
(MIL)
Stop Engine YES Lamp is ON when ground is applied to C16 and None
STOP the control pin or Lamp is ON/ Data
engine controller.
Tractor ABS YES Lamp is ON when ground is applied to B11 and None
the control pin or Lamp is ON when Data
commanded by the tractor ABS
controller. The lamp will also be ON
when the LBCU is not receiving data
from the ABS controller.
Trailer ABS YES Lamp is ON when ground is applied to D12 and None
the control pin or Lamp is ON when Data
commanded by the trailer ABS
controller.
Cruise Control YES Lamp is ON when commanded by Data None
either the MSF (reading the steering
wheel switches) or the engine
controller. The lamp indicates that
cruise control is enabled via the on/off
switch and not that the vehicle is
driving in cruise control mode.
DPF YES Lamp is ON when ground is applied to C10 and None
Regeneration the control pin or Lamp is ON/ Data
(REGEN) FLASHING when commanded by the
engine controller.


Bulb Control
High Exhaust YES Lamp is ON when ground is applied to A5 and None
Temperature the control pin or Lamp is ON/ Data
engine controller.
Idle Management None Lamp is ON when ground is applied to C1 None
OPT the control pin.
IDLE
Low Oil Pressure YES Lamp is ON when commanded by the Data Buzzer is active when the
engine controller. The lamp will latch lamp is on
on for a minimum of 30 seconds.
High Coolant YES Lamp is ON when commanded by the Data Buzzer is active when the
Temperature engine controller. The lamp will latch lamp is on
on for a minimum of 30 seconds.
Option 1 (Engine NO* Lamp is ON when ground is applied to C14 and None
Brake) the control pin, or lamp is ON when Data
commanded by the MSF by reading the
steering wheel switches.
Option 2 (Water None Lamp is ON when ground is applied to A6 and None
In Fuel) WATER the control pin or Lamp is ON when Data
IN FUEL
commanded by the engine controller.
Option 3 YES Lamp is ON when ground is applied to A7 None

WAIT
(Wait to Start) the control pin.
TO START
Option 4 — — — A8 —
Option 5 NO Lamp is ON when ground is applied to B1 None
(Shore Power) 120V the control pin.
Option 6 — — — A2 —
Option 7 (Check YES Lamp is ON when ground is applied to C11 and None
Transmission) the control pin or Lamp is ON when Data
or f610717
commanded by the transmission
(Supplemental controller.
Restraint System) SRS
Option 8 — — — D4 —
Table 13, ICU4/ICU4M Warning and Indicator Lamps
709 — Indicator Diagnosis: Lamps in the Gauges

In-gauge lamps illuminate during power-on initialization, and when the data to the gauge indicates a fault or an
out of normal range condition. An illuminated in-gauge lamp indicates that immediate attention is necessary.

ICU4/ICU4M In Gauge Warning Lamps

Bulb
Lamp Input Source Activation
Check
Low Fuel Level YES Fuel Level Sensor When the fuel level is less than 1/8th of a tank the lamp will be ON. A
60 second delay applies to activation and deactivation unless ignition
power is cycled and it will immediately indicate for the measured value.
Low DEF Level YES Data When the DEF level is less than 15% of tank capacity, the low DEF
light will be ON. When DEF level is less than 5% of tank capacity, the
low DEF light will flash.
Low Oil Pressure YES Data Lamp is ON when the engine controller sets an active fault with FMI 01
for oil pressure.
High Coolant YES Data Lamp is ON when the engine controller sets an active fault with FMI 00
Temperature for coolant temperature.
High Transmission NO* A4 and Data Lamp is ON when ground is applied to the control pin or Lamp is ON/
Temperature FLASHING when commanded by the transmission controller or the
retarder
Table 14, ICU4/ICU4M In Gauge Warning Lamps
For data-driven lamps, use ServiceLink or DiagnosticLink to correlate the fault or fluid level condition. For the low
fuel level lamp, allow for the 60 second delay when troubleshooting.
710 — LCD Diagnosis

1. Check the LCD and the LBCU for any activity. Does the LBCU show any activity when the ignition is turned
on or is the LCD the only malfunctioning item?
LCD ONLY ! Replace the LBCU.
NO ACTIVITY FROM THE ENTIRE ICU ! Go to test 2.
2. Check the power and ground to the LBCU.
Troubleshoot for faults with battery power on pin D14, ignition power on pin D15, and the ground on pin D13.
If there is no problem with these circuits, check the daisy chain for shorts to ground and replace the LBCU.
3. Troubleshoot for the LCD illuminating with ignition off and headlamps on.
When the headlamps are on, battery voltage is sourced to the LBCU on circuit number 359 pin D16. This
voltage will turn the LCD on to display the odometer value. Does the LCD illuminate and display the odome-
ter value with ignition off and headlamps on?
YES! Feature is functioning normally.
NO ! Test for battery voltage on pin D16. This circuit is sourced from the SAM Cab on connector 10, pin
17. Repair any wiring fault that is found with this circuit between the SAM Cab and the ICU. If there is no
wiring problem, replace the LBCU.
711 — Gauge Diagnosis: Backlighting

1. Determine if the backlighting PWM circuit is operational.
1.1 Circuit 29A is sourced from the SAM Cab on connector 10, pin 13. It goes to a splice pack and one
leg of this circuit feeds the LBCU on pin A1. When the lights are on, this circuit will have some level

of voltage that is controlled by repeatedly pressing the backlighting control + and – button on the
MSF switch.
1.2 Press the backlighting control + button about 10 times. Does pin A1 at the LBCU measure about 12
volts?
YES! Go to test 2.
NO ! Troubleshoot for an open circuit or a short to ground in one of the circuit 29A legs. Disconnect
them one at a time to determine if there is a short or if the SAM Cab is not supplying the PWM sig-
nal. Check for communications faults where the SAM may not be able to receive messages from the
MSF. The problem is with backlighting power not the LBCU.
2. Check the panel lamp ground to the LBCU. Disconnect the LBCU connectors and measure for continuity on
pin D3 of the harness connector to ground. Is there continuity to ground?
YES! Go to test 3.
NO ! Repair the open ground circuit.
3. Determine if there is a problem where a gauge or one of the daisy chain circuits is shorting the backlighting
circuit, or if the problem is the LBCU.
3.1 Disconnect the LBCU daisy chain connectors from the rear of the LBCU but leave the pink 24-pin
and 32-pin connectors connected. Turn the ignition and headlights on.
3.2 Press the backlighting control + button on the MSF about 10 times, then press the – button about 10
times. Did the LCD change from full brightness after the + button had been pressed to very dim after
the – button was pressed?
YES! Go to test 4.
NO ! Replace the LBCU.
4. Determine which gauge or daisy chain circuit is open or shorted.
4.1 Reconnect one of the daisy chain circuits to the LBCU.
4.2 Turn the ignition and headlights on and press the backlighting control + button on the MSF about 10
times. Does the backlighting in the gauge chain function?
YES! Locate the short or open in the other daisy chain circuit and/or gauges.
NO ! Locate the short or open in a gauge or a daisy chain jumper in this circuit.
712 — Mode/Reset Button Diagnosis (ICU4 only)

Check the Mode/Reset button for physical binding.
1. Remove the ICU4 bezel by carefully prying it from the face of the instrument panel. For instructions, see
Section 54.04, Subject 130 of the Cascadia Workshop Manual.
2. Remove the rubber button from the LBCU. Is there debris or some other substance that may cause the but-
ton to bind and stick?
YES! Clean the substance from the button and bezel. Use care to keep all cleaning solution and debris
from entering the LBCU.
NO ! If there is an alignment problem with the LBCU and/or the bezel, determine if it can be adjusted or
repaired. If no repair is possible, replace the LBCU.

713 — Indicator Diagnosis: Seat Belt Lamp

Test the operation of the seat belt lamp.
Turn the ignition to OFF, then turn it to the ON position without starting the engine. Does the lamp always stay
on, never illuminate, or only illuminate for 3 to 15 seconds at power on?
Never ON ! The lamp itself is open circuit, replace the LBCU.
Always ON ! The ICU has learned that it is in a vehicle that has a seat belt buckle switch hardwired to LBCU
pin D10. Troubleshoot for an open seat belt buckle switch or open circuit between the seat belt buckle and the
LBCU. If the vehicle does not have a hardwired seat belt buckle switch, perform the ICU4 or ICU4M reset EE
procedure as described in Section 803 of this manual.
Only ON 3 to 15 seconds !
A vehicle that does not have a hardwired seat belt buckle switch illuminates the
lamp for 15 seconds at power-up. A vehicle that has a hardwired seat belt switch illuminates this lamp for three
seconds at power-up and then will turn it off if the seat belt input is at ground (seat belt connected). There is no
problem with the lamp circuit if it operates according to this description.
800 — Roll Call Fault Messages

The ICU4/4M expects to receive messages from the engine and ABS controller at all times. It additionally ex-
pects to continue to receive messages from any other controller that it has received messages from in the past.
If any of the controllers listed in Table 15 for J1587/1708 vehicles and Table 16 for J1939 vehicles fails to broad-
cast messages, the ICU4/4M will display a roll call fault message.
If a device was removed from the vehicle or if an ICU is installed in a vehicle that had previously been a different
vehicle, the rESEt EE procedure may be performed. The rESEt EE procedure forces the ICU to "forget" then
re-learn those devices that it expects to communicate with. See Subject 802 — Reset EE Procedures for in-
structions to perform the Reset EE procedure.
Roll call fault messages are originated by the ICU4/4M for display only. They are not broadcast over the databus
and cannot be read by a data analysis tool.
J1587/J1708 ICU4/ICU4M Roll Call Fault Messages

Displayed SID and
Description
Message FMI
no EnG SID 254 The ICU is unable to exchange data with the engine controller (CPC).
Fail 7
ECU 128 SID 254 The ICU is unable to exchange data with the engine controller (CPC).
Fail 7
no AbS SID 254 The ICU is unable to exchange data with the antilock brake controller.
Fail 7
AbS 136 SID 254 The ICU is unable to exchange data with the anti lock brake controller.
Fail 7
nO dATa — The ICU is unable to exchange data with any device in the vehicle.
130 SID 254 No data is received from the transmission controller but it had been in the past.
Fail 7
164 SID 254 No data is received from the modular switch field controller but it had been in the past.
Fail 7
181 SID 254 No data is received from the satellite controller but it had been in the past.
Fail 7

J1587/J1708 ICU4/ICU4M Roll Call Fault Messages

Displayed SID and
Description
Message FMI
190 SID 254 No data is received from the air conditioning protection unit but it had been in the past.
Fail 7
206 SID 254 No data is received from the central gateway controller but it had been in the past.
Fail 7
216 SID 254 No data is received from the SAM Chassis controller but it had been in the past.
Fail 7
219 SID 254 No data is received from the collision detection unit (VORAD) controller but it had been in the past.
Fail 7
221 SID 254 No data is received from the radio but it had been in the past.
Fail 7
223 SID 254 No data is received from the transmission shift unit but it had been in the past.
Fail 7
231 SID 254 No data is received from the cellular communications unit but it had been in the past.
Fail 7
232 SID 254 No data is received from the air bag/seat belt controller (SPACE) but it had been in the past.
Fail 7
249 SID 254 No data is received from the SAM Cab but it had been in the past.
Fail 7
Table 15, J1587/J1708 ICU4/ICU4M Roll Call Fault Messages
J1939 ICU4/ICU4M Roll Call Fault Messages

Displayed SPN and
Description
Message MI
nO J1939 SPN 639 No data is received from any device in the vehicle.
FMI 7
ENG 0 SPN 639 No data is received from the engine controller (CPC), source address 0.
FMI 7
ENG2 1 SPN 639 No data us received from the engine controller (MCM), source address 1 but it was broadcasting in
FMI 7 the past.
Trans 3 SPN 639 No data is received from the transmission controller, source address 3 but it was broadcasting in
FMI 7 the past.
TSU 5 SPN 639 No data is received from the transmission shift unit, source address 5 but it was broadcasting in
FMI 7 the past.
Brake 11 SPN 639 No data is received from the antilock brake controller, source address 11 but it was broadcasting in
FMI 7 the past.
MUX 49 SPN 639 No data is received from the modular switch field, source address 49 but it was broadcasting in the
FMI 7 past.
EEC 61 SPN 639 No data is received from the aftertreatment control module, source address 61 but it was
FMI 7 broadcasting in the past.
CEL 74 SPN 639 No data is received from the cellular communications device, source address 74 but it was

J1939 ICU4/ICU4M Roll Call Fault Messages

Displayed SPN and
Description
Message MI
SATI 75 SPN 639 No data us received from the satellite communications unit, source address 75 but it was
SRS 83 SPN 639 No data is received from the air bag/SPACE controller, source address 3 but it was broadcasting in
FMI 7 the past.
Table 16, J1939 ICU4/ICU4M Roll Call Fault Messages
801 — Fault Code Messages

Table 17 shows J1587/1708 Fault Display Messages, and Table 18 shows J1939 Fault Display Messages.
J1587/1708 Fault Display Messages

Displayed Displayed
Message System Broadcasting Fault Message System Broadcasting Fault
ECU 128 Engine Controller (CPC) CDU 219 Collision Detection Unit (VORAD)
TCU 130 Transmission Controller RAD 221 Radio
ICU 140 Instrumentation Control Unit (ICU4/ICU4M) TSU 223 Transmission Shift Controller
SFU 164 Modular Switch Field CEL 231 Cellular Phone
SAT 181 Satellite Communications (Qualcom) SBU 232 Seat Belt Unit (SPACE/Airbag System)
APU 190 Air Conditioning Protection Unit CAB 249 SAM Cab
CGU 206 Central Gateway SYS ### Where ### is the MID for a device other than
the ones listed above
Table 17, J1587/1708 Fault Display Messages
J1939 Fault Display Messages

Displayed Displayed
Message System Broadcasting Fault Message System Broadcasting Fault
ECU 0 Engine Control Unit 1 (CPC) SFU 49 Modular Switch Field
ECU 1 Engine Control Unit 2 (MCM) EEC 61 Aftertreatment Control Module (ACM)
TCU 3 Transmission Control Unit CHS 71 Sam Chassis
TSU 5 Transmission Shift Unit CEL 74 Cellular Phone
ABS 11 Antilock Brake Controller SAT 75 Satellite Communications (Qualcom)
ICU 23 Instrumentation Control Unit (ICU4/ICU4M) RAD 76 Radio
CAB 33 SAM Cab SRS 83 Safety Restraint System (SPACE/Airbag
system)
CGU 37 Central Gateway SYS ### Where ### is the source address for a device
other than the ones listed above
CDU 42 Collision Detection Unit (VORAD) — —
Table 18, J1939 Fault Display Messages

802 — Reset EE Procedures

ICU4 Reset EE Procedure
1. Apply the parking brake and turn the ignition to ON without starting the engine.
2. Press the Mode/Reset button until the SETUP message appears on the display.
3. Press and hold the Mode/Reset button until the SELECT message appears on the display.
4. Press the Mode/Reset button until the RESET EE message appears on the display.
5. Press and hold the Mode/Reset button until the word DONE is displayed.
ICU4M Reset EE Procedure

1. Apply the parking brake and turn the ignition to ON without starting the engine.
2. Press the – button on the steering wheel several times until the SETUP INFORMATION message appears
on the display.
3. Press My Info button one time.
4. Press the – button on the steering wheel several times until the display shows: PUSH ! KEY TO RESET
PARAMETERS.
5. Press the My Info button one time. The display will show "RESET PARAMETERS NO YES".
6. Press the + or – button on the steering wheel so that YES is highlighted.
7. Press the My Info button one time.
8. The ICU will now relearn all connected ECUs.
803 — Sensor Resistance Specifications

Fuel Level Sensor Resistance
Sensor Resistance (ohms)
Gauge Reading
Acceptable Range Nominal
Empty Stop 244.0 to 249.0 246.5
Empty 232.0 to 239.2 235.6
1/8 190.8 to 196.9 193.8
1/4 149.6 to 154.5 152.1
3/8 126.1 to 129.0 127.5
1/2 102.5 to 103.5 103.0
5/8 84.4 to 85.7 85.0
3/4 66.2 to 67.8 67.0
7/8 47.8 to 49.2 48.5
Full 29.4 to 30.6 30.0
Table 19, Fuel Level Sensor Resistance

Transmission Oil Temperature Sensor Resistance, Standard Gauge

Gauge Temperature (ºF) Sensor Resistance (ohms)
110 4752
150 2079
190 991
230 510
270 285
310 167
350 102
Table 20, Transmission Oil Temperature Sensor Resistance, Standard Gauge
350
310
Temp (F°)
270
230
190
150
110
0 1000 2000 3000 4000 5000
Resistance (ohms)
08/01/2005 f544444
Fig. 10, Transmission Oil Temperature Sensor

Resistance, Fahrenheit
Transmission Oil Temperature Sensor Resistance, Metric Gauge

Gauge Temperature ( C) Sensor Resistance (ohms)
60 2490
80 1255
100 680
120 390
140 234
160 145
180 95
Table 21, Transmission Oil Temperature Sensor Resistance, Metric Gauge

180
160
Temp (°C)
140
120
100
80
60
0 500 1000 1500 2000 2500
Resistance (ohms)
04/13/2004 f544445

Resistance, Celsius
Axle Oil Temperature Sensor Resistance, Standard Gauge

Gauge Temperature ( F) Sensor Resistance (ohms)
100 5933
125 3419
150 2079
175 1283
200 837
225 557
250 380
275 267
300 190
Table 22, Axle Oil Temperature Sensor Resistance, Standard Gauge
300
275
250
225
Temp (°F)
200
175
150
125
100
0 1000 2000 3000 4000 5000 6000
Resistance (ohms)
04/13/2004 f544446

Resistance, Fahrenheit

Axle Oil Temperature Sensor Resistance, Metric Gauge

Gauge Temperature ( C) Sensor Resistance (ohms)
30 8060
45 4465
60 2490
75 1503
90 915
105 595
120 390
135 267
150 185
Table 23, Axle Oil Temperature Sensor Resistance, Metric Gauge
150
135
120
Temp (°C)
105
90
75
60
45
30
0 2000 4000 6000 8000
04/13/2004 Resistance (ohms) f544450

Resistance, Celsius
Cummins DEF Level Sensor Resistance

Sensor Resistance Float Distance (mm) From
(ohms) Top Plate
68 <80
112 80
157 97.6
207 115.2
261 132.8
320 150.4
385 168
485 185.6
539 203.2
629 220.8
731 238.4

Cummins DEF Level Sensor Resistance

(ohms) Top Plate
847 256
981 273.6
1135 291.2
1316 308.8
1532 326.4
1793 344
2114 361.6
2521 379.2
3052 396.8
3744 414.4
4812 433
Table 24, Cummins DEF Level Sensor Resistance
Cummins DEF Level Sensor

500
Float Distance (mm) From Top Plate
450
400
350
300
250
200
150
100
50
0
0 1000 2000 3000 4000 5000
Resistance Ω
01/26/2011 f040818
Fig. 14, Cummins DEF Level Sensor Resistance
DDC DEF Level Sensor Resistance

(Ohms) Top Plate
19804 54
13764 74
10284 93
8074 113
6534 132
5384 152
4497 172

DDC DEF Level Sensor Resistance

(Ohms) Top Plate
3799 191
3237 211
2762 230
2375 250
2035 270
1748 289
1493 309
1272 328
1076 348
902 368
744 387
601 407
471 426
353 446
240 <446
Table 25, DDC DEF Level Sensor Resistance
Detroit Diesel DEF Level Sensor

500
Float Distance (mm) From Top Plate
450
400
350
300
250
200
150
100
50
0
0 5000 10000 15000 20000
Resistance Ω
01/26/2011 f040819
Fig. 15, DDC DEF Level Sensor Resistance

ICU4 ICU4M Instrument Cluster

Uploaded by

Copyright:

Available Formats

ICU4 ICU4M Instrument Cluster

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ICU4 ICU4M Instrument Cluster

Uploaded by

Copyright:

Available Formats

ICU4/ICU4M Instrument Cluster C01.

Cascadia Troubleshooting Manual, March 2015

Cascadia Troubleshooting Manual, March 2015

500 — Terms and Abbreviations

501 — General Information

Cascadia Troubleshooting Manual, March 2015 C01.02/1

503 — Warning Lights

504 — In-Gauge Warning Lights

C01.02/2 Cascadia Troubleshooting Manual, March 2015

0 100 100 250 0 160 0 160

100 8 E F 110 350

1. Engine Oil Pressure Gauge 9. Tachometer

Cascadia Troubleshooting Manual, March 2015 C01.02/3

505 — Standard Warning Lights, Fixed-Position

OPT 1 OPT 2 OPT 3 OPT 4 PUSH OPT 5 OPT 6 OPT 7 OPT 8

Opt. 1 Opt. 2 Opt. 3 Opt. 4 Opt. 5 Opt. 6 Opt. 7 Opt. 8

EPA10 Standard Warning Lights, Fixed-Position

WATER WAIT CHECK

Engine Water in Wait to Check

C01.02/4 Cascadia Troubleshooting Manual, March 2015

506 — Mode/Reset Switch, ICU4 Only

507 — "+/–" Switch, Steering Wheel, ICU4 and ICU4M

508 — "My Info/Enter" Switch, ICU4M Only

509 — Buzzer and Chime

511 — Ignition Sequence

Cascadia Troubleshooting Manual, March 2015 C01.02/5

512 — Outside Air Temperature Screens

513 — Automated Manual Transmission

514 — Diagnostic Information

515 — Vehicle Information, ICU4M Only

C01.02/6 Cascadia Troubleshooting Manual, March 2015

600 — Component Locations

1. ICU4 Instrument Cluster

Fig. 3, Component Locations

Cascadia Troubleshooting Manual, March 2015 C01.02/7

601 — Component Details

1. 6-Pin Gauge Datalink Connector 3. 32-Pin Lightbar Connector

Fig. 4, ICU4/4M Lightbar Connector Pinouts

24-Pin Lightbar Connector

C01.02/8 Cascadia Troubleshooting Manual, March 2015

24-Pin Lightbar Connector

32-Pin Lightbar Connector

Cascadia Troubleshooting Manual, March 2015 C01.02/9

32-Pin Lightbar Connector

6-Pin Gauge Datalink Connector

C01.02/10 Cascadia Troubleshooting Manual, March 2015

602 — Interface Schematic

To Panel Lamp Power (+) A1 Panel Lamps Opt. Ind. # 5 B1

Fig. 5, Interface Schematic

700 — Diagnostic Tools Required

Cascadia Troubleshooting Manual, March 2015 C01.02/11

701 — ICU4/ICU4M Instrumentation Troubleshooting – Start Here

702 — Fault Codes, ICU

C01.02/12 Cascadia Troubleshooting Manual, March 2015

ICU4/4M J1587/1708 MID 140 (ICU) Fault Codes

Cascadia Troubleshooting Manual, March 2015 C01.02/13

ICU4/4M J1939 SA 23 (ICU) Fault Codes

703 — Gauge Diagnosis: Start Here