GETTING TO

KNOW YOUR
DC-3 M P
O F LY
L E T
I
E
N G
-3
C D C
U R T O S
Y IDE UGLA
O
GU E DO
TH
 GEN ER A L LAY O UT A N D FEAT UR ES O F T H E D C - 3 /C- 4 7

This manual is based on and written in minor glitches that will happen if you decide to
the same style of the original document issued use an auto start/shutdown method and then
to wartime pilots of the C-47. As the DC-3 was decide to manually start/shutdown later.
the original design, the C-47 being the military The 2 options are to reset/reload the
designation, a great deal of the content applies flight after an auto start/shutdown or read the
to both aircraft. following guide.
Auto Start :

K N OW T H E D C- 3 If you start the engines using autostart

(Cntrl/E) the following items will need to then
be set manually if you later want to start/stop
Your training covers normal flight the engines manually.
procedures plus emergency procedures to get 1. Magneto switches should be set to Both.
you safely through the tight spots that come to 2. Mixture levers set to auto-rich
most pilots at one time or another. 3. Fuel tank levers will be using ALL if you use
The DC-3 has no bugs. It has been Ctrl+E. Set to any tank that actually has fuel.
around a long time doing a magnificent job. The Auto shutdown :
only troubles you will have are those you bring If you have started the engines manually
on yourself. Know your aircraft. but use auto shutdown (usually Cntrl/Shift/F1)
When you check it before flight, know you will need to reset the following items:
enough about it to spot trouble. Maintenance 1. The magneto switches. They will indicate on
personnel are human too - they make mistakes. but they aren’t actually on. Either set to off or to
Your job is to check their work before you fly. the position ready for a manual start.
Know your procedures. Confusion in the 2. The mixture levers. They will be locked in the
cockpit causes far too many accidents. Practice position that you had left them in . They will ac-
emergency procedures until they are as familiar tually be off. Either set to off or to the position
as normal operational procedures. ready for a manual start.
This simulation has ben developed with 3. Fuel tank selectors. They will be indicating
realism in mind. Therefore, just like the real the position that you had left them in. They will
thing it is VITAL that you read this instruction actually be off. Either set to off or the position
manual thoroughly to understand the correct ready for a manual start.
procedures for starting and running the engines, the
I MPORTANT!
various systems such as hydraulics and electrical and
general flying properties of your aircraft. If starting manually remember that
Autostart and Auto shutdown. the Energise and Mesh switches return to
Due to how the simulator implements their OFF position AUTOMATICALLY
Auto-start and Auto-shutdown, there are a few once and engine has started.
1 2
 1
Various combinations of doors and
2
FLY I N G T H E D C- 3 hatches are fitted, depending on the variant. The
most common variant seen today is the passen-
ger cargo version with large cargo doors fitted to 3
port in the rear of the fuselage.
The DC-3 is a 2 engine, all-metal, low- There are six emergency exits, four at the 4
wing monoplane. windows over the main wings, an escape hatch
The airplane has two 1200HP Pratt & in the cockpit roof and a removable door in the
Whitney, 14-cylinder, R-1830-90, Twin-Wasp centre of the forward cargo door (when fitted).
engines with Hamilton Standard hydromatic fully The airplane has two main sections.
feathering 3-bladed propellers. SOME aircraft In the forward section is the pilots’
are designed for higher altitude flying and have compartment, radio operator’s and navigator’s 6
5
2-speed internal “blowers” fitted. compartments and cargo space and radio racks
The hydraulic landing gear is of the con- behind the co-pilot’s bulkhead.
ventional type. Main wheels retract vertically into The rear section consists of a main cabin 7 10
11
the engine nacelles and extend approximately 11 which is divided into stations for cargo loading.
inches out of the nacelles when fully retracted. At times, long-distance fuel tanks can be fitted
In this position they are free to rotate
and are subject to normal brake action. In the
to the cabin area for long-range missions. We
do NOT include these tanks in this simulation,
8 9 THE PEDE STAL
event of a wheels-up emergency landing, the however. The Pedestal control unit is the working
aircraft can still roll and steer (depending on for- The various configurations of the air- heart of the DC-3. This is where you control the
ward speed) with minimal damage. Once stati- frame point to the versatility of the DC-3 design. engines and adjust the pitch, roll and yaw of the
nary, however, engines cannot be used to taxi or Something which has rarely been matched in aircraft as you fly. Learn it all, you will need to 12
manoeuvre. The tailwheel is non-retractable and over 70 years! know every component and where it is located.
is of the castoring type. A proficient pilot will be able to lay hands on the
exact control needed, at any stage of a flight,
Other figures of interest: without looking. 13
DIMENSIONS
Cruising Speed at 10,000 feet...................... As we stated earlier, your DC-3
WingSpan...........................................95 feet ......................approximately 185 mph TAS is fitted with a 2-stage blower
Length..............................64 feet 51/2 inches Stalling Speed...........................67mph TAS (supercharger) for each engine.
Height (at rest)...................................17 feet Service Ceiling...........................24,100 feet The controls are the yellow knobs 14
Wingloading..................25.3lbs per sq foot in the left quadrant (3).
Power Loading.......................12lbs per HP Mixture controls are
WEIGHT Seating capacity.....................28 passengers restricted to AUTO-LEAN and
Empty: AUTO_RICH with an emergency
C-47...............................................17,037 lbs Over the following pages, we explore the FULL_RICH position. The controls 15
C-47A........................................... 17,237 lbs engineering and technology employed in an are fitted with “triggers” which in the real
operational DC-3. This will serve as a cockpit aircraft are pressed to activate the levers. In this
Basic: guide and useful reference for all pilots. simulation, that is done for you. 16
C-47...............................................17,400lbs The levers are gated and will take up the
C-47A........................................... 17,700 lbs NOTE: desired position once released.
Recommended takeoff, maximum gross...
This simulation gives you the choice of aircraft CONTROL PEDESTAL 8. GyroPilot master valve
........................................................29,300lbs fitted EITHER with a “standard” Gyro-Pilot,
Restricted takeoff,maximum gross............. 9. Elevator trim adjuster
otherwise known as the “Sperry” OR with a
........................................................31,000lbs modern GNS suite of GPS and a modern Auto- 1. Throttles 10. Throttle lever friction control
Recommended landing, maximum gross... pilot. 2. Propeller controls 11. Parking Brake (Pull on)
.......................................................26,000 lbs 3. 2-stage blower controls 12. Carburettor Heat controls
You can select to fly either of these options when 4. Mixture controls 13. Carburettor heat control lock
you choose your aircraft from the Liveries section 5. Left engine tank selector 14. Right engine tank selector
of the Hangar. 6. Tailwheel lock 15. Aileron trim control
7. Rudder Trimtab control 16. Fuel tank cross-feed control
3 4
5
10 9 7 5 4 2 1 3 6 8 11 12 13 14

31 32 33

36 35
22 20 18

34 30 29 28 27 26 25 24 23 21 19 17 16 15

MAIN INSTRUMENT PANEL

1. Sperry GyroPilot Pitch and Bank 19. Cylinder Temp Gauges
2. Sperry GyroPilot Gyros 20. Hydraulic Pressure Gauge
3. Sperry GyroPilot suction 21. Four-way Fuel tank gauge selector
4. Artificial Horizon Gauge 22. Oil Temp Gauges
5. Chronometer (24hr) 23. Fuel Pressure dual gauge
6. CoPilot’s VSI 24. Oil Pressure dual gauge
7. Main Gyro Compass 25. Manifold Pressure gauge selector
8. CoPilot Airspeed Indicator 26. Tachometer dual gauge
9. Altimeter 27. Manifold Pressure dual gauge
10. Pilot Airspeed Indicator 28. GlideSlope Indicator
11. CoPilot’s Turn&Slip Gauge 29. Radio Altimeter
12. CoPilot’s Altimeter 30. Radio Compass
13. Heater Warning lights 31. Magnetic Compass
14. Landing Gear Warning lights 32. Pilot’s Turn&Slip gauge
15. Exit Open Warning light 33. Pilot’s VSI
16. Carburettor Temp Gauge 34. ADF/VOR
17. Outside Air Temp Gauge 35. Door switches
18. De-ice pressure 36. Secure aircraft switch

PLEASE NOTE: FOR A BETTER VIEW OF THE PANEL AND

WHILST FLYING, YOU CAN TOGGLE THE CONTROL COLUMN
AND YOKE OFF BY CLICKING ANYWHERE ON THE PEDESTAL.
CLICKING AGAIN WILL RESTORE THE COLUMN AND YOKE.
6
7
1 2 3 4 5 6 7 8 9 10 11

12

13
33

14
19 20 21
32 31 30 29 28 27 26 25 24 16 17 18 22 23

15
1. Quick Start Switch 18. Boost Pump switches
2. Ground Power Switch 19. Pilot Sidewall Light Switch
3. Compass light switch 20. CoPilot Sidewall Light Switch
4. Left Propeller Feathering switch 21. Rear Wall Red Spotlights Switch
5. Panel Lights switch 22. Left engine Ammeter
6. Propeller De-Icing switch 23. Right engine Ammeter
7. Cockpit lights switch 24. Engine Primer switches
8.Inverters switch 25. Pitot Heater switches
9. Carburettor De-Icing switch 26. Windshield DeIcing Pump switch
10. Right Propeller Feathering switch 27. Tail Lights Switch
11. Formation Lights switch 28. Wing Lights (Navigation) Switch
12. ADF 29. Right Landing Light switch
13. Ignition Switches 30. Left Landing Light switch
14. Altitude Limit Control 31. Passing Light switch
15. Gyro Compass DC-3 32. Master Battery switch
16. Engine Starters 33. Cold-Dark-Start Switch
17. Engine Mesh Switches

rudder.

deflection on each tab.

SY ST EM
This system consists of elevators,

of the pedestal. Scales indicate amount of

of a wheel on the left side of the pedestal.
ailerons and rudder, which are made of metal

Operate trim tabs for the ailerons and

tabs on the elevators,the right aileron and on the

rudder by means of hand cranks on the lower part

frames covered with fabric. There are all-metal trim

Operate trim tabs for the elevators by means

SU RFAC E C ON T RO L

8
 MANUAL HYDRAULIC SYSTEM
In the event of a total engine failure with To operate the system, first open the red
HYDRAULIC SYSTEM resultant loss of hydraulics or for ground opera-
tion without engines, The DC-3 has a MANUAL
wheel hydraulic pressure valve on the pump wall.
Now pump the handle up and down 6 times. As
The DC-3 has a pressure accumulator Two engine-driven pumps supply
hydraulic pressure pump. This pump will charge you do so you will see the pressure rise in the right
type hydraulic system. It operates normally, pressure for the hydraulic system. One supplies
the pressure accumulator with sufficient hydraulic hand large pressure dial on the co-pilot wall. Also,
between 675 and 925 psi. pressure for the main hydraulic system; the
pressure to operate flaps, brakes and cowl flaps, you will see the red marker fall in the sight glass to
The Hydraulic system operates the other, for the automatic pilot. You can select
along with other hydraulically driven components the lower position, indicating that fluid has flowed
landing gear, wing flaps, cowl flaps, windshield either engine pump by means of a selector valve
(such as the Sperry Gyro Pilot) whilst on the from the tank to the accumulator.
wipers, automatic pilot and brakes on all series on the control panel.
ground, with no engine power. You can now operate some of the aircraft
of the airplane. It operates the non-ram carbu- There is a hydraulic hand pump between
The hydraulic hand pump is situated systems like flaps and cowl flap controls. This is
rettor air-filter mechanism when installed and the the pilots’ seats. A valve on the hydraulic control
between the pilots’ seats. A valve on the hydraulic often necessary when the aircraft is being
blower controls when superchargers are installed. panel controls flow of pressure from the pump.
control panel controls flow of pressure from the serviced or of course, in emergencies where a loss
The control panel is in the center aisle, When you open the valve, pressure is built up in
pump to the accumulator. of hydraulic pressure is suffered.
behind the copilot’s seat. The Hydraulic Gauges the accumulator. When you close it, the accumu-
are at the right of the copilot’s seat, housed in lator is separated from the hydraulic system and
their own panel box. pressure is applied to the hydraulic lines.
This should be the FIRST
NEVER OPERATE THE SYSTEM thing you do on entering
BELOW 500PSI the cockpit.

Hydraulic Fluid Sight Gauge Hydraulic Fluid Filter Neck

Hydraulic Pump Selector Valve

HYDRAULIC FLOW SELECTOR

Hand Pump Shutoff Valve

Wing Flap Control Valve

Landing Gear Control Valve The Hydraulic Flow selector

lever allows you to select between
two settings. Pull the handle outward
Landing Gear Safety Latch Control and swing backward for TAKEOFF,
LANDING and GROUND. Swing
the lever forward to supply pressure to
Hydraulic Hand Pump the Sperry Giropilot in addition to all
9 the conventional systems.
10
 LANDING GEAR WING FLAPS

Three controls govern the operation of Your DC-3 has all-metal wing flaps.
the DC-3 landing gear. A lever on the main hy- A valve lever just above the landing gear lever
draulic control panel raises and lowers the two operates these flaps. To raise or lower the flaps,
main wheels. A tailwheel lock on the pedestal cen- first clear the slot that holds it in neutral by
ters and locks the tailwheel. The tailwheel does swinging the lever out toward the center aisle.
not retract but swivels through 360 degrees when Move the lever DOWN to lower the flaps
not locked. The third control, a safety latch, on or UP to raise them. When the flaps are in the
the floor by the pilot’s seat, controls movement desired position, return the lever to the stowed
of the safety latch and the landing gear lever. position (DISABLED) and the flaps will remain
at the set position.There is a flap position indica-
Full down (positive lock) - In this position tor to the left of the main instrument panel.
the latch is locked and can be moved only by the
latch control. The landing gear lever cannot be
FULL DOWN
moved with the latch full down.

To operate the latch, a locking tab must

first be moved from the nose of the lever.
(right click)

Full up (unlocked) - In this position the

latch is unlocked and the gear lever is free to
move. With the gear UP, pull the gear lever out
toward the center aisle. Now you can push the FULL UP
lever DOWN to lower the gear. Lock the lever
and latch the gear using the latch control.

When on the ground ALWAYS leave the
gear lever in this DOWN position.

Never move the latch to full down or positive
lock until the gear lever is in NEUTRAL
(right click)

Keep the gear and flap levers in
NEUTRAL for normal operation. This traps f
luid in the line and holds the gear and flaps in the
desired positions. (left click/hold,
release when
If the throttles are closed and the landing flaps are at the
gear is UP, a warning horn will sound. This desired position)
can be cancelled by pushing the warning horn
switch (18) on the right “eyebrow” panel.
(left click/hold)
Warning lights: There are green and red
warning lights at the right hand corner of the in-
strument panel. The green light burns when the
gear is down and the red when the gear is up.

11 12
BRAKES

SUPERCHARGERS FUEL SYSTEM
Conventional toe-operated brake pedals Early series of the DC-3 have integral sin-
on the rudder controls give independent braking gle-speed blowers with an impeller ratio of 7.15
on each wheel. (Differential Braking) to 1. For higher altitudes, later series are fitted
1. Fuel Tanks: The DC-3 has four 3. Crossfeed or Booster Pumps
Since the wheels do not retract fully with 2-speed, single stage blowers. These super-
center-section tanks, two on each side of the fuse- Some earlier DC-3s are fitted with a fuel
into the nacelles, you have braking action on the chargers have an impeller ratio of 7.15 to 1 in low
lage. Main tanks are forward; each has a capacity crossfeed system that permits either fuel pump
wheel even when retracted. Thus, when the DC-3 blower and 8.47 to 1 in high blower.
of 202 U.S. gallons. Auxiliary tanks are aft of the to supply both engines. In this simulation, the
should make a belly-landing,it can still be steered The supercharger controls are mount-
main tanks; each has a capacity of 200 U.S. gal- Cross-Feed system is inop and the lever should
by the brakes just as if the gear were extended. ed in a quadrant on the left side of the pedestal.
lons. Each tank is independent of the others. be left in the OFF position.
A parking brake control is fitted to the They have yellow knobs.
The tanks are gauged and indicated by a
lower section of the pedestal. To check for proper operation:
four-way selector gauge on the main instrument
To apply parking brakes, pull the red 1. Prop controls .................INC.RPM
panel.
knob fully out. DO NOT APPLY THE 2. Throttles...........................1700 RPM
PARKING BRAKE WHEN ALOFT. A minimum of 45 psi oil pressure is required to
operate the blower clutch. If oil pressure is low at
1700RPM, advance the throttles until oil pressure
reaches 45 psi.
3. Blower control...............HI BLOWER
4. Throttles..........................30” Hg.
5.Blower control..............LOW BLOWER
Watch the manifold pressure. A drop in manifold
pressure indicates correct clutch operation.
At low altitudes there will be little gained
by using High Blower. As the impeller is en-
gine-driven, it takes more power to drive it in
Later DC-3s and converted earlier ones
High Blower than you gain in shifting. Use High
have booster pumps fitted. The switches for these
Blower in climbing and at higher altitudes only.
are on the upper right panel. These pumps main-
tain fuel pressure if an engine pump fails. For
normal operations turn them on below 1000 feet
and above 10,000 feet.

AUTOMATIC PILOT
The automatic pilot control box consists
of a directional gyro, ball bank indicator, bank
and climb gyro, horizon bar and a suction gauge.
It is on a panel in the center of the main
2. Fuel selector valves: On each side of the pedes-
instrument panel.
tal is a fuel selector valve. The right valve controls
The automatic pilot keeps your airplane in
flow to the right engine, the left to the left engine.
straight and level flight by mechanical control of
Valves read: LEFT MAIN,RIGHT MAIN,LEFT
the rudder, ailerons and elevator. Its use is fully
AUX.,RIGHT AUX. AND OFF.
described in the section “CRUISE” later in this
Select fuel for either engine
manual.
by turning the selector valves to
the desired position.

13 14
CARBURETTOR CONTROLS OIL SYSTEM LIGHTS
There are two oil tanks, one in each na- There is a variety of exterior lighting on
celle with a capacity of 29 gallons each. the DC-3. The main groups are:
Carburettor mixtures are controlled to keep the fuel/air ratio at its most efficient level. Oil temperature and pressure gauges are
automatically for most efficient engine operation IDLE CUT-OFF - stops the flow of fuel. on the main instrument panel in front of the co- A. LANDING LIGHTS
at different altitudes. There are four mixture con- Note: AUTO RICH and AUTO LEAN are pilot, together with low pressure warning lights. B. PASSING LIGHT ( Red, incorporated
trol positions: EMERGENCY, AUTO RICH, sometimes referred to as “Takeoff and climb” Keep oil pressures between 75 and 90 psi in the left landing light housing)
AUTO LEAN and IDLE CUT-OFF. The con- and “Cruise”. in normal flight operation. Don’t let them get be- C. NAVIGATION LIGHTS
trols are to the right of the throttles on the low 60 or above 100 psi, if you are flying in emer- D. TAIL LIGHTS (Red and White)
pedestal. Carburettor heat controls: These controls gency situations. If pressures drop below 50 psi,
are located in a quadrant just below the main in- the red warning lights will glow. Some lights have dim and bright fila-
strument panel on the right side of the pedestal. ments which can be switched, others have steady
Positions: HOT and COLD. When you and flash states.
need carburettor heat to offset icing conditions, ELECTRICAL SYSTEM All switches for these lights are located
open the LOCK lever and move each control to on the left or right upper panels.
HOT. This brings heated air from the around the Two engine-driven generators supply
cylinder heads into the induction system. electric current to your airplane and charge two
Leave the controls in COLD for all nor- 88-ampere-hour batteries, housed under the
mal operations and ALWAYS LOCK them. nose of the airplane. (The battery compartments
are mounted on telescopic arms which extend
downwards to enable servicing of the batteries.)
In this simulation these are activated when the
GROUND-POWER switch is operated.
There is a master battery switch mounted
on the left upper panel. This is left OFF while
starting engines using an external power source.
Whenever possible, start engines using an
exterior battery cart (sometimes called Ground
Power Unit). This saves battery power.
You can start engines on battery power
alone. If you are going to use the starting cart,
switch up the GroundPower switch and check
C a rb u re t t o r outside to see the cart visible, connected to the
Mi x t u re C o n t ro l s batteries

To operate the controls, first press the

trigger lock fitted to each control and then move
the control to the desired position.
Here are the effects which the controls
produce at the different positions:
EMERGENCY - full rich mixture. This
position overrides any automatic function.
AUTO RICH - rich mixture
AUTO LEAN - lean mixture
An automatic feature of each carburet- Car bur ettor
tor functions in either of these positions. This Heat Controls
feature is an altitude compensator unit. As the
airplane climbs or descends, a diaphragm in this
unit measures the outside air pressure. It is very
sensitive. reacting to minute changes in pressure
and temperature. As the diaphragm expands and
contracts, it meters fuel into the induction system
15 16


RADIO SUITES
Com2), two Nav radios (Nav1 & Nav2) an ADF
receiver and finally, a Transponder.
Your DC-3 is fitted with radio sets for Immediately above the radio suite is an
communications with the ground and for AUDIO unit for audio signal and marker signal-
navigation when used in conjunction with the control.
navigation instruments.
There are two Comms radios (Com1 & The suite is mounted centrally, in the roof panel.

1. Comms1 ON/OFF and

Standby-Active switch
11
2. Comms1 Standby
Frequency (broad and fine)

3. Comms2 ON/OFF and

Standby-Active switch

4. Comms2 Standby
Frequency (coarse and fine) 1 2 3 4
5. Nav1 ON/OFF and
Standby-Active switch

6. Nav1 Standby
Frequency (broad and fine) 6 8
7. Nav2 ON/OFF and 5 7
Standby-Active switch

8. Nav2 Standby 9
Frequency (coarse and fine) This page intentionally left blank.

9. ADF 10

10. TRANSPONDER

11. AUDIO UNIT

For the

modern pilot...
The “original” DC-3 is fitted with
basic navigation equipment in the
shape of the Radio suite which pro-
vides Nav1 and Nav2 frequencies, a
Comms Radio with Com1 and Com2
and an ADF. These when coupled to the
RMI (VOR) and GSI (glideslope indica- option to use the GNS530 and 430
tor) gauges on the main panel, provide suite, together with a modern
for basic IFR navigation. The RADIO Autopilot. A knob at the base of the
COMPASS is your ADF indicator. main instrument panel, immediately
However, if you are more com- below the Manifold Pressure Gauge,
fortable with modern avionics when toggles between the Sperry Gyro-Pilot
flying in the simulator, there is an and the GNS Suite.
17 18
 RE S T RI CT E D

INSTRUMENT

Markings
DC-3
GRADE 100/130 FUEL
CYLINDER HEAD TEMPERATURE
Short Red.....................................250C FUEL PRESSURE OIL PRESSURE
Green Arc............................150-2320C Red.............................................14 PSI Red.............................................60PSI
Short Red....................................2600C Green......................................16-18PSI Green......................................75-90PSI
Red..............................................19PSI Red............................................100PSI

MANIFOLD PRESSURE OIL TEMPERATURE

Short Red line...........................48” Hg. Short Red.......................................400C
Green Arc............................43-32” Hg. Green Arc.................................60-750C DE-ICER PRESSURE AIR SPEED INDICATOR
Blue Arc...............................32-28” Hg. Short Red.....................................1000C Green..............................7.5”-8.5” Hg. Yellow...................................112 I.A.S.
Red............................................9” Hg. Red........................................255 I.A.S.

INSTRUMENT

Markings
TACHOMETER CARBURETTOR AIR TEMPERATURE HYDRAULIC PRESSURE
Short Red...............................2700rpm Yellow................................-100C +150C Green.................................675-925PSI
Green Arc......................2550-2250rpm Green.......................................15-380C
Blue Arc........................2250-1700rpm Red................................................400C Red..........................................1200PSI

19 20
N.B.: It is VITAL that you study and memorise the
following information, to ensure trouble-free starts!
STARTING g
Some pilots and operators of the DC-3 differ on t in are n
a i
the correctprocedure to start engines in a DC-3. p er STS ter BEFORE TAXIING
I
We have chosen one of the most common. In this l l o KL d la l
procedure, the final prime is Fu EC ide nua
CH ov a Crew and Passengers Aboard and Doors Secured
used to start the motor. pr is m
Fuel tank selector........to choice th Warm engines. While warming up, keep engines
below 1000 rpm until engine instruments indicate
Battery Switch............OFF (see note)
within safe operating limits. While warming engines
Note: You can start the engines using Hydraulic Pressure...
internal battery power, in which case turn the make the following checks: 675-925 PSI
battery switch ON. OR...

Battery Cart (GPU)......Attached ON Right Engine primer...

ON for 4 seconds then OFF
Fuel Booster Pumps .... ON
Right Ignition (Magneto) ...BOTH
Throttle ....... 1” open
Right Engine Starter (energise) ... ON
Propeller ..........MAX RPM
WAIT 4-5 SECONDS! Radio...
Master ignition switch...ON On and Checked
Right Engine Mesh ...........ON
Right Ignition (Magneto) ...OFF
WAIT 3 SECONDS!
Mixture control.....AUTO RICH Call the tower to see that your radio
Right Engine primer... ON is working properly and get Taxi
Clearance from Control Tower Clock...Set
As the MESH SWITCH is thrown, the propeller
will begin to turn - slowly at first and then gather-
ing speed. You should count “15 blades” at least,
before throwing the primer. This is equal to ap-
proximately 3 -4 seconds before final priming.
Once the engine is running, return the
CroundPower switch to OFF.

Battery Switch........... ON

Fuel Booster Pumps .... OFF

Whilst starting the engine, watch out for:
1. Engine Fire. See that the fire guard’s extinguish-
ers are placed properly at each side of the aircraft,
before starting. Toggle them with the “Security Altimeters...Set Gyros... Flight Controls...
Switch” (36) on the right side of the main panel.2. Set and Uncaged Free
Do not energise and mesh an engine excessively.
If the engine won’t start on your first or second
attempt, leave it and start the other engine.
3. Ensure you have enough (but not too much!)
21 throttle open. (this is required by the special start- 22
ing code used in this simulation)
 As soon as all instruments and gauges Once in position, make your checks: The DC-3 (with Pratt&Whitney engines) TRAIL POSITION; In this position, the flaps
indicate within safe operating limits, obtain taxi has cowl flaps around each engine, directly behind take up an angle dependent on airflow through
clearance from the Tower and taxi to run-up area. Parking Brake..........On the engine cowling. They control engine tempera- the cowling. The faster the airflow, the flatter the
ture by regulating air flow through the cowling. flaps will lay. Slow speeds will open the flaps to
Tailwheel...........Locked Cowl flap controls are on the right side aid engine cooling. This all happens automatically.
TAXYING of the copilot’s seat. They are marked: CLOSED,
Fuel Booster Pumps.......OFF OFF, TRAIL, OFF, OPEN. Operate by moving
Remember, the DC-3 is a large, heavy them using the serrated knob atop each control,
airplane. Although you taxi like any other 2-en- Mixtures...........Auto Rich clockwise or anti-clockwise.
gined airplane with conventional landing gear, its When set to TRAIL, the flaps will open
size and weight tend to exaggerate its movement Cowl Flaps.........OPEN and close automatically with airspeed and air
in the air and on the ground. You will soon learn pressure through the cowlings.
its characteristics but until you know the airplane Fuel Selectors.........Main Tanks IMPORTANT!
well, handle it with extreme care. For all ground operation, the controls
In straight taxiing, keep the tailwheel Propellers .............MAX RPM MUST be set to OPEN. This maximises the air
locked and use throttles as evenly as possible. passing through the engine cowlings and prevents
In cross-wind taxiing, a locked tailwheel Carburettor Heat.....COLD over-heating.
and correct use of throttles help you maintain In icy and very cold conditions, you can
direction with minimum use of brakes. When Generators...........Check Ammeters select CLOSE to assist with engine warming but OPEN POSITION; In this position the
you are taxiing cross-wind, use additional power watch the cylinder head temperature gauge for flaps are fully open and remain so until
in the upwind engine. ENGINE RUN-UP any signs of overheat and OPEN the cowl flaps another selection is made. ALWAYS use this
Anticipate your turns. Momentum gath- immediately. position when engines are running on the ground.
ered in straight taxiing is much greater than in a Advance throttles until RPM reaches
lighter airplane and carries you into turns. Before 1500. Move propeller controls to MIN RPM. This
COWL FLAPS CONTROLS
your turn, slow your airplane down and unlock operation checks governor operation and flushes CLOSED POSITION; In this position
your tailwheel. In starting or completing turns, the prop dome with warm, clean oil. the flaps are closed and lay flat against the body
use throttles in co-ordination with your brakes. of the engine cowling.
If you use throttles properly, you take a great Ignition
load off your brakes and thereby increase their
life. Increase one throttle at a time until manifold
Remember you have differential braking pressure indicates 30” Hg. Check magnetos by
in the DC-3. But do not rely entirely on it, use turning the requisite engine magneto switch from
throttle control instead. It is kinder on landing BOTH to RIGHT and back. There should be a
gear! small drop (no more than 100rpm) in revs. Imme-
diately return the control to BOTH. Do the same
Normally you make your engine run- for the other engine.
up in an area just clear of the runway. If traffic
permits and you are cleared for takeoff, you can Hydraulic Pumps
make your run-up on the runway.
The less you idle your engines between Check by using the flaps control lever and select-
run-up and takeoff the better. If there is a delay ing DOWN. If all is correct, return the flaps se-
between run-up and takeoff, keep the engines lector to the NEUTRAL position.
running at a minimum of 1000 rpm to prevent
plug fouling. At the same time, watch cylinder Check all instruments for each engine before re-
head temperatures to prevent overheating. tarding throttles.

23 24
R ES T R IC T E D Either before takeoff or before you taxi Cross-wind takeoff
for takeoff, tighten the friction control to pre- When you make a cross-wind takeoff, gain
vent throttles from slipping. sufficient speed to ensure positive rudder control
before lifting the tail. As long as you have rudder
Tailwheel.......locked control, you can co-ordinate rudder and throttles
to maintain a straight takeoff path.
Make sure your tailwheel is locked when lined up Attain enough speed to remain airborne
on runway. ff once yo have broken ground.
akeo
O R E m a l T
TAKEOFF N o rw e r S e t t i n g
Since your airplane begins to drift when

BEF E O FF Po Hg.
it becomes airborne you must crab into the wind

TAK
” to maintain straight flight. Once you have begun
Now you are ready . . . 4 6
to crab, do not allow the landing gear to touch
to advance your throttles for takeoff. Advance the ground. Damage to the gear or to the airplane
PROPELLERS
them evenly and steadily until you reach takeoff may result.
Full Forward
power. As you do so;
Max RPM
AFTER TAKEOFF (CLIMB)
Parking Brake ......release
As soon as the airplane is clear of the
The throttle movement should take a full ground, retract the gear. Hold a minimum climb
5 seconds. until you get safe single engine speed. This speed
Maintain takeoff direction by using your varies with gross weight of the airplane but is be-
rudder and if necessary, your throttles. Rud- tween 110 mph and 120 mph. IAS
der control is available directly after you reach
takeoff power. Use throttles in cross-winds or Landing Gear ........Up
to off-set swerve of the airplane. As in taxiing,
MIXTURES maintain direction in a crosswind by applying To retract landing gear
Forward to additional power to the upwind engine.
AUTO RICH In a normally loaded airplane, the tail- 1. Pilot signals............. “Gear UP”
wheel usually comes up by itself. You can assist 2. Release the safety latch from the
tail lift by slight forward pressure on the control floor catch
column. When the airplane has attained flying 3. Safety latch................Full up
GYROS... speed (85 - 90 mph under normal conditions) 4. Gear lever...................UP
Set and Uncaged you can break the ground using gentle back pres- 5. When landing gear is up and locked, re-
sure on the control column. turn the gear lever to NEUTRAL. The red warn-
ing light will burn.
Heavy load Takeoff: When you are tak-
ing off with a heavily loaded airplane, bring the To extend landing gear
tail up to a straight and level position as soon as
possible and holding the airplane on the ground, 1. Airspeed............160 mph IAS or less
allow it to attain safe airspeed according to the 2. Pilot signals............. “Gear DOWN”
load. 3. Safety latch................Full up
4. Gear lever...................DOWN
Short field Takeoff: In taking off from 5. Gear lever...................NEUTRAL
a short field, hold the airplane with brakes until 6. Green light...................ON
you have advanced the throttles from 25” to 30” 7.SafetyLatch......DOWN and LOCKED
Hg. manifold pressure. Release brakes, raise the
tail to straight and level flight position as soon as Caution
BOOSTER PUMPS....ON
possible and ease your airplane off the ground
as soon as you attain minimum flying speed. Proper sequence in operation of the latch
COWL FLAPS.......TRAIL
Do not allow the airplane to fly itself off the and gear handle is important. Any operation of
ground. the latch out of sequence results in inability to
Use flaps to shorten your takeoff run. latch gear in down position.

25 26
Remedy Cowl Flaps .......Trail or Closed SPERRY GYRO PILOT
When you are flying long distances you The airplane will be held in this flight po-
If, inadvertently you operate the latch out Cowl Flaps can have a buffeting effect if can keep your airplane in straight and level flight sition unless adjusted, using the Sperry controls.
of sequence, return to normal by the following left open. Trail position is normal or Closed if at by means of the Speery Gyro Pilot. It detects If you wish to enter a climb under Gyro-
steps: higher altitudes or operating in cold conditions. flight deviations the instant they occur and cor- pilot or if you need to adjust the pitch angle of
1. Pull the latch to the vertical position. rects them immediately and with precision. Use the nose, use the knob marked “ELEV” (8) which
2. Raise the gear handle to UP position. Mixtures ..........Auto-Lean this pilot only in ordinary weather conditions and will adjust the pitch reference (7) . The orange
3. Return the gear handle to NEUTRAL never in extremely turbulent air. horizon bar (9) will move to maintain its position
Fuel Selectors.......to Desired Tanks To set the Gyro-pilot in operation, trim in the center of the pitch reference bar and the
Wheels...Stop rotation with your airplane then: aircraft’s nose will rise (or fall). If you wish to
b
brakes
r m a l C l i m g Adjust power as required to suit alti- 1. Align the adjustable index card (2) with the maintain the pitch of the aircraft, press the Pitch
No S e t t i n tude and blower settings. gyro card (3) in the directional gyro unit. Hold knob (6) You can still ajust the pitch using
e r
Power reductions Pow Hg. 2. Check Suction (13). It should read between the ELEV (pitch reference) knob (8) If you wish
”
...42 You are now ready to trim your airplane 3.75” and 4.25” Hg. to alter your heading while under automatic pilot
Once you have attained a speed of 120 for level flight. 3. Turn the shut-off valve control on the control, turn the knob marked “RUD” to adjust
mph it is safe to make your first power reductions. hydraulic panel to the ON position. the index (upper) card in the gyro. Now TURN

Note
4. Turn the Power control (1) ON OFF the Heading Hold (5) The aircraft will turn
to ON or turn the automatic pilot control on to the new heading and the index and gyro cards
the pedestal base to ON. will align again, to show your new heading.
Maximum cylinder head temperature CRUISE POWER SETTINGS
0
may exceed 232 C. but only for takeoff and 5. Press the Heading Hold Button (5) NOTE: The servo controls (speed valves)
climb. At no time allow cylinder head tempera- At cruising altitudes reduce power to are INOP in this simulation.
0
tures to exceed 260 C. For all level flight condi- cruise conditions. For Grade91 fuel, these setting
tions, regardless of altitude or power, keep are:
0
cylinder head temperatures at or below 232 C.

5. 6. 8.

R-1830-90C ENGINES (WITH 2-STAGE BLOWER) 2. 7. 13.

3.
RPM

LOW BLOWER
M.P.
MIX. HIGH BLOWER
M.P.
MIX. MAX CYL. TEMP. 9.
min. max. min. max. min. max. 10.
1. 12.
2450 - 2550 39”- 42” Auto-Rich 34”- 36” Auto-Rich 2320C
11. 4.
2350 - 2450 36”- 39” Auto-Rich 32”- 34” Auto-Rich 2320C

2250 - 2350 32”- 36” Auto-Rich 30”- 32” Auto-Rich 2320C

Note
1. Power
2000 - 2250 28”- 32” Auto-Lean 27”- 30” Auto-Rich 2320C The Sperry Gyro Pilot is NOT
2. Index Card

3. Heading Gyro the same as the more modern
1700 - 2000 24”- 28” Auto-Lean 24”- 27” Auto-Rich 2320C
4. Index Adjuster autopilots you will be used to in flight simulators.
5. Heading Hold (push) It was designed in the late 1930’s as a device to
6. Pitch Hold (push) maintain an aircraft’s flight attitude -that is level
6. Bank indicator flight and direction, once these are set by trim-
7. Pitch Reference ming.
8. Pitch Reference Adjuster It should be remembered that this unit is
9. Pitch Indicator Bar not designed as a navigation aid and was never
10. Cage Knob meant to be one. For that, you need more modern
11. Gyro Cage (plate) equipment or do as the original pilots did - rely on
12. Attitude Wings Adjuster dead-reckoning, sextant and VFR.
13. Suction Gauge

27 28
FLIGHT CHARACTERISTICS AND LIMITATIONS
OF YOUR AIRPLANE

Your airplane has the normal flight char- Limit speed and load factors: The DC-3 is
acteristics of a 2-engine, low-wing monoplane. It designed to operate within designated limits un-
has no unusual tendencies. der various load conditions. If you exceed these
Manoeuvres: The following manoeuvres limits, you place undue strain upon the airplane
are prohibited: loops, Immelmanns, spins, dives, and structural damage or failure results.
rolls, vertical banks, inverted flight and all other
aerobatic manoeuvres. These limits are:

26,000lbs. 29,000lbs 31,000lbs

GrossWeight GrossWeight GrossWeight

Item

Max. Level Flight (IAS) 204 mph 187 mph 170 mph

Max. Glide (IAS) 255 mph 207 mph 191 mph

Max. for Extending

Landing Gear (IAS) 160 mph 160 mph 160 mph

Max. for Extending

Wing Flaps (IAS) 112 mph 112 mph 112 mph

Landing Gear......Down and latched,

Turns: Normal flight characteristics. Re- Recovery from stalls: You need between BEFORE LANDING gear handle NEUTRAL, Green light,
member the size and weight of your airplane. 500 and 1500 feet to recover from a power-off or check wheels visually.
Stalls and recovery: All stalls give warn- power-on stall. Method of recovery is normal. Automatic Pilot.......OFF
ing of their approach with light buffeting. However, avoid excessive airspeed when you are When you have turned on the downwind
Power-off stalls: Power-off stalls give recovering from a stall, to keep loss of altitude to Altimeters ..............Set leg and are opposite the runway, extend and lock
warning sooner than power-on stalls. If gear and a minimum. the landing gear. Check green light and wheels vi-
flaps are down, this warning is more apparent and Fuel Selectors.........Left to Left Main, sually. Increase propellers to 2250 rpm.
STALLING SPEEDS right to Right Main
the airplane tends to stay in level flight during the
stall. If gear and flaps are up, stalls occur with less Stalling speeds of the DC-3 vary greatly Tailwheel......Locked
warning and the airplane has a tendency to fall of under different conditions. Changes in load, pow- Mixtures.................Auto Rich
on one wing. er, flap and gear position and even slight chang- De-icers.........OFF
Power-on stalls: Power-on stalls occur es in pressure and temperature affect the stalling Before you enter the traffic pattern, set
more suddenly and with less warning than pow- speed. Your own technique also affects the stall- mixtures to AUTO RICH and change fuel selec- Parking Brake...OFF
er-off stalls. If your airplane is not in straight and ing speed. If you fly smoothly, with co-ordinat- tors to the main tanks. It is permissible to land
level flight, stalling speed is increased. In steep ed control pressures, you can fly at slower speeds on Auxiliary tanks if they are fuller than the Main Flaps.... As desired.
banks, for example, your down wing stalls and than another pilot who is rougher on the controls. tanks.
your airplane rolls. Under these conditions the The following chart of stalling speed tells With landing gear extended, reduce pow-
stalling speed of your airplane can reach values you approximately when the airplane will stall Carburettor Air.......Cold er to achieve a descent of 300-400 feet per minute
of over 100 mph. power-off. Use the chart until you are thoroughly Once on the base leg make another pow-
Stalls in turns: Stalls in turns are more familiar with your airplane. Fuel Booster pumps.......ON er reduction and maintain 120 mph until you are
sudden than stalls in straight and level flight. The straight, on the approach leg. Then make a further
down wing stalls first and drops quickly. 29 30 Propellers...............Set power reduction to approach at 85-95 mph.
LANDING

There are three types of landing: (1) A is making a straight path to the landing strip, the Increase the power slowly and go into an When you park your airplane, lock the
3-point landing, (2) Tail-low landing (tail approx- only correction needed on actual landing should approach to slow flying as the airplane approach- tailwheel, pull the parking brake ON and pull the
imately 1-2 feet above the ground when main be the angle of crab. es a tail-low attitude. Keep the airplane in this at- mixtures back to IDLE CUT-OFF to stop the en-
wheels touch) This is actually a wheel landing. (3) Use flaps at your own discretion. Less titude for as short a time as possible. You should gines. Once the engines have stopped firing, push
Wheel landing (airplane is in a level attitude when flaps should be used in stronger and more direct be slow flying, at an airspeed at or slightly above the throttles all the way forward to the stops.
main wheels touch). cross-winds. In a strong 90 degree wind, or in power-off stalling speed, just before you touch
gusty cross-winds, it is best to use no flap at all. the ground. Reduce the power completely when Fuel selectors.......OFF
1. You can make a 3-point landing in As the airplane begins to round out for you contact the ground.
a C-47 BUT this type of landing is NOT AD- landing, bring the low wing up and straighten the If you are making an actual short-field Ignition ........ OFF
VISED. Reason: Weight of the airplane causes airplane so there is no side load on the gear as it landing, use the brakes as much as necessary. For
undue stress on the airframe and gear. touches the ground. practice, however, let the airplane roll to a stop as Radios.......... OFF
2. Normally, make a tail-low landing. In a cross-wind, wheel landings are de- you would if the brakes were not functioning.
You can reduce manifold pressure to a minimum sirable as direction is easier to maintain. You can Battery Switch......OFF
during round-out in this type of landing and cut hold your airplane on the main wheels by slight Tips
the engines after making contact with the ground forward pressure on the controls. Don’t undershoot and slow fly long dis- Landing Gear Handle .....DOWN
- or you can cut power before round-out and Once on the ground, maintain directional tance to reach the field. This leaves you helpless
land without power. As speed is dissipated, the control by use of rudder, power on the upwind if an engine fails. Flap handle .....UP
tail lowers and contacts the ground by itself. You engine and by use of brakes. Don’t’ use excessive speed early in the ap-
can aid this by slight back-pressure on the control Remember, you have not finished flying proach. This prevents a low roundout before you (FOR THIS SIMULATION)
column providing your roll speed is slow. your airplane until you have come to a complete reach the field.
3. Although a tail-low landing is desir- stop, especially in a cross-wind. Don’t drop below a safe airspeed early in Security Switch .......ON
able under normal conditions, you can make the approach.
a wheel landing with the DC-3. In this type of CROSSWIND LANDINGS Don’t use excessive power in the last of This will leave your airplane with
landing, hold roundout to a minimum and allow the roundout. This causes the airplane to balloon chocks set, battery boxes lowered
the airplane to settle on the main wheels from a Tactical operation of the C-47, especial- and destroys the value of the procedure. and extinguishers deployed.
level-flight position. Contact the ground approx- ly in combat theatres, often requires you to make
NO-FLAP LANDING
imately 10 - 15 mph faster than with a tail-low short-field landings. Field conditions and ap-
landing and hold the main wheels on the ground proach clearances vary in different parts of the Make your approach to a non-flap landing
with slight forward pressure of the control col- world. Landing fields may be small where little lower and with speed slightly higher than in an
umn. As speed decreases, neutralise pressure on landing space remains. ordinary approach. As you normally approach in
the control column or use gentle back pressure to Runways and fields may be rough mak- a tail-low attitude it is better to make a tail-low
allow the tail to lower to the ground. ing fast wheel landings dangerous or they may be landing than a wheel landing.
ice-covered making brakes useless. The following
CROSSWIND LANDINGS landing techniques, however, are designed to get During the landing roll, pull your flaps up,
you down safely under all these conditions. open the cowl flaps, turn off the booster pumps,
There are three possible ways to land place elevator trim in neutral and put the propel-
cross-wind: (1) Hold the airplane straight and Technique lers in high rpm.
level toward the landing strip and drop one wing Set the base leg to establish a normal pow- Rudder control is available for the major
into the wind, just enough to counteract drift. er approach. Set the glide to undershoot slightly. part of the roll. Use your rudder rather than the
(2) Head airplane into the wind enough to keep This is the key to a good short-field landing. brakes to maintain direction. At the end of the
straight (crabbing). (3) Combination of both. Hold a normal approach speed from the roll, apply brakes evenly.
The best method is the third: Head into top of the approach to the start of the roundout.
PARKING
the wind and lower the upwind wing. This meth- Make the roundout in the shortest possible for-
od keeps the bank and crab to a minimum and ward distance. Parking brake.......ON
makes it easier to straighten the airplane when Make corrections early on the approach,
close to the ground. Crab just enough to avoid if you are undershooting too much. Use power Cowl Flaps............ as desired
slipping. Any unco-ordinated movement may to clear obstructions - don’t depend on judge-
raise the stalling speed of the airplane. ment alone from high on the approach. Correct Mixtures................Idle Cut-off
In cross-wind landings, correct for drift as by varying power and angle of glide to maintain a
soon as possible on the approach. If the airplane constant airspeed.
31 32
 R ES T R IC T E D AFTER LANDING
Checklists NOTE: These checklists are for simulation purposes
ONLY. In no way are they intended for real-world
aviation use.

Parking Brake.........ON
WEIGHT AND BALANCE
Tailwheel.................Locked
It is important to make sure that the con-
figuration of the airplane selected, matches the Carburettor Air........Cold
fuel/payload data listed in the simulator drop-
down menu. The simulation will react to any Fuel Selector Valves....Left to Left
changes in the data that you make or enter. Main; Right to
Once you have established your intended Right Main
COWL FLAPS.......OPEN FLAPS.... FUEL BOOSTER PUMPS... flight and have fuel and payload data available,
UP OFF enter these values in the boxes provided. Adjust Propellers......Full Forward High RPM
the payload fore and aft to achieve a good CoG
balance as indicated on the plane graphic of the Throttles................Cracked (5-10%)
drop-down. Doing this will decrease the amount
of time required to trim the aircraft for level and Mixtures................Full Rich
balanced flight.
K THE
C
LO EEL Pitot Heaters..........OFF
UN
WH END BEFORE STARTING ENGINES
TAIL R THE OLL
Inverter..................ON
NEA OUR R STARTING ENGINES
Y
PROPELLERS OF Hydraulic Pump
Full Forward selector....................LEFT ENGINE
Max RPM Fuel Booster pumps.......ON
ELEVATOR TRIM TAB....
NEUTRAL Gear Latch.............Down and Locked
Right Engine Primer.......ON (5 secs)
Flap Handle..........Flaps UP and then then OFF

OL
The DC-3 is equipped with an engine fire control system. A system of to Neutral
valves and pipework enable the system to be operated conveniently from
T R the pilots’ seats. A red panel in the floor is lifted to reveal the engine Master Ignition Switch.....ON

O N selector and fire extinguisher handle. Hinged to the lid of the fire panel is Gear Handle..........Neutral

E C another compartment containing shut-off valves for fuel and oil. Right Engine Magneto........BOTH

FIR
Battery Switch........OFF
Right Starter (energiser)... ON (wait)
Open lid with handle Battery cart (GPU)......ON
Right Engine Mesh...ON (wait)
Fuel Gauges...........Check ALL
Right Engine Primer.......ON (after 15
Cowl Flaps.............OPEN blades)

De-icers..................OFF Battery Switch........ON

Automatic Pilot.......OFF Ground Power Switch ....OFF

Select affected engine Open rear lid
Lights......................As required REPEAT PROCEDURE FOR LEFT
ENGINE
Flight Controls ........FREE

Crossfeed................OFF

Pull extinguisher handle Turn cut-off valves OFF Trim Tabs.................Neutral

33 34

BEFORE TAXIING Fuel Booster pumps.......ON Landing Gear......Down and latched,
gear handle NEUTRAL, Green light,
Tailwheel.................Locked (when check wheels visually.
Hydraulic Pressure....675-925 psi lined up with runway)
Tailwheel.................Locked
Radios............. ON and tuned
AFTER TAKEOFF De-icers..................OFF
Altimeters...............Set
Landing Gear..........UP Parking Brake .......OFF
Clock......................Set
Wheels......Stop rotation with brakes Flaps...................as desired
Gyros....................Set and un-caged
Power reductions.....as advised AFTER LANDING
Flight Controls........Free
Fuel Booster Pumps......OFF
Parking Brake .......OFF Flaps...................UP

Tailwheel................Unlocked CRUISE Cowl Flaps.............Open

TAXI TO RUN-UP AREA. Fuel Booster Pumps......OFF

Cowl Flaps.............As required
ENGINE RUN-UP Elevator Trim.........Neutral
Mixtures................Auto Lean
Propellers.....Full Forward high RPM
Parking Brake.........ON Fuel Selector Valves....Cruise tanks
Tailwheel.................Unlocked
Tailwheel.................Locked Power adjustments.....as advised
PARKING
Fuel Booster Pumps......OFF Automatic Pilot........as required

Mixtures............Auto Rich Parking Brake.........ON

BEFORE LANDING
Cowl Flaps.............OPEN Cowl Flaps.............as desired
Automatic Pilot........OFF
Fuel Selectors..........Main Tanks Tailwheel.................Locked
Altimeters...............Set
Propellers.......Through Full Range Mixtures............Idle cut-off
Fuel Selector Valves....Left to Left
Magnetos.........Check Main; Right to Fuel Selectors..........OFF
Right Main
BEFORE TAKEOFF Ignition...........OFF
Mixtures............Auto Rich
Radios.............OFF
Mixtures............Auto Rich Carburettor Air........Cold
Battery Switch.....OFF
Cowl Flaps.............TRAIL Fuel Booster Pumps......ON
Landing Gear Handle.......Down
Propellers.......... Inc. RPM Ignition...........Check
Flap Handle........UP
Gyros....................Set and un-caged Propellers...............Set

35 36
 TA RT A R K
T O-S If you are going to use ctrl/E to start the engines
L D -D
A U (auto-start), PLEASE READ THE FOLLOWING:
C O
Using the keystroke combination ctrl/E will OVER-
RIDE most of the specially written programming
code in the C47/DC-3. A special switch marked “CD” on the left eye-
brow panel (33) will toggle a Cold-Dark state for the
The following specific items will not function cockpit. This automatically sets all switches and controls
correctly: to their default OFF positions and the cockpit is now
ready for a full manual start OR:
1) Mixture levers. These are “gated” and pro-
grammed to simulate Auto-Lean and Auto-Rich
states. The programming code behid them will not
TA RT
S
function with ctrl/E and they are not designed to
work with standard keystrokes for mixtures.
I C K
You will have default mixture settings ONLY. Q U
2) Magneto switches. These are by-passed when
ctrl/E is used and will not function. They have been
specially programmed to replicate the start procedure A special switch marked “QS” on the left eye-
in a real DC3/C-47. They will NOT function under brow panel (1) will toggle on a Quick-Start” state for the
ctrl/E. cokpit. This automatically sets everything to the states
necessary to carry out a manual start. So things like ig-
3) Fuel tank selectors. These are by-passed nition, magnetos etc. are already ON ready for you to
completely by ctrl/E which simply defaults to an commence energizing the engines.
“ALL” tank selection state. Visually, the tanks selec-
tors will remain “OFF” even though fuel if flowing.

If you have used ctrl/E to start and are considering

saving the flight, you MUST return all levers, switches
and controls to their default state before saving. You
can do this in two ways:

1) Return everything manually

2) Use the “Cold/Dark” switch on the OPTIONS

panel

If you do not do this, when you reload, you will not

have full function in your cockpit.

T O - N
AU TDOW Similarly, if you plan to “auto-shutdown” this will

SHU
also override any specially coded functions. If you
save a flight after auto-shut-down (ctrl/shift/F1)
again, nothing will function properly when you load
up again. To have the aircraft load properly again, you
MUST return everything to its default state.

37 38