Awwa C600-99

American Water Works Association
ANSI/AWWA C600-99
(Revision of ANSI/AWWA C600-93)
AWWA STANDARD
FOR
INSTALLATION OF DUCTILE-IRON WATER
MAINS AND THEIR APPURTENANCES
Effective date: January 1, 2000.

First edition approved by AWWA Board of Directors May 8, 1977.
This edition approved June 20, 1999.
Approved by American National Standards Institute Oct. 20, 1999.
AMERICAN WATER WORKS ASSOCIATION

6666 West Quincy Avenue, Denver, Colorado 80235
Copyright © 1999 American Water Works Association, All Rights Reserved

AWWA Standard
This document is an American Water Works Association (AWWA) standard. It is not a specification.
AWWA standards describe minimum requirements and do not contain all of the engineering and
administrative information normally contained in specifications. The AWWA standards usually
contain options that must be evaluated by the user of the standard. Until each optional feature is
specified by the user, the product or service is not fully defined. AWWA publication of a standard
does not constitute endorsement of any product or product type, nor does AWWA test, certify, or
approve any product. The use of AWWA standards is entirely voluntary. AWWA standards are
intended to represent a consensus of the water supply industry that the product described will
provide satisfactory service. When AWWA revises or withdraws this standard, an official notice of
action will be placed on the first page of the classified advertising section of Journal AWWA. The
action becomes effective on the first day of the month following the month of Journal AWWA
publication of the official notice.
American National Standard

An American National Standard implies a consensus of those substantially concerned with its scope
and provisions. An American National Standard is intended as a guide to aid the manufacturer, the
consumer, and the general public. The existence of an American National Standard does not in any
respect preclude anyone, whether that person has approved the standard or not, from manufactur-
ing, marketing, purchasing, or using products, processes, or procedures not conforming to the
standard. American National Standards are subject to periodic review, and users are cautioned to
obtain the latest editions. Producers of goods made in conformity with an American National
Standard are encouraged to state on their own responsibility in advertising and promotional
materials or on tags or labels that the goods are produced in conformity with particular American
National Standards.
CAUTION NOTICE: The American National Standards Institute (ANSI) approval date on the front
cover of this standard indicates completion of the ANSI approval process. This American National
Standard may be revised or withdrawn at any time. ANSI procedures require that action be taken
to reaffirm, revise, or withdraw this standard no later than five years from the date of publication.
Purchasers of American National Standards may receive current information on all standards by
calling or writing the American National Standards Institute, 11 W. 42nd St., New York, NY 10036;
(212) 642-4900.
All rights reserved. No part of this publication may be reproduced or transmitted in any form or by
any means, electronic or mechanical, including photocopy, recording, or any information or retrieval
system, except in the form of brief excerpts or quotations for review purposes, without the written
permission of the publisher.
Copyright © 1999 by American Water Works Association

Printed in USA
ii

Committee Personnel
The AWWA A21 Subcommittee on the Installation of Ductile-Iron Pipe, which
developed and reviewed this standard, had the following personnel at the time:
Charles W. McCauley Jr., Chair
Consumer Members
J.L. Doane, Portland Water Bureau, Portland, Ore. (AWWA)

D.S. Mathon, St. Louis County Water Company, St. Louis, Mo. (AWWA)
R.Y. Matsui, Board of Water Supply, Honolulu, Hawaii (AWWA)
General Interest Members
Harold Kennedy Jr., Suiken and Kennedy LLP, Morrisville, N.C. (AWWA)
W.H. Smith, W.H. Smith & Associates, Flora, Ill. (AWWA)
J.M. Vellano, Vellano Brothers Inc., Latham, N.Y. (AWWA)
Producer Members
J.C. Delk, McWane Cast Iron Pipe Company, Birmingham, Ala. (AWWA)
L.R. Dunn, U.S. Pipe and Foundry Company, Birmingham, Ala. (AWWA)
C.W. McCauley Jr., Griffin Pipe Products Company, Lynchburg, Va. (AWWA)
P.A. Selig, American Cast Iron Pipe Company, Birmingham, Ala. (AWWA)
T.F. Stroud, Ductile Iron Pipe Research Association, Birmingham, Ala. (AWWA)
The AWWA Standards Committee Ductile-Iron Pipe and Fittings, which reviewed
and approved this standard, had the following personnel at the time of approval:
Edward T. Knudsen Jr., Chair

Philip A. Selig, Vice-Chair
Consumer Members
T.E. Coughran, City of Santa Ana, Santa Ana, Calif. (AWWA)

A.J. DeBoy, Indiana–American Water Company, Greenwood, Ind. (AWWA)
R.R. Goold, Johnson County Water District #1, Kansas City, Kan. (AWWA)
E.T. Knudsen Jr., St. Petersburg, Fla. (AWWA)
J.D. Larson, St. Louis County Water Company, St. Louis, Mo. (AWWA)
G.L. Meyer, City of Sioux Falls, Sioux Falls, S.D. (AWWA)
T.C. Moreno, Bexar Metropolitan Water District, San Antonio, Texas (AWWA)
C.R. Schwenker, Fairfax County Water Authority, Merrifield, Va. (AWWA)
R.D. Zwygart, Tampa Water Department, Tampa, Fla. (AWWA)
General Interest Members
K.M. Bell, Underwriters Laboratories Inc., Northbrook, Ill. (UL)

Vance Forsgren, Forsgren Associates, Rexburg, Idaho (AWWA)
iii

Joseph Goss,* Delon, Hampton & Associates, Rockville, Md. (AWWA)
K.W. Henderson, Malcolm Pirnie Inc., White Plains, N.Y. (AWWA)
M.G. Hoover, HYA, a Dames & Moore Company, Pasadena, Calif. (AWWA)
M.B. Horsley, Black & Veatch Engineers LLP, Overland Park, Kan. (AWWA)
W.B. Jeffcoat, CH2M Hill, Montgomery, Ala. (AWWA)
Harold Kennedy Jr., Suiken and Kennedy LLP, Morrisville, N.C. (AWWA)
J.L. Lane,† Council Liaison, Missouri Department of Natural Resources,
Jefferson City, Mo. (AWWA)
E.W. Misichko,* Underwriters Laboratories, Northbrook, Ill. (UL)
R.L. Scarpa, Metcalf and Eddy Inc., Austin, Texas (NEWWA)
W.H. Smith, W.H. Smith & Associates, Flora, Ill. (AWWA)
J.H. Wilber,† Standards Engineer Liaison, AWWA, Denver, Colo. (AWWA)
L.C. Yates, McGoodwin Williams and Yates, Fayetteville, Ark. (AWWA)
Producer Members
L.R. Dunn, US Pipe & Foundry Company, Birmingham, Ala. (DIPRA)

B.C. Helton,* American Cast Iron Pipe Company, Birmingham, Ala. (DIPRA)
C.M. Luna, McWane Cast Iron Pipe Company, Birmingham, Ala. (DIPRA)
C.W. McCauley Jr., Griffin Pipe Products Company, Lynchburg, Va. (AWWA)
P.L. Robertson, Specification Rubber Products, Alabaster, Ala. (AWWA)
P.A. Selig, American Cast Iron Pipe Company, Birmingham, Ala. (DIPRA)
Dennis Shumard, EBAA Iron Inc., Eastland, Texas (AWWA)
T.F. Stroud, Ductile Iron Pipe Research Association, Birmingham, Ala. (DIPRA)
* Alternate
† Liaison, nonvoting
iv

Contents
All AWWA standards follow the general format indicated subsequently. Some variations from this format may be
found in a particular standard.
SEC. PAGE SEC. PAGE
Foreword 5 Verification
I Introduction........................................ vii 5.1 Inspection ............................................ 20
I.A Background......................................... vii 5.2 Hydrostatic Testing ............................ 21
I.B History ................................................ vii 6 Delivery ............................................. 25
I.C Acceptance .......................................... vii
II Special Issues .................................... viii Figures
III Use of This Standard........................... ix
III.A Purchaser Options and 1 Laying Conditions for Ductile-
Alternatives....................................... ix Iron Pipe ............................................. 8
III.B Modification to Standard..................... ix 2 Push-on-Joint Assembly........................ 9
IV Major Revisions.................................... ix 3 Mechanical-Joint Assembly ................ 10
V Comments............................................. ix 4 Pipeline Curve Geometry .................... 11
5 Preferred Method for Making
Standard Direct Service Taps on
Polyethylene-Encased Iron
1 General Pipe.................................................... 19
1.1 Scope ...................................................... 1
1.2 Purpose .................................................. 1 Tables
1.3 Application............................................. 2
1 Suggested Trench Widths at the
2 References ........................................... 2 Top of the Pipe ................................... 5
2 Mechanical-Joint Bolt Torque............. 11
3 Definitions........................................... 3
3 Maximum Joint Deflection Full-
4 Requirements Length Pipe—Push-on-Type
4.1 Permeation ............................................ 3 Joint Pipe .......................................... 12
4.2 Installing Ductile-Iron Mains .............. 4 4 Maximum Joint Deflection Full-
4.3 Disinfection.......................................... 16 Length Pipe—Mechanical-Joint
4.4 Highway and Railroad Pipe.................................................... 13
Crossings .......................................... 17 5 Maximum Stacking Heights—
4.5 Subaqueous Crossings ........................ 17 Ductile-Iron Pipe ............................. 20
4.6 Service Taps ........................................ 18 6A Hydrostatic Testing Allowance per
4.7 Unloading, Handling, and 1,000 ft of Pipeline—gph ................ 23
Storage.............................................. 18 6B Hydrostatic Testing Allowance
per 300 m of Pipeline—L/h ............ 24

This page intentionally blank.

Foreword
This foreword is for information only and is not a part of AWWA C600.
I. Introduction.
I.A. Background. The provisions of this standard were intended to act as a
guide for installing extensions to existing distribution systems and in preparing
specifications for contracts for the construction of new systems or extensions. The
standard was to be used as a guide for installing bell-and-spigot cast-iron pipe and
did not cover the provision and delivery of material, any other type of pipe, or any
other type of joint. The standard included a model addendum, which was to be used
with project specifications, and was designed to be used as a part of the contract
documents.
I.B. History. The first edition of this AWWA standard, titled “Standard
Specifications for Laying Cast-Iron Pipe” (7D.1-1938), was adopted in April 1938. The
standard was published in the February 1938 edition of Journal AWWA. The standard
was revised in 1949, including a change of title to “Standard Specifications for
Installation of Cast-Iron Water Mains” (7D.1-T-1949 and C600-49T). The standard
was expanded by adding numerous tables and installation guidelines. The model
addendum was also expanded. The revised standard was published in the December
1949 edition of Journal AWWA. Section 9b, Joining of Mechanical-Joint Pipe, was
added in May 1954. Section 9c, Joining of Push-On Joint Pipe, was added in 1964.
In 1975, the AWWA Standards Council formed the present C600 committee to
revise AWWA C600 to reflect current practices and to add ductile iron as a pipe
material. To do this, the committee decided to completely change the character of the
standard, removing the model addendum and making the standard consistent with
the style of other AWWA standards.
In 1980, an addendum to the standard was approved that revised parts of
Sec. 3.4 regarding mechanical-joint assembly.
The revisions made in the 1982 edition included the elimination of references to
gray cast-iron pipe as a material for new pipeline installation, because it was no
longer being manufactured for water utility service. Also, metric conversions
were included in the 1982 revision; these were direct conversions of customary US
inch–pound units, rather than those shown in International Organization for
Standardization (ISO) standards.
The revisions made in 1987 included new references, a caveat against prolonged
exposure of polyethylene film to sunlight, revised sections on thrust restraint and
hydrostatic testing, and a discussion on making service taps on polyethylene-encased
iron mains. The standard was revised again in 1993 and approved by the AWWA
Board of Directors on June 6, 1993.
I.C. Acceptance. In May 1985, the US Environmental Protection Agency
(USEPA) entered into a cooperative agreement with a consortium led by NSF
International (NSF) to develop voluntary third-party consensus standards and a
certification program for all direct and indirect drinking water additives. Other
members of the original consortium included the American Water Works Association
Research Foundation (AWWARF) and the Conference of State Health and Environ-
mental Managers (COSHEM). The American Water Works Association (AWWA) and
the Association of State Drinking Water Administrators (ASDWA) joined later.
vii

In the United States, authority to regulate products for use in, or in contact with,
drinking water rests with individual states.* Local agencies may choose to impose
requirements more stringent than those required by the state. To evaluate the
health effects of products and drinking water additives from such products, state and
local agencies may use various references, including
1. An advisory program formerly administered by USEPA, Office of Drinking
Water, discontinued on Apr. 7, 1990.
2. Specific policies of the state or local agency.
3. Two standards developed under the direction of NSF, ANSI†/NSF‡ 60,
Drinking Water Treatment Chemicals—Health Effects, and ANSI/NSF 61, Drinking
Water System Components—Health Effects.
4. Other references, including AWWA standards, Food Chemicals Codex, Water
Chemicals Codex,§ and other standards considered appropriate by the state or local
agency.
Various certification organizations may be involved in certifying products in
accordance with ANSI/NSF 60 (61). Individual states or local agencies have authority
to accept or accredit certification organizations within their jurisdiction. Accredita-
tion of certification organizations may vary from jurisdiction to jurisdiction.
Appendix A, “Toxicology Review and Evaluation Procedures,” to ANSI/NSF 60 (61)
does not stipulate a maximum allowable level (MAL) of a contaminant for substances
not regulated by a USEPA final maximum contaminant level (MCL). The MALs of
an unspecified list of “unregulated contaminants” are based on toxicity testing
guidelines (noncarcinogens) and risk characterization methodology (carcinogens).
Use of Appendix A procedures may not always be identical, depending on the certifier.
AWWA C600-99 does not address additives requirements. Thus, users of this
standard should consult the appropriate state or local agency having jurisdiction in
order to:
1. Determine additives requirements, including applicable standards.
2. Determine the status of certifications by all parties offering to certify
products for contact with, or treatment of, drinking water.
3. Determine current information on product certification.
II. Special Issues. AWWA C600-99, Standard for Installation of Ductile-Iron
Water Mains and Their Appurtenances, can be used as a reference when making
extensions to existing distribution or transmission systems or when constructing new
distribution or transmission systems using ductile-iron mains with either mechanical
or push-on joints. It is not intended for this standard to be used as a contract
document, but it may be used as a reference in contract documents. It is based upon
a consensus of the committee on the minimum practice consistent with sound,
economical service under normal conditions, and its applicability under any
circumstances must be reviewed by a responsible engineer. The standard is not
*Persons in Canada, Mexico, and non-North American countries should contact the
appropriate authority having jurisdiction.
†American National Standards Institute, 11 W. 42nd St., New York, NY 10036.
‡NSF International, 3475 Plymouth Rd., Ann Arbor, MI 48106.
§Both publications available from National Academy of Sciences, 2102 Constitution Ave.
N.W., Washington, DC 20418.
viii

intended to preclude the manufacture, marketing, purchase, or the use of any
product, process, or procedure.
III. Use of This Standard. AWWA has no responsibility for the suitability or
compatibility of the provisions of this standard to any intended application by any
user. Accordingly, each user of this standard is responsible for determining that the
standard’s provisions are suitable for and compatible with that user’s intended
application.
III.A. Purchaser Options and Alternatives. Supplemental information is
required when using this standard, including, but not limited to, detailed plans and
specifications. The specifications should contain, at a minimum, detailed instructions
pertaining to all references in this standard that include the wording “as specified”
and “in accordance with the purchaser’s specifications.”
III.B. Modification to Standard. Any modification of the provisions, defini-
tions, or terminology in this standard must be provided in the purchaser’s
specifications.
IV. Major Revisions. There are no major revisions of this standard.
V. Comments. If you have any comments or questions about this standard,
please call the AWWA Volunteer and Technical Support Department, (303) 794-7711
ext. 6283, FAX (303) 795-7603, or write to the department at 6666 W. Quincy Ave.,
Denver, CO 80235.
ix

This page intentionally blank.

American Water Works Association
ANSI/AWWA C600-99
(Revision of ANSI/AWWA C600-93)
AWWA STANDARD FOR
INSTALLATION OF DUCTILE-IRON
WATER MAINS AND THEIR
APPURTENANCES
SECTION 1: GENERAL
Sec. 1.1 Scope
This standard covers installation procedures for ductile-iron mains and their
appurtenances for water service.
1.1.1 Conditions not discussed. Installations that require special attention,
techniques, and materials are not discussed. Each of these installations requires
special considerations based on many influencing factors that cannot be discussed
adequately in a single standard. These installations can be performed by a competent
engineering designer, including consultation with representatives of the material
manufacturing industry. Some of these installations include the following:
1. Piping through rigid walls.
2. Piping on supports above or below ground.
3. Piping requiring insulation.
4. Treatment plant or pump-station piping.
5. Industrial piping.
6. Piping through geologically hazardous areas.
7. Piping in high-density-stray-current environments.
8. Piping through corrosive soil.
9. Piping through unstable soil.
Sec. 1.2 Purpose
The purpose of this standard is to provide the minimum requirements for the
installation of ductile-iron water mains and their appurtenances, including materials,
dimensions, tolerances, and testing procedures.

2 AWWA C600-99
Sec. 1.3 Application

This standard can be referenced in specifications for installing ductile-iron
water mains and their appurtenances. The stipulations of this standard apply when
this document has been referenced and then only to the installation of ductile-iron
water mains and their appurtenances.
SECTION 2: REFERENCES
This standard references the following documents. In their latest editions, they
form a part of this standard to the extent specified within this standard. In any case
of conflict, the requirements of this standard shall prevail.
AASHTO T99*—Standard Specifications for the Moisture-Density Relations of
Soils Using a 5.5-lb. (2.5-kg) Rammer and a 12-in. (305-mm) Drop.
ANSI†/AWWA C105/A21.5—American National Standard for Polyethylene
Encasement for Ductile-Iron Pipe Systems.
ANSI/AWWA C111/A21.11—American National Standard for Rubber-Gasket
Joints for Ductile-Iron Pressure Pipe and Fittings.
ANSI/AWWA C150/A21.50—American National Standard for the Thickness
Design of Ductile-Iron Pipe.
ANSI/AWWA C500—Standard for Metal-Seated Gate Valves for Water Supply
Service.
ANSI/AWWA C509—Standard for Resilient-Seated Gate Valves for Water
Supply Service.
ANSI/AWWA C651—Standard for Disinfecting Water Mains.
AWWA Manual M3, Safety Practices for Water Utilities (1990).
AWWA Manual M17, Installation, Field Testing, and Maintenance of Fire
Hydrants (1989).
AWWA Manual M27, External Corrosion—Introduction to Chemistry and
Control (1986).
The reader of AWWA C600 is referred to the following standards for additional
information on the use or limitations of specific products.
ANSI/AWWA C104/A21.4—American National Standard for Cement-Mortar
Lining for Ductile-Iron Pipe and Fittings for Water.
ANSI/AWWA C110/A21.10—American National Standard for Ductile-Iron and
Gray-Iron Fittings, 3 In. Through 48 In. (75 mm Through 1,200 mm), for Water.
ANSI/AWWA C115/A21.15—American National Standard for Flanged
Ductile-Iron Pipe with Ductile-Iron or Gray-Iron Threaded Flanges.
ANSI/AWWA C151/A21.51—American National Standard for Ductile-Iron Pipe,
Centrifugally Cast, for Water.
ANSI/AWWA C153/A21.53—American National Standard for Ductile-Iron
Compact Fittings, 3 In. Through 24 In. (76 mm Through 610 mm) and 54 In. Through
64 In. (1,400 mm Through 1,600 mm), for Water Service.
* American Association of State Highway and Transportation Officials, 444 N. Capitol St. N.W.,
Ste. 225, Washington, DC 20001.
†American National Standards Institute, 11 W. 42nd St., New York, NY 10036.

DUCTILE-IRON MAINS AND APPURTENANCES 3
ANSI/AWWA C502—Standard for Dry-Barrel Fire Hydrants.

ANSI/AWWA C503—Standard for Wet-Barrel Fire Hydrants.
ANSI/AWWA C504—Standard for Rubber-Seated Butterfly Valves.
ANSI/AWWA C800—Standard for Underground Service Line Valves and Fit-
tings.
Handbook of Occupational Safety and Health Standards for Water Utilities.
AWWA, Denver, Colo.
OSHA 29 CFR 1986*—Health Regulations for Construction.
SECTION 3: DEFINITIONS
The following definitions shall apply in this standard:
1. Ductile iron: Cast ferrous material in which a major part of the carbon
content occurs as free graphite in a substantially nodular or spheroidal form.
2. Cast iron: Cast ferrous material in which a major part of the carbon
content occurs as graphitic carbon in the form of flakes interspersed through the
metal.
3. Manufacturer: The party that manufactures, fabricates, or produces mate-
rials or products.
4. Mechanical joint: The gasketed and bolted joint as detailed in ANSI/
AWWA C111/A21.11.
5. Plans: Drawings normally prepared by an engineer employed or retained
by the ultimate system-operating company showing the location and details for the
construction of the pipeline and appurtenances.
6. Push-on joint: The single rubber-gasket joint as described in ANSI/AWWA
C111/A21.11.
SECTION 4: REQUIREMENTS
Sec. 4.1 Permeation
The selection of materials is critical for water service and distribution piping in
locations where the pipe will be exposed to significant concentrations of pollutants
composed of low-molecular-weight petroleum products or organic solvents or their
vapors. Pipe materials such as polyethylene, polybutylene, polyvinyl chloride, and
asbestos–cement and elastomers, such as used in jointing gaskets and packing
glands, may be subject to permeation by lower-molecular-weight organic solvents or
petroleum products. If a water pipe must pass through a contaminated area or an
area subject to contamination, consult with the manufacturer regarding permeation
of pipe walls, jointing materials, etc., before selecting materials for use in that area.
* Occupational Safety and Health Administration, Code of Federal Regulations; available from
Government Printing Office, 720 N. Main, Pueblo, CO 81003.

4 AWWA C600-99
Sec. 4.2 Installing Ductile-Iron Mains

4.2.1 Alignment and grade. The water mains shall be laid and maintained on
lines and grades established by the plans and specifications for the project. Fittings,
valves, tapped or bossed outlets, and hydrants must be installed at the required
locations unless field conditions warrant otherwise, and these changes are approved
in accordance with the specifications. Valve-operating stems shall be oriented to
allow proper operation. Hydrants shall be installed plumb.
4.2.1.1 Prior investigation. Prior to excavation, an investigation shall be
conducted to determine the location of existing underground structures and conflicts.
During excavation, damage to existing structures should be avoided. Special
precautions shall be taken when the water main being installed crosses or is adjacent
to a facility that is cathodically protected.
4.2.1.2 Unforeseen obstructions. When obstructions not indicated on the
plans interfere with the progress of work, an alteration of the plans is required.
These alterations or deviation in line and grade, or the removal, relocation, or
reconstruction of the obstructions shall be performed in accordance with the
specifications.
4.2.1.3 Clearance. When crossing existing pipelines or other structures,
alignment and grade shall be adjusted as necessary, in accordance with the
specifications, to provide clearance as required by federal, state or provincial, and
local regulations or as deemed necessary to prevent future damage or contamination
of either structure.
4.2.2 Trench construction. The trench shall be excavated to the required
alignment, depth, and width specified or shown on the plans and shall conform with
all federal, state or provincial, and local regulations for the protection of the workers.
4.2.2.1 Trench preparation. Trench preparation shall proceed in advance of
pipe installation as stated in the specifications.
4.2.2.1.1 Discharges from trench dewatering pumps shall be directed away
from the trench to prevent trench instability and shall be in accordance with federal,
state or provincial, and local point-discharge requirements.
4.2.2.1.2 Excavated material shall be placed in a manner that will not
obstruct the work nor endanger the workers or the public, or obstruct sidewalks,
driveways, roadways, or other structures. Excavated material shall be placed in
compliance with federal, state or provincial, and local regulations.
4.2.2.2 Pavement removal. Pavement and road surfaces shall be removed as
part of the trench excavation. The amount removed shall depend on the width of
trench required for the installation of the pipe and the dimensions of the area into
which valves, hydrants, specials, manholes, or other structures will be installed. The
dimensions of pavement removed shall not exceed the dimensions of the opening
required for installation of pipe, valves, hydrants, specials, manholes, and other
structures by more than 6 in. (150 mm) in any direction, unless otherwise stipulated
in the specifications. Sawing, drilling, or chipping shall be used to ensure the
breakage of pavement along straight lines.
4.2.2.3 Width. The width of the trench at the top of the pipe shall equal the
single-pass capabilities of normally available excavating equipment. The width shall
permit the pipe to be laid and joined properly and to allow the backfill to be placed in
accordance with the specifications. Trench widths shown in Table 1 may be used as a
guide. When required, trenches shall be wider to permit the placement of timber
supports, sheeting, bracing, and appurtenances as required by the safety require-
ments of the agency having jurisdiction.

Table 1 Suggested trench widths at the top of the pipe
Nominal Pipe Size Trench Width

in. (mm) in. (m)
3 and 4 (76 and 102) 28 (0.71)
6 (152) 30 (0.76)
8 (203) 32 (0.81)
10 (254) 34 (0.86)
12 (305) 36 (0.91)
14 (356) 38 (0.97)
16 (406) 40 (1.02)
18 (457) 42 (1.07)
20 (508) 44 (1.12)
24 (610) 48 (1.22)
30 (762) 54 (1.37)
36 (914) 60 (1.52)
42 (1,067) 66 (1.68)
48 (1,219) 72 (1.83)
54 (1,400) 78 (1.98)
60 (1,500) 84 (2.13)
64 (1,600) 88 (2.24)
4.2.2.4 Bell holes. Holes for the bells shall be provided at each joint, and
they shall be no larger than necessary to allow joint assembly and to ensure that the
pipe barrel will lie flat on the trench bottom. The dimensions of bell-hole depressions
for push-on type joints should be large enough to ensure that the pipe is not resting
on the bells and is supported by the full length of the pipe barrel.
4.2.2.4.1 Other than noted previously, the trench bottom shall be true and even
to provide support for the full length of the pipe barrel. A slight depression may be
provided to allow withdrawal of pipe slings or other lifting tackle without damaging
coating or polyethylene encasement.
4.2.2.5 Rock conditions. When excavation of rock is necessary, all rock shall
be removed to provide a clearance below and on each side of all pipe, valves, and
fittings of at least 6 in. (150 mm) for nominal pipe sizes 24 in. (610 mm) or smaller
and 9 in. (230 mm) for nominal pipe sizes 30 in. (762 mm) and larger. When
excavation is completed, a layer of appropriate backfill material (see Sec. 4.2.5) shall
be placed on the bottom of the trench to the appropriate depths, then leveled and
tamped.
4.2.2.5.1 These clearances and bedding procedures shall also be observed for
pieces of concrete or masonry and other debris or subterranean structures, such as
masonry walls, piers, or foundations that may be encountered during excavation.
4.2.2.5.2 This installation procedure shall be followed when gravel formations
containing loose cobbles or boulders greater than approximately 8 in. (200 mm) in
diameter are encountered.
4.2.2.5.3 In all cases, the specified clearances shall be maintained between the
bottom of all pipe and appurtenances and any part, projection, or point of rock,

6 AWWA C600-99
boulder, or stone of sufficient size and placement that could cause a fulcrum point or
pointload.
4.2.2.6 Previous excavations. If the trench passes over a previous excavation,
such as a sewer, the trench bottom shall be sufficiently compacted to provide support
equal to that of the native soil or conform to other regulatory requirements in a
manner that will prevent damage to the existing installation.
4.2.2.7 Blasting. Blasting for excavation shall be permitted only after
securing approval(s) and establishing the hours of blasting as required by the
specifications. The blasting procedure, including protection of persons and property,
shall be in strict accordance with federal, state or provincial, and local regulations.
4.2.2.8 Protecting property. Trees, shrubs, fences, and all other property and
surface structures shall be protected during construction, unless their removal is
shown in the plans and specifications.
4.2.2.8.1 Any cutting of tree roots or branches shall be performed in
accordance with the specifications.
4.2.2.8.2 Temporary support, adequate protection, and maintenance of all
underground and surface structures, drains, sewers, and other obstructions encoun-
tered during the work shall be provided in accordance with specifications or
applicable regulations.
4.2.2.8.3 All properties that have been disturbed shall be restored as
completely as practical to their original condition.
4.2.2.9 Unsuitable material. When the material is found to include ashes,
cinders, refuse, organic material, or other unsuitable material, this material shall be
removed to a minimum of at least 6 in. (150 mm) below the bottom of the pipe or to
the depth required by the specifications. The removed material shall be replaced with
clean, stable backfill material. When these potentially corrosive materials are
encountered, polyethylene encasement should be used to protect the pipe (see
Sec. 4.2.3.8). The bedding shall be consolidated and leveled so that the pipe may be
installed in accordance with Sec. 4.2.2.4.
4.2.2.10 Unstable material. When the bottom of the trench consists of
material that is unstable to such a degree that its removal is impractical, a
foundation for the pipe or appurtenance shall be constructed using piling, treated
timber, concrete, or other materials, in accordance with the specifications.
4.2.2.11 Traffic Control. Appropriate traffic-control devices shall be provided
in accordance with federal, state or provincial, and local regulations to regulate,
warn, and guide traffic at the work site.
4.2.3 Installing pipe. The proper implements, tools, and facilities shall be
provided and used for the safe and convenient performance of the work. All pipe,
fittings, valves, and hydrants shall be lowered carefully into the trench using a
backhoe, a crane, ropes, or other suitable tools or equipment, in such a manner as to
prevent damage to water main materials and protective coatings and linings. Under
no circumstances shall water main materials be dropped or dumped into the trench.
Where practical, the trench should be dewatered prior to installation of the pipe.
4.2.3.1 Examining material. All pipe, fittings, valves, hydrants, and other
appurtenances shall be examined carefully for damage and other defects immediately
before installation. Defective materials shall be marked and held for final disposition
as required by the specifications.
4.2.3.2 Pipe ends. All lumps, blisters, and excess coating shall be removed
from the socket and plain ends of each pipe, and the outside of the plain end and the

inside of the bell shall be wiped clean and dry and be free from dirt, sand, grit, or any
foreign materials before the pipe is laid.
4.2.3.3 Pipe cleanliness. Foreign material shall be prevented from entering
the pipe while it is being placed in the trench. No debris, tools, clothing, or other
materials shall be placed in the pipe at any time.
4.2.3.4 Pipe placement. As each length of pipe is placed in the trench, the
joint shall be assembled and the pipe brought to correct line and grade. The pipe
shall be secured in place with approved backfill material.
4.2.3.5 Direction of bells. It is common practice to lay pipe with the bells
facing the direction in which work is progressing; however, it is not mandatory. For
example, when the main is being laid on a slope, the pipe is frequently laid with the
bells facing uphill for ease of installation. The direction of the bells is not functionally
related to the direction of flow within the main.
4.2.3.6 Pipe plugs. At times when pipe-laying is not in progress, the open
ends of pipe shall be closed by a watertight plug or other means as specified. The plug
shall be fitted with a means for venting. When practical, the plug shall remain in
place until the trench is pumped completely dry. Care must be taken to prevent pipe
flotation, if the trench fills with water.
4.2.3.6.1 Prior to removal of the plug for extending the line or for any other
reason, air and/or water pressure in the line shall be released.
4.2.3.7 Ductile-iron laying conditions. The laying conditions for ductile-iron
pipe shall be completed in accordance with ANSI/AWWA C150/A21.50 as illustrated
in Figure 1 of this standard and as required by the specifications.
4.2.3.7.1 Loosely placed backfill above the pipe may allow settlement that
could be detrimental to improvements subsequently placed over the trench.
4.2.3.8 For any installation requiring polyethylene encasement for corrosion
protection of ductile-iron pipe, the encasement shall be installed in accordance with
ANSI/AWWA C105/A21.5.
4.2.3.9 For installations requiring other forms of corrosion protection, refer to
AWWA Manual M27.
4.2.3.10 Special transition couplings or gaskets are required for joining
different types of pipe, such as steel pipe, asbestos–cement pipe, and plastic pipe.
These transition devices are available. When ordering, the actual outside diameter of
the pipe should be provided.
4.2.4 Joint assembly.
4.2.4.1 Push-on joints. Push-on joints shall be assembled as described and
illustrated in Figure 2.
4.2.4.2 Mechanical joints. Mechanical joints shall be assembled as described
and illustrated in Figure 3 and Table 2.
4.2.4.3 Joint deflection. When it is necessary to deflect pipe from a straight
line in either the horizontal or vertical plane, the amount of joint deflection shall not
exceed that shown in Tables 3 and 4. The deflections listed are maximum deflections
and should not be exceeded. For design purposes, deflection should be limited to 80
percent of the values shown. Figure 4 illustrates the maximum offset S and
approximate radius curve R, which are listed in Tables 3 and 4.

8 AWWA C600-99
Type 1* Type 2
Flat-bottom trench.† Loose backfill. Flat-bottom trench.† Backfill lightly consolidated to
centerline of pipe.
Type 3
Pipe bedded in 4 in. (100 mm) minimum of loose soil.‡
Backfill lightly consolidated to top of pipe.
Type 4 Type 5
Pipe bedded in sand, gravel, or crushed stone to depth Pipe bedded in compacted granular material to
of 1/8 pipe diameter, 4 in. (100 mm) minimum. Backfill centerline of pipe. Compacted granular or select
compacted to top of pipe. (Approximately 80 percent material‡ to top of pipe. (Approximately 90 percent
Standard Proctor, AASHTO T-99.) Standard Proctor, AASHTO T-99.)
*For 14-in. (355-mm) and larger pipe, consideration should be given to the use of laying conditions other than type 1.
†“Flat-bottom” is defined as undisturbed earth.
‡“Loose soil” or “select material” is defined as native soil excavated from the trench, free of rocks, foreign materials, and
frozen earth.
Figure 1 Laying conditions for ductile-iron pipe

1. Thoroughly clean the groove and the bell socket of the 2. Apply lubricant to the gasket and plain end of the pipe
pipe or fitting; also clean the plain end of the mating pipe. in accordance with the pipe manufacturer’s
Using a gasket of the proper design for the joint to be recommendations. Lubricant is furnished in sterile
assembled, make a small loop in the gasket and insert it containers, and every effort should be made to protect
in the socket, making sure the gasket faces the correct against contamination of the container’s contents.
direction and that it is properly seated. NOTE: In cold
weather, it is necessary to warm the gasket to facilitate
insertion.
3. Be sure that the plain end is beveled; square or sharp

edges may damage or dislodge the gasket and cause a
leak. When pipe is cut in the field, bevel the plain end with
a heavy file or grinder to remove all sharp edges. Push the
plain end into the bell of the pipe. Keep the joint straight
while pushing. Make deflection after the joint is assembled.
4. Small pipe can be pushed into the bell socket with a

long bar. Large pipe requires additional power, such as a
jack, lever puller, or backhoe. The supplier may provide a
jack or lever puller on a rental basis. A timber header
should be used between the pipe and jack or backhoe
bucket to avoid damage to the pipe.
Figure 2 Push-on-joint assembly

10 AWWA C600-99
1. Clean the socket and the plain end. Lubrication and

additional cleaning should be provided by brushing both
the gasket and plain end with soapy water or an
2. Insert the pipe into the socket and press the gasket
approved pipe lubricant meeting the requirements of
firmly and evenly into the gasket recess. Keep the joint
ANSI/AWWA C111/A21.11, just prior to slipping the
straight during assembly.
gasket onto the plain end for joint assembly. Place the
gland on the plain end with the lip extension toward the
plain end, followed by the gasket with the narrow edge
of the gasket toward the plain end.
3. Push the gland toward the socket and center it around 4. Tighten the bolts to the normal range of bolt torque
the pipe with the gland lip against the gasket. Insert bolts as indicated in Table 3 while at all times maintaining
and hand-tighten nuts. Make deflection after joint assembly approximately the same distance between the gland
but before tightening bolts. and the face of the flange at all points around the
socket. This can be accomplished by partially tightening
the bottom bolt first, then the top bolt, next the bolts at
either side, finally the remaining bolts. Repeat the
process until all bolts are within the appropriate range
of torque. In large sizes (30–48 in. [762–1219 mm]), five
or more repetitions may be required. The use of a
torque-indicating wrench will facilitate this procedure.
Figure 3 Mechanical-joint assembly

Table 2 Mechanical-joint bolt torque
Joint Size Bolt Size Range of Torque

in. (mm) in.
5/8
mm ⋅
ft lb (N m)⋅
3 (76) (16) 45–60 (61–81)
3
4–24 (102–610) /4 (19) 75–90 (102–122)
30–36 (762–914) 111 (25) 100–120 (136–163)
42–48 (1,067–1,219) 11/4 (32) 120–150 (163–203)
Figure 4 Pipeline curve geometry

12 AWWA C600-99
Table 3 Maximum joint deflection* full-length pipe—push-on-type joint pipe
Approx. Radius of Curve—R†

†
Nominal Deflection Maximum Offset—S Produced by Succession of Joints
Pipe Size Angle—Θ in. (m) ft (m)
L†=18 ft L†=20 ft L†=18 ft L†=20 ft

in. (mm) deg. (5.5 m) (6 m) (5.5 m) (5 m)
3 12,(76) 5 19 (0.48) 21 (0.53) 205 1(62) 230 1(70)
4 1,(102) 5 19 (0.48) 21 (0.53) 205 1(62) 230 1(70)
6 1,(152) 5 19 (0.48) 21 (0.53) 205 1(62) 230 1(70)
8 1,(203) 5 19 (0.48) 21 (0.53) 205 1(62) 230 1(70)
10 1,(254) 5 19 (0.48) 21 (0.53) 205 1(62) 230 1(70)
12 1,(305) 5 19 (0.48) 21 (0.53) 205 1(62) 230 1(70)
*
14 1,(356) 3 11 (0.28) 12 (0.30) 340 (104) 380 (116)
16 1,(406) 3* 11 (0.28) 12 (0.30) 340 (104) 380 (116)
*
18 1,(457) 3 11 (0.28) 12 (0.30) 340 (104) 380 (116)
20 1,(508) 3* 11 (0.28) 12 (0.30) 340 (104) 380 (116)
*
24 1,(610) 3 11 (0.28) 12 (0.30) 340 (104) 380 (116)
30 1,(762) 3* 11 (0.28) 12 (0.30) 340 (104) 380 (116)
*
36 1,(914) 3 11 (0.28) 12 (0.30) 340 (104) 380 (116)
42 (1,067) 3* 11 (0.28) 12 (0.30) 340 (104) 380 (116)
*
48 (1,219) 3 12 (0.30) 380 (116)
54 (1,400) 3* 12 (0.30) 380 (116)
*
60 (1,500) 3 12 (0.30) 380 (116)
64 (1,600) 3* 12 (0.30) 380 (116)
*For 14-in. and larger push-on joints, maximum deflection angle may be larger than shown above. Consult the
manufacturer.
†See Figure 4.
4.2.4.4 Pipe cutting. Cutting pipe for insertion of valves, fittings, or closure
pieces shall conform to all safety recommendations of the manufacturer of the cutting
equipment. Cutting shall be done in a safe, professional manner to prevent damage
to the pipe or cement–mortar lining.
4.2.4.4.1 Existing gray-iron pipe may be cut using a hydraulic squeeze cutter,
abrasive pipe saw, rotary wheelcutter, guillotine pipe saw, or milling wheel saw.
4.2.4.4.2 Ductile-iron pipe may be cut using an abrasive pipe saw, rotary
wheelcutter, guillotine pipe saw, milling wheel saw, or oxyacetylene torch if
recommended by the pipe manufacturer.
4.2.4.4.3 Cut ends and rough edges shall be ground smooth, and, for push-on
joint connections, the cut end shall be beveled by methods recommended by the
manufacturer.
4.2.4.4.4 ANSI/AWWA C151/A21.51 requires factory gauging of the spigot end
to ensure that the outside diameter of each spigot end falls within the tolerances
stipulated in that standard. Accordingly, pipes selected for cutting should be field-
gauged. A mechanical-joint (MJ) gland inserted over the barrel might serve as a
convenient indicator for this purpose. When glands are not available, pipe can be

Table 4 Maximum joint deflection full-length pipe—mechanical-joint pipe
Approx. Radius of Curve—R*

*
Nominal Deflection Maximum Offset—S Produced by Succession of Joints
Pipe Size Angle—Θ in. (m) ft (m)
L*=18 ft L*=20 ft L*=18 ft L*=20 ft

in. (mm) deg. (5.5 m) (6 m) (5.5 m) (6 m)
13 1(76) 8–18 31 (0.79) 35 (0.89) 125 1(38) 140 1(43)
14 (102) 8–18 31 (0.79) 35 (0.89) 125 1(38) 140 1(43)
16 (152) 7–07 27 (0.69) 30 (0.76) 145 1(44) 160 1(49)
18 (203) 5–21 20 (0.51) 22 (0.56) 195 1(59) 220 1(67)
10 (254) 5–21 20 (0.51) 22 (0.56) 195 1(59) 220 1(67)
12 (305) 5–21 20 (0.51) 22 (0.56) 195 1(59) 220 1(67)
14 (356) 3–35 13.5 (0.34) 15 (0.38) 285 1(87) 320 1(98)
16 (406) 3–35 13.5 (0.34) 15 (0.38) 285 1(87) 320 1(98)
18 (457) 3–00 11 (0.28) 12 (0.30) 340 (104) 380 (116)
20 (508) 3–00 11 (0.28) 12 (0.30) 340 (104) 380 (116)
24 (610) 2–23 19 (0.23) 10 (0.25) 450 (137) 500 (152)
*See Figure 4.
selected by measuring with a tape in accordance with the manufacturer’s recommen-

dation.
4.2.5 Backfilling. Backfill shall be accomplished in accordance with the
specified laying conditions as described in Sec. 4.2.3.
4.2.5.1 Backfill material. All backfill material shall be free from cinders,
ashes, refuse, vegetable or organic material, boulders, rocks or stones, frozen soil, or
other unsuitable material.
4.2.5.1.1 From 1 ft (300 mm) above the top of the pipe to the subgrade of the
pavement, material containing stones up to 8 in. (200 mm) in their greatest
dimension may be used, unless otherwise specified.
4.2.5.1.2 When the type of backfill material is not indicated on the plans or is
not specified, the excavated material may be used, provided that this material
consists of loam, clay, sand, gravel, or other suitable materials.
4.2.5.1.3 If excavated material is indicated on the drawings or specified for
backfill, and there is a deficiency because a part of that material has been rejected,
the required amount of sand, gravel, or other approved material shall be provided.
4.2.5.1.4 For purposes of definition: (a) sand is material graded from fine to
coarse, containing less than 10 percent by weight of loam and clay that passes a 3/4-in.
(19-mm) sieve with no more than 5 percent by weight remaining on a US No. 4 sieve;
(b) gravel is a reasonably uniform combination, containing no boulders or stones
larger than 2 in. (50 mm) and not containing excessive amounts of clay and loam;
(c) crushed stone is limestone or dolomite ledge-rock material that all passes a 1/2-in.
(13-mm) sieve with no more than 25 percent passing a US No. 100 sieve.
4.2.5.2 Compaction. When special backfill compaction procedures are
required, they shall be performed in accordance with project specifications or
applicable federal, state or provincial, and local regulations.
4.2.5.3 Partial backfilling during testing. Newly installed pipelines are
normally tested after backfilling. When unusual conditions require that pressure and

14 AWWA C600-99
leakage testing be performed before completion of backfilling or with pipe joints

accessible for examination, sufficient backfill material shall be placed over the pipe
barrel between the joints to prevent movement with consideration given to
restraining thrust forces during the testing. In particular, restrained-joint systems,
which derive their stability from the interaction of the pipe and soil, should be
backfilled prior to testing.
4.2.5.4 If polyethylene encasement is used, any damage that occurs to the
wrap shall be repaired in accordance with ANSI/AWWA C105/A21.5.
4.2.6 Valve and fitting installation.
4.2.6.1 Examining material. Prior to installation, valves shall be inspected
for direction of opening, number of turns to open, freedom of operation, tightness of
pressure-containing bolting and test plugs, cleanliness of valve ports, and especially
seating surfaces, handling damage, and cracks. Defective valves shall be marked and
held for final disposition as required by the specifications. All bolts and nuts, with the
exception of seat adjusting bolts or screws in butterfly valves, shall be checked for
proper tightness. Seat adjusting bolts in butterfly valves shall only be adjusted on the
recommendation from the manufacturer.
4.2.6.2 Placement. Valves, fittings, plugs, and caps shall be set and joined to
the pipe according to Sec. 4.2.3 for cleaning and laying, and to Sec. 4.2.4 for joining
pipe. Valves, 12 in. (305 mm) and larger, should be provided with special support,
such as treated timbers, crushed stone, concrete pads, or a sufficiently tamped trench
bottom so that the pipe will not be required to support the weight of the valve. Valves
installed aboveground or in plant piping systems shall be supported to prevent
bending of the valve end connections as a result of pipe loading. Valves shall be
installed in the closed position.
4.2.6.3 Valve location. Valves in water mains shall, where practical, be
located within or immediately adjacent to the street property lines unless shown
otherwise on the plans.
4.2.6.3.1 Mains shall be drained through drainage branches or blowoffs.
Drainage branches, blowoffs, and appurtenances shall be provided with control
valves and shall be located and installed as shown on the plans. Drainage branches
or blowoffs shall not be directly connected to any storm or sanitary sewer, submerged
in any stream, or be installed in any other manner that will permit backsiphonage
into the distribution system.
4.2.6.3.2 Air-release or vacuum vents shall be provided at high points in the
line and in areas of potential negative pressure. The air release or vacuum vents
shall not be connected to any storm or sanitary sewer, and they shall be protected
from freezing in cold locations.
4.2.6.4 Valve protection. A valve box or a vault shall be provided for every
valve.
4.2.6.4.1 A valve box shall be provided for every valve that has no gearing or
operating mechanism or in which the gearing or operating mechanism is fully
protected with a gear case. The valve box shall not transmit shock or stress to the
valve. The valve box shall be centered over the operating nut of the valve, with the
box cover flush with the surface of the finished area or another level as specified.
4.2.6.4.2 A valve vault designed to prevent settling on the pipe shall be
provided for every valve that has exposed gearing or operating mechanisms. The
operating nut shall be readily accessible for operation through the opening in the
valve vault. The opening shall be set flush with the surface of the finished pavement
or another level as specified. Vaults shall be constructed to permit minor valve

repairs and to protect the valve and pipe from impact where they pass through the
vault walls.
4.2.6.4.3 In no case shall valves be used to bring misaligned pipe into
alignment during installation. Pipe shall be supported to prevent stress on the valve.
4.2.6.4.4 Thrust resulting from closure of valves shall be carefully considered
in the design of the piping system and vaults.
4.2.6.5 Plugs and caps. All dead ends on new mains shall be closed with
plugs or caps that are suitably restrained to prevent blowing off under test pressure.
If a blowoff valve precedes the plug or cap, it too shall be restrained against blowing
off. All dead ends shall be equipped with suitable blowoff or venting devices.
4.2.6.6 Additional information. Additional information regarding installation
of gate valves can be found in the appendixes of ANSI/AWWA C500 and ANSI/
AWWA C509.
4.2.7 Installing hydrants.
4.2.7.1 Examining materials. Prior to installation, all hydrants shall be
inspected for direction of opening, nozzle threading, operating-nut and cap-nut
dimensions, tightness of pressure-containing bolting, cleanliness of inlet elbow,
handling damage, and cracks. Defective hydrants shall be marked and held for final
disposition required by the specifications.
4.2.7.2 Placing hydrants. All hydrants shall stand plumb and shall have their
nozzles parallel with or at right angles to the curb, with the pumper nozzle facing the
curb. Hydrants having two-hose nozzles 90° apart shall be set with each nozzle facing
the curb at an angle of 45°.
4.2.7.2.1 Hydrants shall be set to the established grade, with the lowest nozzle
at least 12 in. (300 mm) above the ground or as required by the specifications. The
lowest nozzle shall be installed away from the curb line at a sufficient distance to
avoid damage from or to vehicles. Traffic-model hydrants (hydrants that are intended
to fail at the ground line on vehicle impact) shall be installed so that the breakaway
flange is not less than 2 in. (50 mm), nor more than 6 in. (150 mm), above the
established grade.
4.2.7.2.2 Each hydrant shall be connected to the main with a 6-in. (152-mm) or
larger-diameter branch controlled by an independent valve, unless otherwise
specified. The valve shall be restrained to allow shutoff when the hydrant is to be
removed.
4.2.7.2.3 When a dry-barrel hydrant is set in soil that is impervious, drainage
shall be provided at the base of the hydrant by placing coarse gravel or crushed stone
mixed with coarse sand from the bottom of the trench to at least 6 in. (150 mm) above
the drain-port opening in the hydrant and to a distance of 1 ft (300 mm) around the
elbow. Where groundwater rises above the drain port or when the hydrant is located
within 8 ft (2.4 m) (or the distance required by the applicable regulatory agency) of a
sanitary sewer main, or where drainage is not permitted by the applicable regulatory
agency, the drain port shall be plugged and water pumped from the hydrant when
freezing may occur.
4.2.7.2.4 When a dry-barrel hydrant with an open drain port is set in clay or
other impervious soil, a drainage pit 2 ft × 2 ft × 2 ft (0.6 m × 0.6 m × 0.6 m) shall be
excavated below each hydrant. The drainage pit shall be filled with coarse gravel or
crushed stone mixed with coarse sand under and around the elbow of the hydrant to
a level of 6 in. (150 mm) above the drain port. To prevent possible contamination of
the water supply, do not connect hydrant drains to a sanitary sewer or storm sewer.

16 AWWA C600-99
4.2.7.3 Location. Hydrants shall be located as shown on the plans or as

specified.
4.2.7.4 Protection. In the case of traffic hydrants, adequate soil resistance
must be provided to avoid transmitting shock moment to the lower barrel and inlet
connection. In loose or poor load-bearing soil, this may be accomplished by pouring a
concrete collar approximately 6 in. (150 mm) thick to a diameter of 2 ft (0.6 m) at or
near the ground line around the hydrant barrel.
4.2.7.5 Additional information. Additional information regarding installation
of hydrants can be found in AWWA Manual M17.
4.2.8 Thrust restraint.
4.2.8.1 Hydrants. The bowl of each hydrant shall be well braced against a
sufficient area of unexcavated earth at the end of the trench with thrust blocks of
concrete or other specified blocking materials, or it shall be tied to the pipe with suitable
metal tie rods, clamps, or restrained joints, as shown on the plans or as specified.
4.2.8.2 Fittings. All plugs, caps, tees, reducers, and bends, unless otherwise
specified, shall be provided with thrust blocks or suitably restrained joints, as shown
on the plans or as specified.
4.2.8.3 Design. The design pressure is the maximum pressure to which the
pipeline will be subjected, with consideration given to the vulnerability of the pipe–
soil system when the pressure is applied. In most cases, this will be the test pressure
of the pipe, applied shortly after installation, when the pipe–soil system is normally
most vulnerable.
For buried pipelines, thrust restraint is achieved by transferring the thrust force
to the soil structure outside the pipe. The objective of the design is to distribute the
thrust forces to the soil structure preventing joint separation in unrestrained joints.
4.2.8.4 Concrete thrust blocks. Vertical and horizontal thrust blocks shall be
made of concrete having a compressive strength of not less than 2,000 psi (13.8 MPa)
after 28 days. The blocks shall be placed between solid ground and the fitting(s) to be
anchored. The mass of the block or the area of bearing on the pipe and on the ground
in each instance shall be that shown on the plans or as specified. The blocking shall,
unless otherwise shown or specified, be located so as to contain the resultant thrust
force in such a way that the pipe and fitting joints will be accessible for repair.
4.2.8.5 Restrained joints. If indicated in the plans and specifications,
restraining mechanisms for push-on or mechanical joints may be used instead of
concrete thrust blocking. Tie rods, clamps, or other components shall be made of
corrosion resistant material or suitably protected against corrosion.
4.2.9 Flushing. Foreign material left in the pipelines during installation often
results in valve- or hydrant-seat leakage during pressure tests. The pipe lines shall
be kept clean during installation. Thorough flushing is recommended prior to a
pressure test. Flushing should be accomplished by partially opening and closing
valves and hydrants several times under expected line pressure, with flow velocities
adequate to flush foreign material out of the valves and hydrants.
Sec. 4.3 Disinfection
A newly installed main shall be disinfected in accordance with ANSI/AWWA
C651. Following chlorination, the main should be flushed as soon as possible (within
24 h), because prolonged exposure to high concentrations of chlorine might damage
the asphaltic seal coating.
NOTE: Provisions should be made to avoid contamination of existing mains by
cross connection during testing/disinfection/flushing of newly installed mains.

Sec. 4.4 Highway and Railroad Crossings

4.4.1 Casing pipe. When casing pipe is specified for highways or railroad
crossings, the project shall be completed in accordance with applicable federal, state
or provincial, and local regulations. In the case of railroad crossings, the project
should also comply with regulations established by the railroad company. General
practice permits boring for nominal casing diameters through 36 in. (914 mm) with a
maximum length of about 175 ft (53 m); jacking for nominal diameters 30 in. (762
mm) through 60 in. (1,500 mm) with lengths of about 200 ft (61 m); and tunneling for
pipes 48 in. (1,219 mm) in nominal diameter and larger for longer lengths.
4.4.2 Carrier pipe. The casing pipe should be 6–8 in. (150–200 mm) larger
than the outside diameter of the ductile-iron pipe bells. Carrier pipe may be pushed
or pulled through the completed casing pipe. Chocks or skids should be placed under
the carrier pipe to ensure approximate centering within the casing pipe and to
prevent damage during installation. Metal-to-metal contact must be avoided. End
caps or other methods of sealing the casing pipe shall be provided as specified. In
order to avoid the transfer of earth and live loads to the carrier pipe, the space
between the carrier and casing pipes should not be filled completely.
Sec. 4.5 Subaqueous Crossings
4.5.1 Subaqueous installations. When it is necessary to cross a body of water
requiring only a small deflection in the joints, and joint restraint is not a
consideration, standard mechanical-joint or push-on joint pipe can be used. If the
water is deep and the angle of deflection in the joint necessary to follow the contour
of the riverbed is great, or if changing bottom conditions are anticipated, ball-and-
socket pipe or fittings, which will deflect up to 15°, should be used. A combination of
restrained and river-crossing joints may be used, depending on bottom conditions and
service requirements.
There are several methods of installing subaqueous ductile-iron pipe. Ductile-
iron pipe can be assembled in sections of three or four lengths, either on shore or on
the deck of a barge, attached to a “strongback.” The assembly is then lowered to the
streambed where the sections are connected by divers. Ball-and-socket pipes use
joints with positive locking devices. This type of pipe can also be assembled on a
chute affixed to the barge and lowered into position as the assembly progresses.
Another method of installation is to assemble the pipeline on shore and either
drag it into position along the bottom or float it into position using barrels or floats
attached to the pipe, which are punctured or released in a controlled fashion when
the pipe reaches the desired position. Joints should not be allowed to become overly
deflected or subjected to excessive beam load during the installation process.
A similar method is to assemble the pipe on shore, attach floats, and pull the
pipe down skids into the water as each length is connected. The line extends farther
into the water as each successive length is laid, and the finished line is submerged
appropriately.
Subaqueous lines laid in navigable streams must be placed in trenches and
covered to protect them from damage or displacement by ship or boat traffic. Where
applicable, procedures should conform to appropriate governmental regulations.

18 AWWA C600-99
Sec. 4.6 Service Taps

4.6.1 Tapping. Corporation stops may be installed either before or after pipe
installation. Generally, they are located at ten o’clock or two o’clock on the
circumference of the pipe* and may be screwed directly into the tapped and threaded
main without any additional appurtenances. When more than one tap is necessary to
deliver the required flow in an existing gray-iron pipe, the taps should be staggered
around the circumference at least 12 in. (300 mm) apart (not in a straight line).
These restrictions do not apply to ductile-iron pipe. Furthermore, ductile-iron pipe in
all classes, including standard pressure-class pipe, may be directly tapped with
standard corporation stops; however, the torque requirement for the installation may
be effectively reduced by the application of two layers of 3-mil (0.1-mm) pipe-thread
sealant tape to the male threads of the corporation stop.
Service taps on gray-iron and ductile-iron mains encased in polyethylene may be
accomplished by making an X-shaped cut in the polyethylene and temporarily folding
back the film. After the tap has been completed, cuts in the polyethylene and any
other areas of damage to the film shall be repaired with tape as described in ANSI/
AWWA C105/A21.5. Direct service taps may also be made through the polyethylene,
with any resulting damaged areas being repaired as described previously. The
preferred method of making direct service taps consists of applying two or three
wraps of polyethylene adhesive tape completely around the pipe to cover the area
where the tapping machine and chain will be mounted. This method minimizes
possible damage to the polyethylene during the direct tapping procedure. After the
tapping machine is mounted, the corporation stop is installed directly through the
tape and polyethylene as shown in Figure 5. This method is very effective in
eliminating damage to the polyethylene encasement by the tapping machine and
chain during the tapping operation. After the direct tap is completed, the entire
circumferential area should be closely inspected for damage and repaired if needed.
Service lines of dissimilar metals also shall be wrapped with polyethylene or a
suitable dielectric tape for a minimum clear distance of 3 ft (0.9 m) away from the
gray-iron or ductile-iron main.
Sec. 4.7 Unloading, Handling, and Storage
All pipe, fittings, valves, hydrants, and accessories shall be loaded and unloaded
by lifting with lift hoists or skidding in order to avoid shock or damage. Under no
circumstances shall this material be dropped. Pipe handled on skidways shall not be
rolled or skidded against other pipe.
4.7.1 Unloading pipe. Trucks shall be parked on level ground for unloading.
Rail sidings are generally level enough for unloading purposes.
4.7.1.1 Before releasing the chains, cables, and strapping around the pipe, the
loads shall be checked to ensure that all chock blocks are securely in place on both
ends of all support timbers. If not, chocks or other suitable wedges shall be nailed
into position to prevent the pipe from rolling when the other restraints are removed.
Under no circumstances shall the chocks be removed while there is any possibility of
*In cold climates with deep frost penetration, freezing of service lines can be a problem. In
these localities, installing corporation stops horizontally at the three o’clock or nine o’clock
position on the pipe circumference will conserve available cover over the service line or reduce
the necessary depth that the main pipeline should be buried.

Figure 5 Preferred method for making direct service taps on polyethylene-encased iron pipe
pipe rolling out of control and causing damage or injury. Only after all chocks are in
place shall the chains or other binders securing the load to the truck or railcar be
released. Personnel shall never remain on, in front of, or alongside the load of pipe
after the restraints are removed.
4.7.1.2 Unloading shall be done by lifting with a fork truck, a crane, or other
suitable lifting device. Pipe shall never be rolled off the truck or railcar. When pipe is
being unloaded one at a time, or in single layers, the restraining bands or straps shall
be removed only from the layer being unloaded. Steel bands shall be cut with a long-
handled bolt cutter or similar tool. Do not cut the bands with an ax, chisel, or other
tool likely to cause product damage or personal injury. Personnel not directly involved
in the unloading operation shall stand clear. Never stand under a lifted load. Inspect,
repair, and replace lifting devices on a timely basis.
4.7.2 Padding. Slings, hooks, or pipe tongs shall be padded, and the padding
shall be used to prevent damage to the exterior surface or internal lining of the pipe,
fitting, or related product.
4.7.3 Storage. If stored, materials shall be kept safe from damage. The
interior of all pipe, fittings, and other appurtenances shall be kept free from dirt or
foreign matter at all times. Valves and hydrants shall be drained and stored in a
manner that will protect them from damage by freezing.
4.7.3.1 Pipe shall not be stacked higher than the limits shown in Table 5. The
bottom tier shall be kept off the ground on timbers, rails, or other suitable supports.
Pipe in tiers shall be alternated as follows: bell, plain end; bell, plain end. At least
two rows of timbers shall be placed between tiers, and chocks shall be affixed to each
timber in order to prevent movement. The timbers shall be large enough to prevent
contact between the pipe in adjacent tiers.
4.7.3.2 Gaskets shall be stored in a cool location, out of direct sunlight.
Gaskets shall not come in contact with petroleum products. Gaskets shall be used on
a first-in, first-out basis.
4.7.3.3 Mechanical-joint bolts shall be stored in a dry location and handled in
a manner that will ensure proper use with respect to types and sizes.
4.7.3.4 Prolonged exposure to sunlight will eventually deteriorate polyethylene
film. Therefore, exposure to sunlight prior to backfilling the wrapped pipe should be
kept to a minimum.

20 AWWA C600-99
Table 5 Maximum stacking heights—ductile-iron pipe*
Nominal Pipe Size Number of Tiers
in. (mm)
13 12,(76) 18
14 1,(102) 16
16 1,(152) 13
18 1,(203) 11
10 1,(254) 10
12 1,(305) 19
14 1,(356) 18
16 1,(406) 17
18 1,(457) 16
20 1,(508) 16
24 1,(610) 15
30 1,(762) 14
36 1,(914) 14
42 (1,067) 13
48 (1,219) 13
54 (1,400) 13
60 (1,500) 13
64 (1,600) 13
*For 18- or 20-ft (5.5- or 6.1-m) lengths.
SECTION 5: VERIFICATION
Sec. 5.1 Inspection
If stipulated in the specifications, all materials are subject to inspection and
approval at the manufacturer’s plant.
5.1.1 Inspection on delivery. All pipe and appurtenances are subject to
inspection on delivery. Neither inspection nor failure to provide inspection shall
relieve the manufacturer of the responsibility to provide materials meeting the
specifications. Material found to be defective because of manufacture or damage in
shipment shall be rejected or recorded on the bill of lading and removed from the
jobsite. Tests may be performed as specified in the applicable AWWA standard to
ensure conformance with the standard. Pipe or appurtenances that fail to comply
with specified tests shall be rejected.
5.1.2 Workmanship. All pipe and appurtenances shall be installed and joined
in conformance with this standard and tested under pressure for defects and leaks in
accordance with Sec. 5.2 of this standard.

Sec. 5.2 Hydrostatic Testing

WARNING: The testing methods described in this section are specific for
water-pressure testing. These procedures should not be applied for air-pressure testing
because of the serious safety hazards involved.
5.2.1 Pressure test.
5.2.1.1 Test restrictions. Test pressure shall not be less than 1.25 times the
working pressure at the highest point along the test section.
Test pressure shall not exceed pipe or thrust-restraint design pressures.
The hydrostatic test shall be of at least a 2-h duration.
Test pressure shall not vary by more than ±5 psi (34.5 kPa) for the duration of
the test.
Valves shall not be operated in either direction at a differential pressure
exceeding the rated valve working pressure. A test pressure greater than the rated
valve pressure can result in trapped test pressure between the gates of a double-disc
gate valve. For tests at these pressures, the test setup should include a provision,
independent of the valve, to reduce the line pressure to the rated valve pressure on
completion of the test. The valve can then be opened enough to equalize the trapped
pressure with the line pressure, or the valve can be fully opened if desired.
The test pressure shall not exceed the rated pressure of the valves when the
pressure boundary of the test section includes closed, resilient-seated gate valves or
butterfly valves.
5.2.1.2 Pressurization. After the pipe has been laid, all newly laid pipe or
any valved section thereof shall be subjected to a hydrostatic pressure of at least 1.5
times the working pressure at the point of testing. Each valved section of pipe shall
be slowly filled with water, and the specified test pressure (based on the elevation of
the lowest point of the line or section under test and corrected to the elevation of the
test gauge) shall be applied using a pump connected to the pipe. Valves shall not be
operated in either the opened or closed direction at differential pressures above the
rated pressure. The system should be allowed to stabilize at the test pressure before
conducting the hydrostatic test.
5.2.1.3 Air removal. Before applying the specified test pressure, air shall be
expelled completely from the section of piping under test. If permanent air vents are
not located at all high points, corporation cocks shall be installed at these points to
expel the air as the line is filled with water. After the air has been expelled, the
corporation cocks shall be closed and the test pressure applied. At the conclusion of
the pressure test, the corporation cocks shall be removed and the pipe plugged or left
in place as required by the specifications.
5.2.1.4 Examination. Any exposed pipe, fittings, valves, hydrants, and joints
shall be examined carefully during the test. Any damage or defective pipe, fittings,
valves, hydrants, or joints that are discovered following the pressure test shall be
repaired or replaced with reliable material, and the test shall be repeated until
satisfactory results are obtained.
5.2.1.5 Testing allowance defined. Testing allowance shall be defined as the
quantity of makeup water that must be supplied into the newly laid pipe or any
valved section thereof to maintain pressure within 5 psi (34.5 kPa) of the specified
test pressure after the pipe has been filled with water and the air has been
expelled. Testing allowance shall not be measured by a drop in pressure in a test
section over a period of time.
5.2.1.6 Testing allowance. No pipe installation will be accepted if the amount
of makeup water is greater than that determined by the following formula:

22 AWWA C600-99
In inch–pound units,
SD P -
L = -------------------- (Eq 1)
133, 200
Where:
L = testing allowance (makeup water), in gallons per hour
S = length of pipe tested, in feet
D = nominal diameter of the pipe, in inches
P = average test pressure during the hydrostatic test, in pounds per
square inch (gauge)
In metric units,
SD P
L m = --------------------- (Eq 2)
715, 317
Where:
Lm = testing allowance (makeup water), in liters per hour
S = length of pipe tested, in meters
D = nominal diameter of the pipe, in millimeters
P = average test pressure during the hydrostatic test, in kPa
These formulas are based on a testing allowance of 11.65 gpd/mi/in. (1.079 L/d/
km/mm) of nominal diameter at a pressure of 150 psi (1,034 kPa).
5.2.1.6.1 Testing allowance at various pressures is shown in Tables 6A and
6B.
5.2.1.6.2 When testing against closed metal-seated valves, an additional
testing allowance per closed valve of 0.0078 gal/h/in. (1.2 mL/h/mm) of nominal valve
size shall be allowed.
5.2.1.6.3 When hydrants are in the test section, the test shall be made against
the main valve in the hydrant.
5.2.1.7 Acceptance of installation. Acceptance shall be determined on the
basis of testing allowance. If any test of laid pipe discloses a testing allowance greater
than that specified in Sec. 5.2.1.6, repairs or replacements shall be accomplished in
accordance with the specifications.
5.2.1.7.1 All visible leaks are to be repaired regardless of the allowance used
for testing.

Table 6A Hydrostatic testing allowance per 1,000 ft of pipeline*—gph†
Avg. Test Nominal Pipe Diameter—in.

Pressure
psi 3 4 6 8 10 12 14 16 18 20 24 30 36 42 48 54 60 64
450 0.48 0.64 0.95 1.27 1.59 1.91 2.23 2.55 2.87 3.18 3.82 4.78 5.73 6.69 7.64 8.60 9.56 10.19
400 0.45 0.60 0.90 1.20 1.50 1.80 2.10 2.40 2.70 3.00 3.60 4.50 5.41 6.31 7.21 8.11 9.01 9.61
350 0.42 0.56 0.84 1.12 1.40 1.69 1.97 2.25 2.53 2.81 3.37 4.21 5.06 5.90 6.74 7.58 8.43 8.99
300 0.39 0.52 0.78 1.04 1.30 1.56 1.82 2.08 2.34 2.60 3.12 3.90 4.68 5.46 6.24 7.02 7.80 8.32
275 0.37 0.50 0.75 1.00 1.24 1.49 1.74 1.99 2.24 2.49 2.99 3.73 4.48 5.23 5.98 6.72 7.47 7.97
250 0.36 0.47 0.71 0.95 1.19 1.42 1.66 1.90 2.14 2.37 2.85 3.56 4.27 4.99 5.70 6.41 7.12 7.60
225 0.34 0.45 0.68 0.90 1.13 1.35 1.58 1.80 2.03 2.25 2.70 3.38 4.05 4.73 5.41 6.03 6.76 7.21
200 0.32 0.43 0.64 0.85 1.06 1.28 1.48 1.70 1.91 2.12 2.55 3.19 3.82 4.46 5.09 5.73 6.37 6.80
175 0.30 0.40 0.59 0.80 0.99 1.19 1.39 1.59 1.79 1.98 2.38 2.98 3.58 4.17 4.77 5.36 5.96 6.36
150 0.28 0.37 0.55 0.74 0.92 1.10 1.29 1.47 1.66 1.84 2.21 2.76 3.31 3.86 4.41 4.97 5.52 5.88
125 0.25 0.34 0.50 0.67 0.84 1.01 1.18 1.34 1.51 1.68 2.01 2.52 3.02 3.53 4.03 4.53 5.04 5.37
100 0.23 0.30 0.45 0.60 0.75 0.90 1.05 1.20 1.35 1.50 1.80 2.25 2.70 3.15 3.60 4.05 4.50 4.80
DUCTILE-IRON MAINS AND APPURTENANCES

*If the pipeline under test contains sections of various diameters, the testing allowance will be the sum of the testing allowance for each size.
†Calculated on the basis of Eq. 1.
23
Table 6B Hydrostatic testing allowance per 300 m of pipeline*—L/h†
24 AWWA C600-99
Avg. Test Nominal Pipe Diameter—mm
Pressure
KPa 76 102 152 203 254 305 356 406 457 508 610 762 914 1,067 1,219 1,400 1,500 1,600
3,000 1.84 2.30 3.45 4.59 5.74 6.89 8.04 9.19 10.34 11.49 13.78 17.23 20.67 22.97 27.57 32.16 34.46 36.75
2,800 1.78 2.22 3.33 4.44 5.55 6.66 7.77 8.88 9.99 11.10 13.32 16.64 19.97 22.19 26.63 31.07 33.29 35.51
2,600 1.71 2.14 3.21 4.28 5.35 6.42 7.48 8.55 9.62 10.69 12.83 16.04 19.25 21.39 25.66 29.94 32.08 34.22
2,400 1.64 2.05 3.08 4.11 5.14 6.16 7.19 8.22 9.25 10.27 12.33 15.41 18.49 20.55 24.66 28.76 30.82 32.87
2,200 1.57 1.97 2.95 3.93 4.92 5.90 6.88 7.87 8.85 9.84 11.80 14.75 17.70 19.67 23.61 27.54 29.51 31.47
2,000 1.50 1.88 2.81 3.75 4.69 5.63 6.56 7.50 8.44 9.38 11.25 14.07 16.88 18.76 22.51 26.26 28.13 30.01
1,800 1.42 1.78 2.67 3.56 4.45 5.34 6.23 7.12 8.01 8.90 10.68 13.35 16.01 17.79 21.35 24.91 26.69 28.47
1,600 1.34 1.68 2.52 3.36 4.19 5.03 5.87 6.71 7.55 8.39 10.07 12.58 15.10 16.78 20.13 23.49 25.16 26.84
1,400 1.26 1.57 2.35 3.14 3.92 4.71 5.49 6.28 7.06 7.85 9.42 11.77 14.12 15.69 18.83 21.97 23.54 25.11
1,200 1.16 1.45 2.18 2.91 3.63 4.36 5.08 5.81 6.54 7.26 8.72 10.90 13.08 14.53 17.43 20.34 21.79 23.25
1,000 1.06 1.33 1.99 2.65 3.32 3.98 4.64 5.30 5.97 6.63 7.96 9.95 11.94 13.26 15.91 18.57 19.89 21.22
1,800 0.95 1.19 1.78 2.37 2.97 3.56 4.15 4.74 5.34 5.93 7.12 8.90 10.68 11.86 14.23 16.61 17.79 18.98
1,600 0.82 1.03 1.54 2.05 2.57 3.08 3.60 4.11 4.62 5.14 6.16 7.70 9.25 10.27 12.33 14.38 15.41 16.44
*If the pipeline under test contains sections of various diameters, the testing allowance will be the sum of the testing allowance for each size.
†Calculated on the basis of Eq. 2.

SECTION 6: DELIVERY
There are no applicable requirements for this section.

1P-7.5M-43600-11/99-CM Printed on recycled paper.

Awwa C600-99

Uploaded by

Copyright:

Available Formats

Awwa C600-99

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Awwa C600-99

Uploaded by

Copyright:

Available Formats

American Water Works Association

Effective date: January 1, 2000.

AMERICAN WATER WORKS ASSOCIATION

Copyright © 1999 American Water Works Association, All Rights Reserved

American National Standard

Copyright © 1999 by American Water Works Association

Copyright © 1999 American Water Works Association, All Rights Reserved

Charles W. McCauley Jr., Chair

J.L. Doane, Portland Water Bureau, Portland, Ore. (AWWA)

General Interest Members

Edward T. Knudsen Jr., Chair

T.E. Coughran, City of Santa Ana, Santa Ana, Calif. (AWWA)

General Interest Members

K.M. Bell, Underwriters Laboratories Inc., Northbrook, Ill. (UL)

Copyright © 1999 American Water Works Association, All Rights Reserved

L.R. Dunn, US Pipe & Foundry Company, Birmingham, Ala. (DIPRA)

Copyright © 1999 American Water Works Association, All Rights Reserved

SEC. PAGE SEC. PAGE

Copyright © 1999 American Water Works Association, All Rights Reserved

Copyright © 1999 American Water Works Association, All Rights Reserved

Copyright © 1999 American Water Works Association, All Rights Reserved

Copyright © 1999 American Water Works Association, All Rights Reserved

Copyright © 1999 American Water Works Association, All Rights Reserved

Copyright © 1999 American Water Works Association, All Rights Reserved

AWWA STANDARD FOR

Copyright © 1999 American Water Works Association, All Rights Reserved

Sec. 1.3 Application

Copyright © 1999 American Water Works Association, All Rights Reserved

ANSI/AWWA C502—Standard for Dry-Barrel Fire Hydrants.

Copyright © 1999 American Water Works Association, All Rights Reserved

Sec. 4.2 Installing Ductile-Iron Mains

Copyright © 1999 American Water Works Association, All Rights Reserved

Table 1 Suggested trench widths at the top of the pipe

Nominal Pipe Size Trench Width

Copyright © 1999 American Water Works Association, All Rights Reserved

Copyright © 1999 American Water Works Association, All Rights Reserved

Copyright © 1999 American Water Works Association, All Rights Reserved

Figure 1 Laying conditions for ductile-iron pipe

Copyright © 1999 American Water Works Association, All Rights Reserved

3. Be sure that the plain end is beveled; square or sharp

4. Small pipe can be pushed into the bell socket with a

Figure 2 Push-on-joint assembly

Copyright © 1999 American Water Works Association, All Rights Reserved

1. Clean the socket and the plain end. Lubrication and

Figure 3 Mechanical-joint assembly

Copyright © 1999 American Water Works Association, All Rights Reserved

Table 2 Mechanical-joint bolt torque

Joint Size Bolt Size Range of Torque

30–36 (762–914) 111 (25) 100–120 (136–163)

42–48 (1,067–1,219) 11/4 (32) 120–150 (163–203)

Figure 4 Pipeline curve geometry

Copyright © 1999 American Water Works Association, All Rights Reserved

Table 3 Maximum joint deflection* full-length pipe—push-on-type joint pipe

Approx. Radius of Curve—R†

L†=18 ft L†=20 ft L†=18 ft L†=20 ft

Copyright © 1999 American Water Works Association, All Rights Reserved

Table 4 Maximum joint deflection full-length pipe—mechanical-joint pipe

Approx. Radius of Curve—R*

L*=18 ft L*=20 ft L*=18 ft L*=20 ft

L=18 ft L=20 ft L=18 ft L=20 ft