Part 2 Safe Operation and Use Method

A14JE Operation And Use Method
LINGONG HEAVY MACHINERY CO.，LTD.

CONTENTS
Part 1: Safe Operation And Use Method

Part 1.1: Safe Wearing
Operation
Repair
1) Be equipped with full-body protective equipment, such as safety helmet, safety belt, safety shoes, goggles,
protective gloves, and be in good physical condition.
2) Working environment: on firm level ground, far away from barrier and high-voltage wires, instantaneous
wind speed less than 12.5m/s.
3) Check before operation: Ensure that the manual is complete, all labels are clear, structural parts are free
from cracks and deformations, all connecting pins and screws are firm and not loose, all hydraulic valve
blocks and pipes are free from leakage, and electrical components and ropes are not damaged or loose.
Part 2.2: Pre-operation Inspection
1) Ensure that the manual is complete, easy to read and saved inside the file box of the platform . If you need to change the manual, please
contact the service personnel of LGMG.
2) Ensure that all labels are clear, easy to read and properly positioned. See the "Labeling" section. If you need to replace the label, please contact
the service personnel of LGMG.
3) Check whether the ball valve at the oil suction port at the bottom of the hydraulic tank is open, no special circumstances must be kept open,
and when the machine is working , it must be in the open state, if not open when the machine is in action. This valve may cause complete
damage to the oil pump.
4) Please refer to the "Maintenance" section to check whether the hydraulic oil is leakage and whether the oil level is appropriate.
5) Check whether the battery connection is firm.
6) Check whether the parts are damaged, improperly installed or part loose or missing parts and unauthorized changes
7) Check the whole machine for:
a)A crack in a weld or structural part
b) A dent or damage to a machine
c)Severe rusting, corrosion, or oxidation
d) Make sure all structural pieces and other key components are finished
e)All relevant fasteners and pins are in correct position and tighten
CONTENTS
Part 2 : Safe Operation

Part 2.1:Safe operation and use method-Emergency down(PG)
Ground control box Upper control box

Part 2.1:Safe operation and use method-Emergency down(COBO)
Ground control box Upper control box

Part 2.1:Safe operation and use method-Emergency power unit
If the main power fails, the auxiliary power should be used.

1) Turn the key to the ground or the upper control box.
2) Pull out the red "Emergency Stop" button to the "ON" position.
3) When operating the power unit (i.e., emergency pump) on the
platform, press the foot switch.
4) Enable the desired function while keeping the power unit (i.e.,
emergency pump) open.
5) The drive function may not work with the emergency power unit.

Part 2.2:Safe operation and use method-Driving on a slope
Determine the state of the articulating boom on slope, as shown below. Before moving the machine to the solid and horizontal
ground , lower the articulating boom per the following steps. Before lowering the boom, do not rotate the boom.
If the tilt alarm sounds on the up-slope of platform: If the tilt alarm sounds on the down-slope of platform:
1. Lower the primary boom. 2. Lower the secondary 1. Retract the primary boom.2. Lower the secondary
boom.3. Retract the primary boom. boom.3. Lower the primary boom.

Part 2.4:Safe operation and use method-Maximum Gradeability
Parameter
Item
A14JE/A14JE-Li
platform downhill: 30% (17°)
Platform uphill (climbing ability): 25% (14°)

Slope=Height ÷ length
3.6÷8=0.45=45%
Maximum slope rating 25% (14°) Angle=arctan(Slope value)
If the slope exceeds the maximum uphill , downhill or side slope rating, the machine must be lifted or transported
up and down the slope.

Part 2.5:Safe operation and use method-Anti-crash Protection Device
1. LED light
2.Override switch
3. Anti-collision rod
1. The platform anti-collision protection device is installed on the top of the platform control box. When the anti-
collision rod is removed from the proximity switch by external force, the machine will immediately stop all actions,
the LED lights will blink, and the buzzer will sound.
2. If need to operate the machine again, you need to reset the anti-collision or long press the override switch.

Part 2.6:Safe operation and use method-Fixed type
1.Turntable rotating lock pin 2.Fixed chassis 3. Fixed platform
1. Before the machine is transported, the turntable should be locked with the turntable rotation lock pin; (Figure 1)
2. Fully lower and retract the boom and remove any loose parts from the machine.
3. Fix the chassis: ensure that the chain or belt has sufficient load strength, and use at least 5 chains; (Figure 2)
4. Fix the platform: Put the sleeper under the platform rotating joint, do not let the sleeper touch the platform cylinder.
Secure the platform by threading the nylon (Figure 3, two ways).

Part 2.7:Safe operation and use method-Lifting Instructions
Mode X axis(mm) Y axis(mm)
A14JE 924 972

A14JE-Li 924 972
Center of gravity position (no load)

Lifting instructions
1) Lower and telescope the boom completely . Lower the jib boom completely. X-axis: horizontal distance from the
Remove any loose parts from the vehicle. center of the rear wheel to the center
2) Determine the center of gravity of the machine with the help of the picture below. of gravity;
3) Only connect the sling to the specified lifting point on the machine. There are Y-axis: vertical distance from the
four lifting points on the chassis. horizontal ground to the center of
4) Adjust the sling to avoid any damage to the vehicle and keep the vehicle in a gravity;
level position.
CONTENTS
Part 4: COBO Control System Use Method

Part 4:Upper control box(COBO Control System)

Part 4:Ground control box(COBO Control System)

Part 4:Upper control box operation(COBO)
5. Push
joystick
forward or
backward
1.Release 2. Key turn left 3. Release 4. Stepping

Emergency stop to upper control Emergency stop foot switch
button(ground) button(ground)
5. Push action
toggle
NOTE: When step foot switch without any action in 20s,there will be alarm and can’t do any action.

Part 4:Ground control box operation(COBO)
1.Release 2. Release 3. Key turn 4. Push 5. Push action

Emergency stop Emergency stop right to ground enable toggle
button(platform) button(ground) control button
NOTE: When step foot switch without any action in 20s,there will be alarm and can’t do any action.

Part 4: COBO Control System Operation
4.1 The boot interface display
Level NO. Main menu
1 I/O Enter into I/O diagnostic page
2 SET Enter into setting menu page
3 Motor Enter into motor information page
4 Parameter Enter into parameter setting page

Enter into Alarm and warning
5 Alarm Info
information page
1) The main interface displays information such as model, basket load, X/Y axis tilt angle, working hours, alarm code,
warning code, ZAPI controller code and SOC.
2) The 5 buttons at the bottom of the screen correspond to I/O, SET, MOTOR, PARAMETER and Alarm Info, press any
key to enter the corresponding interface.
LINGONG HEAVY MACHINERY CO.，LTD. 19
4.2 I/O
I/O
Level NO. elements
2 Chassis ECU
2 Cage ECU
2 MCU
2 BMS
To display the I/O menu contents,

Press the leftmost button
press the second key to select
It can scroll up and down to show different pages by  and  key at any I/O pins diagnostic page, Press , it can return
to main page, press ESC key, it can return to previous menu page.
4.2.1 I/O-Chassis ECU
Press and  to show all parameters of chassis ECU , Press to return to main page, press ESC to return to previous
menu page.
4.2.2 I/O-Cage ECU
Press and  to show all parameters of chassis ECU , Press to return to main page, press ESC to return to previous
menu page.
4.2.3 I/O-MCU
MCU
Level NO. content
3 Pump Motor PWM
3 Pump Motor Current
3 Drive Motor Current
3 Drive Motor Speed
Press  to select "MCU", and then press to check all items of MCU.

4.2.4 I/O-BMS
BMS
Level NO. content Level NO. content
3 Highest Sig Vol 3 Total Bat V
3 Lowest Sig Vol 3 Total Bat C
3 Heat Rly Sta 3 Highest Temp

Charge_
3 3 Lowest Temp
cyclenum
3 Soc 3 Discharge Cycle
3 Soh 3 Bms System F

4.3 SET
SET
Level NO. content
2 Basic Parameter
2 Advanced Parameter
2 Parameter Saving
2 History Alarm
2 Software Version
Press  and  to move cursor up and down, Press , it will return to main page, press ESC button, it will return to
previous menu page. Press to enter the selection with password 1542.

4.3.1 Basic Parameter
Basic Parameter
Level NO. content
3 Load cell Calibration
3 Parameter Set
3 Tilt sensor Calibration
3 Buzzer Mode
Press  and  to move cursor up and down, Press , it will return to main page, press ESC button, it will return to
previous menu page. Press to enter the selection with password 1542.

4.3.1 Basic Parameter-Load Cell Calibration
Load Cell Calibration
Level NO. content
4 Load Cell Zero Set
4 Load Cell Load Set
4 Input Actual Load
4 Actual Load

4.3.3 Basic Parameter-Parameter Set
Basic Parameter
Level Level
content content
NO. NO.
Main Boom
3 3 Cage Rotation
Amplitude
3 Main Boom Tel 3 Cage Level
Lower Boom
3 3 Turret Rotation
Amplitude
3 Jib Amplitude 3 Steer
3 Jib ROT 3
It can scroll up and down to show different pages by  and , Press , it can return to main page, press ESC key, it can
return to previous menu page.
4.3.3 Basic Parameter-Parameter Set-Main boom Amplitude
It can scroll up and down to show different pages by  and  to select any item, Press to enter “parameter set” page，
and then press  and  to input parameter , and then press to save parameter . Finally, press ESC to go back
previous menu page.

4.3.4 Basic Parameter-Tilt Sensor Calibration

4.3.5 Basic Parameter-Buzzer Mode

4.4 SET-Advanced Parameter
Press  and  to select “Advanced Parameter”, Press to enter “Input Password”page，press  and  to input
password 5244 then can check secondary menu , then press  to make scroll down to select any item , and then press
enter parameter set page.

4.4 SET-Advanced Parameter
Level NO. content
3 Set Language
3 Boom Combined Fu
3 Motor Speed Setting
3 Max Load
3 Set time
3 Sensor Detection
3 Level Model
3 Cumulative Time
3 Battery Type
3 Model Sel

4.4.1 Advanced Parameter-Set Language

4.4.2 Advanced Parameter-Boom Combined Fu

4.4.3 Advanced Parameter-Motor Speed Setting

4.4.4 Advanced Parameter-Max Load

4.4.5 Advanced Parameter-Set time

4.4.6 Advanced Parameter-Sensor Detection

4.4.7 Advanced Parameter-Level Model

4.4.8 Advanced Parameter-Cumulative Time

4.4.9 Advanced Parameter-Battery Type

4.4.10 Advanced Parameter-Model Set

4.5 SET-Parameter Saving

4.6 SET-History Alarm

4.7 SET-Software Version

4.8 Motor
LINGONG HEAVY MACHINERY CO.，LTD. 47

Thank You

Part 2 Safe Operation and Use Method

Uploaded by

Copyright:

Available Formats

Part 2 Safe Operation and Use Method

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Part 2 Safe Operation and Use Method

Uploaded by

Copyright:

Available Formats

A14JE Operation And Use Method

LINGONG HEAVY MACHINERY CO.，LTD.

Part 1: Safe Operation And Use Method

LINGONG HEAVY MACHINERY CO.，LTD.