SG30 33 40 50CX-UEN-Ver21-202211 PDF

User Manual
PV Grid-Connected Inverter
SG30CX / SG33CX / SG40CX / SG50CX / SG30CX-NI /
SG50CX-NI
SG30CX /
SG33CX / SG40CX / SG50CX /
SG30CX-NI / SG50CX-NIPV Grid-
Connected InverterUser
ManualSG30_33_40_50CX/SG30_
50CX-NI-UEN-Ver21-202211
SG30_33_40_50CX/SG30_50CX-NI-UEN-Ver21-202211
All Rights Reserved
All Rights Reserved

No part of this document can be reproduced in any form or by any means without the prior
written permission of Sungrow Power Supply Co., Ltd (hereinafter "SUNGROW").
Trademarks
and other Sungrow trademarks used in this manual are owned by
SUNGROW.
All other trademarks or registered trademarks mentioned in this manual are owned by their
respective owners.
Software Licenses
• It is prohibited to use data contained in firmware or software developed by SUNGROW,

in part or in full, for commercial purposes by any means.
• It is prohibited to perform reverse engineering, cracking, or any other operations that

compromise the original program design of the software developed by SUNGROW.
I
About This Manual
The manual mainly contains the product information, as well as guidelines for installation,
operation, and maintenance. The manual does not include complete information about the
photovoltaic (PV) system. Readers can get additional information at www.sungrowpower.
com or on the webpage of the respective component manufacturer.
Validity
This manual is valid for the following model of low-power grid-connected PV string inverters:
• SG30CX
• SG33CX
• SG40CX
• SG50CX
• SG30CX-NI
• SG50CX-NI
It will be referred to as "inverter" hereinafter unless otherwise specified.

Target Group
This manual is intended for professional technicians who are responsible for installation, op-
eration, and maintenance of inverters, and users who need to check inverter parameters.
The inverter must only be installed by professional technicians. The professional technician
is required to meet the following requirements:
• Know electronic, electrical wiring and mechanical expertise, and be familiar with electri-
cal and mechanical schematics.
• Have received professional training related to the installation and commissioning of elec-
trical equipment.
• Be able to quickly respond to hazards or emergencies that occur during installation and
commissioning.
• Be familiar with local standards and relevant safety regulations of electrical systems.
• Read this manual thoroughly and understand the safety instructions related to
operations.
How to Use This Manual
Please read this manual carefully before using the product and keep it properly at a place
for easy access.
All contents, pictures, marks, and symbols in this manual are owned by SUNGROW. No part
of this document may be reprinted by the non-internal staff of SUNGROW without written
authorization.
II
Contents of this manual may be periodically updated or revised, and the actual product pur-
chased shall prevail. Users can obtain the latest manual from support.sungrowpower.com
or sales channels.
Symbols
This manual contains important safety instructions, which are highlighted with the following
symbols, to ensure personal and property safety during usage, or to help optimize the prod-
uct performance in an efficient way.
Please carefully understand the meaning of these warning symbols to better use the manual.
Indicates high-risk potential hazards that, if not avoided, may lead to death or seri-
ous injury.
Indicates moderate-risk potential hazards that, if not avoided, may lead to death or
serious injury.
Indicates low-risk potential hazards that, if not avoided, may lead to minor or mod-
erate injury.
Indicates potential risks that, if not avoided, may lead to device malfunctions or fi-
nancial losses.
“NOTE” indicates additional information, emphasized contents or tips that may be

helpful, e.g., to help you solve problems or save time.
III
Contents
All Rights Reserved .....................................................................................................I
About This Manual......................................................................................................II
1 Safety Instructions ............................................................................................1
1.1 Unpacking and Inspection ...............................................................................1
1.2 Installation Safety ...........................................................................................2
1.3 Electrical Connection Safety............................................................................2
1.4 Operation Safety ............................................................................................4
1.5 Maintenance Safety ........................................................................................4
1.6 Disposal Safety ..............................................................................................5
2 Product Description ..........................................................................................6
2.1 System Introduction ........................................................................................6
2.2 Product Introduction........................................................................................7
2.3 Symbols on Product........................................................................................9
2.4 LED Indicator .................................................................................................9
2.5 DC Switch....................................................................................................10
2.6 Circuit Diagram ............................................................................................ 11
2.7 Function Description .....................................................................................12
3 Unpacking and Storage .................................................................................14
3.1 Unpacking and Inspection .............................................................................14
3.2 Inverter Storage ...........................................................................................14
4 Mechanical Mounting .....................................................................................16
4.1 Safety During Mounting.................................................................................16
4.2 Location Requirements .................................................................................16
4.2.1 Environment Requirements..................................................................17
4.2.2 Carrier Requirements ..........................................................................17
4.2.3 Angle Requirements............................................................................18
4.2.4 Clearance Requirements .....................................................................19
4.3 Installation Tools...........................................................................................20
4.4 Moving the Inverter .......................................................................................22
4.4.1 Manual Transport ................................................................................22
4.4.2 Hoisting Transport...............................................................................22
V
4.5 Installing Mounting-bracket............................................................................24
4.5.1 PV Bracket-Mounted Installation ..........................................................24
4.5.2 Wall-Mounted Installation.....................................................................25
4.6 Installing the Inverter.....................................................................................26
5 Electrical Connection .....................................................................................28
5.1 Safety Instructions ........................................................................................28
5.2 Terminal Description .....................................................................................29
5.3 Electrical Connection Overview .....................................................................30
5.4 Crimp OT/DT terminal ...................................................................................32
5.5 External Protective Grounding Connection .....................................................33
5.5.1 External Protective Grounding Requirements ........................................33
5.5.2 Connection Procedure.........................................................................33
5.6 AC Cable Connection ...................................................................................34
5.6.1 AC Side Requirements ........................................................................34
5.6.2 Requirements for OT/DT Terminal ........................................................36
5.6.3 Connection Procedure.........................................................................36
5.7 DC Cable Connection ...................................................................................39
5.7.1 PV Input Configuration ........................................................................40
5.7.2 Assembling PV Connectors .................................................................41
5.7.3 Installing PV Connector .......................................................................42
5.8 Communication Junction Box ........................................................................43
5.9 Communication Wiring Board ........................................................................44
5.10 RS485 Connection......................................................................................44
5.10.1 Interface Description .........................................................................44
5.10.2 RS485 Communication System ..........................................................45
5.10.3 Connection Procedure(Terminal Block) ...............................................47
5.10.4 Connection Procedure (RJ45 Ethernet Port)........................................48
5.11 Dry Contact Connection ..............................................................................50
5.11.1 Dry Contact Function .........................................................................50
5.11.2 Wiring Procedure...............................................................................52
5.12 DRM Connection（For Countries “AU” and “NZ”）........................................52
5.12.1 DRM Function...................................................................................52
5.12.2 Connection Procedure .......................................................................53
5.13 Communication Module Connection (optional) ..............................................55
6 Commissioning ...............................................................................................56
6.1 Inspection Before Commissioning..................................................................56
VI
6.2 Commissioning Procedure ............................................................................56
7 iSolarCloud App ..............................................................................................57
7.1 Brief Introduction ..........................................................................................57
7.2 Installing App ...............................................................................................57
7.3 Function Overview........................................................................................58
7.4 Login ...........................................................................................................58
7.4.1 Requirements .....................................................................................58
7.4.2 Login Procedure .................................................................................58
7.5 Home ..........................................................................................................62
7.6 Run Information............................................................................................64
7.7 Records .......................................................................................................66
7.8 More............................................................................................................68
7.8.1 System Parameters.............................................................................68
7.8.2 Operation Parameters .........................................................................69
7.8.3 Power Regulation Parameters..............................................................71
7.8.4 Communication Parameters.................................................................76
7.8.5 Firmware Update ................................................................................76
7.8.6 Password Changing ............................................................................77
8 System Decommissioning ............................................................................79
8.1 Disconnecting Inverter ..................................................................................79
8.2 Dismantling the Inverter ................................................................................79
8.3 Disposal of Inverter.......................................................................................80
9 Troubleshooting and Maintenance ..............................................................81
9.1 Troubleshooting ...........................................................................................81
9.2 Maintenance ................................................................................................89
9.2.1 Maintenance Notices...........................................................................89
9.2.2 Routine Maintenance ..........................................................................90
9.2.3 Cleaning Air Inlet and Outlet.................................................................91
9.2.4 Fan Maintenance ................................................................................91
10 Appendix .......................................................................................................93
10.1 Technical Data............................................................................................93
10.2 Wring Distance of DI Dry Contact.................................................................99
10.3 Quality Assurance .................................................................................... 101
10.4 Contact Information .................................................................................. 101
VII
1 Safety Instructions
When installing, commissioning, operating, and maintaining the product, strictly observe the
labels on the product and the safety requirements in the manual. Incorrect operation or work
may cause:
• Injury or death to the operator or a third party.
• Damage to the product and other properties.
• The safety instructions in this manual are only supplements and cannot cover
all the precautions that should be followed. Perform operations considering ac-
tual onsite conditions.
• SUNGROW shall not be held liable for any damage caused by violation of gen-
eral safety operation requirements, general safety standards, or any safety in-
struction in this manual.
• When installing, operating, and maintaining the product, comply with local laws
and regulations. The safety precautions in this manual are only supplements
to local laws and regulations.
1.1 Unpacking and Inspection
Check all safety signs, warning labels and nameplates on devices.

The safety signs, warning labels and nameplates must be clearly visible and can-
not be removed or covered before the device is decommissioned.
After receiving the product, check whether the appearance and structural parts of
the device are damaged, and check whether the packing list is consistent with the
actual ordered product. If there are problems with the above inspection items, do
not install the device and contact your distributor first. If the problem persists, con-
tact SUNGROW in time.
1
1 Safety Instructions User Manual
1.2 Installation Safety
Make sure there is no electrical connection before installation.

Before drilling, avoid the water and electricity wiring in the wall.
Improper installation may cause personal injury!
• If the product supports hoisting transport and is hoisted by hoisting tools, no

one is allowed to stay under the product.
• When moving the product, be aware of the product weight and keep the balance
to prevent it from tilting or falling.
Before operating the product, must check and ensure that tools to be used have
been maintained regularly.
1.3 Electrical Connection Safety
Before electrical connections, please make sure that the inverter is not damaged,
otherwise it may cause danger!
Before electrical connections, please make sure that the inverter switch and all
switches connected to the inverter are set to "OFF", otherwise electric shock may
occur!
The PV string will generate lethal high voltage when exposed to sunlight.
• Operators must wear proper personal protective equipment during electrical

connections.
• Must ensure that cables are voltage-free with a measuring instrument before
touching DC cables.
• Respect all safety instructions listed in relevant documents about PV strings.
• The inverter must not be connected to a PV string that requires positive or neg-
ative grounding.
2
User Manual 1 Safety Instructions
Danger to life due to a high voltage inside the inverter!
• Be sure to use special insulation tools during cable connections.
• Note and observe the warning labels on the product, and perform operations
strictly following the safety instructions.
• Respect all safety instructions listed in this manual and other pertinent
documents.
Damage to the product caused by incorrect wiring is not covered by the warranty.
• Electrical connection must be performed by professionals.
• All cables used in the PV generation system must be firmly attached, properly
insulated, and adequately dimensioned.
Check the positive and negative polarity of the PV strings, and connect the PV con-
nectors to corresponding terminals only after ensuring polarity correctness.
During the installation and operation of the inverter, please ensure that the positive
or negative poles of PV strings do not short-circuit to the ground. Otherwise, an
AC or DC short-circuit may occur, resulting in equipment damage. The damage
caused by this is not covered by the warranty.
Comply with the safety instructions related to PV strings and the regulations re-
lated to the local grid.
3
1 Safety Instructions User Manual
1.4 Operation Safety
Please comply with the following requirements when the product is running:
• Do not touch its enclosure.
• It is strictly forbidden to plug and unplug any connector on the inverter.
• Do not touch any wiring terminal of the inverter. Otherwise, electric shock may
occur.
• Do not disassemble any parts of the inverter. Otherwise, electric shock may
occur.
• It is strictly forbidden to touch any hot parts of the inverter (such as the heat
sink). Otherwise, it may cause burns.
• Do not operate the DC switch if the inverter is equipped with the DC switch. Oth-
erwise, device damage or personal injury may occur.
1.5 Maintenance Safety
Risk of inverter damage or personal injury due to incorrect service!
• Before any service work, first disconnect the grid-side AC circuit breaker and
check the inverter status. If the inverter indicator is off, please wait until night to
disconnect the DC switch. If the inverter indicator is on, directly disconnect the
DC switch.
• After the inverter is powered off for 5 minutes, measure the voltage and current
with professional instrument. Only when there is no voltage nor current can op-
erators who wear protective equipment operate and maintain the inverter.
• Even if the inverter is shut down, it may still be hot and cause burns. Wear pro-
tective gloves before operating the inverter after it cools down.
Touching the power grid or the contact points and terminals on the inverter con-
nected to the power grid may lead to electric shock!
• The power grid side may generate voltage. Always use a standard voltmeter to
ensure that there is no voltage before touching.
To prevent misuse or accidents caused by unrelated personnel, post prominent

warning signs or demarcate safety warning areas around the product.
4
User Manual 1 Safety Instructions
To avoid the risk of electric shock, do not perform any other maintenance opera-
tions beyond those described in this manual. If necessary, contact your distributor
first. If the problem persists, contact SUNGROW. Otherwise, the losses caused is
not covered by the warranty.
1.6 Disposal Safety
Please scrap the product in accordance with relevant local regulations and stand-
ards to avoid property losses or casualties.
5
2 Product Description
2.1 System Introduction
The inverter is a transformerless 3-phase PV grid-connected inverter. As an integral compo-

nent in the PV power system, the inverter is designed to convert the direct current power
generated from the PV modules into grid-compatible AC current and to feed the AC current
into the utility grid.
The intended usage of the inverter is illustrated in the following figure.
figure 2-1 Inverter Application in PV Power System
The inverter must not be connected to a PV string that requires positive or negative
grounding.
Do not connect any local load between the inverter and the AC circuit breaker.
The inverter applies only to the scenarios described in this manual.
Item Description Note

Monocrystalline silicon, polycrystalline silicon and thin-film
A PV strings
without grounding.
SG30CX, SG33CX, SG40CX, SG50CX, SG30CX-NI,
B Inverter
SG50CX-NI.
Grid connection Includes devices such as AC circuit breaker, SPD, metering
C
cabinet device.
Boost the low voltage from the inverter to grid-compatible me-
D Transformer
dium voltage.
E Utility grid TN-C, TN-S, TN-C-S, TT, IT.
The following figure shows the common grid configurations.
6
User Manual 2 Product Description
2.2 Product Introduction

Model Description
The model description is as follows(Take SG30CX as an example) :
Appearance
The following figure shows the appearance of the inverter. The image shown here is for
reference only. The actual product received may differ.
7
2 Product Description User Manual
figure 2-2 Inverter Appearance
No. Name Description

1 LED indicator To indicate the current working state of the inverter.
2 Mounting lugs To hang the inverter onto the mounting-bracket.
3 Side handles To move the inverter.
4 Labels Warning symbols, nameplate, and QR code.
External protective
5 grounding Use to ground the inverter.
terminals
6 Bottom handles To move the inverter.
7 DC switches To disconnect the DC current safely.
AC terminals,DC terminals, and communication terminals.
8 Wiring area
For details, refer to"5.2 Terminal Description"
Dimensions
The following figure shows the dimensions of the inverter.
figure 2-3 Product Dimensions(in mm)
*The image shown here is for reference only. The actual product you receive may differ.
8
Type Dimensions (W*H*D) Weight

SG30CX
SG30CX-NI 702×595×310 mm 50 kg
SG33CX
SG40CX 58 kg
SG50CX 782×645×310 mm 62 kg
SG50CX-NI 62 kg
2.3 Symbols on Product
Symbol Explanation
Do not dispose of the inverter together with household waste.
TÜV mark of conformity.
CE mark of conformity.
EU/EEA Importer.
Regulatory compliance mark.
The inverter does not have a transformer.
CGC-SOLAR mark of conformity.
Danger to life due to high voltages!

Only qualified personnel can open and service the inverter.
Disconnect the inverter from all the external power sources before
maintenance!
Burn danger due to the hot surface that may exceed 60°C.
Do not touch live parts for 5 minutes after disconnection from the power
sources.
Read the user manual before maintenance!
* The table shown here is for reference only. The actual product received may differ.
2.4 LED Indicator
The LED indicator on the front of the inverter indicates the working state of the inverter.
9
table 2-1 LED Indicator State Description
LED Color State Definition

The device is connected to the grid and operating
On
normally.
Fast blink The Bluetooth connection is established, and there is
(Period: 0.2s) data communication.
No system fault occurs.
Slow blink
Blue The device is in standby or startup state (not feeding
(Period: 2s)
power into the grid).
A fault occurs and the device cannot connect to the

On
grid.
The Bluetooth connection is established, data commu-

Blink
nication in process, and a system fault occurs.
Red
OFF Both the AC and DC sides are powered down.
Gray
Voltage may still be present in AC side circuits after the indicator is off. Pay atten-
tion to the electricity safety when operating.
2.5 DC Switch
The DC switch is used to disconnect the DC current safely whenever necessary.

The SG30CX-NI and SG50CX-NI is not equipped with DC switch.
The SG30CX and SG33CX is equipped with one DC switch to control the connection and
disconnection of all DC terminals.
The SG40CX and SG50CX are equipped with two DC switches separately controlling a
group of DC inputs. The correspondence is as follows:
10
* The image shown here is for reference only. The actual product received may differ.
Turn the DC switches to the ON position before restarting the inverter.
2.6 Circuit Diagram
The following figure shows the main circuit of the inverter.
figure 2-4 Circuit Diagram
• The DC SPD provides a discharge circuit for the DC side overvoltage to prevent it from
damaging the internal circuits of the inverter.
• EMI filters can filter out the electromagnetic interference inside the inverter to ensure that
the inverter meets the requirements of electromagnetic compatibility standards.
• The MPPT is used to ensure a maximum power from PV arrays at different PV input
conditions.
• The Inverter Circuit converts the DC power into grid-compliant AC power and feeds it into
the grid.
• The AC filter filters the output AC component of high frequency to ensure that the output
current meets the grid requirements.
• The AC relay isolates the AC output of the inverter from the grid, making the inverter safe
from the grid in case of inverter failure or grid failure.
• The AC SPD provides a discharge circuit for the AC side overvoltage to prevent it from
damaging the internal circuits of the inverter.
11
2.7 Function Description
The inverter is equipped with the following functions:

Conversion Function
The inverter converts the DC current into grid-compatible AC current and feeds the AC cur-
rent into the grid.
Data Storage
The inverter logs running information, error records, etc.
Parameter Configuration
The inverter provides various settable parameters. Users can set parameters via the App to
meet the requirements and optimize the performance.
Communication Interface
The inverter is designed with standard RS485 communication interfaces and communication
accessory port.
The standard RS485 communication interfaces are used to establish communication con-
nection with monitoring devices and upload monitoring data by using communication cables.
The communication accessory port is used to connect communication module manufactured
by SUNGROW, and upload monitoring data by means of wireless communication.
The inverter can be connected to communication devices via either of the two interfaces.
After communication connection is established, users can view inverter information or set in-
verter parameters through the iSolarCloud.
It is recommended to use the communication module from SUNGROW. Using a

device from other companies may lead to communication failure or other unex-
pected damage.
The inverter can provide export control but will require the use of a external smart meter.
The export control functionality has not been tested to AS/NZS 4777.2:2020.
Protection Function
The protective functions are integrated in the inverter, including anti-island protection, LVRT/
ZVRT, DC reversed polarity protection, AC short circuit protection, leakage current protec-
tion, DC overvoltage/overcurrent protection, etc.
PID recovery
The PID effect (Potential Induced Degradation) of PV modules will cause serious damage to
generated output and yield, which can be avoided or recovered by PID recovery function.
• For positive voltage scheme, after the PID is enabled, the voltage to ground of all PV
strings is greater than 0, and therefore the PV string-to-ground voltage is a positive value.
12
• For negative voltage scheme, after the PID is enabled, the voltage to ground of all PV
strings is lower than 0, and therefore the PV string-to-ground voltage is a negative value.
• Before enabling the PID recovery function, make sure the voltage polarity of the
PV modules to ground meets requirement. If there are any questions, contact
the PV module manufacturer or read the corresponding user manual.
• PID recovery function and Q at night cannot be enabled at the same time.
• If the voltage scheme for the PID protection/recovery function does not meet
the requirement of corresponding PV modules, the PID will not work as ex-
pected or even damage the PV modules.
• If the PID recovery function is enabled, it only works at night.
• After the PID recovery function is enabled, the voltage of the PV string to
ground is 500Vdc by default, and the default value can be modified through the
App.
AFCI Function(Optional)
• AFCI activation
This function can be enabled to detect whether arc occurs in the DC circuit of the inverter.
• AFCI self-test
This function is intended to detect whether the AFCI function of the inverter is normal.
13
3 Unpacking and Storage
3.1 Unpacking and Inspection
The product is thoroughly tested and strictly inspected before delivery. Nonetheless, dam-
age may still occur during shipping. For this reason, please conduct a thorough inspection
after receiving the product.
• Check the packing case for any visible damage.
• Check the scope of delivery for completeness according to the packing list.
• Check the inner contents for damage after unpacking.
Contact SUNGROW or the transport company in case of any damage or incompleteness,

and provide photos to facilitate services.
Do not dispose of the original packing case. It is recommended to store the device in the
original packing case when the product is decommissioned.
After receiving the product, check whether the appearance and structural parts of
the device are damaged, and check whether the packing list is consistent with the
actual ordered product. If there are problems with the above inspection items, do
not install the device and contact your distributor first. If the problem persists, con-
tact SUNGROW in time.
If any tool is used for unpacking, be careful not to damage the product.
3.2 Inverter Storage
Proper storage is required if the inverter is not installed immediately.
• Store the inverter in the original packing case with the desiccant inside.
• The storage temperature must be always between -40℃ and +70℃, and the storage rel-
ative humidity must be always between 0 and 95 %, non-condensing.
• In case of stacking storage, the number of stacking layers should never exceed the limit
marked on the outer side of the packing case.
• The packing case should be upright.
• If the inverter needs to be transported again, pack it strictly before loading and transport-
ing it.
14
User Manual 3 Unpacking and Storage
• Do not store the inverter in places susceptible to direct sunlight, rain, and strong electric
field.
• Do not place the inverter in places with items that may affect or damage the inverter.
• Store the inverter in a clean and dry place to prevent dust and water vapor from eroding.
• Do not store the inverter in places with corrosive substances or susceptible to rodents
and insects.
• Carry out periodic inspections. Inspection shall be conducted at least once every six
months. If any insect or rodent bites are found, replace the packaging materials in time.
• If the inverter has been stored for more than a year, inspection and testing by professio-
nals are required before it can be put into operation.
Please store the inverter according to the storage requirements. Product damage
caused by failure to meet the storage requirements is not covered by the warranty.
15
4 Mechanical Mounting
Respect all local standards and requirements during mechanical installation.
4.1 Safety During Mounting
Make sure there is no electrical connection before installation.

Before drilling, avoid the water and electricity wiring in the wall.
Poor installation environment will affect system performance!
• Install the inverter in a well-ventilated place.
• Ensure that the heat dissipation system or vent is not blocked.
• Do not install the inverter in an environment with flammable and explosive ob-
jects or smoke.
Improper handling may cause personal injury!
• When moving the inverter, be aware of its weight and keep the balance to pre-
vent it from tilting or falling.
• Wear proper protective equipment before performing operations on the inverter.
• The bottom terminals and interfaces of the inverter cannot directly contact the
ground or other supports. The inverter cannot be directly placed on the ground.
4.2 Location Requirements
To a large extent, a proper installation location ensures safe operation, service life, and per-
formance of the inverter.
• The inverter with protection rating IP66 can be installed both indoors and outdoors.
• The inverter should be installed at a height that allows easy viewing of the LED indicator
panel, as well as easy electrical connection, operation and maintenance.
16
User Manual 4 Mechanical Mounting
4.2.1 Environment Requirements

• The installation environment must be free of inflammable or explosive materials.
• The location should not be accessible to children.
• The ambient temperature and relative humidity must meet the following requirements.
• Do not install the inverter outdoors in areas with high salinity, which mainly refer to the
areas within 500 m away from the coast. The deposition of salt fog varies largely with
nearby seawater characteristics, sea wind, precipitation, relative humidity, terrain, and
forest coverage.
• Inverters free from direct sunlight, direct rain and snow have longer service life. Consider
sheltered places as the installation location.
• The inverter should be well ventilated. Ensure air circulation.
• The inverter generates noise during operation and is not recommended to be installed in
living areas.
4.2.2 Carrier Requirements
The mounting structure where the inverter is installed must comply with local/national stand-
ards and guidelines. Ensure that the installation surface is solid enough to bear four times
the weight of the inverter and is suitable for the dimensions of the inverter (e.g. cement walls,
plasterboard walls, etc.).
17
4 Mechanical Mounting User Manual
4.2.3 Angle Requirements
Install the inverter vertically or at the maximum allowable rear tilt angle. Do not install the in-
verter horizontally, forward, excessively backward, sideways, or upside down.
Inverters in floating plants cannot be installed at a back tilt.
In case the installation site is a level surface, mount the inverter to the bracket to
meet the mounting angle requirements, as shown in the figure below.
Take the following items into account when designing the bracket scheme:
• Consider onsite climate conditions and take anti-snow and anti-rain measures
if necessary.
• Ensure that the waterproof connectors are at least 300mm higher than the
ground surface.
• Bind the cables at the positions 300~350mm away from the DC connector, AC
waterproof terminal, and communication waterproof terminal.
• The various waterproof terminals should be tightened with the torque specified
in this manual to ensure that they are securely sealed.
18
4.2.4 Clearance Requirements
Reserve enough clearance around the inverter to ensure sufficient space for heat
dissipation.
* In case this distance is less than the distance in the diagram, move the inverter from the
mounting-bracket or wall before maintaining fans.
The distance between the bottom of the inverter and the ground surface is deter-
mined according to the bending radius of the AC cable used and the installation
environment. In addition, the following conditions must be met:
• The distance between the bottom of the inverter and the ground surface is not
less 650 mm.
• The AC cable is vertically led into the cabinet, and the straight length is higher
than 200mm.
• If there are any questions, please consult the AC cable manufacturer.
19
In case of multiple inverters, reserve specific clearance between the inverters. For other in-
stallation scenarios, please refer to the relevant technical documents on http://support.sun-
growpower.com/.
In case of back-to-back installation, reserve specific clearance between the two inverters.
Install the inverter at an appropriate height for ease of viewing LED indicator and operating
switch(es).
4.3 Installation Tools
Installation tools include but are not limited to the following recommended ones. If necessary,
use other auxiliary tools on site.
table 4-1 Tool specification
Goggles Earplugs Dust mask Protective gloves
20
Insulated shoes Utility knife Slotted screwdriver Phillips screwdriver

(M2, M6) (M4, M6, M8)
Hammer drill Pliers Marker Level

(φ12, φ14)
Rubber mallet Socket wrench set Wrench Wrist strap

(16mm) (13 mm, 16 mm)
Wire cutter Wire stripper Hydraulic plier Heat gun
MC4 terminal MC4 terminal Multimeter RJ45 crimping tool

crimping pliers wrench ≥ 1100 Vdc
4–6mm2
Vacuum cleaner
21
4.4 Moving the Inverter
Before installation, remove the inverter from the packing case and move it to the installation
site. Follow the instructions below as you move the inverter:
• Always be aware of the weight of the inverter.
• Lift the inverter using the handles positioned on both sides of the inverter.
• Move the inverter by one or two people or by using a proper transport tool.
• Do not release the equipment unless it has been firmly secured.
Improper handling may cause personal injury!
• Arrange an appropriate number of personnel to carry the inverter according to

its weight, and installation personnel should wear protective equipment such
as anti-impact shoes and gloves.
• Attention must be paid to the center of gravity of the inverter to avoid tilting dur-
ing handling.
• Placing the inverter directly on a hard ground may cause damage to its metal
enclosure. Protective materials such as sponge pad or foam cushion should be
placed underneath the inverter.
• Move the inverter by holding the handles on it. Do not move the inverter by
holding the terminals.
4.4.1 Manual Transport
Lift and move the inverter to the destination by using the side handles and bottom handles.
4.4.2 Hoisting Transport

step 1 Release the sealing screws on the mounting lugs and store them properly. Anchor two M12
thread lifting rings to the lugs of the inverter.
22
step 2 Lead the sling through the two lifting rings and fasten the tie-down strap.
step 3 Hoist the inverter, and stop to check for safety when the inverter is 100mm above the
ground. Continue hoisting the device to the destination after ensuring the safety.
step 4 Remove the lifting rings and reassemble the sealing screws released in Step 1.
Keep the inverter balanced throughout the hoisting process and avoid collisions
with walls or other objects.
Stop hoisting in the event of severe weather, such as heavy rain, thick fog, or
strong wind.
23
The lifting rings and the sling are not within the delivery scope.
- - End
4.5 Installing Mounting-bracket
Inverter is installed on the wall and bracket by means of mounting bracket.

The expansion plug set shown below is recommended for the installation.
figure 4-1 Dimensions of Mounting-bracket
4.5.1 PV Bracket-Mounted Installation

step 1 Assemble the mounting-bracket.
step 2 Level the assembled mounting-bracket by using the level, and mark the positions for drilling
holes on the PV bracket. Drill the holes by using a hammer drill.
step 3 Secure the mounting-bracket with bolts.
24
No. Components Description

A Mounting-bracket –
B Full threaded bolt M10*45
C Metal bracket –
D Flat washer –
E Spring washer –
F Hex nuts –
- - End
4.5.2 Wall-Mounted Installation

step 1 Assemble the mounting-bracket.
step 2 Level the assembled mounting-bracket by using the level, and mark the positions for drilling
holes.
step 3 Insert the expansion bolts into the holes and secure them with a rubber hammer. Fasten the
nut with a wrench to expand the bolt. Remove the nut, spring washer, and flat washer, and
store them properly.
25
step 4 Install the mounting-bracket to the wall with the expansion bolts with the expansion bolts.
No. Components Description

A Wall –
Fastening the bolt in the sequence of nut, spring wash-
B Expansion bolt
er, slat washer
C Mounting-bracket –
- - End
4.6 Installing the Inverter
step 1 Take out the inverter from the packing case.
step 2 If the installation position is high, hoist the inverter to the position (refer to ""4.4.2 Hoisting
Transport""). Otherwise, skip this step.
step 3 Hang the inverter to the mounting-bracket and ensure that the mounting ears perfectly en-
gage with the mounting-bracket.
step 4 Fix the inverter with screws.
26
- - End
27
5 Electrical Connection
5.1 Safety Instructions

connections.
• Must ensure that cables are voltage-free with a measuring instrument before
touching DC cables.
• Before electrical connections, please make sure that the inverter switch and all
switches connected to the inverter are set to "OFF", otherwise electric shock
may occur!
• Ensure that the inverter is undamaged and all cables are voltage free before
performing electrical work.
• Do not close the AC circuit breaker until the electrical connection is completed.
Damage to the product caused by incorrect wiring is not covered by the warranty.
• Electrical connection must be performed by professionals.

connections.
• All cables used in the PV generation system must be firmly attached, properly
insulated, and adequately dimensioned.
All electrical connections must comply with local and national/regional electrical
standards.
• Cables used by the user shall comply with the requirements of local laws and
regulations.
• Only with the permission of the national/regional grid department, the inverter
can be connected to the grid.
28
User Manual 5 Electrical Connection
• All vacant terminals must be covered with waterproof covers to prevent affect-
ing the protection performance.
• When the wiring is completed, seal the gap at the cable inlet and outlet holes
with fireproof/waterproof materials such as fireproof mud to prevent foreign
matter or moisture from entering and affecting the long-term normal operation
of the inverter.
• Comply with the safety instructions related to PV strings and the regulations re-
lated to the utility grid.
The cable colors in figures in this manual are for reference only. Please select ca-
bles according to local cable standards.
5.2 Terminal Description
All electrical terminals are located at the bottom of the inverter.
figure 5-1 Terminal Description
* The image shown here is for reference only. The actual product received may differ.
29
5 Electrical Connection User Manual
Item Terminal Mark Note

MC4 PV connector
SG30CX, SG30CX-NI, SG33CX: 6 pairs of
A PV terminals +/- terminals
SG40CX: 8 pairs of terminals
SG50CX, SG50CX-NI: 10 pairs of terminals
COM1 For RS485 communication wiring.
Communica- COM2 For Communication module connection.
B
tion terminal COM3 For digital input and output DI/DO wiring.
COM4 For DRM communication wiring.
AC junction Remove the protective case and use the junc-
C —
box tion box in the shipping accessory for wiring.
External pro-
tective
E use at least one of them to ground the inverter.
grounding
terminal
5.3 Electrical Connection Overview
The electrical connection should be realized as follows:
Item Designation
A PV string
B Inverter
C Grid
D Monitoring device
E AC circuit breaker
30
table 5-1 Cable Requirements
Specification
No. Cable Type Cable Diame- Cross-sectional Area
ter(mm) (mm2)
PV cable comply-
1 DC cable ing with 1,500V 6~9 4~6
standard
Additional Outdoor single-
The same as that of the PE wire in the AC
2 grounding core copper wire
cable
cable cable
L1,L2,L3,N wire (SG30CX,
SG30CX-NI, SG33CX): 16
~ 70
Outdoor multicore L1,L2,L3,N wire (SG40CX):
3 AC cable copper or alumi- 20 ~ 50 25 ~ 70
nium cable L1,L2,L3,N wire (SG50CX,
SG50CX-NI): 35 ~ 70
PE wire: refer to "table 5-2
PE Wire Requirements"
Shielded twisted
Communi- pair (terminal 0.1 ~ 1.5
4 cation block) 4.5 ~ 18
cable CAT-5 Ethernet ca-
/
ble (RJ45)
table 5-2 PE Wire Requirements
Phase Wire Cross PE Wire Cross

Note
Section S Section
16＜S≤35mm2 16mm2 The specifications are valid only when
the phase wire and PE wire use the
same material. If otherwise, ensure that
S＞35 mm2 S/2 the cross section of the PE wire produ-
ces a conductance equivalent to that of
the wire specified in the table.
31
5.4 Crimp OT/DT terminal

Crimp OT/DT terminal
1. Heat shrink tubing 2. OT/DT terminal
3. Hydraulic pliers 4. Heat gun
Aluminum Cable Requirements

If an Aluminum cable is selected, use a copper to Aluminum adapter terminal to avoid direct
contact between the copper bar and the Aluminum cable.
figure 5-2 Aluminum Cable Connection
1. Copper to Aluminum adapter terminal 2. Flange nut 3. Aluminum cable
Ensure that the selected terminal can directly contact with the copper bar. If there
are any problems, contact the terminal manufacturer.
Ensure that the copper bar is not in direct contact with the aluminum wire. Other-
wise, electrochemical corrosion may occur, impairing the reliability of electrical
connection.
32
5.5 External Protective Grounding Connection
Electric shock!
• Make sure that the grounding cable is connected reliably. Otherwise, it may
cause electric shock.
• Since the inverter is not equipped with a transformer, neither the negative elec-
trode nor the positive electrode of the PV string can be grounded. Otherwise,
the inverter will not operate normally.
• Connect the grounding terminal to the external protective grounding point be-
fore AC cable connection, PV string connection, and communication cable
connection.
The external protective grounding terminal must meet at least one of the following
requirements.
• The cross-sectional area of the grounding cable is not less than 10 mm2 for cop-
per wire or 16 mm2 for aluminum wire. It is recommended that both the external
protective grounding terminal and the AC side grounding terminal be reliably
grounded.
• If the cross-sectional area of the grounding cable is less than 10 mm2 for copper
wire or 16 mm2 for aluminum wire, ensure that both the external protective
grounding terminal and the AC side grounding terminal are reliably grounded.
The grounding connection can be made by other means if they are in accordance
with the local standards and regulations, and SUNGROW shall not be held liable
for the possible consequences.
5.5.1 External Protective Grounding Requirements
All non-current carrying metal parts and device enclosures in the PV power system should
be grounded, for example, brackets of PV modules and inverter enclosure.
When there is only one inverter in the PV system, connect the external protective grounding
cable to a nearby grounding point.
When there are multiple inverters in the PV system, connect the external protective ground-
ing terminals of all inverters and the grounding points of the PV module brackets to ensure
equipotential connections to ground cables (according to the onsite conditions).
5.5.2 Connection Procedure

step 1 Prepare the cable and OT/DT terminal, refer to " Crimp OT/DT terminal".
33
step 2 Remove the screw on the grounding terminal and fasten the cable with a screwdriver.
step 3 Apply paint to the grounding terminal to ensure corrosion resistance.
The grounding screws have been anchored to the side of the inverter before deliv-
ery, and do not need to be prepared.
There are two grounding terminals. Use one of them to ground the inverter.
- - End
5.6 AC Cable Connection

5.6.1 AC Side Requirements
Only with the permission of the local grid department, the inverter can be con-
nected to the grid.
Before connecting the inverter to the grid, ensure the grid voltage and frequency comply with
requirements, for which, refer to "Technical Data". Otherwise, contact the electric power
company for help.
AC Circuit Breaker
An independent circuit breaker or fuse should be installed on the output side of the inverter
to ensure safe disconnection from the grid.
Inverter Recommended rated voltage Recommended rated current

SG30CX 63A
SG33CX 63A
SG40CX 80A
400V
SG50CX 100A
SG30CX-NI 63A
SG50CX-NI 100A
34
AC circuit breakers should be installed on the output side of the inverter and the
grid side to ensure safe disconnection from the grid.
• Determine whether an AC circuit breaker with greater overcurrent capacity is re-

quired based on actual conditions.
• Do not connect any local load between the inverter and the AC circuit breaker.
• Multiple inverters cannot share one AC circuit breaker.
Residual Current Monitoring Device

With an integrated universal current-sensitive residual current monitoring unit included, the
inverter will disconnect immediately from the mains power once a fault current with a value
exceeding the limit is detected.
However if an external residual current device (RCD) (type A is recommended) is mandatory,
the switch must be triggered at the residual current. RCD of other specifications can also be
used according to local standard. The recommended residual current is as follows.
Inverter Recommended residual current

SG30CX 330 mA
SG33CX 330 mA
SG40CX 400 mA
SG50CX 500 mA
SG30CX-NI 330 mA
SG50CX-NI 500 mA
Multiple Inverters in Parallel Connection

If multiple inverters are connected in parallel to the grid, ensure that the total number of par-
allel inverters does not exceed 30.
MV Transformer
The MV transformer used together with the inverter should meet the following requirements:
• A distribution transformer can be used if it is designed for the typical cyclical loads of a
PV system (there is load in the day and no load at night).
• A liquid-immersed type transformer or a dry type transformer can be used, and the shield
winding is not a requisite.
• The line-to-line voltage on the LV side of the transformer should endure the output volt-
age of inverter. When the transformer is connected to the IT grid, to-ground withstanding
voltage of the LV winding of the transformer, the LV side AC cables, and the LV side sec-
ondary equipment (including the relay protection device, detection & measuring device,
and other related auxiliary devices) should not be lower than 1,100V.
• The line-to-line voltage on the HV side of the transformer should comply with the local
power grid voltage.
• A transformer with a tap changer on the HV side is recommended in order to keep the
voltage consistent with the grid voltage.
35
• At an ambient temperature of 45℃, the transformer can run in 1.1 times of load for long
time.
• A transformer with a short-circuit impedance 6% (permissible tolerance: ±10%) is

recommended.
• The voltage drop of system cable is no more than 3%.
• The DC component that the transformer can withstand is 1% of the fundamental current
at rated power.
• For thermal rating, the load curve of the transformer and environment conditions should
be taken into account.
• The apparent power of the inverter should never exceed the power of the transformer.
The maximum AC current of all inverters connected in parallel must be taken into ac-
count. It is recommended that the total number of inverters that are connected to the grid
not exceed 30.
• The transformer must be protected against overloading and short circuit.
• The transformer is an important part of grid-connected PV generation system. The fault

tolerance capacity of the transformer should be taken into account at all times. The fault
include: system short circuit, grounding fault, voltage drop, etc.
• Take ambient temperature, relative humidity, altitude, air quality, and other environmental
conditions into account when selecting and installing the transformer.
5.6.2 Requirements for OT/DT Terminal
OT/DT terminals (not included in the delivery scope) are required for fixing AC cables to the
terminal block. Purchase the OT/DT terminals according to the following requirements.
• Specification: M8;
• Dimensions: a≤30mm / 8.4mm≤b≤10.5mm / c≤16mm
High voltage may be present in inverter!

Ensure all cables are voltage-free before electrical connection.
Do not connect the AC circuit breaker until all inverter electrical connections are
completed.
step 1 Disconnect the AC-side circuit breaker and prevent it from inadvertent reconnection.
step 2 Take out the AC junction box and loosen the swivel nut. Remove the seals and select an ap-
propriate one according to cable outer diameter. Lead the cable through the swivel nut, seal,
and junction box successively.
36
Outer diameter D(mm) Seals

20~25 a+b+c+d
25~30 a+b+c
30~40 a+b
40~50 a
step 3 Strip the protection layer and insulation layer by specific length, as described in the figure
below.
step 4 Make the cable and crimp OT/DT terminal,refer to " Crimp OT/DT terminal".
step 5 Unfasten the buckle and remove the protective cap.
step 6 Secure the wires to corresponding terminals.
Observe the terminal layout on the block. Do not connect the phase wires to "PE"
terminal or PE wire to "N" terminal. Otherwise, unrecoverable damage to the inver-
ter may follow.
37
Ensure that the depth L of the socket used is not less than 18mm.
step 7 Secure the junction box, fasten the buckle, and secure it with supplied M4×10 screw.
step 8 Gently pull the cable backwards to ensure firm connection, and fasten the swivel nut
clockwise.
38
- - End
5.7 DC Cable Connection
• Make sure the PV array is well insulated to ground before connecting it to the
inverter.
• Make sure the maximum DC voltage and the maximum short circuit current of
any string never exceed inverter permitted values specified in "Technical Data".
• Check the positive and negative polarity of the PV strings, and connect the PV
connectors to corresponding terminals only after ensuring polarity correctness.
• During the installation and operation of the inverter, please ensure that the posi-
tive or negative electrodes of PV strings do not short-circuit to the ground. Oth-
erwise, an AC or DC short-circuit may occur, resulting in equipment damage.
The damage caused by this is not covered by the warranty.
• Electric arc or contactor over-temperature may occur if the PV connectors are

not firmly in place, and SUNGROW shall not be held liable for any damage
caused.
• If the DC input cables are reversely connected or the positive and negative ter-
minals of different MPPT are shorted to ground at the same time, while the DC
switch is in the "ON" position, do not operate immediately. Otherwise, the inver-
ter may be damaged. Please turn the DC switch to "OFF" and remove the DC
connector to adjust the polarity of the strings when the string current is lower
than 0.5 A.
39
The following requirements about PV string connection must be met. Otherwise, it

may cause irreversible damage to the inverter, which is not covered by the
warranty.
• Mixed use of PV modules of different brands or models in one MPPT circuit, or

PV modules of different orientation or inclination in a string may not damage in-
verter, but will cause system bad performance!
• The inverter enters standby state when the input voltage ranges between 1,000
V and 1,100 V. The inverter returns to running state once the voltage returns to
the MPPT operating voltage range, namely, 200 V to 1,000 V.
5.7.1 PV Input Configuration

• As shown in the figure below, the inverter is provided with multiple PV inputs: PV inputs
1~n (SG30/33/40/50CX: n=3/3/4/5); and each PV input is designed with an MPP tracker.
• Each PV input operates independently and has its own MPPT. In this way, string struc-
tures of each PV input may differ from each other, including PV module type, number of
PV modules in each string, angle of tilt, and installation orientation.
• Each PV input area includes two DC inputs DC1 and DC2. For the best use of DC power,
DC1 and DC2 should be the same in PV string structure, including the type, number, tilt,
and orientation of the PV modules.
figure 5-3 PV Input Configuratinon
Prior to connecting the inverter to PV inputs, the specifications in the following table should
be met:
Open-circuit Voltage Max. Current for Input

Type
Limit Connector
SG30/33/40/50CX 1100 V 30 A
SG30/50CX-NI 1100 V 30 A
40
5.7.2 Assembling PV Connectors
High voltage may be present in the inverter!
• Ensure all cables are voltage-free before performing electrical operations.
• Do not connect the AC circuit breaker before finishing electrical connection.
• Use MC4 DC terminals if the maximum input voltage is no more than 1,000 V.
• Use MC4-Evo2 DC terminals if the maximum input voltage is greater than 1,000
V. To purchase the MC4-Evo2 DC terminals, contact SUNGROW.
• Select appropriate DC terminals as required above. Otherwise, SUNGROW shall

be held no liability for the damage caused.
To ensure IP66 protection, use only the supplied connector.
step 1 Strip 7 mm–8 mm of the insulation from each PV cable.
step 2 Assemble the cable ends with the crimping pliers.
1: Positive crimp contact 2: Negative crimp contact
step 3 Lead the cable through the cable gland, and insert the crimp contact into the insulator until it
snaps into place. Gently pull the cable backward to ensure firm connection. Tighten the ca-
ble gland and the insulator (torque 2.5 N.m to 3 N.m).
41
step 4 Check for polarity correctness.
- - End
5.7.3 Installing PV Connector

step 1 Rotate the DC switch to “OFF” position.
step 2 Check the cable connection of the PV string for polarity correctness and ensure that the
open circuit voltage in any case does not exceed the inverter input limit of 1,100V.
step 3 Connect the PV connectors to corresponding terminals until there is an audible click.
42
step 4 Follow the foregoing steps to connect PV connectors of other PV strings.
step 5 Seal any unused PV terminal with a terminal cap.
If the PV string is equipped with the optimizer, please refer to the optimizer manual for elec-
trical connections and make sure that the polarity of the optimizer cables is correct.
- - End
5.8 Communication Junction Box

Remove the Junction Box
Pull out the pin and keep it properly, remove the junction box.
The pin removed is a required accessory for fixing the junction box. Store it prop-
erly and protect it against missing or deformation.
Install the Junction Box

Remount the wiring box and press it tightly, insert the pin, and secure the wiring box with the
supplied M4×25 screw.
43
During installation, firmly press the junction box to ensure that the pin can be in-
serted successfully.
Never hit the pin with a heavy object, such a hammer. Otherwise, it will be irrecov-
erably damaged.
5.9 Communication Wiring Board
The communication board of the inverter includes two layers. The upper layer communica-
tion board mainly includes RS485 communication interfaces while the lower layer communi-
cation board mainly includes DI/DO interface and DRM interface.
5.10 RS485 Connection

5.10.1 Interface Description
As shown in the Figure below, the inverter is equipped with three RS485 communication in-
terfaces and one dip switch.
44
All three interfaces can be connected to a data acquisition device (Data Logger), to achieve
data exchange with PC or other monitoring devices.
The RS485-1 crimp and the RJ45 interface can be applied to applications where multiple in-
verters communicate in a daisy-chain form.
A 120Ω resistor can be connected in parallel between RS485-1 A/B pins by configuring the
dip switch.
RS485-1 crimp interface and RJ45 interface serve as the same function with differ-
ent wiring manner.
5.10.2 RS485 Communication System

Single-inverter Communication System
In case of a single inverter, communication cable connection requires only one RS485 cable.
figure 5-4 Single-inverter Connection

Multi-inverter Communication System
In case of multiple inverters, all the inverters can be connected via RS485 cables in the
daisy chain manner.
45
figure 5-5 Multi-inverter Connection
When more than 15 inverters are connected to the same daisy chain, in order to ensure the
communication quality, the Logger at the first end of the daisy chain needs to be equipped
with a terminal resistor of 120Ω, the inverter at the last end needs to be equipped with a
RS485-dip switch (SW1), and the shielding layer of the communication cable should be sin-
gle-point grounded.
figure 5-6 Configuration of Dip Switch (N≥15)
The length of the RS485 cable and twisted pair cable should be no longer than
1,200m.
If multiple inverters are connected to the data logger, the number of permissible
daisy chains and the number of devices allowed to be connected should meet the
requirements (refer to the user manual for the data logger).
46
5.10.3 Connection Procedure(Terminal Block)
RS485 communication cables should be shielded twisted pair cables or shielded

twisted pair Ethernet cables.
There are three communication terminals, and the silkscreen marks are COM1/
COM2/COM3. Please choose according to the actual situation.
step 1 Remove the communication junction box, see" Remove the Junction Box".
step 2 Strip the protection layer and insulation layer by appropriate length.
step 3 Loosen the swivel nut of the junction box and select an appropriate seal according to cable
outer diameter. Lead the cable through the swivel nut, seal, and junction box successively.
Outer Diameter D(mm) Seal

4.5 ~ 6 c
6 ~ 12 a+b
12 ~ 18 b
step 4 Secure the cable to the terminal base.
47
step 5 Insert the terminal base into the corresponding terminal.
table 5-3 Terminal definition
No Definition
1 RS485 A IN, RS485A differential signal+
2 RS485 A OUT, RS485A differential signal+
3 RS485 B IN, RS485B differential signal-
4 RS485 B OUT, RS485B differential signal-
step 6 If other wiring operations need to be performed on the communication board, finish the wir-
ing operations before performing the following steps. If otherwise, continue to perform the
following steps.
step 7 Install the junction box, see " Install the Junction Box".
step 8 Pull the cable gently to make sure it is secured, tighten the swivel nut clockwise.
- - End
5.10.4 Connection Procedure (RJ45 Ethernet Port)

step 1 Remove the communication junction box, see " Remove the Junction Box".
step 2 Loosen the swivel nut of the junction box and select an appropriate seal according to cable
outer diameter. Lead the cable through the swivel nut, seal, and junction box successively.
48
Outer Diameter D(mm) Seal

4.5 ~ 6 c
6 ~ 12 a+b
12 ~ 18 b
step 3 Strip the insulation layer of the Ethernet cable with a wire stripper, and insert the signal wires
to the RJ45 connector(Pin 3 and Pin 6 are for communication connection). Crimp the RJ45
connector with a crimping tool.
step 4 Insert the RJ45 connector to the RJ45 jack.
following steps.
- - End
49
5.11 Dry Contact Connection
Dry contact cables require a cross section of 1 mm2 to 1.5 mm2.

The connection procedure of the dry contact is the same as that of the RS485 ter-
minal block.
5.11.1 Dry Contact Function
The configuration circuit board is provided with fault output dry contact and emergency stop
dry contact, as shown in the figure below.
Connection method of the dry contacts is similar to that of the RS485 terminal block.
DO terminal (fault output dry contact): The relay can be set to output fault alarms, and
user can configure it to be a normally open contact (COM＆NO) or a normally closed contact
(COM＆NC).
The relay is initially at the NC contact, and it will trip to another contact when a fault occurs.
When alarm occurs, signal status change will not be triggered.
Use LED indicators or other equipment to indicate whether the inverter is in the faulty state.
The following Figures show the typical applications of normal open contact and normaliy
closed contact:
50
figure 5-7 Normally open contact
figure 5-8 Normally closed contact
Devices connected to the relay should comply with related requirements:
AC-Side Requirements DC-Side Requirements

Max. voltage: 250 Vac Max. voltage: 30Vdc
Max. current: 5A Max. current: 5A
DI terminal (emergency stop dry contact): the dry contact can be configured to be an
emergency stop contact.
When the DI contact and GND contact are shorted by external controlled switch (The exter-
nal switch can be configured as normally open contact or normally closed contact), the inver-
ter will immediately stop.
NS terminal: NS Protection is currently used for German market. For plant sized more than
30kVA, inverter NS Protection terminals could be used in daisy chain to external NS Protec-
tion Relay to realize emergency stop when NS Protection Relay change its dry contact sta-
tus due to the grid abnormal running status.
NS Protection (including Passive Valid) can be set. When NS Protection is enabled on the
iSolarCloud, the inverters will operate normally when DI contact and GND contact are
shorted by external controlled switch, and the inverters will emergently stop when DI contact
and GND contact are disconnected.
The dry contacts only support passive switch signal input.
The following figure shows the typical application of local stop dry contact.
51
figure 5-9 Local stop contact
figure 5-10 Daisy chain topology
When wiring DI dry contacts, ensure that the maximum wiring distance meet the require-
ments in "10.2 Wring Distance of DI Dry Contact".
5.11.2 Wiring Procedure
Refer to the wiring of terminal block described in chapter"5.10.3 Connection Procedure(Ter-

minal Block)" to implement fault output, emergency shutdown and NS protection. For NS
protection(including passive valid), enable the function on iSolarCloud, refer to "7.8.2 Opera-
tion Parameters".
5.12 DRM Connection（For Countries “AU” and “NZ”）

5.12.1 DRM Function
The inverter supports the demand response modes as specified in the standard AS/NZS
4777. The inverter has integrated a terminal for connecting to a DRED. After the connection,
the method of asserting DRMs as specified in the follow table.
52
The mode DRM0 is supported by the inverter.
table 5-4 Method of Asserting DRMs
Mode Method of Asserting

Asserted by shorting pins 5 and 6
DRM0 Asserted when the impedance between pins 5 and 6 is detected to be
above 20kΩ
Enable the DRM function through the iSolarCloud APP. If there are any problems,
contact your distributor first. If the problem persists, contact SUNGROW.
The DRM function is only applicable to devices for Australia and New Zealand.

step 1 Remove the communication junction box, see" Remove the Junction Box".
step 2 Strip the insulation layer of the Ethernet cable with a wire stripper, and insert the signal wires
to the RJ45 connector. Crimp the RJ45 connector with a crimping tool.
53
step 3 Loosen the swivel nut and select an appropriate seal according to cable outer diameter.
Lead the cable through the swivel nut, and seal successively.
Outer Diameter D
Seal
(mm)
4.5 ~ 6 c
6 ~ 12 a+b
12 ~ 18 b
step 4 Insert the RJ45 connector to the RJ45 jack.
following steps.
54
- - End
5.13 Communication Module Connection (optional)
Connect the communication module produced by SUNGROW to the communication acces-

sory port. After successful connection, information such as power generation and running
state of the inverter can be viewed via the App on the phone.
*The image shown here is for reference only. The actual product you receive may differ.
Once the communication module is in use, do not connect the inverter to a 3rd
party data logger at the same time via RS485.
For details on module installation and configuration, refer to the manual delivered
together with the module.
55
6 Commissioning
6.1 Inspection Before Commissioning
Check the following items before starting the inverter:
• All equipment has been reliably installed.
• DC switch(es) and AC circuit breaker are in the "OFF" position.
• The ground cable is properly and reliably connected.
• The AC cable is properly and reliably connected.
• The DC cable is properly and reliably connected.
• The communication cable is properly and reliably connected.
• The vacant terminals are sealed.
• No foreign items, such as tools, are left on the top of the machine or in the junction box (if
there is).
• The AC circuit breaker is selected in accordance with the requirements of this manual
and local standards.
• All warning signs & labels are intact and legible.
6.2 Commissioning Procedure
If all of the items mentioned above meet the requirements, proceed as follows to start up the
inverter for the first time.
step 1 Connect the AC switch or circuit breaker between the inverter and the grid.
step 2 Rotate the DC switch of the inverter to "ON" position.
step 3 Connect the DC switch (if applicable) between the inverter and the PV string.
step 4 Set initial protection parameters via the iSolarCloud App. For details, please refer to "7.2 In-
stalling App",and "7.4.2 Login Procedure". If the irradiation and grid conditions meet require-
ments, the inverter will normally operate.
step 5 Observe the LED indicator to ensure that the inverter operates normally. Refer to "2.4 LED
Indicator" for details.
- - End
56
7 iSolarCloud App
7.1 Brief Introduction
The iSolarCloud App can establish communication connection to the inverter via the Blue-
tooth, thereby achieving near-end maintenance on the inverter. Users can use the App to
view basic information, alarms, and events, set parameters, or download logs, etc.
*In case the communication module Eye, WiFi or WiNet-S is available, the iSolarCloud App
can also establish communication connection to the inverter via the mobile data or WiFi,
thereby achieving remote maintenance on the inverter.
• This manual describes only how to achieve near-end maintenance via the
Bluetooth connection. For remote maintenance through the Eye, WiFi or
WiNet-S, refer to the related manuals in the delivery scope.
• Screenshots in this manual are based on the Android system V2.1.6 , and the
actual interfaces may differ.
7.2 Installing App

Method 1
Download and install the App through the following application stores:
• MyApp (Android, mainland China users)
• Google Play (Android, users other than mainland China ones)
• App Store (iOS)

Method 2
Scan the following QR code to download and install the App according to the prompt
information.
The App icon appears on the home screen after installation.
57
7 iSolarCloud App User Manual
7.3 Function Overview
The App provides parameter viewing and setting functions, as shown in the following figure.
figure 7-1 App Function Tree Map
7.4 Login
7.4.1 Requirements
The following requirements should be met:
• The AC or DC side of the inverter is powered-on.
• The mobile phone is within 5 meters away from the inverter and there are no obstructions
in between.
• The Bluetooth function of the mobile phone is enabled.
The inverter can only pair with one phone at a time through Bluetooth.
7.4.2 Login Procedure

step 1 Open the App to enter the login page, tap Local Access at the bottom of the page to go to
the next page.
step 2 Establish the Bluetooth connection by either of the two following ways. If the LED indicator
flashes blue, the connection is successfully established.
• Scan the QR code on the side of the inverter for Bluetooth connection.
58
User Manual 7 iSolarCloud App
• Tap "Manual connection" and select "Others" at the bottom of the page, the Bluetooth
search page will automatically pop up, and select the inverter to be connected according
to the SN on the nameplate on the side of the inverter body.
figure 7-2 Bluetooth Connection
step 3 Enter the identity verification interface after the Bluetooth connection is established.
59
figure 7-3 Login
The Account is “user”，and the initial password is "pw1111" or "111111" which

should be changed for the consideration of account security.
To set inverter parameters related to grid protection and grid support, contact
SUNGROW to obtain the advanced account and corresponding password.
step 4 If the inverter is not initialized, you will enter the quick setting interface of initializing protec-
tion parameter. Tap Country/Region to select the correct country, as shown in the following
figure.
figure 7-4 Initialization Country/Region
Reset the protection parameters if the country setting is incorrect. Otherwise, a

fault may occur.
60
In the European region, such as Sweden, Norway, Hungary, Portugal, Romania,

Greece, Ukraine etc. whose grid code complies with EN50549, select the parame-
ter EN50549_1 (LV grid- connection) or EN50549_2 (MV grid-connection) with
proper manual settings.
In the Brazilian region, set the country code as "Brazil". Selecting "Brazil_230" or
"Brazil_240" will cause setting failure.
For SG30CX, set the grid code as EN50549 in the Ukraine region and apply man-
ual settings for country code compliance.
step 5 When the country is set to Australia, additionally set the applicable network service provider
and then the grid type.Tap Power Company to select the correct power company.
figure 7-5 Initialization Power Company
The image shown here is for reference only. Refer to the actual interface for the supported
network service providers.
table 7-1 Power Company Information
Network Service Provider Grid Type

AS/NZS 4777.2:2015 /
AS/NZS 4777.2:2020 Australia A /
AS/NZS 4777.2:2020 Australia B /
AS/NZS 4777.2:2020 Australia C /
ENERGEX & Ergon Energy
• STNW1170: single phase < 10 kVA &
three phase < 30 kVA
• STNW1174 :30 kVA ＜ PN ≤ 1500 kVA

Endeavour Energy MDI 0043
Ausgrid NS194
Jemena
• ≤ 10kVA per phase (or 30 kVA per three
phase)
• ELE GU 0014: 30-200kVA
61
Network Service Provider Grid Type

CitiPower & Powercor
• ≤ 5 kVA for single-phase & 30 kVA for
three-phase
• > 30 kVA three-phase

United Energy
• UE-ST-2008.1: ≤ 10 kW for single-
phase & 30 kW for three-phase
• UE-ST-2008.2: > 30 kVA three-phase

PowerWater Embedded Generation Notice Photovoltaic
Systems:2020
SA Power Networks
• TS129-2019: < 10 kW for single-phase
& 30 kW for three-phase
• TS130-2017: > 30 kW & ≤ 200 kW
• TS131-2018: > 200 kW

Horizon Power
• HPC-9DJ-13-0001-2019: ≤ 10 kVA for
single-phase & 30 kVA for three-phase
• HPC-9DJ-13-0002-2019: > 30 kVA &

≤1 MVA
westernpower EDM＃33612889-2019
AusNet Services Basic Micro Embedded Generation:2020
For compliance with AS/NZS 4777.2:2020, please select from Australia A/B/C. Please con-
tact your electricity grid operator for which region to use.
step 6 After finishing the settings, tap TUNR ON DEVICE at the upper right corner and the device
will be initialized. The App will send start instructions and the device will start and operate.
step 7 After initialization settings, the App will return automatically to the home page.
- - End
7.5 Home
After login, the home page is as follows:
62
figure 7-6 Home Page
table 7-2 Home Page Description
No. Designation Description

1 Date and time System date and time of the inverter
Present operation state of the inverter. For details, refer to
2 Inverter state
"table 7-3 Description of Inverter State".
Present state of the PID function. For details, refer to "table
3 PID function state
7-4 Description of PID State"
Display the PV power generation power, feed-in power, etc.
The line with an arrow indicates energy flow between con-
4 Power flow chart
nected devices, and the arrow pointing indicates energy
flow direction.
Today power yield and accumulative power yield of the
5 Power generation
inverter
6 Real-time power Output power of the inverter
Curve showing change of power between 5 am and 23 pm
every day
7 Power curve
(Each point on the curve represents the percentage of
present inverter power to rated power)
Including "Home", "Run Information", "Records", and
8 Navigation bar
"More"
63
table 7-3 Description of Inverter State
State Description
After being energized, inverter tracks the PV arrays’ maximum power
Run point (MPP) and converts the DC power into AC power. This is the nor-
mal operation mode.
Stop Inverter is stopped.
Press to Shut Inverter will stop operation by tapping "Stop" via app. In this way, inverter
Down internal DSP stops. Restart the inverter via app if needed.
Inverter enters standby mode when DC side input is insufficient. In this
Standby
mode inverter will wait within the standby duration.
Initial standby The inverter is in the initial power-on standby state.
Starting up The inverter is initializing and synchronizing with the grid.
Warn run Warning information is detected.
Derating The inverter derates actively due to environmental factors such as tem-
running perature or altitude
Dispatch The inverter runs according to the scheduling instructions received from
Running the monitoring background
If a fault occurs, inverter will automatically stop operation, and the AC re-
lay acts. The fault information will be displayed on the app. Once the
Shut down
fault is removed in recovery time, inverter will automatically resume
running.
table 7-4 Description of PID State
State Description
PID recovery
The inverters perform PID recovery actively.
running
It is detected that the ISO impedance is abnormal or the PID cannot
PID abnormity
work normally after the PID function is enabled.
If the inverter is running abnormally, the alarm or fault icon will be displayed in the lower
right corner of the inverter icon in power flow chart. The user can tap this icon to enter the
alarm or fault interface to view detailed information and corrective measures.
7.6 Run Information
Tap Run Information on the navigation bar to enter the screen showing running information,
slide the screen upwards to view all detailed information.
64
table 7-5 Run Information
Classifica-
Parameter Description
tion
PV String n Voltage The input voltage of the nth string
Information String n current The input current of the nth string
Total On-grid Run-
/
ning Time
Daily On-grid Run-
/
ning Time
Negative Voltage to
Inverter DC side negative to ground voltage value
Ground
Voltage between the positive and negative poles
Bus Voltage
of the DC side of the inverter
Inverter
Internal Air
Information /
Temperature
Array Insulation Insulation resistance value of the input side to the
Resistance protection ground
Country Information /
Power Limitation
/
Mode
Reactive Power
/
Mode
Total DC Power DC side total input power
Input MPPT x Voltage The input voltage of the xth MPPT
MPPT x Current The input current of the xth MPPT
Daily Yield /
Monthly Yield /
Annual Yield /
Total Active Power Current active power value of the inverter
Total Reactive Power Current reactive power value of the inverter
Total Apparent
Current apparent power value of the inverter
Power
Output
Total Power Factor Power factor of the AC side of the inverter
Gird Frenquency Frequency of the AC side of the inverter
A-B Line Voltage
B-C Line Voltage Line voltage
C-A Line Voltage
Phase A Current
Phase current
Phase B Current
65
Classifica-
tion
Phase C Current
7.7 Records
Tap Records on the navigation bar to enter the interface showing event records, as shown
in the following figure.
figure 7-7 Records

Fault Alarm Record
Tap Fault Alarm Record to enter the interface, as shown in the following figure.
figure 7-8 Fault Alarm Record
Tap to select a time segment and view corresponding records.

The inverter can record up to 400 latest entries.
Select one of the records in the list and tap the record to view the detailed fault information
as shown in following figure.
66
figure 7-9 Detailed Fault Alarm Information

Yield Record
Tap Yield Record to enter the interface showing daily power generation as shown in the fol-
lowing figure.
figure 7-10 Power Curve
The App displays power generation records in a variety of forms, including daily power gen-
eration graph, monthly power generation histogram, annual power generation histogram
and total power generation histogram.
table 7-6 Yield Record Explanation
Shows the power output from 5 am to 23 pm in a single day. Each
Power curve point on the curve represents the percentage of present inverter
power to rated power.
Daily yield
Shows the power output every day in the present month.
histogram
67
Monthly yield
Shows the power output every month in a year.
histogram
Annual yield
Shows the power output every year.
histogram
Tap the time bar on the top of the interface to select a time segment and view the corre-
sponding power curve.
Swipe left to check the power yields histogram.
Event Record
Tap Event Record to view event record list.
Click to select a time segment and view corresponding records.

The inverter can record up to 400 latest entries.
7.8 More
Tap More on the navigation bar to enter the corresponding interface, as shown in the follow-
ing figure.
figure 7-11 More
7.8.1 System Parameters
Tap Settings→System Parameters to enter the corresponding interface, as shown in the

following figure.
68
figure 7-12 System Parameters
* The image shown here is for reference only.

Boot/Shutdown
Tap Boot/Shutdown to send the boot/shutdown instruction to the inverter.
For Australia and New Zealand, when the DRM state is DRM0, the "Boot" option will be
prohibited.
Date Setting/Time Setting
The correct system time is very important. Wrong system time will directly affect the data
logging and power generation value. The clock is in 24-hour format.
Software Version
Version information of the current firmware.
7.8.2 Operation Parameters

Running Time
Tap Settings→Operation Parameters→Running Time to enter the corresponding
interface.
figure 7-13 Running Time

PID Parameters
Tap Settings→Operation Parameters→PID Parameters to enter the corresponding
interface.
69
figure 7-14 PID Parameters
table 7-7 PID Parameter Description
Enabling/Disable the PID night recovery function. Once enabled, it
PID Recovery
works between 22:00 pm and 5:00 am by default.
If ISO impedance abnormality or PID function exception is de-
tected during running of the PID function, the inverter reports a
Clear PID alarm PID abnormity and reminds the user to take corresponding meas-
ures. Clear the alarm report via this parameter once the problems
are handled.
Apply negative voltage when the inverter is connected to negative
voltage panel.
PID Scheme
Apply positive voltage when the inverter is connected to positive
voltage panel.
After the PID night recovery function is enabled, the fault indicator on the inverter
front panel turns green.
AFCI Parameters(Optional)
Tap Settings→Operation Parameters→AFCI Parameters to enter the corresponding
screen, on which you can set "AFCI Parameters".
figure 7-15 AFCI Setting

NS Protection(Passive Valid)
Tap Settings→Operation Parameters→Regular Parameters to enter the corresponding
screen, on which you can set the "NS Protection(Passive Valid)".
70
figure 7-16 NS Protection(Passive Valid)
7.8.3 Power Regulation Parameters

Active Power Regulation
Tap Settings→Power Regulation Parameters→Active Power Regulation to enter the
screen, as shown in the following figure.
figure 7-17 Active Power Regulation
table 7-8 Active Power Regulation
Definition/Setting
Parameter Range
Description
Active power soft start The switch for enabling/dis- Enable/Disable

after fault abling the soft start function
after a fault occurs.
Active power soft start Time that the soft start takes to 1s~1200s
time after fault raise the power from 0 to
100% rated power.
Active power gradient Switch for enabling/disabling Enable/Disable

control the active power rate settable
function.
Active power decline The decline rate of inverter ac- 1%/min~6000%/min

gradient tive power per minute.
71
Definition/Setting
Parameter Range
Description
Active power rising The rise rate of inverter active 1%/min~6000%/min

gradient power per minute.
Active power setting Switch for enabling/disabling Enable/Disable

persistence the function of saving output
limited power.
Active power limit The switch for limiting output Enable/Disable

power.
Active power limit ratio The ratio of limiting output 0%~110%

power to rated power in
percentage.
Shutdown when active Switch used to determine Enable/Disable

power limit to 0% whether the inverter is in stop
state when the limited power
reaches 0.
Reactive Power Regulation

Tap Settings→Power Regulation Parameters→Reactive Power Regulation to enter the
screen, as shown in the following figure.
72
figure 7-18 Reactive Power Regulation
table 7-9 Reactive Power Regulation
Definition/Setting
Parameter Range
Description
Reactive power genera- Switch for enabling/disabling Enable/Disable

tion at night Q at night function.
Reactive power ratio at Reactive power ratio set for -100%~0%/

night the Q at night function. 0%~100%
Reactive power setting Switch for enabling/disabling Enable/Disable

persistence the power-off function during
reactive power.
Reactive power regula- — Off/PF/Qt/Q(P)/Q(U)

tion mode
Reactive power Switch for enabling/disabling Enable/Disable

regulation reactive response function.
Reactive power regula- Ends time of reactive 0.1s~600.0s

tion time response.
Q(P)Curve Select corresponding curve Curve A/Curve B/Curve C*

according to local regulations
QP_P1 Output power at P1 on the Q 0.0%~100.0%

(P) mode curve (in
percentage)

(P) mode curve (in
percentage)
73
Definition/Setting
Parameter Range
Description

(P) mode curve (in
percentage)
QP_K1 Power factor at P1 on the Q(P) Curve A/Curve

mode curve C:0.800~1.000
Curve B: [-0.600~0.600]*Ac-
tive Overload Rate/1000
QP_K2 Power factor at P2 on the Q(P) Curve A/Curve C:

mode curve 0.800~1.000
Curve B: [-0.600~0.600]*Ac-
QP_K3 Power factor at P3 on the Q(P) Curve A/Curve C:

mode curve 0.800~1.000
Curve B: [-0.600~0.600]*Ac-
QP_EnterVoltage Voltage percentage for Q(P) 100.0%~110.0%

function activation
QP_ExitVoltage Voltage percentage for Q(P) 90.0%~100.0%

function deactivation
QP_EXitPower Power percentage for Q(P) 1.0%-20.0%

function deactivation
QP_EnableMode Unconditional activation/deac- Yes/No

tivation of Q(P) function
Q(U)Curve Select the corresponding Curve A/Curve B/Curve C*

curve according to local
regulations
QU_V1 Pre-set grid voltage U1 that is 80.0%~100.0%

reactive according to the grid
voltage
QU_Q1 Pre-set proportion of reactive [-60.0%-0]* Overload Rate/

power according to the grid 1000
voltage U1
74
Definition/Setting
Parameter Range
Description

voltage.
QU_Q2 Pre-set proportion of reactive [-60.0%-60.0%]* Overload

power according to the grid Rate/1000
voltage U2.

voltage.
QU_Q3 Pre-set proportion of reactive [-60.0%-60.0%]* Overload

power according to the grid Rate/1000
voltage U3.

voltage.
QU_Q4 Pre-set proportion of reactive [0-60.0%]* Overload Rate/

power according to the grid 1000
voltage U4.
QU_EnterPower Active power for Q(U) function 20.0%~100.0%

activation
QU_EXitPower Active power for Q(U) function 1.0%~20.0%

deactivation
QU_EnableMode Unconditional activation/deac- Yes/No/Yes,Limited by PF

tivation of Q(U) function
QU_Limited PF Value — 0-1
**Curve C is reserved and consistent with Curve A currently.
75
figure 7-19 Q(U) Curve
figure 7-20 Q(P) Curve
7.8.4 Communication Parameters
Tap Settings→Communication Parameters to enter the corresponding screen, as shown

in the following figure. The device address ranges from 1 to 246.
figure 7-21 Communication Parameters
7.8.5 Firmware Update
To avoid download failure due to poor on-site network signal, it is recommended to download
the firmware package to the mobile device in advance.
Perform firmware update only during high irradiance conditions in order to prevent equip-
ment failure.
step 1 Enable the "Mobile data" of the mobile device.
step 2 Open the App, enter the account and password on the login interface. Tap Login to enter
the home interface.
step 3 Tap More→Firmware Download to enter corresponding interface on which you can view
the device list.
76
step 4 Select the device model before downloading the firmware. Tap the device name in the de-
vice list to enter the firmware upgrade package detail interface, and tap behind the firm-
ware upgrade package to download it.
step 5 Return to the Firmware Download interface, tap in the upper right corner of the interface
to view the downloaded firmware upgrade package.
step 6 Login the App via local access. Refer to "7.4 Login".
step 7 Tap More on the App home screen and then tap Firmware Update.
step 8 Tap the upgrade package file, a prompt box will pop up asking whether to upgrade the firm-
ware with the file, tap CONFIRM to perform the firmware upgrade.
step 9 Wait for the file to be uploaded. When the upgrade is finished, a message is displayed indi-
cating that the upgrade is completed. Tap Complete to end the upgrade.
- - End
7.8.6 Password Changing
Tap Modify Password to enter the modify password interface, as shown in the following
figure.
77
figure 7-22 Modify Password
The password shall consisit of 8–20 digits, including letters and numbers.
78
8 System Decommissioning
8.1 Disconnecting Inverter
Danger of burns!
Even if the inverter is shut down, it may still be hot and cause burns. Wear protec-
tive gloves before operating the inverter after it cools down.
For maintenance or other service work, the inverter must be switched off.
Proceed as follows to disconnect the inverter from the AC and DC power sources. Lethal
voltages or damage to the inverter will follow if otherwise.
step 1 Disconnect the external AC circuit breaker and prevent it from inadvertent reconnection
step 2 Rotate the DC switch to the "OFF" position for disconnecting all of the PV string inputs.
step 3 Wait about 5 minutes until the capacitors inside the inverter completely discharge.
step 4 Ensure that the DC cable is current-free with a current clamp.
- - End
8.2 Dismantling the Inverter
Risk of burn injuries and electric shock!

After the inverter is powered off for 5 minutes, measure the voltage and current
with professional instrument. Only when there is no voltage nor current can opera-
tors who wear protective equipment operate and maintain the inverter.
Before dismantling the inverter, disconnect the inverter from both AC and DC
power sources.
If there are more than two layers of inverter DC terminals, dismantle the outer DC
connectors before dismantling the inner ones.
step 1 Refer to "5 Electrical Connection", for the inverter disconnection of all cables in reverse
steps. In particular, when removing the DC connector, use an MC4 wrench to loosen the
locking parts and install waterproof plugs.
79
8 System Decommissioning User Manual
step 2 Refer to"4 Mechanical Mounting", to dismantle the inverter in reverse steps.
step 3 If necessary, remove the wall-mounting bracket from the wall.
step 4 If the inverter will be used again in the future, please refer to "3.2 Inverter Storage" for a
proper conservation.
- - End
8.3 Disposal of Inverter
Users take the responsibility for the disposal of the inverter.
Please scrap the inverter in accordance with relevant local regulations and stand-
ards to avoid property losses or casualties.
Some parts of the inverter may cause environmental pollution. Please dispose of
them in accordance with the disposal regulations for electronic waste applicable at
the installation site.
80
9 Troubleshooting and Maintenance
9.1 Troubleshooting
Once the inverter fails, the fault information is displayed on the App interface. If the inverter
is equipped with an LCD screen, the fault information can be viewed on it.
The fault codes and troubleshooting methods of all PV inverters are detailed in the table be-
low, and only some of the faults may occur to the model you purchased. When a fault occurs,
you can check the fault information according to the fault code on the mobile app.
Fault Code Fault Name Corrective Measures

Generally, the inverter will be reconnected to the
grid after the grid returns to normal. If the fault oc-
curs repeatedly:
1. Measure the actual grid voltage, and contact
the local electric power company for solutions if
the grid voltage is higher than the set value.
2, 3, 14, 15 Grid Overvoltage
2. Check whether the protection parameters are
appropriately set via the App or the LCD. Modify
the overvoltage protection values with the con-
sent of the local electric power operator.
3. Contact Sungrow Customer Service if the pre-
ceding causes are ruled out and the fault persists.
curs repeatedly:
1. Measure the actual grid voltage, and contact
4, 5 Grid Undervoltage the grid voltage is lower than the set value.
2. Check whether the protection parameters are
appropriately set via the App or the LCD.
3. Check whether the AC cable is firmly in place.
81
9 Troubleshooting and Maintenance User Manual

Grid Generally, the inverter will be reconnected to the
8
Overfrequency grid after the grid returns to normal. If the fault oc-
curs repeatedly:
1. Measure the actual grid frequency, and contact
Grid the grid frequency is beyond the set range.
9
Underfrequency 2. Check whether the protection parameters are
appropriately set via the App or the LCD.
curs repeatedly:
1. Check whether the grid supplies power reliably.
2. Check whether the AC cable is firmly in place.
Grid Power 3. Check whether the AC cable is connected to
10
Outage the correct terminal (whether the live wire and
the N wire are correctly in place).
4. Check whether the AC circuit breaker is
connected.
1. The fault can be caused by poor sunlight or
damp environment, and generally the inverter will
be reconnected to the grid after the environment
Excess Leakage is improved.
12
Current 2. If the environment is normal, check whether
the AC and DC cables are well insulated.
curs repeatedly:
1. Measure the actual grid, and contact the local
13 Grid Abnormal
electric power company for solutions if the grid
parameter exceeds the set range.
82
User Manual 9 Troubleshooting and Maintenance

curs repeatedly:
1. Measure the actual grid voltage. If grid phase
voltages differ greatly, contact the electric power
Grid Voltage company for solutions.
17
Imbalance 2. If the voltage difference between phases is
within the permissible range of the local power
company, modify the grid voltage imbalance pa-
rameter through the App or the LCD.
1. Check whether the corresponding string is of
reverse polarity. If so, disconnect the DC switch
and adjust the polarity when the string current
drops below 0.5 A.
28, 29, 208, PV Reserve Con- 2. Contact Sungrow Customer Service if the pre-
212, 448-479 nection Fault ceding causes are ruled out and the fault persists.
*The code 28 to code 29 are corresponding to
PV1 to PV2 respectively.
string 1 to string 32 respectively.
drops below 0.5 A.
532-547, 564- PV Reverse Con-
ceding causes are ruled out and the alarm
579 nection Alarm
persists.
83

Check whether the voltage and current of the in-
verter is abnormal to determine the cause of the
alarm.
1. Check whether the corresponding module is
sheltered. If so, remove the shelter and ensure
module cleanness.
2. Check whether the battery board wiring is
loose, if so, make it reliably connected.
548-563, 580- PV Abnormal
3. Check if the DC fuse is damaged. If so, replace
595 Alarm
the fuse.
persists.
Generally, the inverter will resume operation
when the internal or module temperature returns
to normal. If the fault persists:
1. Check whether the ambient temperature of the
inverter is too high;
2. Check whether the inverter is in a well-venti-
Excessively High
lated place;
37 Ambient
3. Check whether the inverter is exposed to di-
Temperature
rect sunlight. Shield it if so;
4. Check whether the fan is running properly. Re-
place the fan if not;
5. Contact Sungrow Power Customer Service if
the fault is due to other causes and the fault
persists.
Excessively Low Stop and disconnect the inverter. Restart the in-
43 Ambient verter when the ambient temperature rises within
Temperature the operation temperature range.
84

Wait for the inverter to return to normal. If the
fault occurs repeatedly:
1. Check whether the ISO resistance protection
value is excessively high via the app or the LCD,
and ensure that it complies with the local
regulations.
2. Check the resistance to ground of the string
and DC cable. Take corrective measures in case
of short circuit or damaged insulation layer.
Low System Insu-
39 3. If the cable is normal and the fault occurs on
lation Resistance
rainy days, check it again when the weather turns
fine.
4. If there are batteries, check whether battery
cables are damaged and whether terminals are
loose or in poor contact. If so, replace the dam-
aged cable and secure terminals to ensure a reli-
able connection.
1. Check whether the AC cable is correctly
connected.
Grounding Cable 2. Check whether the insulation between the
106
Fault ground cable and the live wire is normal.
1. Disconnect the DC power supply, and check
whether any DC cable is damaged, the connec-
tion terminal or fuse is loose or there is a weak
contact. If so, replace the damaged cable, fasten
the terminal or fuse, and replace the burnt
component.
88 Electric Arc Fault
2. After performing step 1, reconnect the DC
power supply, and clear the electric arc fault via
the App or the LCD, after that the inverter will re-
turn to normal.
3. Contact Sungrow Customer Service if the fault
persists.
85

1. Check if the meter is wrongly connected.
2. Check if the input and output wiring of the me-
Reverse Connec-
ter is reversed.
84 tion Alarm of the
3. If the existing system is enabled, please check
Meter/CT
if the rated power setting of the existing inverter
is correct.
1. Check whether the communication cable and
the terminals are abnormal. If so, correct them to
ensure reliable connection.
Meter Communi-
2. Reconnect the communication cable of the
514 cation Abnormal
meter.
Alarm
persists.
1. Check whether the output port is connected to
actual grid. Disconnect it from the grid if so.
323 Grid Confrontation
1. Check whether the communication cable and
the terminals are abnormal. If so, correct them to
ensure reliable connection.
Inverter Parallel
2. Reconnect the communication cable of the
75 Communication
meter.
Alarm
persists.
86

7, 11, 16, 19–
25, 30–34, 36,
38, 40–42, 44–
50, 52–58, 60–
69, 85, 87, 92,
1. Wait for the inverter to return to normal.
93, 100–105,
2. Disconnect the AC and DC switches, and dis-
107–114, 116–
connect the battery side switches if there are bat-
124, 200–211,
System Fault teries. Close the AC and DC switches in turn 15
248–255, 300–
minutes later and restart the system.
322, 324–328,
401–412, 600–
603, 605, 608,
612, 616, 620,
622–624, 800,
802, 804, 807,
1096–1122
59, 70–74, 76– 1. The inverter can continue running.
83, 89, 216– 2. Check whether the related wiring and terminal
218, 220–233, are abnormal, check whether there are any for-
432–434, 500– eign materials or other environmental abnormal-
System Alarm
513, 515–518, ities, and take corresponding corrective
635–638, 900, measures when necessary.
901, 910, 911, 3. If the fault persists, please contact Sungrow
996 Power Customer Service.
MPPT Reverse drops below 0.5 A.
264-283
Connection 2. Contact Sungrow Customer Service if the pre-
87

1. The inverter can continue running.
2. Check whether the related wiring and termi-
nals are abnormal, check whether there are any
Boost Capacitor foreign materials or other environmental abnor-
332-363
Overvoltage Alarm malities, and take corresponding corrective
measures when necessary.
If the fault persists, please contact Sungrow
Power Customer Service.
1. Disconnect the AC and DC switches, and dis-
connect the battery side switches if there are bat-
Boost Capacitor teries. Close the AC and DC switches in turn 15
364-395
Overvoltage Fault minutes later and restart the system.
2. If the fault persists, please contact Sungrow
Power Customer Service.
1. Check whether the number of PV modules of
the corresponding string is less than other strings.
If so, disconnect the DC switch and adjust the PV
module configuration when the string current
drops below 0.5 A.
String Current 2. Check whether the PV module is shaded;
1548-1579
Reflux 3. Disconnect the DC switch to check whether
the open circuit voltage is normal when the string
current drops below 0.5 A. If so, check the wiring
and configuration of the PV module,
4. Check whether the orientation of the PV mod-
ule is abnormal.
88

1. When the fault occurs, it is forbidden to directly
disconnect the DC switch and unplug PV termi-
nals when the direct current is greater than 0.5 A;
2. Wait until the direct current of the inverter falls
below 0.5 A, then disconnect the DC switch and
1600 - 1615, PV Grounding
unplug the faulty strings;
1632 - 1655 Fault
3. Do not reinsert the faulty strings before the
grounding fault is cleared;
4. If the fault is not caused by the foregoing rea-
sons and still exists, contact Sungrow Customer
Service.
1. It is prohibited to disconnect the DC switch
when the DC current is greater than 0.5 A when
the fault occurs.
System Hardware
1616 2. Disconnect the DC switch only when the inver-
Fault
ter DC side current drops below 0.5 A.
3. It is prohibited to power up the inverter again.
Please contact Sungrow Customer Service.
9.2 Maintenance
9.2.1 Maintenance Notices
Risk of inverter damage or personal injury due to incorrect service!
• Be sure to use special insulation tools when perform high-voltage operations.
• Before any service work, first disconnect the grid-side AC circuit breaker and
check the inverter status. If the inverter indicator is off, please wait until night to
disconnect the DC switch. If the inverter indicator is on, directly disconnect the
DC switch.
• Turn the DC switch from ON to OFF, the DC switch can be locked here. （For
countries “AU” and “NZ”）
erators who wear protective equipment operate and maintain the inverter
• Even if the inverter is shut down, it may still be hot and cause burns. Wear pro-
tective gloves before operating the inverter after it cools down.
89
To prevent misuse or accidents caused by unrelated personnel: Post prominent

warning signs or demarcate safety warning areas around the inverter to prevent
accidents caused by misuse.
Restart the inverter only after removing the fault that impairs safety performance.
As the inverter contains no component parts that can be maintained, never open
the enclosure, or replace any internal components.
To avoid the risk of electric shock, do not perform any other maintenance opera-
tions beyond this manual. If necessary, contact your distributor first. If the problem
persists, contact SUNGROW. Otherwise, the losses caused is not covered by the
warranty.
Touching the PCB or other static sensitive components may cause damage to the
device.
• Do not touch the circuit board unnecessarily.
• Observe the regulations to protect against electrostatic and wear an anti-static

wrist strap.
9.2.2 Routine Maintenance

Item Method Period
Check whether the air outlet and heat
sink are blocked by dust and other
Six months to a year
objects.
Device clean (depend on the dust con-
Check if the air inlet and outlet are
tents in air)
normal. Clean the air inlet and outlet,
if necessary.
Check whether there is a fan alarm on
the App.
Check whether there is any abnormal
Fans Once a year
noise when the fan is rotating.
Clean or replace the fans if necessary
(see the following section).
90
Item Method Period

Check whether the cable entry is in-
sufficiently sealed or the gap is exces-
Cable entry Once a year
sively large, and reseal the entry
when necessary.
Check whether cables are loose or fall
off.
Electrical
Check whether the cable is damaged, Six months to a year
connection
especially the part in contact with the
metal enclosure.
9.2.3 Cleaning Air Inlet and Outlet
A significant amount of heat is generated when the inverter is working.

In order to maintain good ventilation, please check to make sure the air inlet and outlet are
not blocked.
Clean the air inlet and outlet with soft brush or vacuum cleaner if necessary.
9.2.4 Fan Maintenance
• Power off the inverter and disconnect it from all power supplies before main-
taining fans.
erators who wear protective equipment operate and maintain the inverter.
• Fan maintenance must be performed by professionals.
Fans inside the inverter are used to cool the inverter during operation. If the fans do not op-
erate normally, the inverter may not be cooled down and inverter efficiency may decrease.
Therefore, it is necessary to clean dirty fans and replace the broken fans in a timeiy manner.
The operation procedure is as follows:
step 1 Stop the inverter (see 8.1 Disconnecting the Inverter).
step 2 Loosen the screw on the sealing plate of the fan module.
91
step 3 Press the tab of the latch hook, unplug the cable connection joint outwards, and loosen the
screw on the fan holder.
step 4 Pull out the fan module, clean the fans with soft brush or vacuum cleaner, and replace them
when necessary.
step 5 Reinstall the fan back to the inverter in reverse order and restart the inverter.
- - End
92
10 Appendix
10.1 Technical Data

Parameters SG30CX(1) SG30CX(2) SG33CX
Input (DC)
Recommended max. PV in-
45kW / /
put power
Max. PV input voltage 1100V(3)
Min. PV input voltage /
200V / 250V
Start-up input voltage
Nominal PV input voltage 585V
MPP voltage range 200 – 1000V
No. of independent MPP
3
inputs
No. of PV strings per MPPT 2
Max. PV input current 78 A (26 A / 26 A / 26 A)
Max. DC short-circuit
120 A (40 A / 40 A / 40 A)
current
Output (AC)
33 kVA @45 ℃,
400Vac / 36.3 kVA
@ 40 ℃, 400Vac
AC output power 29.9kVA 29.9kVA 33 KVA@50℃,
415Vac / 36.3
KVA@45℃,
415Vac
Rated AC output apparent
29.9 kVA / /
power
Max. AC output current 48.15A 43.16A 55.2A
Nominal AC voltage 3 / N / PE，230 / 400V
AC voltage range 312 – 528V
Nominal grid frequency /
50 Hz / 45 – 55 Hz, 60 Hz / 55 – 65 Hz
Grid frequency range
Harmonic (THD) < 3 % (at nominal power)
93
10 Appendix User Manual

Power factor at nominal
power / Adjustable power > 0.99 / 0.8 leading – 0.8 lagging
factor
Feed-in phases / AC
3/3
connection
Efficiency
Max. efficiency / European
98.6% / 98.3%
efficiency
Protection
DC
Yes
reverse polarity protection
AC short circuit protection Yes
Leakage current protection Yes
Grid monitoring Yes
Ground fault monitoring Yes
DC switch Yes
AC switch No
PV string monitoring Yes
Q at night function Yes
PID recovery function Yes
DC Terminal Protective
Yes / /
Cover
Arc fault circuit interrupter
/ / Opt.
(AFCI)
DC Type II (Type I
DC Type II / AC DC Type II / AC
Surge protection + II Opt.) / AC Type
Type II Type II
II
General Data
Dimensions (W*H*D) 702×595×310mm
Weight 50kg
Topology Transformerless
Degree of protection IP66
Night power consumption ≤2 W
Operating ambient tempera-
-30 to 60 ℃ (> 45 ℃ derating)
ture range
Allowable relative humidity
0 - 100%
range
Cooling method Smart forced air cooling
94
User Manual 10 Appendix

Max. operating altitude 4000 m (> 3000 m derating)
Display LED, Bluetooth + App
RS485 / WLAN / RS485 / Option- RS485 / Optional:
Communication Optional: al: WLAN , WLAN, Ethernet
Ethernet Ethernet
DC connection type MC4 (Max. 6 mm2)
AC connection type OT or DT terminal (Max.70 mm2)
Q at night function, LVRT, HVRT, active & reactive power
Grid Support
control and power ramp rate control
Country of manufacture China / /
(1) For Countries “AU” and “NZ”.

(2) For other countries.
(3) The inverter enters the standby state when the input voltage ranges between 1000V and
1100V.
Parameters SG40CX SG50CX(1) SG50CX(2)

Input (DC)
/ 76kW /
put power
200V / 250V
4 5 5
inputs
130A(26 A / 26
Max. PV input current 104A A / 26 A / 26 A / 130A
26 A)
200A(40 A / 40
Max. DC short-circuit
160A A / 40 A / 40 A / 200A
current
40 A)
Output (AC)
95

40 kVA @45 ℃,
400Vac / 44 kVA 50 kVA @45 ℃,
@ 40 ℃, 400Vac / 55kVA @
400Vac 40 40 ℃, 400Vac
AC output power 50kVA
KVA@50℃, 50KVA@50℃,
415Vac / 44 415Vac / 55kVA @
KVA@45℃, 45 ℃,415Vac
415Vac
/ 50kVA /
power
Max. AC output current 66.9A 80.5A 83.6A
50 Hz / 45 – 55 Hz, 60 Hz / 55 – 65 Hz
factor
Feed-in phases / AC
3/3
connection
Efficiency
98.6% / 98.3% 98.7% / 98.4% 98.7% / 98.4%
efficiency
Protection
DC
Yes
Grid monitoring Yes
DC switch Yes
AC switch No
/ Yes /
Cover
96

Opt. / Opt.
(AFCI)
DC Type II (Type
DC Type II / AC DC Type II (Type I +
Surge protection I + II Opt.) / AC
Type II II Opt.) / AC Type II
Type II
General Data
Dimensions (W*H*D) 782×645×310mm
Weight 58kg 62kg 62kg
-30 to 60 ℃ (> 45 ℃ derating)
ture range
0 - 100%
range
RS485 / Option- RS485 / WLAN RS485 / Optional:
Communication al: WLAN, / Optional: WLAN, Ethernet
Ethernet Ethernet
Grid Support
Country of manufacture / China /
(1) For Countries “AU” and “NZ”.

(2) For other countries.
(3) The inverter enters the standby state when the input voltage ranges between 1000V and
1100V.
Parameters SG30CX-NI SG50CX-NI

Input (DC)
45kW 76kW
put power
200V / 250V
97

3 5
inputs
130A(26 A / 26 A / 26 A / 26
Max. PV input current 78 A (26 A / 26 A / 26 A)
A / 26 A)
Max. DC short-circuit 200A(40 A / 40 A / 40 A / 40
120 A (40 A / 40 A / 40 A)
current A / 40 A)
Output (AC)
AC output power 29.9kVA 50kVA
29.9 kVA 50kVA
power
Max. AC output current 48.15A 80.5A
50 Hz / 45 – 55 Hz, 60 Hz / 55 – 65 Hz
factor
Feed-in phases / AC
3/3
connection
Efficiency
98.6% / 98.3% 98.7% / 98.4%
efficiency
Protection
DC
Yes
Grid monitoring Yes
DC switch No(2)
AC switch No
98

Yes
Cover
/
(AFCI)
Surge protection DC Type II / AC Type II
General Data
Dimensions (W*H*D) 702×595×310mm 782×645×310mm
Weight 50kg 62kg
-30 to 60 ℃ (> 45 ℃ derating)
ture range
0 - 100%
range
Communication RS485 / WLAN / Optional: Ethernet
Grid Support
Country of manufacture China
(1) The inverter enters the standby state when the input voltage ranges between1,000V and
1,100V. If the maximum DC voltage in the system can exceed 1000V, the MC4 connectors
included in the scope of delivery must not be used. In this case MC 4 Evo2 connectors must
be used.
(2) For inverters without a DC switch, it is necessary to prepare an external DC switch ac-
cording to AS 60947.3.
10.2 Wring Distance of DI Dry Contact
The wiring distance between DI dry contact terminals must meet the requirements in the ta-
ble below. The wiring distance L is the total length of all DI signal cables.
99
LK refers to the cable length in one direction between the DI dry contact terminal of the kth in-
verter and the corresponding terminal of the (k-1)th inverter.
table 10-1 Correspondence Between Inverter Quantity and Maximum Wiring Distance
Number of Maximum Wiring Distance(unit:m)
Inverter 16AWG / 1.31mm2 17AWG / 1.026mm2
1 13030 10552
2 6515 5276
3 4343 3517
4 3258 2638
5 2606 2110
6 2172 1759
7 1861 1507
8 1629 1319
9 1448 1172
10 1303 1055
11 1185 959
12 1086 879
13 1002 812
14 931 754
15 869 703
16 814 660
17 766 621
18 724 586
19 686 555
20 652 528
21 620 502
22 592 480
23 567 459
24 543 440
25 521 422
100
In case the specification of the cable used is not included in the table above, when
there is only one inverter, ensure that the line impedance of the input node is less
than 300Ω; and when there are multiple inverters connected in the daisy chain, en-
sure that the impedance is less than 300Ω/number of inverter.
10.3 Quality Assurance
When product faults occur during the warranty period, SUNGROW will provide free service
or replace the product with a new one.
Evidence
During the warranty period, the customer shall provide the product purchase invoice and
date. In addition, the trademark on the product shall be undamaged and legible. Otherwise,
SUNGROW has the right to refuse to honor the quality guarantee.
Conditions
• After replacement, unqualified products shall be processed by SUNGROW.
• The customer shall give SUNGROW a reasonable period to repair the faulty device.
Exclusion of Liability
In the following circumstances, SUNGROW has the right to refuse to honor the quality
guarantee:
• The free warranty period for the whole machine/components has expired.
• The device is damaged during transport.
• The device is incorrectly installed, refitted, or used.
• The device operates in harsh conditions beyond those described in this manual.
• The fault or damage is caused by installation, repairs, modification, or disassembly per-

formed by a service provider or personnel not from SUNGROW.
• The fault or damage is caused by the use of non-standard or non-SUNGROW compo-

nents or software.
• The installation and use range are beyond stipulations of relevant international
standards.
• The damage is caused by unexpected natural factors.
For faulty products in any of above cases, if the customer requests maintenance, paid main-
tenance service may be provided based on the judgment of SUNGROW.
10.4 Contact Information
In case of questions about this product, please contact us.
101
We need the following information to provide you the best assistance:
• Model of the device
• Serial number of the device
• Fault code/name
• Brief description of the problem
For detailed contact information, please visit: https://en.sungrowpower.com/contactUS.
102
Sungrow Power Supply Co., Ltd.
www.sungrowpower.com

SG30 33 40 50CX-UEN-Ver21-202211 PDF

Uploaded by

Copyright:

Available Formats

SG30 33 40 50CX-UEN-Ver21-202211 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SG30 33 40 50CX-UEN-Ver21-202211 PDF

Uploaded by

Copyright:

Available Formats

User Manual

All Rights Reserved

• It is prohibited to use data contained in firmware or software developed by SUNGROW,

• It is prohibited to perform reverse engineering, cracking, or any other operations that

It will be referred to as "inverter" hereinafter unless otherwise specified.

“NOTE” indicates additional information, emphasized contents or tips that may be

• Injury or death to the operator or a third party.

• Damage to the product and other properties.

1.1 Unpacking and Inspection

Check all safety signs, warning labels and nameplates on devices.

1.2 Installation Safety

Make sure there is no electrical connection before installation.

Improper installation may cause personal injury!

• If the product supports hoisting transport and is hoisted by hoisting tools, no

1.3 Electrical Connection Safety

• Operators must wear proper personal protective equipment during electrical

• Respect all safety instructions listed in relevant documents about PV strings.

Danger to life due to a high voltage inside the inverter!

• Be sure to use special insulation tools during cable connections.

• Electrical connection must be performed by professionals.

1.4 Operation Safety

• Do not touch its enclosure.

• It is strictly forbidden to plug and unplug any connector on the inverter.

1.5 Maintenance Safety

Risk of inverter damage or personal injury due to incorrect service!

To prevent misuse or accidents caused by unrelated personnel, post prominent

1.6 Disposal Safety

2.1 System Introduction

The inverter is a transformerless 3-phase PV grid-connected inverter. As an integral compo-

figure 2-1 Inverter Application in PV Power System

The inverter applies only to the scenarios described in this manual.

Item Description Note

The following figure shows the common grid configurations.

2.2 Product Introduction

figure 2-2 Inverter Appearance

No. Name Description

figure 2-3 Product Dimensions(in mm)

Type Dimensions (W*H*D) Weight

2.3 Symbols on Product

Do not dispose of the inverter together with household waste.

TÜV mark of conformity.

Regulatory compliance mark.

The inverter does not have a transformer.

CGC-SOLAR mark of conformity.

Danger to life due to high voltages!

Read the user manual before maintenance!

2.4 LED Indicator

table 2-1 LED Indicator State Description

LED Color State Definition

A fault occurs and the device cannot connect to the

The Bluetooth connection is established, data commu-

OFF Both the AC and DC sides are powered down.

The DC switch is used to disconnect the DC current safely whenever necessary.

Turn the DC switches to the ON position before restarting the inverter.

2.6 Circuit Diagram

The following figure shows the main circuit of the inverter.

figure 2-4 Circuit Diagram

2.7 Function Description

The inverter is equipped with the following functions:

Type Dimensions (WHD) Weight