OPERATING MANUAL

DC AMPERE METER
AV-14DA,24DA,34DA

AV 14DA

 AV 24DA




AV 34DA

AV-14DA AV-24DA AV-34DA

96 X 96mm 72 X 72mm 48 X 96mm

Technical Specification

Model AV 14DA AV 24DA AV 34DA

Display 4 Digit, Single Display

Size(HXWXD) 96 X 96 X 50 mm 72 X 72 X 85 mm 48 X 96 X 55 mm
Panel Cutout 92 X 92 mm 68 X 68 mm 44 X 92 mm
Input 75mV DC
Range 1 TO 9999
Power Supply 230V AC, 50 Hz, Approx 4VA
Protection Level IP-65(Front side) AS per IS/IEC 60529:2001
(As per request)
Operating Relative Up to 95% RH Non Condensing
Temperature 0°C To 55°C Humidity

NOTE : Every Time, When Instrument is turned on following parameter will be displayed.

(POWER ON)

 (Previously selected High range

value Display for 2 Second)


 (Process Value)

AV-14DA/24DA/34DA Page - 1 www.multispanindia.com

 Procedure for range selection

(POWER ON)

 (Press SET & key to set digit value )

Press SET
key
 (Change by & key )
Press SET
key
 (Enter“37” Password for parameter Setting)

Press SET
key
 (Decimal Point)
Press SET
key
 (Change by & key )
Press SET
key
 (High Range)
Press SET
key
 (Set by & key)
Press SET
key


Press SET key Save & Exit

AV-14DA/24DA/34DA Page - 2 www.multispanindia.com

 Connection Diagram

AV-14DA

Range: Selectable up to
9999 Amp DC CAT III

230V AC
!
50Hz,4VA
Input
75mV DC
L
1
N
2 3 4 5 6 7 8
-
9
+
10

AV-24DA

1 L 230V AC Input + 8
2 N
50Hz,4VA

!
75mV DC
- 9
3 10
4 11
12
5
6 13
7 14

AV-34DA

230V AC
50Hz,4VA Range: Selectable up to
! 9999A DC CAT III Input
75mV DC
L N - +
1 2 3 4 5 6 7 8 9 10

AV-14DA/24DA/34DA Page - 3 www.multispanindia.com

 Safety Precautions
All safety related codifications, symbols and instructions that appear in this operating manual
or on the equipment must be strictly followed to ensure the safety of the operating personnel as
well as the instrument.
If all the equipment is not handled in a manner specified by the manufacturer, it might impair the
protection provided by the equipment .
=> Read complete instructions prior to installation and operation of the unit.
WARNING : Risk of electric shock.
Warning Guidelines
1) To prevent the risk of electric shock power supply to the equipment must be kept OFF while doing the wiring
arrangement. Do not touch the terminals while power is being supplied.
2) To reduce electro magnetic interference, use wire with adequate rating and twists of the same of equal size shall
be made with shortest connection.
2
3) Cable used for connection to power source, must have a cross section of 1mm or greater. These wires
should have insulations capacity made of at least 1.5kV.
4) A better anti-noise effect can be expected by using standard power supply cable for the instrument.

Installation Guidelines
1) This equipment, being built-in-type, normally becomes a part of main control panel and such in case the
terminals do not remain accessible to the end user after installation and internal wiring.
2) Do not allow pieces of metal, wire clippings, or fine metallic fillings from installation to enter the product
or else it may lead to a safety hazard that may in turn endanger life or cause electrical shock to the operator.
3) Circuit breaker or mains switch must be installed between power source and supply terminal to
facilitate power ‘ON’ or ‘OFF’ function. However this mains switch or circuit breaker must be
installed at convenient place normally accessible to the operator.
4) Use and store the instrument within the specified ambient temperature and humidity ranges as
mentioned in this manual.
Mechanical Installation
B D E 136mm - 5.35 inches

AV 14DA
F


MODEL A B C D E F
120mm - 4.72 inches

A C
DIMENSIONS 96mm 96mm 92mm 92mm 3mm 50mm

D E F 95mm - 3.75 inches

B
AV 24DA

 MODEL A B C D E F
85mm - 3.34 inches

A C
DIMENSIONS 72mm 72mm 68mm 68mm 3mm 85mm

B D
E F 136mm - 5.35 inches


MODEL A B C D E F
60mm - 2.36 inches

A C
AV 34DA
DIMENSIONS 48mm 96mm 44mm 92mm 4.5mm 66mm

1) Prepare the panel cutout with proper dimensions as show above.

2) Fit the unit into the panel with the help of clamp given.
3) The equipment in its installed state must not come in close proximity to any heating source,
caustic vapors, oils steam, or other unwanted process by products.
4) Use the specified size of crimp terminal (M3.5 screws) to wire the terminal block. Tightening the
screws on the terminal block using the tightening torque of the range of 1.2 N.m.
5) Do not connect anything to unused terminals.

Maintenance
1) The equipment should be cleaned regularly to avoid blockage of ventilating parts.
2) Clean the equipment with a clean soft cloth. Do not use isopropyl alcohol or any other cleaning agent.
3) Fusible resistor must not be replaced by operator.

AV-14DA/24DA/34DA Page - 4 www.multispanindia.com