LT Cseries2

1/2
No.7136-0664 July, 2020

Instruction manual
Power line classⅡSPD for machine protection
(Type：LT-C12G801W，LT-C14G801W，LT-C32G801W，
LT-C34G801W，LT-C35G102W)
Please read the instructions before installing the product, as this instruction manual explains how to use
the SPD effectively and safely.
The SPD conforms to the induced lightning current test specified in classⅡof IEC61643-11, classⅡof
EN61643-11, Type2CA of UL1449, Type4-2 of CSA C22.2No269. This SPD can operate normally against
induced lightning and does not withstand direct lightning surges (including adjacent lightning) that exceed
the value described in the specification and it may not protect the equipment connected. Please confirm the
detailed specification, size, etc. using the brochure or data sheet.
1.△Safety instruction
！
1）Instruction for use

a) It is exceptionally difficult to predict the energy involved with lightning, since it is a natural
phenomenon. In the event of direct lightning strike exceeding the specification or if there are
multiple induced lightning currents in a short period of time, the SPD may deteriorate, short
circuit and in the worst case fail. In the unlikely event of failure of the SPD, and during the
inspection of the SPD, follow below instructions to protect other equipment.
①The SPD should be installed in a metal enclosure. (Recommended example：Metal case with
transparent window)
②Install the SPD as shown in Fig.1.
Single phase circuit 3phase circuit 3phase circuit
Yconnection Δconnection
Equipment Equipment Equipment
L L L L L L L L
E E E
SPD for machine SPD for machine SPD for machine

protection protection protection
Max. continuous Max. continuous Max. continuous

Type Type Type operating voltage
operating voltage operating voltage
LT-C12G801W 275V LT-C32G801W 275V LT-C32G801W 275V
L-E : 280V LT-C34G801W 480V LT-C34G801W 280V
LT-C14G801W
L-L : 480V LT-C35G102W 550V LT-C35G102W 320V
Fig.1 SPD installation circuit
b) Electric circuit condition

①Do not install the SPD on circuits where it is subjected to voltages above specified Maximum
Continuous Operating Voltage Uc.
②Do not use the SPD above the peak value of MCOV (Uc×√2), if DC or AC voltage has incomplete wave
shape.
③Do not use the SPD in the circuits that are subjected to frequent current surges with a very short
interval between them.
c) Environmental condition
① Do not expose the SPD to high temperature such as direct sunshine or install adjacent to hot object.
(Application temperature : －20℃ to +70℃)
② Do not expose the SPD to adverse environmental conditions such as rain, wind, steam, dust, and
salty air.
③ Do not expose the SPD to acid, alkali, corrosion gas, solvent, oil, dust, and salt.
④ Handle the SPD carefully to prevent mechanical shock (e.g. drop) or vibration, as this may cause
cracking of its plastic housing.
⑤ Do not pull the wires strongly and do not use the SPD in the condition that its wires are always
pulling.
2/2
2）Instruction for regular maintenance
When the maintenance, the SPD should be disconnected from the circuit by switching off the main
circuit isolating switch on the electric input side of the SPD, or power off the machine. If insulation
withstand voltage test for the machine which the SPD is installed in is conducted, remove the earth
wire of the SPD from the earth terminal.
3）Countermeasure against the failure of the SPD and unlikely event of the operation of power switch
and so on
a) Personnel without authorization to work on electrical circuitry – immediately contact the relevant
authorized personnel but do not touch the SPD.
b) Authorized person
During inspection of the SPD, it should be confirmed the SPD is disconnected from the circuit by
switching off the main power switch on the electric input side of the SPD, to protect against an
electric shock.
Refer to “3 item, regular maintenance” when checking the inspection contents.
2. Installation method
Only authorized person should install the SPD and conduct the wiring construction.
1） Installation method
Use the installation hole of φ4.5 on the SPD and fix it by M4 screw.
2） Wiring
・SPD should be wired by connecting crimp terminal to the wire of the SPD.
・Cut off the wire of the SPD to conduct wiring easily.
But during and after wiring, pulled power on the wire (More than 40N) Indicator
should not be stable.
3.Regular maintenance
When maintenance, follow the below caution items.
（Ref. 1.Safety instruction, 2)Instruction for regular maintenance）
＜SPD inspection method＞
φ4.5
Replace the SPD if it is under below conditions Installation hole
○Appearance check
・If the indicator of the SPD turns red, SPD deteriorates.
Replace the SPD.
・If it is noted that the plastic housing has changed color or shape, Fig.2 Insulation hole, Indicator
replace the SPD.
○Measurement of insulation resistance
・Insulation resistance between the wire on L side and E side should be measured. If the insulation
resistance does not meet “more than 10MΩ by 500V insulation tester”, replace the SPD.
4.Caution item in accordance with UL standard

“Type 4-2 SPDs shall only be installed by a qualified person.”
“Les dispositifs de protection contre les surtensions de type 4-2 ne doivent être installés que par une
personne qualifiée.”
“For Use on circuits delivering up to 5,000 rms Amps.”

“Prévu pour des circuits dont l’intensité est égale ou inférieure à 5,000_A eff.”
“No serviceable parts.”

“Aucune pièce remplaçable ou reparable.”
Company
OTOWA ELECTRIC CO.,Ltd. (e-mail : overseas@otowadenki.co.jp)
Sales head office : 5-6-20, Shioe, Amagasaki-city, Hyogo Pref. 〒661-0976, JAPAN

LT Cseries2

Uploaded by

Copyright:

Available Formats

LT Cseries2

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LT Cseries2

Uploaded by

Copyright:

Available Formats

1/2

No.7136-0664 July, 2020

1）Instruction for use

Equipment Equipment Equipment

SPD for machine SPD for machine SPD for machine

Max. continuous Max. continuous Max. continuous

Fig.1 SPD installation circuit

b) Electric circuit condition

4.Caution item in accordance with UL standard

“For Use on circuits delivering up to 5,000 rms Amps.”

“No serviceable parts.”

You might also like