Diffused Silicon Pressure Sensor

XDB102-3 Series

Descriptions
XDB102-3 series diffused silicon pressure sensor cores use high stability diffused silicon chip, the measured medium pressure can
be transferred to silicon chips through the diaphragm and silicon oil transfer to the diffusion of silicon chips, the use of diffused
silicon piezo-resistive effect principle to achieve the purpose of measuring the size of liquid, gas pressure.

Features
 CE conformity
 Measuring Range: -100kPa…0kPa~20kPa…3.5MPa
 Imported chip, Laser trimming
 SS 316L
 φ19mm×5.55mm
 Provide OEM, flexible customization

Applications
 Industrial process control
 Gas, liquid and vapor pressure detection
 Level measurement

Specification
Structure Condition
Diaphragm material SS 316L
Housing material SS 316L
Pin Wire Gold-plated karaf /100mm silicone rubber wire
Back pressure tube SS 316L (gauge and negative pressure only)
Seal ring Nitrile rubber
Electrical Condition
Power supply ≤2.0mADC
Impedance input 2.5~5kΩ
Impedance output 2.5kΩ～5kΩ
Response (10%～90%):<1ms
Insulation resistance 100MΩ,100V DC
Overpressure 2times FS, ( 0C/0B/0A/02 5times FS)
Environment Condition
Media applicability Fluid that is not corrosive to stainless steel and nitrile rubber
Shock No change at 10gRMS，(20～2000)Hz
Impact 100g，11ms
Position effects Deviate 90° from any direction, zero change≤±0.05%FS
Basic Condition
Environment temperature (25±1)℃
Humidity (50%±10%) RH
Atmospheric pressure (86~106) KPa
Power supply (1.5±0.0015) mA DC
All tests are in accordance with relevant national standards, including GB / T2423-2008, GB / T8170-2008, GJB150.17A-2009,
etc., and also comply with the Company's "Pressure Sensor Enterprise Standards" provisions of the relevant content.

XIDIBEI Sensor & Control Page 1- 3

 Diffused Silicon Pressure Sensor

Parameters

Item Min. Typ. Max. Units

Linearity ±0.15 ±0.25 %FS,BFSL
Repeatability ±0.05 ±0.075 %FS
Hysteresis ±0.05 ±0.075 %FS
Zero output ±2.0 mV DC
FS output 45 100 mV DC
Compensated temp. range 0～70 ℃
Working temp. range -40～125 ℃
Storage temp. range -55～150 ℃(no Sealing ring)
Zero temp. error ±0.75 ±1.0 %FS,@ 25℃
Full temp. error ±0.75 ±1.0 %FS,@ 25℃
Long term stability error ±0.2 %FS/year
Note：1. The above performance indicators are tested under the benchmark conditions.
2. The temperature range for temperature drift test is the compensation temperature range.

Dimension (unit: mm)

Electrical connection

Pin Electrical connection Wire color

4 +OUT Red
10 －OUT Blue
11 －IN Yellow
12 +IN Black

XIDIBEI Sensor & Control Page 2-3

 Diffused Silicon Pressure Sensor

Ordering information

XDB102-3
Measurement Pressure Measurement Pressure
Range code Range code
range type range type
0B 0～20kPa G 08 0～350kPa G/A
0A 0～35kPa G 09 0～700kPa G/A
02 0～70kPa G 10 0～1MPa G/A
03 0～100kPa G/A 12 0～2MPa G/A
07 0～200kPa G/A 13 0～3.5MPa G/A
Code Pressure Type
G Gauge pressure
A Absolute pressure
Code Electrical connection
1 Gold-plated kovar pin
2 100mm Silicone rubber leads
Code Special measurement
Gauge pressure type can be
Y used to measure negative
pressure Note
①

XDB102-3-0B-G-1-Y the whole spec

②

Order notes：
1 To avoid sensor instability, please pay attention to the installation size and installation process to avoid pressing the sensor front
and rear surface.
2 When using a gold-plated cotter pin on a wire, please use a soldering iron below 25W under low temperature soldering
within 3 seconds to avoid heat transfer to the sensor.
3 Because the sensor will be irreparably damaged when welded by improper welding method, if you need the secondary
welding of the sensor, please contact us, we can provide good welding components directly.

SHANGHAI ZHIXIANG SENSOR TECHNOLOGY CO.,LTD

5th Floor,Building 8,Lane 1177,Rongmei Road,Songjiang District,Shanghai, China
Tel: +86 021 37623075 Mob/Wechat/Whatsapp: +86 15000983629
Skype: xingyun1104 E-mail: katherine@xdbsensor.com
Web: www.xdbsensor.com
XIDIBEI Sensor & Control Page 3-3