Lab 7
Lab 7
EEE41L/ETE141L
• Experimentally perform Thevenin’s theorem, Norton’s theorem and Maximum Power theorem
• Perform theoretical calculations.
• Verify the experimental values with theoretical values.
List of Components:
Trainer board
1× 1K
2 × 10KΩ
POT (10K)
Digital Multimeter (DMM)
Connecting Wire
Theory:
Thevenin’sTheorem: Thevenin’s Theorem states that it is possible to simplify any linear
circuit, no matter how complex, to an equivalent circuit with just a single voltage source and
series resistance connected to a load. The Thévenin equivalent circuit consists of a single dc
source referred to as the Thévenin voltage (𝑉𝑇𝐻 )and a single fixed resistor called the Thévenin
resistance (𝑅𝑇𝐻 )
Norton’s Theorem: Norton’s Theorem states that it is possible to simplify any linear circuit,
no matter how complex, to an equivalent circuit with just a single current source (𝐼𝑁 ) and
parallel resistance connected to a load (𝑅𝑁 )
Let’s consider 𝑅2 as the load resistor. To find the voltage and current across this load resistor,
you can follow superposition theorem. Now say your load resistance is subjected to change (i.e
NORTH SOUTH UNIVERSITY
DEPARTMENT OF ELECTRICAL & COMPUTER ENGINEERING
EEE41L/ETE141L
it varies), then each time your resistor value changes, you need to apply superposition theorem
and recalculate the current and voltages. This is time consuming.
Thevenin’s or Norton’s theorem makes this easy by temporarily removing the load resistance
from the original circuit and reducing what’s left to an equivalent circuit:
-Single voltage source and series resistance in case of Thevenin.
- Single current source and parallel resistance in case of Norton.
The load resistance can then be re-connected to this “equivalent circuit” and calculations
carried out as if the whole network were nothing but a simple series circuit:
EEE41L/ETE141L
- Remove the load resistance, calculate the open-circuit voltage at the terminals of the load
resistance.
How to find 𝑹𝑵 ?
- Methods for finding 𝑅𝑁 is same as that for 𝑅𝑇𝐻
How to find 𝑰𝑵 ?
- With voltage sources turned on, replace the load resistance as short circuit. Measure the
short circuit current. This short circuit current is 𝐼𝑁 .
𝑅𝑁 = 𝑅𝑇𝐻
𝐸𝑇𝐻 = 𝐼𝑁 𝑅𝑇𝐻
Maximum Power will be delivered to the load when that load resistance is equal to the
Thevenin/Norton resistance of the network supplying the power. If the load resistance is lower
or higher than the Thevenin/Norton resistance of the source network, its dissipated power will
be less than maximum.
A load impedance that is too high will result in low power output. A load impedance that is too
low will not only result in low power output
𝐼𝐿 = 𝑉𝑇𝐻 / ( 𝑅𝑇𝐻 + 𝑅𝐿 )
= 𝑉𝑇𝐻 / (𝑅𝑇𝐻 + 𝑅𝑇𝐻 )
= 𝑉𝑇𝐻 / 2 𝑅𝑇𝐻
Where, Pmax = 𝐼𝐿 2 𝑅𝐿
=𝑉𝑇𝐻 2 / 4 𝑅𝑇𝐻
NORTH SOUTH UNIVERSITY
DEPARTMENT OF ELECTRICAL & COMPUTER ENGINEERING
EEE41L/ETE141L
Circuit Diagram:
Procedure:
1. Measure the values of resistance using DMM.
2. Construct the Circuit-1
3. Measure 𝑉𝐿 and 𝐼𝐿 of 𝑅𝐿 for circuit 1. Record in Table-2.
4. Remove 𝑅𝐿 from the original circuit and measure the open circuit voltage Vth.
5. Measure the short circuit current 𝐼𝑁 by placing an Ammeter between A and B. In this manner, the
Ammeter will act as a short circuit.
6. Replace the voltage sources with short circuits. With RL removed from the circuit, measure Rth using a
multimeter (place DMM across A and B)
7. Record values in Table-3.
8. Draw the Thevenin and Norton Equivalent circuit in Table-4.
9. Construct the Thevenin equivalent circuit drawn in Table-4, measure 𝐼𝐿 and 𝑉𝐿 . Record readings in Table
2.
10. Now replace the load resistor with a POT, vary the load resistance and for each resistance value measure
𝑉𝐿 . Fill in Table-5
NORTH SOUTH UNIVERSITY
DEPARTMENT OF ELECTRICAL & COMPUTER ENGINEERING
EEE41L/ETE141L
Table 1:
Theoretical R Measured R % Error
10K
1K
Table 2:
Value Measured R % Error
𝑉𝐿 1.25V
𝐼𝐿 1.25mA
Table 3:
Measurement Measured Calculated % Error
𝑉𝑇𝐻
𝐼𝑁
𝑅𝑇𝐻
𝑉𝐿
𝐼𝐿
Table 4:
NORTH SOUTH UNIVERSITY
DEPARTMENT OF ELECTRICAL & COMPUTER ENGINEERING
EEE41L/ETE141L
Table 5:
RL (kΩ) VL (Experimental) PL (Experimental)(mW)
VL2 / RL
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10
Report Questions:
1. Calculate all the theoretical values of Table 2. Show all steps
2. Comparing experimental values to theoretical values, verify Thevenin and Norton
theorem.
3. Prove Thevenin Norton equivalence.
4. In a graph paper, draw𝑃𝐿 vs 𝑅𝐿 .
5. From the graph state the value of 𝑅𝐿 for which maximum power is obtained.
6. Theoretically calculate the maximum power.
7. Verify the maximum power theorem