Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 18 views

    Diode Clippers and Clampers

    Uploaded by

    Praveen K
    This document describes an experiment on diode clippers and clampers. The objective is to design and analyze diode clipping, limiting and clamping circuits and measure voltage limits. Equipment used includes an oscilloscope, function generator, power supply, diode, resistor, capacitor and breadboard. The procedures involve connecting unbiased and biased clipper and clamper circuits and observing input/output waveforms. Students are to design a limiter circuit, verify it, and sketch the output waveform. Results and inferences are to be recorded. Performance is evaluated based on connection/conduction and providing graphs, inferences and results.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Diode Clippers and Clampers

    Uploaded by

    Praveen K
    18 views3 pages
    This document describes an experiment on diode clippers and clampers. The objective is to design and analyze diode clipping, limiting and clamping circuits and measure voltage limits. Equipment used includes an oscilloscope, function generator, power supply, diode, resistor, capacitor and breadboard. The procedures involve connecting unbiased and biased clipper and clamper circuits and observing input/output waveforms. Students are to design a limiter circuit, verify it, and sketch the output waveform. Results and inferences are to be recorded. Performance is evaluated based on connection/conduction and providing graphs, inferences and results.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document describes an experiment on diode clippers and clampers. The objective is to design and analyze diode clipping, limiting and clamping circuits and measure voltage limits. Equipment used includes an oscilloscope, function generator, power supply, diode, resistor, capacitor and breadboard. The procedures involve connecting unbiased and biased clipper and clamper circuits and observing input/output waveforms. Students are to design a limiter circuit, verify it, and sketch the output waveform. Results and inferences are to be recorded. Performance is evaluated based on connection/conduction and providing graphs, inferences and results.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    18 views3 pages

    Diode Clippers and Clampers

    Uploaded by

    Praveen K
    This document describes an experiment on diode clippers and clampers. The objective is to design and analyze diode clipping, limiting and clamping circuits and measure voltage limits. Equipment used includes an oscilloscope, function generator, power supply, diode, resistor, capacitor and breadboard. The procedures involve connecting unbiased and biased clipper and clamper circuits and observing input/output waveforms. Students are to design a limiter circuit, verify it, and sketch the output waveform. Results and inferences are to be recorded. Performance is evaluated based on connection/conduction and providing graphs, inferences and results.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    19ELC101 Electrical and Electronic Circuits

    Exp. No:
    Date :
    DIODE CLIPPERS AND CLAMPERS

    OBJECTIVE

    The purpose of the experiment is to design and analyze diode clipping, limiting and clamping circuits. Also to
    measure the voltage limits of both biased and unbiased clipping circuits and to observe the level shifting in
    clamping circuits.

    EQUIPMENT AND COMPONENTS USED

    1. 50 MHz Dual Channel Digital Storage Oscilloscope


    2. 3 MHz Function Generator
    3. 0-30 V DC dual regulated power supply
    4. Diode 1N4001
    5. Resistor 1 kΩ, ¼W
    6. Electrolytic Capacitor 10µF/25V
    7. Breadboard, Connecting wires, BNC Cables and Probes

    PRACTICE PROCEDURE
    1. Unbiased Clippers
    1. Connect the circuit as shown in Figure 1.

    Figure 1: Unbiased series negative clipper Figure 2: Unbiased series positive clipper

    Figure 3: Unbiased shunt positive clipper Figure 4: Unbiased shunt negative clipper
    2. Apply sine wave of 10Vp-p, 1 kHz from function generator.
    3. Observe the input, output waveforms and its transfer characteristics on Oscilloscope screen.
    Repeat the above steps for Figure 2, Figure 3 and Figure 4.
    19ELC101 Electrical and Electronic Circuits

    Design 1: For the given transfer characteristic curve design a suitable limiter circuit.

    1. Verify the design by applying sine wave of 10Vp-p, 1 kHz from function generator.
    2. Sketch the output waveforms.

    2. Biased Clippers
    1. Connect the circuit as shown in Figure 5.

    Figure 5: Biased Shunt Positive Clipper Figure 6: Biased Series Negative Clipper

    2. Apply sine wave of 10Vp-p, 1 kHz from function generator and 2 V dc from regulated power supply.
    3. Observe the input, output waveforms and its transfer characteristics on Oscilloscope screen.
    Repeat the above steps for Figure 6.

    3. Clampers
    1. Connect the circuit as shown in Figure 7.

    Figure 7: Unbiased Negative Clamper


    2. Apply sine wave of 10Vp-p, 1 kHz from function generator.
    3. Observe the input and output waveforms on Oscilloscope screen.

    RESULT
    19ELC101 Electrical and Electronic Circuits

    INFERENCE

    Components Marks Marks obtained

    1 Connection and Conduction 10

    2 Graph, Inference & Result 10

    You might also like