Ductile-Iron Pressure Pipe: Standard Index of Specifications For

Designation: A 377 – 03
Standard Index of Specifications for

Ductile-Iron Pressure Pipe1
This standard is issued under the fixed designation A 377; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope ANSI/AWWA C105/A21.5, Polyethylene Encasement for

1.1 This index identifies specifications that cover ductile- Ductile-Iron Pipe Systems,2,3
iron pressure pipe suitable for carrying water and other liquids ANSI/AWWA C106/A21.50, Thickness Design of Ductile-
under pressure. Iron Pipe,2,3
ANSI/AWWA C110/A21.10, Ductile-Iron and Gray-Iron
NOTE 1—The text of this standard references notes and footnotes which Fittings,, 3 in. through 48 in. (76 mm through 1219 mm) for
provide explanatory material. These notes and footnotes (excluding those
in tables and figures) shall not be considered as requirements of the
Water,2 3
standard. ANSI/AWWA C111/A21.11, Rubber–Gasket Joints for
Ductile-Iron Pressure Pipe and Fittings,2,3
2. Method of Designation ANSI/AWWA C115/A21.15, Flanged Ductile-Iron Pipe with
2.1 The ASTM designation for these specifications is not Ductile-Iron or Gray-Iron Threaded Flanges,2,3
sufficient to describe the particular items which a purchaser ANSI/AWWA C116/A21.16, Protective Fusion-Bonded Ep-
may desire; therefore, the ANSI designation for the applicable oxy Coatings for the Interior and Exterior Surfaces of Ductile-
American National Standards shown in Section 3 shall be Iron and Gray-Iron Fittings for Water Supply Service,2,3
specified in the inquiry, contract, and order. ANSI/AWWA C153/A21.53, Ductile Iron Compact Fittings
for Water Service,2,3
3. Reference Specifications ANSI/AWWA C600, Installation of Ductile-Iron Water
3.1 Ductile iron pipe furnished in accordance with this Mains and Their Appurtenances, and2,3
index are covered by the following American National Stan- ANSI/AWWA C606, Grooved and Shouldered Joints,2,3
dards: NOTE 2—These specifications were prepared by appropriate subcom-
ANSI/AWWA C151/A21.51, Ductile-Iron Pipe, Centrifu- mittees of American Water Works Association Committee A21 on Ductile
gally Cast for Water,2,3 Iron Pipe and Fittings. This committee was originally organized as an
3.2 Other American National Standards relating to ductile- American National Standards Committee under the sponsorship of ASTM,
iron pipe are the following: American Gas Association (A.G.A), American Water Works Association
(AWWA), and New England Water Works Association (NEWWA). The
ANSI/AWWA C104/A21.4, Cement-Mortar Lining for
current sponsor is AWWA and the present scope of Committee A21
Ductile-Iron Pipe and Fittings for Water,2,3 activity is to develop standards and manuals for ductile-iron and gray-iron
fittings for use with such pipe. After these specifications were approved by
1 Committee A21, they were approved as national standards by ANSI.
This index is under the jurisdiction of ASTM Committee A04 on Iron Castings
and is the direct responsibility of Subcommittee A04.12 on Pipes and Tubes. NOTE 3—The pipes described in these specifications have been de-
Current edition approved Dec. 1, 2003. Published January 2004. Originally signed for trench conditions and internal working pressures in accordance
approved in 1954. Last previous edition approved in 1999 as A 377 – 99. with the method developed by ANSI Standards Committee A21. These
2
Available from the American National Standards Institute, 25 W. 43rd St., 4th methods are described in ANSI/AWWA C150/A21.50, Thickness Design
Floor, New York, NY 10036. of Ductile-Iron Pipe.
3
Available from American Water Works Assoc., 6666 W. Quincy Ave., Denver,
CO 80235.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
A 377 – 03
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org).

Ductile-Iron Pressure Pipe: Standard Index of Specifications For

Uploaded by

Copyright:

Available Formats

Ductile-Iron Pressure Pipe: Standard Index of Specifications For

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ductile-Iron Pressure Pipe: Standard Index of Specifications For

Uploaded by

Copyright:

Available Formats

Designation: A 377 – 03

Standard Index of Specifications for

1. Scope ANSI/AWWA C105/A21.5, Polyethylene Encasement for

You might also like