Problem Statement:

Calculate the blend time for a mixer with one or two impellers

Inputs SI Units US Units

Fluid
Mixing purpose
Degree of agitation
ro Fluid density kg/m3 1000 lb/ft3 62.43
mu Fluid viscosity kg/m-s 0.001 lb/ft-s 0.000672

Tank Geometry
T Diameter m 3 ft 9.84252
H Filled Height m 3.5 ft 11.48294

Impeller
Lowest impeller
Type
D1 Diameter m 2 ft 6.56168
W1 Projected blade height m ft 0
L1 Distance to mounting flange m ft 0
L' Distance to lower bearing m ft 0
C Distance off bottom m ft 0

Second impeller
Type
D2 Diameter m 2 ft 6.56168
W2 Projected blade height m ft 0
L2 Distance to mounting flange m ft 0

N Speed rps 1.42 rps 1.42

Baffles
Number of baffles 4 4
B Baffle width m 0.25 ft 0.82021
Space between baffle and wall m 0.041667 ft 0.136702

Data Lookup and Calculations

Nre Reynolds number 12780000 12778151
gc Conversion factor 1 32.17
NQ Pumping number 0.8 0.8
Q Pumping capacity m3/s 9.088 ft3/s 320.9397

NP Power number - lower impeller 1.3 1.3

P Power W 119112.8 ft-lbf/s 87867.01
hp 159.7582

NP Power number - upper impeller 1.3 1.3

P Power W 119112.8 ft-lbf/s 87867.01

P Total power (assume additive) W 238225.6 ft-lbf/s 175734

hp 319.5164

Mixing zone calculation, Np^(1/3) * Nre 13948001 13945983

Mixing zone Turbulent Turbulent

Theta95 Mixing time, 95% uniformity s 9 9

Desired mixing uniformity 99% 99%

Adjusted mixing time s 14.2 14.2

Volume m3 24.74004 ft3 873.6863

Turnovers, 95% uniformity 3.40 3.40
 Problem Statement:
Calculate power and blend time for a helical ribbon impeller
working in the laminar flow range

Inputs SI Units US Units

Fluid
Mixing purpose Blend
ro Fluid density kg/m3 1000 lb/ft3 62.43
mu Fluid viscosity kg/m-s 100 lb/ft-s 67.20882

Tank Geometry
T Diameter m 3 ft 9.84252
H Filled Height m 3.5 ft 11.48294

Helical Ribbon Geometry

D Diameter m 2.85 ft 9.350394
h Overall height of impeller m 3.5 ft 11.48294
p Pitch (height of one turn) m 0.5 ft 1.64042
w Blade width m 0.285 ft 0.935039
nb Number of blades 2 2

N Speed rps 0.1 rps 0.1

gc Conversion factor 1 32.17

Calculations
c wall clearance m 0.075 ft 0.246063
clearance % of tank diameter 2.5%

Kp Power factor for helical ribbon 807.1066 807.1066

P Power W 18683.81 ft-lb/s 13784.65
hp 25.063

Theta Blend time s 109.5456 109.5456

 Problem Statement:
Estimate the settling velocity of solids in liquid

Inputs SI Units US Units

Solids
Descriptive Spheres Spheres
ps density kg/m3 1,100 lb/ft3 68.53
dn nominal diameter mm 1.0 in 0.039
solids concentration in slurry wt % 55% wt % 55%
Liquid
p density kg/m3 1,000 lb/ft3 62.30
u dynamic viscosity Pa-s 0.0010 cP 1.0
v kinematic viscosity cSt 1.0 cSt 1.0

Other
g gravitational acceleration m/s2 9.80 ft/s2 32.17

Calculations and Results

s specific gravity, solids 1.10 1.10
A formula coefficient A 0.79 0.79
B formula coefficient B 4.61 4.61
S* dimensionless particle parameter 7.83 7.83
W* dimensionless settling velocity 0.72 0.72
terminal settling velocity 2.26 4.46
correction factor 1.85 1.85
ws settling velocity cm/s 4.19 ft/min 8.25

Data
Coefficients for Equation A B
Crushed 0.995 5.211
Natural Sediment 0.954 5.121
Well-Rounded 0.89 4.974
Spheres 0.794 4.606

Correction for Solids Concentration Solids% Factor

0 0.75
 2 0.8
5 0.84
10 0.91
15 1
20 1.1
25 1.2
30 1.3
35 1.42
40 1.55
45 1.7
50 1.85
Result
 Problem Statement:
Calculate the ungassed and gassed power required in an agitated vessel
designed for gas dispersion

Inputs SI Units US Units

Geometry and Parameters
T Tank diameter m 1.30 ft 4.27
D Impeller diameter m 0.52 ft 1.71
Impeller speed rpm 42 rpm 42
NP Power number 5.0 5.0

Liquid
H Liquid height m 3.77 ft 12.37
pL Density, liquid kg/m3 1,000 lb/ft3 62.3
uL Viscosity, liquid Pa-s 0.0010 lb/ft-s 0.00067

Gas
Gas flow rate, actual am3/h 14 acfm 8

Other
g Gravitational acceleration m/s2 9.81 ft/s2 32.17
gc Conversion factor m/s2 1.00 ft/s2 32.17

Calculations
A Tank cross-section m2 1.33 ft2 14.29
V Volume m3 5.00 ft3 176.7
v Superficial gas velocity m/s 0.003 ft/s 0.010

QG Gas flow rate, actual m3/s 0.004 ft3/s 0.14

N Impeller speed rps 0.70 rps 0.70

NFl Gas Flow Number 0.040 0.040

NFr Impeller Froude Number 0.03 0.03

D/T Impeller ratio 0.40 0.40

No discernable action No discernable action

Gas Dispersion Regime Flooding Flooding

Gas Flow number at transition 0.04 0.04

RPD at transition 0.86 0.86
RPD Relative Power Demand 0.85 0.85
Nre Reynolds Number
P Power, ungassed W 65 hp 0.09
pG Power, gassed W 56 hp 0.07

Results
Data

N P Regime
40 49 No discernable actionFlooding
60 152
Regenerate Power
80 360
100 713
120 1,255
140 2,025
160 3,067 Recirculating
180 4,421 Recirculating
200 6,131 Recirculating
220 8,237 Recirculating
240 10,782 Recirculating
260 13,808 Recirculating
280 17,358 Recirculating
300 21,472 Recirculating
320 26,194 Recirculating
340 31,565 Recirculating
360 37,628 Recirculating
380 44,425 Recirculating
400 51,998 Recirculating
420 60,388 Recirculating
440 69,639 Recirculating
460 79,792 Recirculating
No discernable action
 100,000

10,000
Ungassed Power, W

1,000

100

10
10 100
Impeller Speed, rpm
1000
 Problem Statement:
Calculate shaft diameter, torque, and first critical speed, for up to 3 identical impellers on one
shaft. Assume that power is equally distributed among the impellers.

Inputs SI Units US Units

Impellers
D Diameter m 0.660 in
Number of impellers 2
Np Power Number 5.0
fH Hydraulic service factor 1.0
Shaft
Np Speed rps 2.08 rpm
L Shaft length from bottom bearing m 4.22 in
Sb Bearing span, Sb m 0.30 in
Distance between impellers m 2.01 in
Modulus of elasticity N/m2 1.97E+11 psi
Shaft density kg/m3 8,027 lb/in3
Allowable shear stress N/m2 4.10E+07 psi
Allowable tensile stress N/m2 6.90E+07 psi
Mixture
ro Density of mixed liquid kg/m3 1,000 lb/in3
P Power, total W 5,588 hp

Intermediate Calculations
Geometry and Power - impeller-specific
Shaft length, top impeller m NA in
Shaft length, middle impeller m 2.21 in
Shaft length, bottom impeller m 4.22 in
Power per impeller W 2,794 hp
Weight of blades, per impeller
hydrofoil kg 7.35 lb
4-blade PBT kg 5.70 lb

Calculations
Torque N-m 434 in-lbf
Bending moment (maximum) N-m 626 in-lbf

Shaft diameter
Based on shear m 0.05 in
mm 45.57 mm
Based on tensile m 0.05 in
mm 46.79 mm
Selected shaft diameter mm 50 in

Weight of hub
 Read from chart kg 9.0 lb

Total weight for each impeller with hub

hydrofoil kg 16.35 lb
W 4-blade PBT kg 14.70 lb

Equivalent weight, not including shaft

We hydrofoil kg 18.71 lb
4-blade PBT kg 16.81 lb

Natural frequency - First Critical Speed

hydrofoil rps 1.24 rpm
4-blade PBT rps 1.27 rpm

Data
Conversion factors for blade weight formula
hydrofoil 0.14
4-blade PBT 0.084

350 140

300 120

250 100
Mass of Hub, lbm

Mass of Hub, kg
200 80

Hydrofoil
150 60
4-Blade PBT

100 40

50 20

0 0
0 2 4 6 8 0 5
50 20

0 0
0 2 4 6 8 0 5

Shaft Diameter, in Sh
llers on one

US Units

26.0
2
5.0
1.0

125.0
166.0
12.0
79.0
2.86E+07
0.29
6,000
10,000

0.036
7.50

NA
87.0
166.0
3.75

16.2
12.6

3,782
5,547

1.79
45.37
1.84
46.77
2.0
 20.0

36.24
32.58

41.45
37.27

76.15
78.25

Results

0.5
0.3

140

120

100
Mass of Hub, kg

80

Hydrofoil
60 4-Blade PBT

40

20

0
0 50 100 150 200
20

0
0 50 100 150 200

Shaft Diameter, mm