Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 81 views

    Operating Instructions For The LXP1530 Portable Plasma Cutter

    Uploaded by

    rony linga
    The document provides operating instructions for the LXP1530 Portable Plasma Cutter in 10 steps: 1. Turn on the power switch and gas supply switch. Check that the power and gas pressure indicators are on. 2. Start the water supply equipment and check that the water pressure indicator is on. 3. Adjust the air filter regulator to set the gas pressure and flow for cutting conditions. 4. Check that the power, cutting, gas pressure, water pressure, and overheat indicators are on while other indicators are off. 5. Keep the torch nozzle 2-5mm from the workpiece and cut from the edge while moving the torch.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Operating Instructions For The LXP1530 Portable Plasma Cutter

    Uploaded by

    rony linga
    81 views2 pages
    The document provides operating instructions for the LXP1530 Portable Plasma Cutter in 10 steps: 1. Turn on the power switch and gas supply switch. Check that the power and gas pressure indicators are on. 2. Start the water supply equipment and check that the water pressure indicator is on. 3. Adjust the air filter regulator to set the gas pressure and flow for cutting conditions. 4. Check that the power, cutting, gas pressure, water pressure, and overheat indicators are on while other indicators are off. 5. Keep the torch nozzle 2-5mm from the workpiece and cut from the edge while moving the torch.

    Original Title

    Operating Instructions for the LXP1530 Portable Plasma Cutter

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides operating instructions for the LXP1530 Portable Plasma Cutter in 10 steps: 1. Turn on the power switch and gas supply switch. Check that the power and gas pressure indicators are on. 2. Start the water supply equipment and check that the water pressure indicator is on. 3. Adjust the air filter regulator to set the gas pressure and flow for cutting conditions. 4. Check that the power, cutting, gas pressure, water pressure, and overheat indicators are on while other indicators are off. 5. Keep the torch nozzle 2-5mm from the workpiece and cut from the edge while moving the torch.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    81 views2 pages

    Operating Instructions For The LXP1530 Portable Plasma Cutter

    Uploaded by

    rony linga
    The document provides operating instructions for the LXP1530 Portable Plasma Cutter in 10 steps: 1. Turn on the power switch and gas supply switch. Check that the power and gas pressure indicators are on. 2. Start the water supply equipment and check that the water pressure indicator is on. 3. Adjust the air filter regulator to set the gas pressure and flow for cutting conditions. 4. Check that the power, cutting, gas pressure, water pressure, and overheat indicators are on while other indicators are off. 5. Keep the torch nozzle 2-5mm from the workpiece and cut from the edge while moving the torch.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Operating Instructions for the LXP1530 Portable Plasma Cutter

    ➢ Turn on the power switch. The power indicator lamp is ON;


    ➢ Start gas supply equipment and turn on the gas supply switch, the power
    indicator lamp on the panel is ON. If the gas pressure is less than 0.25Mpa,
    the lamp will be OFF, then the gas source should be checked;
    ➢ Start water supply equipment. The indicator lamp of water pressure on panel
    is ON when opens water supply valve. (LGK-100/120IGBT does not have
    this function)
    ➢ Place the gas control switch to “Check Gas”, adjust the Adjusting knob of air
    filter regulator to make the output pressure and flux fit cutting condition.
    After adjusting, place the knob on “Cutting “position. Select panel operation
    method and control switch point. At 2-Step point, the torch switch; should be
    pressed all the time during cutting. After loosening, the cutting comes to stop.
    At 4-Step point, press the torch switch and then loosen it, and cutting can
    start. User can make selection according to his operation habit;
    ➢ Checking the panel indicator lamps. The indicator lamps status, under which
    cutting can be operated, is shown as following sheet.
    Indicator Power Cutting Gas Water Overheated Supply
    pressure pressure abnormal
    Status ON OFF ON ON OFF OFF

    ➢ Keep the torch nozzle 2mm~ 5mm away from work-piece. The axis line of
    nozzle should be perpendicular to work-piece, and starts cutting from the
    edge of work-piece. When the plate thickness is ≤12mm, a hole can be drilled
    on work-piece and then cutting can be started around the hole. The cutting
    torch should be inclined to one side a little during drilling a hole on work-

    Page |1
    piece, so that the molten metal can be blown away easily. To drill a hole by
    use of plasma arc is not proposed, because this will damage nozzle easily, it
    is better to drill a hole in arc striking point first, then strikes arc on the edge
    of hole. Press down torch switch, compressed gas sprays out from nozzle, and
    cutting indicating lamp is ON. After gas pre-flows for 1 to 2 seconds, high
    frequency is generated, arc is stroke, and cutting begins by moving torch;
    ➢ When the control switch of operation method on front panel is at 2-Step point,
    press down the torch switch and cutting starts after arc striking. After
    loosening the switch, there is no voltage output, and cutting ends, and
    compressed gas stops supply in 9 seconds. When it is at 4-Step point, press
    down the switch and loosen it, and cutting starts after arc striking
    automatically. Press the switch again or press it till the arc is off, then there
    is no voltage output, cutting ends, and compressed gas stops supply in 9
    seconds.

    Page |2

    You might also like