A Perfect Crown Molding

with your Starrett CP505A-12

1) Measure the corner angle near the ceiling. Note
the Miter Cut value from the dial (inner scale).
2) Measure the spring angle of your stock (see below
right) with the protractor on your CP505A-12.
3) Refer to the compound cut conversion table on your tool
(or the back of this page). Locate the row with the same
"Miter Cut" value as your corner measurement.
4) Note the "Miter Angle" and "Bevel Angle" from the row that
corresponds to the 38° or 45° spring angle, as determined in step 2.
5) Refer to the table below and set the miter angle and
bevel angle on your compound miter saw, position
your work piece with reference to the blade and fence,
as indicated. Then, cut your first work piece.
6) Reset the saw and position your second work piece as
indicated below. Then, cut your second work piece.

The two work pieces should align perfectly for your crown molding.
Settings and Layout
to Cut Crown Molding with a Compound Miter Saw
Inside Corner
Left Piece Right Piece
Miter Swing: Right Miter Swing: Left
Bevel Swing: Left Bevel Swing: Left
Work Piece Location: Left of Blade Work Piece Location: Left of Blade
Molding Edge Against Fence: Top Molding Edge Against Fence: Bottom

Outside Corner
Left Piece Right Piece
Miter Swing: Left Miter Swing: Right
Bevel Swing: Right Bevel Swing: Right
Work Piece Location: Right of Blade Work Piece Location: Right of Blade
Molding Edge Against Fence: Bottom Molding Edge Against Fence: Top
 Compound Cut Conversion Table
38° Crown 45° Crown 38° Crown 45° Crown
Miter Miter Bevil Miter Bevil Miter Miter Bevil Miter Bevil
Cut Angle Angle Angle Angle Cut Angle Angle Angle Angle
1 0.6 0.8 0.7 0.7 31 20.3 23.9 23.0 21.4
2 1.2 1.6 1.4 1.4 32 21.0 24.7 23.8 22.0
3 1.9 2.4 2.1 2.1 33 21.8 25.4 24.7 22.7
4 2.5 3.2 2.8 2.8 34 22.6 26.2 25.5 23.3
5 3.1 3.9 3.5 3.5 35 23.3 26.9 26.3 23.9
6 3.7 4.7 4.3 4.2 36 24.1 27.6 27.2 24.6
7 4.3 5.5 5.0 4.9 37 24.9 28.3 28.1 25.2
8 5.0 6.3 5.7 5.7 38 25.7 29.0 28.9 25.8
9 5.6 7.1 6.4 6.4 39 26.5 29.7 29.8 26.4
10 6.2 7.9 7.1 7.1 40 27.3 30.4 30.7 27.0
11 6.8 8.7 7.8 7.8 41 28.2 31.1 31.6 27.6
12 7.5 9.4 8.6 8.5 42 29.0 31.8 32.5 28.2
13 8.1 10.2 9.3 9.2 43 29.9 32.5 33.4 28.8
14 8.7 11.0 10.0 9.9 44 30.7 33.2 34.3 29.4
15 9.4 11.8 10.7 10.6 45 31.8 33.9 35.3 30.0
16 10.0 12.5 11.5 11.2 46 32.5 34.5 36.2 30.6
17 10.7 13.3 12.2 11.9 47 33.4 35.2 37.2 31.1
18 11.3 14.1 12.9 12.6 48 34.4 35.9 38.1 31.7
19 12.0 14.9 13.7 13.3 49 35.3 36.5 39.1 32.3
20 12.6 15.6 14.4 14.0 50 36.3 37.1 40.1 32.8
21 13.3 16.4 15.2 14.7 51 37.2 37.8 41.1 33.3
22 14.0 17.2 15.9 15.4 52 38.2 38.4 42.2 33.9
23 14.7 17.9 16.7 16.0 53 39.3 39.0 43.2 34.4
24 15.3 18.7 17.5 16.7 54 40.3 39.6 44.2 34.9
25 16.0 19.5 18.3 17.4 55 41.3 40.2 45.3 35.4
26 16.7 20.2 19.0 18.1 56 42.4 40.8 46.4 35.9
27 17.4 21.0 19.8 18.7 57 43.5 41.4 47.4 36.4
28 18.1 21.7 20.6 19.4 58 44.6 41.9 48.5 36.8
29 18.8 22.5 21.4 20.1 59 45.7 42.5 49.6 37.3
30 19.6 23.2 22.2 20.7 60 46.8 43.0 50.8 37.8

Form 969 08/11 Specifications subject to change.