En - 10149 2 1996
En - 10149 2 1996
10149-2:1996
Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:32:16 GMT 2006, Uncontrolled Copy, (c) BSI
Incorporating
Amendment No. 1
Specification for
ICS 77.140.50
BS EN 10149-2:1996
Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:32:16 GMT 2006, Uncontrolled Copy, (c) BSI
The following bodies were also represented in the drafting of the standard,
through subcommittees and panels:
Contents
Page
Committees responsible Inside front cover
National foreword ii
Foreword 2
Text of EN 10149-2 3
© BSI 09-1999 i
BS EN 10149-2:1996
Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:32:16 GMT 2006, Uncontrolled Copy, (c) BSI
National foreword
This British Standard has been prepared under the direction of Technical
Committee ISE/10 and is the English language version of EN 10149-2 Hot-rolled
flat products made of high yield strength steels for cold forming — Part 2:1995
Delivery conditions for thermomechanically rolled steels, published by the
European Committee for Standardization (CEN).
This British Standard supersedes BS 1449-1.4:1991 and BS 1449-1.10:1991
which are withdrawn.
Cross references
Publication referred to Corresponding British Standard
EN 10149: BS EN 10149 Specification for hot-rolled flat products
made of high yield strength steels for cold forming
EN 10149-1:1995 Part 1:1996 General delivery conditions
A British Standard does not purport to include all the necessary provisions of a
contract. Users of British Standards are responsible for their correct application.
Compliance with a British Standard does not of itself confer immunity
from legal obligations.
Summary of pages
This document comprises a front cover, an inside front cover, pages i and ii,
the EN title page, pages 2 to 7 and a back cover.
This standard has been updated (see copyright date) and may have had
amendments incorporated. This will be indicated in the amendment table on the
inside front cover.
ii © BSI 09-1999
EUROPEAN STANDARD EN 10149-2
Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:32:16 GMT 2006, Uncontrolled Copy, (c) BSI
NORME EUROPÉENNE
September 1995
EUROPÄISCHE NORM
Descriptors: Iron and steel products, hot rolled products, high yield strength steels, cold-working, metal rolling, designation,
classifications, grades: quality, chemical composition, delivery condition, mechanical properties, inspection, tests, marking
English version
CEN
European Committee for Standardization
Comité Européen de Normalisation
Europäisches Komitee für Normung
Central Secretariat: rue de Stassart 36, B-1050 Brussels
© 1995 All rights of reproduction and communication in any form and by any means reserved in all
countries to CEN and its members
Ref. No. EN 10149-2:1995 E
EN 10149-2:1995
Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:32:16 GMT 2006, Uncontrolled Copy, (c) BSI
Foreword Page
7.2 Delivery condition 4
This European Standard was prepared by the
7.3 Chemical composition 4
Technical Committee ECISS/TC 10, Structural
steels — Qualities, of which the secretariat is held 7.4 Mechanical properties 4
by NNI. 7.5 Technological properties 4
This European Standard shall be given the status of 7.6 Surface finish 4
a national standard, either by publication of an 7.7 Internal soundness 4
identical text or by endorsement, at the latest by
8 Inspection and testing 5
March 1996, and conflicting national standards
shall be withdrawn at the latest by March 1996. 8.1 General 5
According to the CEN/CENELEC Internal 8.2 Sampling 5
Regulations, the following countries are bound to 8.3 Test units 5
implement this European Standard: Austria, 8.4 Verification of chemical composition 5
Belgium, Denmark, Finland, France, Germany,
Greece, Iceland, Ireland, Italy, Luxembourg, 8.5 Preparation of samples and test
Netherlands, Norway, Portugal, Spain, Sweden, pieces 5
Switzerland, United Kingdom. 8.6 Test methods 5
8.7 Retests and resubmission for testing 5
Contents 8.8 Inspection documents 5
Page 9 Marking 5
Foreword 2 10 Disputes 5
1 Scope 3 11 Options 5
2 Normative references 3 Annex A (normative) Location of test
3 Definitions 3 piece 6
4 Information to be supplied by the Annex B (informative) List of
purchaser 4 corresponding former designations 6
4.1 General 4 Annex C (informative) Minimum
4.2 Options 4 inside bend radii for cold forming 7
5 Dimensions, mass and tolerances 4 Figure A.1 — Location of test pieces 6
5.1 Dimensions and tolerances 4 Table 1 — Chemical composition of the ladle
analysis for thermomechanically rolled steels 3
5.2 Mass of steel 4
Table 2 — Mechanical properties for
6 Classification and designation 4 thermomechanically rolled steels 3
6.1 Classification 4 Table B.1 — List of corresponding
6.2 Designation 4 former designations 6
7 Technical requirements 4 Table C.1 — Minimum inside bend radii
7.1 Steel manufacturing process 4 for cold forming 7
2 © BSI 09-1999
EN 10149-2:1995
Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:32:16 GMT 2006, Uncontrolled Copy, (c) BSI
3 Definitions
The definitions given in EN 10149-1 shall apply.
Table 1 — Chemical composition of the ladle analysis for thermomechanically rolled steels
Designation of steel C Mn Si P S Al Nb V Ti Mo B
grade % % % % % total % % % % %
max. max. max. max. max.b % max.a max.a max.a max. max.
Name Material
number min.
S315MC 1.0972 0,12 1,30 0,50 0,025 0,020 0,015 0,09 0,20 0,15 — —
S355MC 1.0976 0,12 1,50 0,50 0,025 0,020 0,015 0,09 0,20 0,15 — —
S420MC 1.0980 0,12 1,60 0,50 0,025 0,015 0,015 0,09 0,20 0,15 — —
S460MC 1.0982 0,12 1,60 0,50 0,025 0,015 0,015 0,09 0,20 0,15 — —
S500MC 1.0984 0,12 1,70 0,50 0,025 0,015 0,015 0,09 0,20 0,15 — —
S550MC 1.0986 0,12 1,80 0,50 0,025 0,015 0,015 0,09 0,20 0,15 — —
S600MC 1.8969 0,12 1,90 0,50 0,025 0,015 0,015 0,09 0,20 0,22 0,50 0,005
S650MC 1.8976 0,12 2,00 0,60 0,025 0,015 0,015 0,09 0,20 0,22 0,50 0,005
S700MC 1.8974 0,12 2,10 0,60 0,025 0,015 0,015 0,09 0,20 0,22 0,50 0,005
a
The sum of Nb, V, and Ti shall be max. 0,22 %.
b If agreed at the time of the enquiry and order the sulfur content shall be max. 0,010 % (ladle analysis).
See clause 11, option 12.
© BSI 09-1999 3
EN 10149-2:1995
Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:32:16 GMT 2006, Uncontrolled Copy, (c) BSI
4 © BSI 09-1999
EN 10149-2:1995
Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:32:16 GMT 2006, Uncontrolled Copy, (c) BSI
© BSI 09-1999 5
EN 10149-2:1995
Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:32:16 GMT 2006, Uncontrolled Copy, (c) BSI
Annex A (normative)
Location of test pieces
This annex gives the location of test pieces.
Dimensions in mm
Type of test Thickness Orientation of the test pieces for Distance of the test piece from the rolled surface
of product widths of
Annex B (informative)
List of corresponding former designations
Table B.1 — List of corresponding former designations
Designation of steel Equivalent former designations ina
gradeb
6 © BSI 09-1999
EN 10149-2:1995
Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:32:16 GMT 2006, Uncontrolled Copy, (c) BSI
Annex C (informative)
Minimum inside bend radii for cold forming
Table C.1 — Minimum inside bend radii for cold forming
Designation of steel grade Minimum recommended inside bend radii for nominal thicknesses (t)
in mma
Name Material number tk3 3<tk6 t>6
© BSI 09-1999 7
BS EN
10149-2:1996
BSI — British Standards Institution
Licensed Copy: London South Bank University, London South Bank University, Fri Mar 24 04:32:16 GMT 2006, Uncontrolled Copy, (c) BSI
Revisions
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
Tel: 020 8996 9000. Fax: 020 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.
Information on standards
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the internationalstandardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
written permission of BSI must be obtained.