Bombas Rexroth A11V (L) O

RE
92500/2023-05-11
Replaces: 2023-01-19
Axial piston variable pump

A11V(L)O series 1x
▶ All-purpose high pressure pump

▶ Size 40 to 260
▶ Nominal pressure 350 bar
▶ Maximum pressure 400 bar
▶ Open circuit
Features Contents
▶ Through-drive for mounting of further pumps up to Type code 2
same size Hydraulic fluid 5
▶ Optional with charge pump for sizes 130 to 260 Working pressure range 7
▶ Higher speeds are possible for the version with Technical data 8
charge pump (A11VLO) Power controller 11
▶ Large variety of controls Pressure controller 22
▶ Swashplate design Hydraulic control, pilot-pressure related 26
▶ Compact design Electrical control with proportional solenoid 28
▶ High efficiency Dimensions, size 40 32
▶ High power density Dimensions, size 60 36
Dimensions, size 75 40
Dimensions, size 130/145 48
Dimensions, through-drive 62
Overview of mounting options 65
Combination pumps A11V(L)O + A11V(L)O 66
Swivel angle indicator 67
Connector for solenoids 69
Installation instructions 70
Project planning notes 74
Safety instructions 75
RE 92500/2023-05-11, Bosch Rexroth AG
2 A11V(L)O series 1x | Axial piston variable pump
Type code
Type code
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15
A11V / N 12 –
Axial piston unit
01 Swashplate design, variable, nominal pressure 350 bar, maximum pressure 400 bar A11V
Operating mode 40 60 75 95 130 145 190 260

02 Pump, open circuit without charge pump ● ● ● ● ● ● ● ● O
with charge pump ‒ ‒ ‒ ‒ ● ● ● ● LO
Size (NG)
03 Geometric displacement, see technical data on page 8 40 60 75 95 130 145 190 260
Control device1) 40 60 75 95 130 145 190 260

04 Power controller fixed setting ● ● ● ● ● ● ● ● LR
with override cross sensing negative control ● ● ● ● ● ● ● ● LR.C
high pressure negative control
● ● ● ● ● ● ● ● LR3
dependent
pilot-pressure related negative control ● ● ● ● ● ● ● ● LG1
positive control ● ● ● ● ● ● ● ● LG2
electric negative control U = 24 V ● ● ● ● ● ● ● ● LE2
with pressure cut-off ● ● ● ● ● ● ● ● L.D..
hydraulic remote controlled ● ● ● ● ● ● ● ● L..G.
with load sensing ● ● ● ● ● ● ● ● L...S
electric proportional override U = 24 V ● ● ● ● ● ● ● ● L...S2
hydraulic proportional override – – – ● ● ● ● ● L...S5
with hydraulic negative control Δp = 25 bar ● ● ● ● ● ● ● ● L...H1
stroke limiter positive control Δp = 25 bar ● ● ● ● ● ● ● ● L...H2
with electric positive control ● ● ● ● ● ● ● ● L...U2
stroke limiter U = 24 V with manual override and
○ ○ ○ ○ ○ ○ ○ ○ L...U6
spring return
Pressure controller ● ● ● ● ● ● ● ● DR
with load sensing ● ● ● ● ● ● ● ● DRS
hydraulic remote controlled ● ● ● ● ● ● ● ● DRG
for parallel operation ● ● ● ● ● ● ● ● DRL
Hydraulic control, positive control Δp = 25 bar ● ● ● ● ● ● ● ● HD2
pilot-pressure related with pressure cut-off Δp = 25 bar ● ● ● ● ● ● ● ● HD2D
Electrical control positive control ● ● ● ● ● ● ● ● EP2
with proportional U = 24 V with manual override and
solenoid ○ ○ ○ ○ ○ ○ ○ ○ EP6
spring return
with pressure cut-off ● ● ● ● ● ● ● ● EP2D
with pressure cut-off,
● ● ● ● ● ● ● ● EP2G
hydraulic remote controlled
with pressure cut-off, negative control – – – ● ● ● ● ● EP2G2
electric remote controlled positive control – – – ● ● ● ● ● EP2G4
● = Available ○ = On request ‒ = Not available
1) The following combinations are not available with the power

controller: LRDS2, LRDS5, L...GS, L...GS2, L...GS5 and the
combination L...DG in conjunction with the stroke limiters H1, H2,
H5, U2, U6.
Bosch Rexroth AG, RE 92500/2023-05-11
Axial piston variable pump | A11V(L)O series 1x 3
Type code
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15
A11V / N 12 –
Series
05 1
Index
06 Size 40 … 130 0
Size 145 … 260 1
Direction of rotation
07 Viewed on drive shaft clockwise R
counter-clockwise L
Sealing material
08 NBR (nitrile rubber), shaft seal ring made of FKM (fluorocarbon rubber) N
FKM (fluorocarbon rubber) V
Drive shaft 40 60 75 95 130 145 190 260

09 Splined shaft DIN 5480 for single and combination pump ● ● ● ● ● ● ● ● Z
Parallel keyed shaft DIN 6885 ● ● ● ● ● ● ● ● P
Splined shaft ANSI B92.1a‒1976 for single pump ● ● ● ● ● ● ● ● S
for combination pump ● ● ● ‒2) ‒2) ‒2) ● ● T
Mounting flange 40 60 75 95 130 145 190 260

10 SAE J744 ‒ 2-hole ● ● ‒ ‒ ‒ ‒ ‒ ‒ C
SAE J744 ‒ 4-hole ‒ ‒ ● ● ● ● ● ● D
SAE J6173) (SAE 3) ‒ ‒ ‒ ● ● ● ● ‒ G
Working port 40 60 75 95 130 145 190 260

11 SAE pressure and suction port at side, opposite,
metric fastening thread according to DIN 13. ● ● ● ● ● ● ● ● 12
Port thread, metric with profile sealing ring based on DIN 3852
SAE pressure and suction port at side, opposite,
metric fastening thread according to DIN 13. ○ ● ● ● ● ● ● ● 07
Port thread, UNF with profile sealing ring based on ISO 11926
2) S-shaft suitable for combination pump!

3) Suitable for flywheel housing of the internal combustion engine
Type code
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15
A11V / N 12 P –
Through-drive
12 Flange SAE J744 4)
Hub for splined shaft4)
Diameter Diameter Designation 40 60 75 95 130 145 190 260
‒ ‒ ● ● ● ● ● ● ● ● N00
82-2 (A) 5/8 in 9T 16/32DP A ● ● ● ● ● ● ● ● K01
3/4 in 11T 16/32DP A-B ● ● ● ● ● ● ● ● K52
101-2 (B) 7/8 in 13T 16/32DP B ● ● ● ● ● ● ● ● K02
1 in 15T 16/32DP B-B ● ● ● ● ● ● ● ● K04
W 35 × 2 × 16 × 9g ● ● ● ● ○ ○ ● ● K79
127-2/-2+4 (C)5) 1 1/4 in 14T 12/24DP C ‒ ● ● ● ● ● ● ● K07
1 1/2 in 17T 12/24DP C-C ‒ ‒ ‒ ● ● ● ● ● K24
W 30 × 2 × 14 × 9g ‒ ● ● ● ●6)
●
6)
● ● K80
W 35 × 2 × 16 × 9g ‒ ● ● ● ● ● ● ● K61
152-4 (D) 1 1/4in 14T 12/24DP C ‒ ‒ ● ● ● ● ● ● K86
1 3/4 in 13T 8/16DP D ‒ ‒ ‒ ‒ ● ● ● ● K17
W 40 × 2 × 18 × 9g ‒ ‒ ● ● ● ● ● ● K81
W 45 × 2 × 21 × 9g ‒ ‒ ‒ ● ● ● ● ● K82
W 50 × 2 × 24 × 9g ‒ ‒ ‒ ‒ ● ● ● ● K83
165-4 (E) 1 3/4 in 13T 8/16DP D ‒ ‒ ‒ ‒ ‒ ‒ ● ● K72
W 50 × 2 × 24 × 9g ‒ ‒ ‒ ‒ ‒ ‒ ● ● K84
W 60 × 2 × 28 × 9g ‒ ‒ ‒ ‒ ‒ ‒ ‒ ● K67
Swivel angle indicator 40 60 75 95 130 145 190 260

13 without swivel angle indicator (without code) ● ● ● ● ● ● ● ●
with optical swivel angle indicator ● ‒ ● ● ● ● ● ● V
with electric swivel angle sensor ● ‒ ● ● ● ● ● ● R
Connector for solenoids 40 60 75 95 130 145 190 260

14 DEUTSCH connector molded 2-pin, without suppressor diode ● ● ● ● ● ● ● ● P
Standard/special version
15 Standard version (without code)
Special version S
Installation variant Y
4) 2 ≙ 2-hole; 4 ≙ 4-hole
5) NG190 and NG260 with 2 + 4 hole flange
6) Not available for version with charge pump
Hydraulic fluid
Hydraulic fluid
The axial piston unit is designed for operation with Selection of hydraulic fluid
HLP mineral oil according to DIN 51524. Bosch Rexroth evaluates hydraulic fluids on the basis of
Application instructions and requirements for hydraulic the Fluid Rating according to the technical
fluid selection, behavior during operation as well as data sheet 90235.
disposal and environmental protection should be taken Hydraulic fluids with positive evaluation in the Fluid Rating
from the following data sheets before the start of project are provided in the following technical data sheet:
planning: ▶ 90245: Bosch Rexroth Fluid Rating List for Rexroth
▶ 90220: Hydraulic fluids based on mineral oils and hydraulic components (pumps and motors)
related hydrocarbons
▶ 90221: Environmentally acceptable hydraulic fluids Selection of hydraulic fluid shall make sure that the
▶ 90223: Fire-resistant, water-containing hydraulic fluids operating viscosity in the operating temperature range is
(HFC/HFB/HFAE/HFAS) within the optimum range (νopt; see selection diagram).
Viscosity and temperature of hydraulic fluids

Viscosity Shaft seal Temperature3) Remarks
Cold start νmax ≤ 1600 mm²/s NBR2) ϑSt ≥ −40 °C t ≤ 3min, without load (p ≤ 50 bar), n ≤ 1000 rpm
FKM ϑSt ≥ −25 °C Permissible temperature difference between axial piston unit
and hydraulic fluid in the system maximum 25 K
Warm-up phase ν = 1600 … 400 mm²/s t ≤ 15 min, p ≤ 0.7 × pnom and n ≤ 0.5 × nnom
Continuous ν = 400 … 10 mm²/s 1)
NBR 2)
ϑ ≤ +85 °C> Measured at port T
operation FKM ϑ ≤ +110 °C>
νopt = 36 … 16 mm²/s Optimal operating viscosity and efficiency range
Short-term νmin = 10 … 7 mm²/s NBR 2)
ϑ ≤ +85 °C> t ≤ 3 min, p ≤ 0.3 × pnom , measured at port T
operation FKM ϑ ≤ +110 °C>
▼ Selection diagram
Maximum permissible viscosity on cold start

1600
Warm-up phase 1000
600
400
200
VG 68
VG 46
VG
VG 32
VG 22
10
Viscosity ν [mm2/s]
100
0
60
Continuous operation 40
36
νopt
20
16
10
Minimum permissible viscosity for short-term operation
7
−40 −25 −10 0 10 30 40 50 70 90 115
Temperature ϑ [°C]
1) This corresponds, for example on the VG 46, to a temperature 2) Special version, please contact us
range of +4 °C to +85 °C (see selection diagram) 3) If the temperature at extreme operating parameters cannot be
adhered to, please contact us.
Hydraulic fluid
Filtration of the hydraulic fluid Charge pump (impeller)

Finer filtration improves the cleanliness level of the The charge pump is a centrifugal pump with which the
hydraulic fluid, which increases the service life of the A11VLO is filled and therefore can be operated at higher
axial piston unit. rotational speeds. This also simplifies cold starting at low
A cleanliness level of at least 20/18/15 is to be maintained temperatures and high viscosity of the hydraulic fluid.
according to ISO 4406. Externally increasing the inlet pressure is therefore
At a hydraulic fluid viscosity of less than 10 mm²/s unnecessary in most cases. Charging the reservoir with
(e.g. due to high temperatures during short-term compressed air is permissible at 2 bar absolute.
operation) at the drain port, a cleanliness level of at least
T1 GM A
19/17/14 according to ISO 4406 is required.
For example, a viscosity of 10 mm²/s corresponds to the
following temperatures with the following media:
Vg max Vg min
▶ HLP 32 a temperature of 73 °C
▶ HLP 46 corresponds to a temperature of 85 °C
Case flushing
If a variable displacement pump with control device EP, R T2 M1 S
HD or with stroke limiter (H1, H2, U2, U6) is operated for
a longer period of time (t > 10 min) with zero flow or
working pressure < 15 bar, housing flushing via the
connections T1, T2 or R is required.
NG 40 60 75 95 130 145 190 260

qV flush (l/min) 2 3 3 4 4 4 5 6
The need for housing flushing is eliminated at the version

with charge pump (A11VLO).
Working pressure range
Working pressure range
Pressure at port for working line A Definition

Nominal pressure pnom 350 bar The nominal pressure corresponds to the maximum design pressure.
Maximum pressure pmax 400 bar The maximum pressure corresponds to the maximum working pressure
Single operating period < 1 s within a single operating period. The sum of single operating periods must
not exceed the total operating period.
Total operating period 300 h
Minimum pressure pA absolute see diagram Minimum pressure at the high-pressure side A which is required in order to
(high-pressure side) "Minimum pressure prevent damage to the axial piston unit.
(high-pressure side)"
Rate of pressure change RA max 16000 bar/s Maximum permissible speed of pressure build-up and reduction during
a pressure change across the entire pressure range.
Pressure at suction port S (inlet)
Version without charge pump
Minimum pressure pS min ≥ 0.8 bar absolute Minimum pressure at suction port S (inlet) which is required to prevent
damage to the axial piston unit. The minimum pressure is dependent
on the rotational speed and displacement of the axial piston unit
(see diagram "Maximum permissible rotational speed" on page 9).
Maximum pressure pS max ≤ 30 bar absolute1)
Version with charge pump
Minimum pressure pS min ≥ 0.6 bar absolute Minimum pressure at suction port S (inlet) which is required to prevent
damage to the axial piston unit.
Maximum pressure pS max ≤ 2 bar absolute
Case pressure at port T1, T2
Maximum case pressure pT max 2 bar Measured at port T1, T2
Maximum 1.2 bar higher than inlet pressure at port S,
but not higher than pT max.
A drain line to the reservoir is required.
▼ Minimum pressure (high-pressure side) ▼ Pressure definition

20
n=
nm t2
18 n= ax Single operating period t1 tn
0.9
×n Maximum pressure pmax
16 n= ma
0.8 x Nominal pressure pnom
×n
14 n =0 ma
Pressure p
.7 x
×n
pA absolute [bar]
ma
12 x
n=0
10 .6 ×
nma
x
8
n = 0.5 × nmax
6 Minimum pressure (high-pressure side)
4 n ≤ 0.4 × nmax
Time t
2 Total operating period = t1 + t2 + ... + tn
0 Notice
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
Displacement Vg/ Vg max ▶ Working pressure range applies when using
hydraulic fluids based on mineral oils.
Please contact us for values for other hydraulic fluids.
▶ The case pressure must be greater than the external
pressure (ambient pressure) at the shaft seal.
1) > 5 bar, please contact us
Technical data
Technical data
Without charge pump (A11VO)

Size NG 40 60 75 95 130 145 190 260
Geometric displacement, Vg max cm3 42.0 58.5 74.0 93.5 130.0 145.0 193.0 260.0
per revolution Vg min cm3 0 0 0 0 0 0 0 0
Maximum at Vg max 1)
nnom rpm 3000 2700 2550 2350 2100 2200 2100 2000
rotational speed at Vg ≤ Vg max3) nmax rpm 3500 3250 3000 2780 2500 2500 21005) 2300
Flow at nnom and Vg max qv l/min 126 158 189 220 273 319 405 468
Power at nnom, Vg max P kW 74 92 110 128 159 186 236 273
and Δp = 350 bar
Torque at Vg max M Nm 234 326 412 521 724 808 1075 1448
and Δp = 350 bar2)
Rotary stiffness Z c kNm/rad 88.9 102.4 145.8 199.6 302.5 302.5 346.2 686.5
drive shaft P c kNm/rad 87.5 107.9 143.1 196.4 312.4 312.4 383.2 653.8
S c kNm/rad 58.3 86.3 101.9 173.7 236.9 236.9 259.8 352.0
T c kNm/rad 74.5 102.4 125.6 148.3 ‒ ‒ 301.9 567.1
Moment of inertia of the rotary group JTW kgm2 0.0048 0.0082 0.0115 0.0173 0.0318 0.0341 0.055 0.0878
Maximum angular acceleration4) α rad/s² 22000 17500 15000 13000 10500 9000 6800 4800
Case volume V L 1.1 1.35 1.85 2.1 2.9 2.9 3.8 4.6
Weight (without through-drive) approx. m kg 32 40 45 53 66 67 95 125
With charge pump (A11VLO)

Size NG 130 145 190 260
Geometric displacement, per revolution Vg max cm 3
130.0 145.0 193.0 260.0
Vg min cm3 0 0 0 0
Maximum at Vg max 2)
nnom rpm 2500 2500 2500 2300
rotational speed at Vg ≤ Vg max nmax rpm 2500 2500 2500 2300
Flow at nnom and Vg max qv l/min 325 363 483 598
Power at nnom, Vg max and P kW 190 211 281 349
Δp = 350 bar
Torque at Vg max and M Nm 724 808 1075 1448
Δp = 350 bar2)
Rotary stiffness Z c kNm/rad 302.5 302.5 346.2 686.5
drive shaft P c kNm/rad 312.4 312.4 383.3 653.8
S c kNm/rad 236.9 236.9 259.8 352.0
T c kNm/rad ‒ ‒ 301.9 567.1
Moment of inertia of the rotary group JTW kgm2 0.0337 0.036 0.0577 0.0895
Maximum angular acceleration 4) α rad/s² 10500 9000 6800 4800
Case volume V L 2.9 2.9 3.8 4.6
Weight (without through-drive) approx. m kg 72 73 104 138
1) The values apply for an absolute pressure (pabsolute) of 1 bar at 4) The scope of application lies between 0 and the maximum
suction port S and for operation with mineral operating fluid. permissible rotational speed. It applies for external stimuli
2) The values apply for an absolute pressure (pabsolute) of at least (e.g. diesel engine 2 to 8 times rotary frequency,
0.8 bar at suction port S and for operation with mineral operating cardan shaft 2 times rotary frequency).
fluid. The limit value is only valid for a single pump.
3) The values apply at Vg ≤ Vg max or when the inlet pressure (pabsolute) The load capacity of the connection parts must be considered.
is increased at the suction port S 5) Higher rotational speed possible with special version after
(see diagram "Maximum permissible rotational speed" page 9) consultation.
Technical data
▼ Maximum permissible rotational speed of the A11VO

Determination of the characteristics
(speed limit)
(pabsolute = inlet pressure) Vg × n × ηv
Flow qv = [l/min]
1000
1.2
p Vg × Δp
ab
=1 Torque M = [Nm]
20 × π × ηhm
s
p .2
1.15 ab
=1 ba
s
.1 r 2 π×M×n qv × Δp
p ba
r
Power P = = [kW]
=1 60000 600 × ηt
Rotational speed n/nnom
ab
s
.0
1.1 ba
p r Key
ab
s =0
.9
ba Vg = Displacement per revolution [cm3]
1.05 r
Δp = Differential pressure [bar]
p n = Rotational speed [rpm]
ab
s =0
1 .8 ηv = Volumetric efficiency
ba
r
ηhm = Hydraulic-mechanical efficiency
0.95 ηt = Total efficiency (ηt = ηv × ηhm)
0.9
0.7 0.8 0.9 1
Displacement Vg/ Vg max
Permissible rotational speed depending on

inlet pressure pabsolute and displacement volume Vg /Vg max.
Observe the max. rotational speed nmax
Permissible radial and axial loading on the drive shafts

Size NG 40 60 75 95 130 145 190 260
Maximum radial force Fq max N 3600 5000 6300 8000 11000 11000 16925 22000
at distance a, b, c a mm 17.5 17.5 20 20 22.5 22.5 26 29
(from shaft collar) Fq
Fq max N 3891 4046 4950 6334 8594 8594 13225 16809
b mm 30 30 35 35 40 40 46 50
a, b, c
Fq max N 2416 3398 4077 5242 7051 7051 10850 13600
c mm 42.5 42.5 50 50 57.5 57.5 66 71
Maximum axial force + Fax max N 1500 2200 2750 3500 4800 4800 6000 4150
Fax –
+
− Fax max N 1500 2200 2750 3500 4800 4800 6000 4150
Notice
▶ Theoretical values, without efficiency and tolerances;
values rounded.
▶ Operation above the maximum values or below the
minimum values may result in a loss of function,
a reduced service life or in the destruction of the axial
piston unit. Bosch Rexroth recommends testing the
loads by means of experiment or calculation /
simulation and comparison with the permissible
values.
▶ Special requirements apply in the case of belt drives.
Please contact us.
Technical data
Permissible input and through-drive torques

Size NG 40 60 75 95 130 145 190 260
Torque at Vg max and Δp = 350 bar1) Mmax Nm 234 326 412 521 724 808 1075 1448
Maximum input torque on drive shaft2)
P ME max Nm 468 648 824 1044 1448 1448 2226 2787
Shaft key DIN 6885 ⌀32 ⌀35 ⌀40 ⌀45 ⌀50 ⌀50 ⌀55 ⌀60
Z ME max Nm 912 912 1460 2190 3140 3140 3140 5780
DIN 5480 W35 W35 W40 W45 W50 W50 W50 W60
S ME max Nm 314 602 602 1640 1640 1640 1640 1640
ANSI B92.1a-1976 (SAE J744) 1 in 1 1/4 in 1 1/4 in 1 3/4 in 1 3/4 in 1 3/4 in 1 3/4 in 1 3/4 in
T ME max Nm 602 970 970 – – – 2670 4070
ANSI B92.1a-1976 (SAE J744) 1 1/4 in 1 3/8 in 1 3/8 in – – – 2 in 2 1/4 in
Through-drive torque, maximum3) MD max Nm 314 521 660 822 1110 1110 1760 2065
▼ Distribution of torques
M1 M2
ME
1st pump 2nd pump M3

MD
Torque at 1st pump M1

Torque at 2nd pump M2
Torque at 3rd pump M3
Input torque ME = M1 + M2 + M3
ME < ME max
Through-drive torque MD = M2 + M3
MD < MD max
1) Efficiency not considered

2) For drive shafts free of radial force
3) Note maximum input torque for shaft S!
Power controller
Power controller
LR – Power controller, fixed setting

The power controller regulates the displacement of the ▼ Circuit diagram NG 40 to 145
pump depending on the working pressure so that a given

drive power is not exceeded at constant drive speed.
The precise control with a hyperbolic characteristic curve,
provides an optimum utilization of available power. T1 M A
The working pressure acts on a rocker via a measuring
spool moved together with the control. An externally
adjustable spring force counteracts this, it determines the Vg max Vg min
power setting. The depressurized basic position is Vg max.
If the working pressure exceeds the set spring force,
the control valve will be actuated by the rocker and the
pump will swivel back from the basic position R T2 M1 S
Vg max toward Vg min. Here, the leverage at the rocker may
be shortened and the working pressure may rise in the
same relation as the displacement is reduced ▼ Circuit diagram NG 190 to 260
(pB × Vg = constant; pB = working pressure;
Vg = displacement).
The hydraulic output power (characteristic curve LR) is M A
T1
influenced by the efficiency of the pump.
Setting range for beginning of control 50 to 350 bar
When ordering, state in plain text:
Vg max Vg min
▶ Drive power P [kW]
▶ Drive speed n [rpm]
▶ Maximum flow qV max [l/min]
Please contact us if you need a performance chart.
R T2 M1 S
▼ Characteristic curve LR
350 bar
Working pressure pB [bar]
beginning of control
Setting range
50 bar
Vg min Displacement Vg max
Power controller
LRC – Override with cross sensing LR3 – High-pressure-dependent override

Cross sensing is total capacity control The high-pressure-dependent power override is a total
(high-pressure-dependent) that connects two equally power control where the working pressure of a mounted
sized A11VO pumps with LRC controllers in power control. fixed pump is applied to the power setting (port Z).
If one pump is operating at pressures below the set Therefore, the A11VO can be set to 100 % of the total
beginning of control, the unused drive power is available to drive power. The power setting of the A11VO is reduced
the other pump, up to 100 % in borderline cases. A total proportionally to the load-dependent increase in the
drive power is thus distributed between two consumers working pressure of the fixed pump. The fixed pump has
according to demand. priority in the total power setting.
Freed-up power due to pressure cut-off or other overrides The measuring surface for the power reduction is adapted
is not taken into account. to the displacement of the fixed pump.
Half-sided cross sensing function ▼ Circuit diagram NG 40 to 145
When using the LRC controller on the 1st pump (A11VO) Z

and a power-controlled pump with through-drive and
without cross-sensing, which is also mounted at the drive,
the required power for the 2nd pump deducted from the T1 M A
settings of the 1st pump. The 2nd pump has priority in the
total power setting.
For design of the controller of the 1st pump, the size and Vg max Vg min
the beginning of control of the power controller of the 2nd
pump are required.
▼ Circuit diagram NG 40 to 145

R T2 M1 S
Z
T1 M A Z
Vg max Vg min LR T1 M A
Vg max Vg min
R T2 M1 S
Z R T2 M1 S
T1 M A
Vg max Vg min LR
R T2 M1 S
Power controller
LG1/2 – Pilot-pressure related override LG2 Positive power override

An external pilot pressure acts on the setting spring of the With positive power override LG2, the force resulting from
power controller via port Z. the pilot pressure supports the setting spring of the power
The mechanically adjusted basic power setting can be controller.
varied by means of different pilot pressure settings. Higher pilot pressure = increased power.
If the pilot pressure signal is adjusted by a load limiting Design recommendation for the control fluid requirement
control, the power reduction of all consumers is reduced at ν = 10 mm²/s is 1.2 l/min for the LG2 function.
to match the available power from the diesel engine.
The pilot pressure for power influencing is generated by an ▼ Circuit diagram NG 40 to 145
external control element which is not part of the A11VO Z

(e.g. BODAS LLC – Application software Load limiting
control (data sheet 95312)).
T1 M A
LG1 Negative power override
With negative power override LG1, the force resulting from
the pilot pressure counteracts the setting spring of the Vg max Vg min
power controller.
Higher pilot pressure = reduced power.
Design recommendation for the control fluid requirement
at ν = 10 mm²/s is 0.9 l/min for the LG1 function. S
R T2 M1

Z
Z
T1 M A
T1 M A
Vg max Vg min
Vg max Vg min
R T2 M1 S
R T2 M1 S
T1 M A
Vg max Vg min
R T2 M1 S
Power controller
LE2 – Electrically proportional override (negative control)

A control current acts against the adjustment spring of the ▼ Circuit diagram NG 40 to 145
power controller via a proportional solenoid.

The mechanically adjusted basic power setting can be
reduced by means of different control current settings. T1 M A
Increasing control current = reduced power.
If the control current signal is variably controlled via
a load limiting control, the power draw of all consumers is Vg max Vg min
adjusted to the power draw possible for the diesel engine
(e.g. BODAS LLC – Application software Load limiting
control (data sheet 95312) in BODAS controller RC2-2).
Direct current of 24 V (LE2) is required to control the
proportional solenoid. R T2 M1 S
Technical data, solenoid LE2

Voltage 24 V (±20 %)
Control current
Start of control 200 mA
End of control 600 mA
Current limit 0.77 A M A
T1
Nominal resistance (at 20 °C) 22.7 Ω
Dither frequency 100 Hz
Duty cycle 100 %
Vg max Vg min
Type of protection: see connector version page 69
▼ Effect of power override with increasing pressure or current
R T2 M1 S
pHD I pSt
LG2
50
LRC LR3 LE2 LG1
Power controller
LRD – With pressure cut-off

The pressure cut-off is a pressure control which adjusts ▼ Circuit diagram NG 40 to 145
the displacement of the pump back to Vg min after reaching

the set pressure command value.
This function overrides the power controller, i.e. the power
control function is executed below the pressure command
value. T1 M A
The valve for pressure cut-off is integrated in the controller
housing and is permanently set to a pressure command
value at the factory. Vg max Vg min
Setting range from 50 to 350 bar.
▼ Characteristic curve
max R T2 M1 S
350
Setting range
50
min
Vg min Displacement Vg max T1 M A
Vg max Vg min
R T2 M1 S
Power controller
LRDS – With pressure cut-off and load sensing ▼ Circuit diagram NG 40 to 145
The load sensing controller works as a load-pressure
X
controlled flow controller and adjusts the displacement of
the pump to the volume required by the consumer.
The flow of the pump is then dependent on the cross
section of the external metering orifice (1), which is (1)
located between the pump and the consumer. Below the
power curve and the setting of the pressure cut-off and
T1 M A
within the control range of the pump, the flow is
independent of the load pressure.
The metering orifice is usually a separately located Vg max Vg min
load sensing directional valve (control block). The position
of the directional valve spool determines the opening
cross-section of the metering orifice and thus the flow of
the pump.
R T2 M1 S
The load sensing controller compares pressure before and
after the metering orifice and keeps the pressure drop
(differential pressure ∆p) across the orifice and therefore ▼ Circuit diagram NG 190 to 260
the flow constant.
If the differential pressure ∆p at the metering orifice X
increases, the pump is swiveled back (towards Vg min),

if the differential pressure ∆p decreases the pump is
swiveled out (towards Vg max), until equilibrium in the (1)
valve is restored.
∆pmetering orifice = ppump – pconsumer T1 M A
The setting range for ∆p is between 14 bar and 25 bar.
The default setting is 18 bar (please specify in plain text).
The stand-by pressure in zero-stroke operation Vg max Vg min
(metering orifice plugged) is slightly above the ∆p setting.
In a standard LS system, the pressure cut-off is integrated
in the pump controller. In an LUDV system, the pressure
cut-off is integrated in the LUDV valve block. R T2 M1 S
The metering orifice 1 (control block) is not included in
the scope of delivery.
at ν = 10 mm²/s is 3.7 l/min for the LS function.
max
350
Setting range
50
min
Power controller
LRS2 – With load sensing, electrically overridable LRS5 – With load sensing, hydraulically overridable
By connecting a control current on a proportional By connecting an external pilot pressure to port Z,
solenoid, the differential pressure ∆p of the load sensing the differential pressure ∆p of the load sensing control can
control can be overridden proportionally. be overridden proportionally.
Increasing current = lower ∆p setting. Increasing pilot pressure = lower ∆p setting.
An example of this is shown in the characteristic curve An example of this is shown in the characteristic curve
below. Please consult us before carrying out project below. Please consult us before carrying out project
planning. planning.
For technical data of solenoid, see page 14 (LE2)
▼ Characteristic curve ▼ Characteristic curve
25 25
18 18
∆pLS [bar]
∆pLS [bar]
14 14
10 10
5 5
200 300 400 500 600 0 5 10 15 20 25 30

Control current I [mA] (at 24 V) Pilot pressure pz [bar]
▼ Circuit diagram NG 40 to 145 ▼ Circuit diagram NG 40 to 145
X Z X
T1 M A T1 M A
Vg max Vg min Vg max Vg min
R T2 M1 S R T2 M1 S
▼ Circuit diagram NG 190 to 260 ▼ Circuit diagram NG 190 to 260
X Z X
T1 M A M A
T1
Vg max Vg min
Vg max Vg min
R T2 M1 S S
R T2 M1
Power controller
LR… – with stroke limiter

Due to the stroke limiter, it is possible to change or limit the
displacement of the pump continuously across the entire
control range. At the LRH, the displacement is adjusted
proportionally to the pilot pressure pSt (max. 40 bar) applied
at port Y or, at LRU, by the control current applied at the
proportional solenoid. Direct current of 24 V (U2, U6) is
required to control the proportional solenoid.
The stroke limiter is overridden by the power controller,
i.e. below the power controller characteristic curve
(hyperbolic characteristic curve) the displacement volume
is adjusted depending on the control current or pilot
pressure. If the set flow or working pressure exceeds the
power control characteristic, the power control overrides
and reduces the displacement along the hyperbolic
characteristic.
With electric stroke limiter LRU2, LRU6 and hydraulic
stroke limiter LRH2, a control pressure of 30 bar is needed
to swivel the pump from its initial position Vg max to Vg min.
The required control power is taken from the working
pressure or the external control pressure applied to
port G.
To ensure that the stroke limiter functions at a low working
pressure of < 30 bar, port G must be supplied with an
external control pressure of about 30 bar.
Notice
▶ If no external control pressure is connected to G,
the shuttle valve must be removed or relieved to the
reservoir.
▶ The proportional solenoids in the U6 version have
manual override and spring return.
Power controller
LRH1 – Hydraulic stroke control (negative control)

With pilot-pressure related control, the pump ▼ Circuit diagram NG 40 to 145
displacement is adjusted proportionally and continuously Y

with a pilot pressure applied at port Y.
Basic position without pilot signal is Vg max.
▶ Control from Vg max to Vg min
With increasing pilot pressure the pump swivels to T1 G M A
a smaller displacement.
▶ Setting range for beginning of control (at Vg max)
4 to 10 bar State the beginning of control in plain text Vg max Vg min
in the order.
▶ Maximum permissible pilot pressure pSt max = 40 bar
The required control fluid is taken from the working
pressure or the external control pressure applied to
port G. R T2 M1 S
In order for the pump to be moved from the basic position

zero or at low working pressure, port G must be supplied ▼ Circuit diagram NG 190 to 260
with external control pressure of at least 30 bar,
Y
maximum 40 bar.
at ν = 10 mm²/s is 1.2 l/min for the H1 function.
Notice
If no external control pressure is connected to G, T1 G M A
this must be indicated in plain text.

In this case, the shuttle valve is not included in the
scope of delivery. Vg max Vg min
Without external control pressure, the stroke control

has only limited functionality. Please contact us.
▼ Characteristic curve H1 R T2 M1 S
35
Pilot pressure pSt [bar]
30
25
20
Setting range
15
10
4
0 0.5 1.0
Pilot pressure increase Vg max to Vg min: ∆p = 25 bar
Power controller
LRH2 – Hydraulic stroke control (positive control)


Start of adjustment without pilot signal is Vg min (at working
pressure or external control pressure >30 bar).
▶ Control from Vg min to Vg max T1 G M A
With increasing pilot pressure the pump swivels to
a higher displacement.
▶ Setting range for beginning of control (at Vg min)
Vg max Vg min
4 to 10 bar State the beginning of control in plain text
in the order.
pressure or the external control pressure applied to port G. R T2 M1 S
zero or at low working pressure, port G must be supplied ▼ Circuit diagram NG 190 to 260
with external control pressure of at least 30 bar, Y
maximum 40 bar.
at ν = 10 mm²/s is 0.3 l/min for the H2 function.
Notice
T1 G M A
Vg max Vg min
scope of delivery.
▶ Without external control pressure, the stroke control
▼ Characteristic curve H2 R T2 M1 S
35
30
25
20
Setting range
15
10
4
0 0.5 1.0
Pilot pressure increase Vg min to Vg max: ∆p = 25 bar
Power controller
LRU2/LRU6 – Electric stroke control (positive control)

With the electrical stroke control with proportional Technical data, solenoid LRU2/LRU6
solenoid, the pump displacement is steplessly adjusted in Voltage 24 V (±20 %)
proportion to the current via the magnetic force. Control current
Beginning of control without pilot signal is Vg min Beginning of control at Vg min 200 mA
(at working or external control pressure > 30 bar). End of control at Vg max 600 mA
The mechanically depressurized basic position is Vg max. Current limit 0.77 A
With increasing control current the pump swivels to Nominal resistance (at 20 °C) 22.7 Ω
a greater displacement (from Vg min to Vg max). Dither frequency 100 Hz
The required control fluid is taken from the working Duty cycle 100 %
pressure or the external control pressure applied to port G. Type of protection: see connector version page 69
zero or at low working pressure, port G must be supplied A wide range of BODAS controllers with application
with external control pressure of at least 30 bar, software and analog amplifiers are available to control the
maximum 40 bar. proportional solenoids.
Notice
▶ If no external control pressure is connected to G, Further information can also be found online under
this must be indicated in plain text. www.boschrexroth.com/mobile-electronics.
scope of delivery.
▼ Characteristic curve T1 G M A
800
Vg max Vg min
600
Control current I [mA]
LRU2
R T2 M1 S
400
200
T1 G M A
0 0.5 1.0
Vg max Vg min
R T2 M1 S
Pressure controller
Pressure controller
DR – Pressure controller
The pressure controller limits the maximum pressure at ▼ Circuit diagram NG 40 to 145
the pump outlet within the control range of the variable

pump. The variable pump only supplies as much
hydraulic fluid as is required by the consumers. T1 M A
If the working pressure exceeds the pressure command
value at the pressure valve, the pump will regulate to
a smaller displacement to reduce the control differential. Vg max Vg min
▶ Basic position in depressurized state: Vg max
▶ Setting range for pressure control: 50 to 350 bar.
Specify pressure controller setting in plain text
when ordering.
R T2 M1 S
max
350
max. 10 [bar]
Setting range
T1 M A
Vg max Vg min
50
min
0
Flow qV [l/min] R T2 M1 S
Pressure controller
DRS – Pressure controller with load sensing

The load sensing controller works as a load-pressure ▼ Circuit diagram NG 40 to 145
controlled flow controller and adjusts the displacement of X

the pump to the volume required by the consumer.
The flow of the pump is then dependent on the cross (1)
section of the external metering orifice (1), which is
located between the pump and the consumer. Below the A
T1 M
setting of the pressure controller and within the control
range of the pump, the flow is not dependent on the
load pressure. Vg max Vg min
The metering orifice is usually a separately located
load sensing directional valve (control block).
The position of the directional valve spool determines the
opening cross-section of the metering orifice and thus the
R T2 M1 S
flow of the pump.
The load sensing controller compares the pressure upstream
the metering orifice to the one downstream the orifice and
keeps the pressure drop (differential pressure ∆p) occurring
here and thus the flow constant. X
If the differential pressure ∆p at the metering orifice rises,
the pump is swiveled back (toward Vg min). If the differential (1)
pressure ∆p drops, the pump is swiveled out (toward Vg max)

until equilibrium at the metering orifice is restored. T1 M A
∆pmetering orifice = ppump – pconsumer
▶ Setting range for ∆p 14 to 25 bar
(please state in plain text) Vg max Vg min
▶ Standard setting 18 bar
The stand-by pressure in zero-stroke operation

(metering orifice closed) is slightly higher than the
R T2 M1 S
∆p setting.
The metering orifice 1 (control block) is not included in
the scope of delivery.
max
350
max. 10 [bar]
Setting range
50
min
0
Flow qV [l/min]
Pressure controller
DRG – Pressure controller, hydraulically remote-controlled

On the remote-controlled pressure controller, the setting ▼ Circuit diagram NG 40 to 145
of the pressure controller can be overridden by a separate 2 1

pressure relief valve (1) to set a lower pressure
max.5m
command value.
X
In addition a separately configured 2/2 directional valve (2)
can be operated to start the pump with low working
pressure (standby pressure).
Setting range for ∆p 14 to 25 bar, standard setting 22 bar
(when ordering, please state in plain text) T1 M A
Both functions can be used individually or in combination
(see circuit diagram).
The external valves are not included in the scope of Vg max Vg min
delivery.
As a separate pressure relief valve (1) we recommend:
DBDH 6 (manual actuation) see data sheet 25402.
R T2 M1 S
max
350 ▼ Circuit diagram NG 190 to 260
2 1
max. 10 [bar]
Setting range
max.5m
X
50
min
0 T1 M A
Flow qV [l/min]
Notice
Vg max Vg min
Remote-controlled pressure cut-off is also possible in
connection with LR, HD and EP.
R T2 M1 S
Pressure controller
DRL – Pressure controller for parallel operation

The DRL pressure controller is suitable for pressure ▼ Circuit diagram NG 40 to 260
control of several A11VO axial piston pumps in parallel

2 1
operation pumping into a common pressure line.
The pressure cut-off has a pressure increase of 3 3
approx. 15 bar from qv max to qv min. The pump regulates
X MD MA
therefore to a pressure dependent swivel angle.
MS
This results in a stable controller behavior.
With the externally installed pressure relief valve (1) the
T1 M A
nominal pressure command value of all pumps connected
to the system is adjusted to the same value.
Vg max Vg min
Each pump can be individually unloaded from the system
by a separately installed 3/2 directional valve (2).
The check valves (3) in the working line (port A) or
control line (connection X) must be generally provided.
The external valves are not included in the scope of R T2 M1 S
delivery.
As a separate pressure relief valve (1) we recommend:
DBDH 6 (manual actuation) see data sheet 25402.
350
335
max. 15 [bar]
Setting range
165
150
65
50
0
Flow qV [l/min]
Hydraulic control, pilot-pressure related
HD2 – Hydraulic control


Start of adjustment without pilot signal is Vg min (at working
pressure or external control pressure >30 bar). T1 G M A
▶ Control from Vg min to Vg max
With increasing pilot pressure the pump swivels to
a higher displacement. Vg max Vg min
▶ Setting range for beginning of control (at Vg min)
4 to 10 bar State the beginning of control in plain text
in the order.
R T2 M1 S
pressure or the external control pressure applied to port G.
zero or at low working pressure, port G must be supplied
with external control pressure of at least 30 bar,
maximum 40 bar.
Notice
scope of delivery.
▶ Without external control pressure, the stroke control by
Vg min has only limited functionality. Please contact us.
▼ HD2 characteristic curve
35
30
25
20
Setting range
15
10
4
0 0.5 1.0
Pilot pressure increase Vg min to Vg max: ∆p = 25 bar
HD2D – Hydraulic control with pressure cut-off

the displacement of the pump back to Vg min after reaching Y

This function overrides the hydraulic stroke control,
i.e. the stroke control function is executed below the
pressure command value. T1 G M A
housing and is permanently set to a pressure command
value at the factory. Vg max Vg min
max
350 R T2 M1 S
max. 10 [bar]

Setting range
50 T1 G M A
min
0
Flow qV [l/min]
Vg max Vg min
R T2 M1 S
Electrical control with proportional solenoid
EP2/EP6 – Electric control

With the electrical control with proportional solenoid, Technical data, proportional solenoid EP2/EP6
the pump displacement is steplessly adjusted in Voltage 24 V (±20 %)
proportion to the current via the magnetic force. Control current
Beginning of control without pilot signal is Vg min Beginning of control at Vg min 200 mA
(at working or external control pressure > 30 bar). End of control at Vg max 600 mA
Control from Vg min to Vg max Current limit 0.77 A
With increasing control current the pump swivels to Nominal resistance (at 20 °C) 22.7 Ω
a higher displacement. Dither frequency 100 Hz
The required control fluid is taken from the working Duty cycle 100 %
pressure or the external control pressure applied to port G. Type of protection: see connector version page 69
zero or at low working pressure, port G must be supplied A wide range of BODAS controllers with application
with external control pressure 1)
of at least 30 bar, software and analog amplifiers are available to control the
maximum 40 bar. proportional solenoids.
Notice
▶ If no external control pressure is connected to G, Further information can also be found online under
this must be indicated in plain text. www.boschrexroth.com/mobile-electronics.
scope of delivery.
has only limited functionality. Please contact us
▶ The proportional solenoids in the EP6 version have T1 G M A
manual override and spring return.
▼ Characteristic curve Vg max Vg min
800
600 R T2 M1 S
Control current I [mA]
EP2
400
200
0 0.5 1.0
1) With an external control pressure supply, it is possible

for the pump to swivel slightly beyond the zero position
(to the mechanical stop).
EP2D/EP6D – Electric control with pressure cut-off

the displacement of the pump back to Vg min after reaching

This function overrides the electric control, i.e. the
control-current-dependent function is executed below T1 G M A
the pressure command value.
housing and is permanently set to a pressure command Vg max Vg min
value at the factory.
R T2 M1 S
max
350

max. 10 [bar]
Setting range
T1 G M A
50
min
0 Vg max Vg min
Flow qV [l/min]
R T2 M1 S
EP2G2 – Electric control with electrically overridable pressure cut-off (negative control)
The remote-controlled G2 pressure controller has A wide range of BODAS controllers with application
a fixed Δp value. An electric pressure relief valve software and analog amplifiers are available to control the
(pilot valve) integrated in the controller enables remote proportional solenoids.
pressure control.
▶ Recommendation for fixed set value at Δp 22 bar. Further information can also be found online under
www.boschrexroth.com/mobile-electronics.
▶ Maximum pressure pmax [bar] (pressure on port A) with ▼ Circuit diagram NG 95 to 260
0 mA current. X
Pilot valve G2
The electro proportional pressure relief valve is directly
controlled with negative control as cartridge version
(see KBPS.8B data sheet 18139-05).
T1 G M A
▼ Characteristic curve G2
450
400 Vg max Vg min
350
Pressure p [bar]
300
250
200 R T2 M1 S
150
100
50
0 25 50 75 100
Control current I [%]
Technical data, proportional solenoid G2

Voltage 24 V
Control current
Minimum pressure pmin 1200 mA
Maximum pressure pmax 0 mA
Maximum rated current 1200 mA
Duty cycle 100 %
EP2G4 – Electric control with electrically overridable pressure cut-off (positive control)
The remote-controlled G4 pressure controller has A wide range of BODAS controllers with application
a fixed Δp value. An electric pressure relief valve software and analog amplifiers are available to control the
(pilot valve) integrated in the controller enables remote proportional solenoids.
pressure control.
▶ Recommendation for fixed set value at Δp 22 bar. Further information can also be found online under
www.boschrexroth.com/mobile-electronics.
▶ Maximum pressure pmax [bar] (pressure on port A) with ▼ Circuit diagram NG 95 to 260
maximum current. X
Pilot valve G4
The electro proportional pressure relief valve is directly
controlled with positive control as cartridge version
(see KBPS.8A data sheet 18139-04).
T1 G M A
▼ Characteristic curve G4
450
400 Vg max Vg min
350
300
Pressure p [bar]
250 R T2 M1 S
200
150
100
50
0 25 50 75 100
Amperage I [%]
Technical data, proportional solenoid G4

Voltage 24 V
Control current
Minimum pressure pmin 0 mA
Maximum pressure pmax 1200 mA
Maximum rated current 1200 mA
Duty cycle 100 %
32 A11V(L)O series 1x | Axial piston variable pump Dimensions [mm]
Dimensions, size 40
Dimensions, size 40
LRDCS – Power controller with pressure cut-off, cross-sensing and load sensing
248
183
123 View Y
Clockwise rotation
1221)
(Counter-clockwise rotation)
74 Z T1 M Z
15
9.7 X
146
T1
100
S
⌀101.6−0.054
A (A)
39
X Y
0
A (S)
201)
103
T2
M1
Flange SAE J744
R
101-2 (B)
W
111 Detail X
12
X T2 S 0
14
28.3
110
45°
21
75
75
6
14
Z M
225 A
7
17
V
Detail W Detail V
183
50.8
77.8
S A
50
19
42.9 23.8
1) Center of gravity
Dimensions [mm] Axial piston variable pump | A11V(L)O series 1x 33
Dimensions, size 40
▼ Splined shaft DIN 5480 ▼ Parallel keyed shaft DIN 6885
Z ‒ W35 × 2 × 16 × 9g P ‒ AS 10 × 8 × 56
40 58
M12 × 1.751)
28 22
9.5 E1×0.2
⌀32
7.5
M101)
DIN509
⌀80.5
⌀40
⌀40
⌀80.5
35
32 66
50
▼ Splined shaft SAE J744 ▼ Splined shaft SAE J744
S ‒ 1 in 15T 16/32 DP 2)
T ‒ 1 1/4 in 14T 12/24 DP2)
7/16–14UNC–2B
38 48
3/8–16UNC–2B
22 28
7.5 9.5
⌀80.5
⌀40
⌀40
⌀80.5
R1.6 R1.6
30 40
46 56
Ports Standard Size pmax [bar]3) State5)

A Working port SAE J518 3/4 in 400 O
Fastening thread DIN 13 M10 × 1.5; 16 deep
S Suction port (without charge pump) SAE J518 2 in 30 O
T1 Drain port DIN 3852 M22 × 1.5; 14 deep 10 4)
R Air bleed port DIN 3852 M22 × 1.5; 14 deep 10 X

M1 Measuring port control pressure DIN 3852 M12 × 1.5; 12 deep 400 X
M Measuring port pressure A DIN 3852 M12 × 1.5; 12 deep 400 X
X Pilot pressure port for version with load sensing (S) and DIN 3852 M14 × 1.5; 12 deep 400 O
remote-controlled pressure cut-off (G)
Y Pilot pressure port for version with stroke limiter (H..) and HD DIN 3852 M14 × 1.5; 12 deep 40 O
Z Pilot pressure port for version with cross sensing (C) and DIN 3852 M14 × 1.5; 12 deep O
power override (LR3) 400
Power override (LG1) 40
G Control pressure port (controller) for version with stroke DIN 3852 M14 × 1.5; 12 deep 40 O
limiter (H.., U2, U6), HP and EP (otherwise plugged)
1) Center bore according to DIN 332 (thread according to DIN 13) 4) Depending on installation position, T1 or T2 must be connected
2) ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance (see also installation instructions on pages 70 to 73)
class 5 5) O = Must be connected (plugged on delivery)
3) Dependent on settings and working pressure X = Plugged (in normal operation)
Dimensions, size 40
▼ LRDH1 – Power controller, pressure cut-off, ▼ LRDH2 – Power controller, pressure cut-off,
hydraulic stroke limiter (negative control) hydraulic stroke limiter (positive control)
248 248
206 206
58 60
18.5 Y G 21.5 Y G
153
153
131
131
106
106
Y Y
21
21
78
78
▼ LRDU2 – Power controller, pressure cut-off, ▼ LR3DS – Power controller, high-pressure-dependent override,
hydraulic stroke limiter (positive control) pressure cut-off, load sensing
290
248
206 228
29 52 Z
G
140
153
106
111 X
78
110
21
▼ HD2D – Hydraulic, pilot-pressure related control, pressure ▼ EP2D – Electric control, proportional solenoid,
cut-off pressure cut-off
208 208
206 206
62 33
23 Y G
G
150.5
106
134
106
Y
78
21
78
Dimensions, size 40
▼ DRS/DRG – Remote-controlled pressure controller, load sensing ▼ DRL – Pressure controller, parallel operation
211.5
209
3
52
135
134
111 X 74 X
110
81
75
▼ LE2S – Power controller, electrical override,
load sensing (negative control)
248
25.5
141.5
111 X
110
Dimensions, size 60
Dimensions, size 60
261.5
198 View Y
Clockwise rotation
140 1)
136
101)
88 Z T1 M Z
41.5
X
12.7
T1
154
108
S
17
⌀127−0.063
46
(A)
0
Y
A
151)
111 A
(S) T2
M1
Flange SAE J744
R
127-2 (C) 181
124.5 213
W
20
X T2 S
112
23
82
82
Z T1 A M
242
V
Detail W
198 Detail V
50.8
77.8
S A
50
19
42.9 23.8
Dimensions, size 60
Z ‒ W35 × 2 × 16 × 9g P ‒ AS 10 × 8 × 56
40 58
M12 × 1.751)
M12 × 1.751)
28 28
9.5 9.5 E1×0.2
⌀35
DIN509
⌀45
⌀45
⌀91
38
⌀91
32 66
50
S ‒ 1 1/4 in 14T 12/24 DP2) T ‒ 1 3/8 in 21T 16/32 DP2)
48 48
7/16–14UNC–2B
7/16–14UNC–2B
28 28
9.5 9.5
⌀45
⌀45
⌀91
⌀91
R1.6 R1.6
40 40
56 56

A Working port SAE J518 3/4 in 400 O

Dimensions, size 60
261.5 261.5
225 225
73.5 73.5
17 Y G 35 Y G
161
161
139
139
110.5
110.5
Y Y
23
23
83
83
261.5 312
225 241
2.5 65.5 Z
G
148
161
110.5
124.5 X
112
23
83
225
225
221.5
75.5 221.5
38 Y G 5.5
G
158.5
139
110.5
110.5
Y
83
23
83
Dimensions, size 60
223.5 225
66.5 10.5
138.5
137
125.5 X 87.5 X
112
76.5
83
261.5
39
150
124.5 X
112
Dimensions, size 75
Dimensions, size 75
276
215
148 View Y
1301) Clockwise rotation
105 Z T1 M
101)
56 Z
12.7 X
T1
160
117
⌀152.4−0.063
101)
A
50
0
Y (S)
A
S
117 (A)
T2
Flange SAE J744

R M1 21
152-4 (D)
138.5 161.6
W
200
19 X T2 S
Z
113.5
24.5
88.5
88.5
260 M
T1 A
Detail W V
215 Detail V
88.9
57.2
S A
63
25
50.8 27.8
Dimensions, size 75
Z ‒ W 40 × 2 × 18 × 9g P ‒ AS 12 × 8 × 80
45 82
36 36
M16 × 21)
M16 × 21) 12 12 E1 × 0.2
⌀40
DIN509
⌀45
⌀45
43
⌀96
⌀96
37 90
55
S ‒ 1 1/4 in 14T 12/24 DP2) T ‒ 1 3/8 in 21T 16/32 DP2)

7/16–14UNC–2B
48 48
7/16-14UNC-2B
28 28
9.5 9.5
⌀45
⌀45
⌀96
⌀96
R1.6 R1.6
40 40
56 56

A Working port SAE J518 1 in 400 O
S Suction port (without charge pump) SAE J518 2 1/2 in 30 O

2) ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, (see also installation instructions on pages 70 to 73)
tolerance class 5 5) O = Must be connected (plugged on delivery)
Dimensions, size 75
276 276
239 239
87.5 87.5
31 Y G 49 Y G
167.5
167.5
145.5
145.5
109
109
Y Y
24.5
24.5
89.5
89.5
326.5
276 255.5
239 80 Z
15 G
154.5
167.5
109
138.5 X
113.5
24.5
89.5
▼ HD2D – Hydraulic, pilot-pressure related control, ▼ EP2D – Electric control, proportional solenoid,
pressure cut-off pressure cut-off
239
235.5 239
89.5 235.5
50.5 Y G 20.5
G
145.5
165
109
109
Y
24.5
89.5
89.5
Dimensions, size 75
238.5 240
80 25.5
142.5
144.5
138.5 X 102.5
X
113.5
89.5
78
276
54
156.5
138.5 X
113.5
Dimensions, size 95
Dimensions, size 95
292
View Y
234
Clockwise rotation
155 (Counter-clockwise rotation)
1421)
113 101)
Z T1 M Z
48
X
12.7
172.5
T1
139
⌀152.4−0.063
101)
0
50
A Y
A S
(S) (A)
125
T2
M
R
161.6
Flange SAE J744 M1
200
152-4 (D)
287
150 Flange SAE3 16
20
W SAE J617 10 15
X T2 S 12
×3
Z 0
115
⌀
26
96
R2
11
77
⌀428.622)
⌀409.582)
⌀101
⌀451
⌀130
⌀385
M
287
T1 A
Detail W V
234 Detail V
R1
106.5
57.2
A
25
S
75
61.9 27.8
2) Dimensions according to SAE J617-No. 3, for connection to the
flywheel housing of the combustion engine
Dimensions, size 95
Z ‒ W 45 × 2 × 21 × 9g P ‒ AS 14 × 9 × 80
50 82
36 36
M16 × 21)
M16 × 21)
12 12 E1×0.2
⌀45
DIN509
48.5
⌀50
⌀50
⌀101
⌀101
42 90
60
▼ Splined shaft SAE J744
S ‒ 1 3/4 in 13T 8/16 DP2)
5/8–11UNC–2B
67
36
12
⌀50
⌀101
R2.5
55
75

Fastening thread DIN 13 M16 × 2; 24 deep
R Air bleed port (flange SAE J744) DIN 3852 M26 × 1.5; 16 deep 10 X
R1 Air bleed port (flange SAE 3) DIN 3852 M26 × 1.5; 16 deep 10 X
Y Pilot pressure port in version with stroke limiter (H...) and DIN 3852 M14 × 1.5; 12 deep 40 O
2-stage pressure cut-off (E) and HD
Load sensing override (S5) 30
G Control pressure port (controller) DIN 3852 M14 × 1.5; 12 deep 40 O
for version with stroke limiter (H.., U2, U6), HP and EP
(otherwise plugged)
Dimensions, size 95
292 292
262 262
97.5 97.5
Y 58.5 Y G
180
180
155
155
115
115
Y Y
97
26
97
26
342.5
292 271.5
262 91 Z
32
166
180
115
150
X
115
97
26
▼ LG1DS – Power controller, pilot-pressure related override, ▼ HD2D – Hydraulic, pilot-pressure related control, pressure
pressure cut-off, load sensing (negative control) cut-off
262
346 252
85 101
62 Y G
157
155
115
z Y
115
26
97
Dimensions, size 95
▼ EP2D – Electric control, proportional solenoid, ▼ EP2G2/EP2G4 – Electric control with electrically overridable
pressure cut-off pressure cut-off (positive/negative control)
310.8
262
261.6
252
31.1 G
31.5
174.9
182
114.7
114.8
123.4
97
255 255
91 36.5
153
157
150 X 113.5 X
115
79.5
97
▼ LE2S – Power controller, electrical override, ▼ LE2S2/LE2S5 – Power controller, electrical override,
load sensing (negative control) load sensing, overridable
293 293
62.5 62.5
169.5
169.5
Partial view LE.S5

233 X 233 X 110
Z
121
121
Dimensions, size 130/145
313 View Y
Clockwise rotation
174
(Counter-clockwise rotation) 29
1701)
101)
134 Z T1 Z X
20
12.7
M
181.5
148
T1
21
⌀152.4−0.063
58
0
Y A S
A
(S) (A)
101)
135
T2
M1
R 161.6
Flange SAE J744
204
152-4 (D)
Flange SAE3 305 (A11VO) / 353 (A11VLO)3)
W SAE J617 16
171 15
10 12
×3
69 X T2 S 0
118
104
R2
⌀
11
⌀409.582)
⌀428.622)
104
⌀451
⌀385
⌀106
⌀130
M
Z 310 T1 A
without charge pump without charge pump with charge pump with charge pump
Detail W Detail V Detail W
R1
Detail V
310 310 344 358
255 255 287 244
106.4
106.4
S A S1
75
75
A1
25
32
66.7
57.2
61.9 27.8 61.9 31.8
1) Center of gravity 3) The housing or length dimension with flange SAE J617-No.3 is
2) Dimensions according to SAE J617-No. 3, for connection to the 5 mm shorter than the standard housing.
Z ‒ W 50 × 2 × 24 × 9g P ‒ AS 14 × 9 × 80
55 82
36
36
M16 × 21)
M16 × 21)
12
12 E1×0.2
⌀50
DIN509
⌀55
⌀106
53.5
⌀55
⌀106
44
65 90
▼ Splined shaft SAE J744
S ‒ 1 3/4 in 13T 8/16 DP2)

5/8–11UNC–2B
67
36
12
⌀55
⌀106
R2.5
55
75
Ports Standard Size pmax State5)

[bar]3)
A1 Working port SAE J518 1 1/4 in 400 O
S1 Suction port (with charge pump) SAE J518 3 in 2 O
R Air bleed port (flange SAE J744) DIN 3852 M26 × 1.5; 16 deep 10 X
X Pilot pressure port for version with load sensing (S) and remote-controlled DIN 3852 M14 × 1.5; 12 deep 400 O
pressure cut-off (G)
Load sensing override (S5) 30
G Control pressure port (controller) for version with stroke limiter DIN 3852 M14 × 1.5; 12 deep 40 O
(H.., U2, U6), HP and EP
319
283 283
116 118.5
Y Y
G G
164
164
115
115
Y Y
29
29
370.2
319
293.2
283
171
Z
175.5
191
135
115
118
29
283
122.5 283
Y
G G
183.5
164
115
115
Y
29
▼ EP2G2/EP2G4 – Electric control with electrically overridable ▼ DRS/DRG – Remote-controlled pressure controller,
pressure cut-off (positive/negative control) load sensing
332.2
283
171 X
G
191
166
135
115
126
X
118
▼ DRL – Pressure controller, parallel operation ▼ LE2S – Power controller, electrical override,
322
254
X
178.5
162
133
X X
124
▼ LE2S2/LE2S5 – Power controller, electrical override,

load sensing, overridable
322
254
X
178.2
133
X
124
Dimensions, size 190
View Y
379 Clockwise rotation
203.5 (Counter-clockwise rotation)
190.5 34
1701) Z T1 M 101) Z
27 X
15.9
196
T1
156
101)
⌀165.1−0.063
66
A S
0
Y
A (S) (A)
T2
163.2
21
M1
R 224.5
Flange SAE J744
165-4 (E) W 262.5
Flange SAE3
318.8 SAE J617 341.8 (A11VO) / 390 (A11VLO)3)
139.8 X 16
T2 Z S 10 15
12
×3
0
131
116
R2
⌀
11
⌀409.582)
⌀428.622)
116
⌀451
⌀126
⌀155
⌀385
M
346.8 T1 A
V
without charge pump without charge pump with charge pump with charge pump
Detail W Detail V Detail W Detail V
346.8 346.8 381.3 R1 395
281.3 281.3 319 272
120.7
120.7
S A S1
90
90
A1
38
38
79.4
79.4
69.9 36.5 69.9 36.5
1) Center of gravity 3) The housing or length dimension with flange SAE J617-No.3 is
2) Dimensions according to SAE J617-No. 3, for connection to the 5 mm shorter than the standard housing.
Z ‒ W 50 × 2 × 24 × 9g P ‒ AS 16 × 10 × 100
55 105
M20 × 2.51)
36 42
M16 × 21)
12 15 E1×0.2
⌀55
DIN509
⌀60
⌀60
⌀126
⌀126
59
44 113
65
S ‒ 1 3/4 in 13T 8/16 DP2) T ‒ 2 in 15T 8/16 DP2)
67 80
5/8–11UNC–2B
5/8–11UNC–2B
36 36
12 12
⌀126
⌀60
⌀126
⌀60
R2.5 R4
55 66
75 88
Ports Standard Size pmax State5)

[bar]3)
A Working port SAE J518 1 1/2 in 400 O
S1 Suction port (with charge pump) SAE J518 3 1/2 in 2 O
T1 Drain port DIN 3852 M33 × 2; 16 deep 10 4)
R Air bleed port (flange SAE J744) DIN 3852 M33 × 2; 16 deep 10 X
R1 Air bleed port (flange SAE 3) DIN 3852 M33 × 2; 16 deep 10 X
R2 Air bleed port (flange SAE 3) DIN 3852 M33 × 2; 16 deep 10 X
X Pilot pressure port for version with load sensing (S) and remote-controlled DIN 3852 M14 × 1.5; 12 deep 400 O
pressure cut-off (G)
power override (LR3) M16 × 1.5; 12 deep 400
Power override (LG1) M14 × 1.5; 12 deep 40
Load sensing override (S5) M14 × 1.5; 12 deep 30
G Control pressure (controller) for version with stroke limiter (H.., U2, U6), DIN 3852 M14 × 1.5; 12 deep 40 O
HP and EP
387.8 387.8
321.5 321.5
145.3 147.8
Y Y
G G
226.5
226.5
176
176
142.5
142.5
Y 34 Y
34
387.8
321.5 387.7
319.3
209.8
X
Z
G
226.5
178
142.5
156
Z X
131
34
▼ LG1GH2 – Power controller, pilot-pressure related override, ▼ LG2H2 – Power controller, pilot-pressure related
stroke control override
432.8 438
356.8 Y2 363
321.5 X Y2
321.5
147.8 147.8
Y1 G Y1
G
234.5
240.5
176
176
142.5
142.5
164
Y1 X Y1
Y2
Y2
34
34
384.8
384.8
321.5
321.5
147.8 Y G
G
187.5
178
183
142.5
142.5
Y
34
▼ EP2G2 – Electric control with electrically overridable ▼ DRS/DRG – Remote-controlled pressure controller,
pressure cut-off (positive control) load sensing
419.3 384.8
321.5 G 319.3
X
187.5
178
156
142.5
131
388.7
321.3 X
178
192.7
156
161.5 X
X
131
89.5

388.8
321.3 X
192.7
156
X
131
408.5 View Y 34
214 Z T1 Clockwise rotation
M 101)
1851) (Counter-clockwise rotation) Z
30 X
15.9
205.5
T1
168
⌀165.1−0.063
101)
72
0
Y A S
A (S) (A)
T2
M1 176.2
21
R R
Flange SAE J744 224.5
165-4 (E)
W 262.5
346
166.5
T2 Z S X
130
137
130
372.1 T1 A
V with charge pump

without charge pump
Detail W Detail V Detail W Detail V
372.1 372.1 414 428

307 307 346 304.1
130.2
120.7
79.4
79.4
100
S A S1 A1
38
38
90
69.9 36.5 77.8 36.5
Z ‒ W 60 × 2 × 28 × 9g P ‒ AS 18 × 11 × 100
58 105
M20 × 2.51)
M20 × 2.51)
42 42
15 15 E1x0.2
⌀60
DIN509
⌀70
⌀70
64
⌀131
⌀131
47 113
66
S ‒ 1 3/4 in 13T 8/16 DP2) T ‒ 2 1/4 in 17T 8/16 DP2)

80
5/8–11UNC–2B
67
3/4–10UNC–2B
36 42
12 15
⌀70
⌀70
⌀131
⌀131
R2.5 R4
55 66
75 88

A Working port SAE J518 1 1/2 in 400 O
S1 Suction port (with charge pump) SAE J518 4 in 2 O
R Air bleed port DIN 3852 M33 × 2; 16 deep 10 X

power override (LR3) M16 × 1.5; 12 deep 400
Power override (LG1) M14 × 1.5; 12 deep 40
Load sensing override (S5) M14 × 1.5; 12 deep 30
G Control pressure (controller) for version with stroke limiter DIN 3852 M14 × 1.5; 12 deep 40 O
(H.., U2, U6), HP and EP
408.5 408.5
351 351
174.5 174.5
116 Y 135.5 Y
G G
239
239
187.5
187.5
152.8
152.8
Y Y
132.5
132.5
40
40
408.5 408.5
351 235
104.5
189.5
239
152.8
345.5 X
132.5
137
Z
40
▼ LG1GH2 – Power controller, pilot-pressure related override ▼ LG2H2 – Power controller, pilot-pressure related override
459.6 464.8
383.6 389.8
351 Y2 351 Y2
174.6 174.6
Y1 G Y1
X G
246
252
187.5
187.5
175.5
152.8
152.8
Y1 X Y1
Y2 Y2
40
40
408.5
351 408.5
174.5 351
135.5 104.5
Y G G
187.5
152.8
194
199
152.8
Y
132.5
132.5
40
▼ EP2G2/EP2G4 – Electric control with electrically overridable ▼ DRS/DRG – Remote-controlled pressure controller,
pressure cut-off (positive/negative control) load sensing
446.1
408.5
351 G
189.5
199
152.8
345.5 X
132.5
137
409.5
342 183
106
203.5
189.5
188 348
X X
132.5
137
95.5

409.5
183
203.5
Partial view LE.S5
348 X 230.3
Z
137
Dimensions, through-drive
Flange SAE J744 Hub for splined shaft1) Availability across sizes Code3)
Diameter Diameter 40 60 75 95 130/145 130/145 2)
190 260
82-2 (A) 5/8 in 9T 16/32 DP1) ● ● ● ● ● ● ● ● K01
3/4 in 11T 16/32 DP 1)
● ● ● ● ● ● ● ● K52
101-2 (B) 7/8 in 13T 16/32 DP1) ● ● ● ● ● ● ● ● K02
1 in 15T 16/32 DP1) ● ● ● ● ● ● ● ● K04
W 35 × 2 × 16 × 9g ● ● ● ● ○ ○ ● ● K79
● = Available ○ = On request
▼ 82-2 (A) ▼ 101-2 (B) size 40 ... 145
A2 A2
A3 O-ring4)
45° O-ring4)
⌀1 A3
⌀101.6
46
⌀82.5
A1
106.4 A1 (to mounting flange)
(to mounting flange)
▼ 101-2 (B) size 190 ... 260
A1 A2 A35)
A-A
NG K01 K52
A3 A
40 240 240 8 M10 × 1.5; 15 deep
O-ring4)
60 257 257 – M10 × 1.5; 15 deep
75 275 275 – M10 × 1.5; 15 deep
95 306 306 – M10 × 1.5; 12.5 deep ⌀1
⌀101.6
46
4 5°
130/145 329 329 – M10 × 1.5; 12.5 deep

130/1452) 363 363 – M10 × 1.5; 12.5 deep
A2
190 359.8 359.8 – M10 × 1.5; 13 deep
1902) 394.3 394.3 – M10 × 1.5; 13 deep A
260 385.1 385.1 – M10 × 1.5; 13 deep
2602) 427.1 427.1 – M10 × 1.5; 13 deep
A1
A1 A2 A35)
NG K02 K04 K79
40 244 244 249 10 M12 × 1.75; 19 deep
60 261 261 265 10 M12 × 1.75; 19 deep
75 279 279 283 10 M12 × 1.75; 19 deep
1) According to ANSI B92.1a, 30° pressure angle, flat root, side fit, 95 303 303 303 10 M12 × 1.75; 16 deep
tolerance class 5 130/145 326 326 326 10 M12 × 1.75; 16 deep
2) Version with charge pump
130/1452) 360 360 – 10 M12 × 1.75; 16 deep
3) The through-drive can be rotated by 90°. Standard position as
190 369.8 369.8 369.8 – M12 × 1.75; 15 deep
shown (version 0°). Please specify in plain text whether version 90°
is used. 1902) 404.3 404.3 404.3 – M12 × 1.75; 15 deep
4) O-ring included in the scope of delivery 260 395.1 395.1 395.1 – M12 × 1.75; 15 deep
5) Thread according to DIN 13. 2602) 437.1 437.1 437.1 – M12 × 1.75; 15 deep
Flange SAE J744 Hub for splined shaft1) Availability across sizes Code3)
Diameter Diameter 40 60 75 95 130/145 130/1452) 190 260
127-2 (C) 1 1/4 in 14T 12/24 DP 1) – ● ● ● ● ● – – K07
1 1/2 in 17T 12/24 DP1) – – – ● ● ● – – K24
W 30 × 2 × 14 × 9g – ● ● ● ● – – – K80
W 35 × 2 × 16 × 9g – ● ● ● ● ● – – K61
127-2+4 (C) 1 1/4 in 14T 12/24 DP1) – – – – – – ● ● K07
1 1/2 in 17T 12/24 DP1) – – – – – – ● ● K24
W 30 × 2 × 14 × 9g – – – – – – ● ● K80
W 35 × 2 × 16 × 9g – – – – – – ● ● K61
▼ 127-2 (C) ▼ 127-2+4 (C)
A2
A2
O-ring4) O-ring4)
A3
A35)
⌀127
⌀127
115
181 115 A1
181 (to mounting flange)
213 A1
A1 A2 A35) A1 A2 A35)
NG K07 K24 K80 K61 NG K07 K24 K80 K61
60 272 – 265 265 13 M16 × 2; 20 deep 190 365.8 367.8 367.8 367.8 13 M16 × 2; 19 deep
75 290 – 290 290 13 M16 × 2; 20 deep 190 2)
400.3 402.3 400 400 13 M16 × 2; 19 deep
95 318 318 318 318 13 M16 × 2; 16 deep 260 391.1 391.1 391.1 391.1 13 M16 × 2; 19 deep
130/145 330 341 330 330 13 M16 × 2; 20 deep 2602) 433.1 433.1 433.1 433.1 13 M16 × 2; 19 deep
130/1452) 364 375 364 364 13 M16 × 2; 20 deep
1) According to ANSI B92.1a, 30° pressure angle, flat root, side fit, 4) O-ring included in the scope of delivery
tolerance class 5 5) Thread according to DIN 13.
3) The through-drive can be rotated by 90°. Standard position as
shown (version 0°). Please specify in plain text whether version 90°
is used.
Flange SAE Hub for splined shaft1) Availability across sizes Code3)
J744
Diameter Diameter 40 60 75 95 130/145 130/1452) 190 260
152-4 (D) 1 1/4in 14T 12/24DP – – ● ● ● ● ● ● K86
1 3/4 in 13T 8/16 DP1) – – – – ● ● ● ● K17
W 40 × 2 × 18 × 9g – – ● ● ● ● ● ● K81
W 45 × 2 × 21 × 9g – – – ● ● ● ● ● K82
W 50 × 2 × 24 × 9g – – – – ● ● ● ● K83
165-4 (E) 1 3/4 in 13T 16/32 DP1) – – – – – – ● ● K72
W 50 × 2 × 24 × 9g – – – – – – ● ● K84
W 60 × 2 × 28 × 9g – – – – – – – ● K67
▼ 152-4 (D) ▼ 165-4 (E)
A2
A2
A3
A3 O-ring4)
O-ring4)
⌀152.4
⌀165.1
161.6
224.5
0
⌀27
161.6 A1
(to mounting flange) 224.5 A1
A1 A2 A35) A1 A2 A35)
NG K86 K17 K81 K82 K83 NG K72 K84 K67
75 290 – 290 – – 13 M20 × 2.5; 28 deep 190 389.8 374.8 – 19 M20 × 2.5; 26 deep
95 317 327 317 317 – 30 M20 × 2.5; 25 deep 1902) 424.3 409.3 – 19 M20 × 2.5; 20 deep
130/ 260 415.1 400.1 400.1 19 M20 × 2.5; 20 deep
340 350 340 340 340 13 M20 × 2.5; 25 deep
145
2602) 457.1 442.1 442.1 19 M20 × 2.5; 20 deep
130/
374 383 374 374 374 13 M20 × 2.5; 25 deep
1452)
190 392 391.8 391.8 392 391.8 13 M20 × 2.5; 22 deep
1902) 424 426.3 426.3 424 426.3 13 M20 × 2.5; 22 deep
260 417 417.1 417.1 417 417.1 13 M20 × 2.5; 22 deep
260 2)
459 459.1 459.1 459 459.1 13 M20 × 2.5; 22 deep
1) According to ANSI B92.1a, 30° pressure angle, flat root, side fit, 4) O-ring included in the scope of delivery
tolerance class 5 5) Thread according to DIN 13.
3) Mounting holes pattern viewed on through-drive with control at top
Overview of mounting options
Overview of mounting options
Through-drive Mounting option – 2nd pump

Flange Hub for Code A11VO/10 A10V(S)O/31 A10V(S)O/53 A4VG/32
splined shaft NG (shaft) NG (shaft) NG (shaft) NG (shaft)
82-2 (A) 5/8 in K01 – 18 (U) 10 (U) –
3/4 in K52 – 18 (S) 10 (S) –
101-2 (B) 7/8 in K02 – 28 (S), 45 (U) 28 (S), 45 (U) –
1 in K04 40 (S) 45 (S) 45 (S), 60 (U) 28 (S)
W35 K79 40 (Z) – – –
127-2/-4 (C) 1 1/4 in K07 60 (S) 71 (S), 100 (U) 60 (S)1), 85 (U) 40, 56, 71 (S)
1 1/2 in K24 – 100 (S) 85 (S) –
W30 K80 – – – 40, 56 (KXX)
W35 K61 60 (Z) – – 40, 56 (A), 71 (Z)
152-4 (D) 1 1/4 in K86 75 (S) – – –
1 3/4 in K17 95, 130, 145 (S) – – 90, 125 (S)
W40 K81 75 (Z) – – 125 (Z)
W45 K82 95 (Z) – – –
W50 K83 130, 145 (Z) – – –
165-4 (E) 1 3/4 in K72 190, 260 (S) – – –
W50 K84 190 (Z) – – –
W60 K67 260 (Z) – – –
Through-drive Mounting option – 2nd pump

Flange Hub for Code A4VG/40 A10VG External gear pump2)
splined shaft NG (shaft) NG (shaft)
82-2 (A) 5/8 in K01 – – AZPF, AZPS NG4 … 28, AZPW NG5 … 22
3/4 in K52 – – AZPF NG4 … 28
101-2 (B) 7/8 in K02 – 18 (S) AZPN-11 NG20 … 25, AZPG-22 NG28 … 100
1 in K04 – 28, 45 (S) –
W35 K79 – – –
127-2/-4 (C) 1 1/4 in K07 – 63 (S) –
1 1/2 in K24 – – –
W30 K80 – – –
W35 K61 – – –
152-4 (D) 1 1/4 in K86 – – –
1 3/4 in K17 110, 125, 145, 175 (T1) – –
W40 K81 – – –
W45 K82 – – –
W50 K83 – – –
165-4 (E) 1 3/4 in K72 175 (T1) – –
W50 K84 – – –
W60 K67 – – –
1) A10VO with 4-hole flange can only be mounted on A11V(L)O

190 and 260.
2) Bosch Rexroth recommends special versions of the external gear
pumps. Please contact us.
Combination pumps A11V(L)O + A11V(L)O
Total length A1)

A11VO (1st pump) A11VO (2nd pump) A11VLO (2nd pump)
NG40 NG60 NG75 NG95 NG130/145 NG190 NG260 NG130/145 NG190 NG260
NG40 – – – – – – – – – –
NG60 490 507 – – – – – – – –
NG75 – 525 550 – – – – – – –
NG95 528 560 577 604 – – – – – –
NG130/145 551 572 600 627 650 – – 698 – –
NG190 586.8 609.8 652 679 702 723.6 750 772.3 –
NG260 620 633.5 677 704 727 746.8 772 775 795.5 828
A11VLO (1st pump) A11VO (2nd pump) A11VLO (2nd pump)

NG40 NG60 NG75 NG95 NG130/145 NG190 NG260 NG130/145 NG190 NG260
NG130/145 585 606 634 661 684 – – 732 – –
NG190 619 642 684 711 734 755.8 – 782 804.5 –
NG260 662.5 675.5 719 746 769 789.3 814.5 817 838 870.5
By using combination pumps, it is possible to have ▼ Total length of a combination pump

independent circuits without the need for splitter gearboxes.
When ordering combination pumps the type designations Hub
for the 1st and the 2nd pump must be joined by a "+". Flange
Order example:
A11VO130LRDS/10R-NZD12K61+ A11VO60LRDS/10-
NZC12N00 A11VO A11VO (2nd
A tandem pump, with two pumps of equal size, (1st pump) pump)
is permissible without additional supports,
assuming that the dynamic mass acceleration does not
A
exceed maximum 10 g (= 98.1 m/s2).
For combination pumps consisting of more than
two pumps, the mounting flange must be calculated for
the permissible mass torque.
Notice
▶ The combination pump type code is shown in short-
ened form in the order confirmation.
▶ The permissible through-drive torques are to be
observed (see page 10).
1) When using the Z-shaft (splined shaft DIN 5480) for the mounted
pump (2nd pump)
Swivel angle indicator
Swivel angle indicator
Optical swivel angle indicator V

With the optical swivel angle indicator, the swivel position
of the pump is indicated by a mechanical indicator on the
side of the housing.
▼ Circuit diagram
T1 GM A
Vg max Vg min
Vg min
R T2 Vg max M1 S
▼ Swivel angle indicator
0
1
A
C
NG A C
40 50.5 84.0
60 not available
75 60.7 97.0
95 63.5 104.0
130 70.9 112.0
190 87.6 123.5
260 87.6 137.0
Electric swivel angle sensor R AMP Superseal mating connector

With electric swivel angle indicator, the pump swivel Consisting of AMP designation
position is measured by an electric swivel angle sensor. 1 housing 3-pin 282087-1
It has a robust, sealed housing and an integrated 3 seals yellow 281934-2
electronics unit that has been developed for automotive 3 sockets 1.8 - 3.3 mm 283025-1
applications.
The mating connector is not included in the scope of
As an output the Hall effect swivel angle sensor delivers
delivery.
a voltage signal proportional to the swivel angle.
This can be supplied by Bosch Rexroth on request
▼ Circuit diagram (material number R902602132).
T1 GM A
▼ Electric swivel angle sensor
Vg max Vg min
R T2 M1 S Detail V not to scale

U
Characteristics A
B Ground GND Ub
Supply voltage Ub 10 ... 30 V DC
2.5 V 4.5 V Output voltage Ua
Output voltage Ua
(Vg min) (Vg max)
C
Reverse polarity protection Short circuit resistant

EMC resistance Details on request V
Operating temperature range –40 ... +125 °C
Vibration resistance
10 g / 5 ... 2000 Hz
sinusoidal vibration EN 60068-2-6 NG A B C
Shock resistance: 40 50.5 88.5 118.3

25 g
continuous shock IEC 68-2-29 60 not available
Salt spray resistance 75 60.7 98.7 131.3
96 h
DIN50021-SS 95 63.5 101.5 138.3
Type of protection DIN/EN 60529 IP67 and IP69K 130 70.9 108.9 146.3
Housing material Plastic 190 87.6 125.6 157.8
260 87.6 125.6 171.3
Connector for solenoids
Connector for solenoids
DEUTSCH DT04-2P-EP04
Molded, 2-pin, without bidirectional suppressor diode
The following type of protection ensues with the installed
mating connector:
▶ IP67 (DIN/EN 60529) and
▶ IP69K (DIN 40050-9)
▼ Switching symbol
Mating connector DEUTSCH DT06-2S-EP04
Consisting of DT designation
1 housing DT06-2S-EP04
1 wedge W2S
2 sockets 0462-201-16141
The mating connector is not included in the scope of

delivery.
This can be supplied by Bosch Rexroth on request
(material number R902601804).
Notice
▶ If necessary, you can change the position of the
connector by turning the solenoid body.
▶ The procedure is defined in the instruction manual.
Installation instructions
General Key
The axial piston unit must be filled with hydraulic fluid and F1/F2 Filling / Air bleeding
vented during commissioning and operation. This must also S Suction port
be observed during longer standstills, as the T1/T2 Drain port
axial piston unit can empty itself via the hydraulic lines. SB Baffle (baffle plate)
Particularly in the installation position "drive shaft upwards", ht min Minimum required immersion depth (200 mm)
filling and air bleeding must be carried out completely as hmin Minimum required distance to reservoir bottom (100 mm)
there is, for example, a danger of dry running. hES min Minimum height required to prevent axial piston unit from
The leakage in the housing area must be directed to the draining (25 mm)
reservoir via the highest drain port (T1/T2). hS max Maximum permissible suction height (800 mm)
For combination pumps, the leakage must be drained off
Notice
at each single pump.
If a shared drain line is used for several units, make sure ▶ In certain installation positions, an influence
that the respective case pressure in each unit is not on the control or control can be expected.
exceeded. The shared drain line must be dimensioned to Gravity, dead weight and case pressure can cause
ensure that the maximum permissible case pressure of all minor characteristic shifts and changes in
connected units is not exceeded in any operating actuating time.
condition, particularly at cold start. If this is not possible, ▶ Ports F1 and F2 are part of the external piping and
separate drain line must be laid, if necessary. must be provided on the customer side to make filling
To prevent the transmission of structure-borne noise, and air bleeding easier.
use elastic elements to decouple all connecting lines
from all vibration-capable components
(e.g. reservoir, frame parts).
Under all operating conditions, the suction line and
drain line must flow into the reservoir below the minimum
fluid level of the reservoir. The permissible suction height
hS results from the total pressure loss, but must not be
higher than hS max = 800 mm. The minimum suction pressure
at port S of 0.8 bar absolute (without charge pump) or
0.6 bar absolute (with charge pump) must not be fallen
below during operation (cold start 0.5 bar absolute).
For the reservoir design, ensure that there is an adequate
distance between the suction line and the drain line.
We recommend using a baffle (baffle plate) between
suction line and drain line. A baffle improves the air
separation ability as it gives the hydraulic fluid more time
for desorption. Apart from that, this prevents the heated
return flow from being drawn directly back into the
suction line. The suction port must be supplied with
air-free, calmed and cooled hydraulic fluid.
Installation position
See the following examples 1 to 10.
Further installation positions are available upon request.
Recommended installation position: 1 and 2
Below-reservoir installation (standard) ▼ Installation position 4

Below-reservoir installation means that the axial piston unit
Air bleeding the housing Filling
is installed outside of the reservoir below the minimum
R F1 (T1/T2), S
fluid level.
SB F1
▼ Installation position 1 ht min
Air bleeding the housing Filling hmin

F1 (T1) F1 (T1), S
F1 SB
ht min R T1
hmin T2
S
T1 S
▼ Installation position 2

F1 (T2) F1 (T2), S
SB F1
ht min
hmin
T2 R
S T1

F1 (T1/T2) F1 (T1/T2), S
F1 SB
ht min
hmin
S
T2
T1 R
For key, see page 70.
Above-reservoir installation ▼ Installation position 7

Above-reservoir installation means that the axial piston unit
is installed above the minimum fluid level of the reservoir.
R, F2 (S) F1 (T1 /T2), F2 (S)
To prevent the axial piston unit from draining, a height
F1
difference hES min of at least 25 mm at port R is required in
hES min
position 7. R
The version A11VLO (with charge pump) is not intended for F2 T1
0.5 bar
above-reservoir installation.
T2
Recommendation for installation position 7 (shaft upward): S
A check valve in the drain line (cracking pressure 0.5 bar)
SB hS max
can prevent draining of the housing area. For control
options with pressure controllers, stroke limiters, ht min
HD and EP control, the minimum displacement setting must hmin

be Vg ≥ 5 % Vg max.
Observe the maximum permissible suction height
hS max = 800 mm.

F1 (T1), F2 (S) F1 (T1), F2 (S)
F1
F2
T1 S
R T2
hS max SB
ht min
hmin

R, F2 (S) F1 (T2), F2 (S)
F1
F2 T2 R
S T1
SB hS max
ht min
hmin
Inside-reservoir installation ▼ Installation position 10

Inside-reservoir installation is when the axial piston unit is
installed in the reservoir below the minimum fluid level.
R The housing of the
The axial piston unit is completely below the hydraulic fluid. axial piston unit is to be filled
If the minimum fluid level is equal to or below the upper using T2 before attachment
edge of the pump, see chapter "Above-reservoir installation". of the piping
Axial piston units with electric components
(e.g. electric controls, sensors) may not be installed in R
SB T2
a reservoir below the fluid level.
S
If inside-reservoir installation is intended nevertheless, the ht min
IP protection class and the medium compatibility of the
electric components used must be checked in the
individual case. Please consult your proper contact person hmin T1
at Bosch Rexroth to commission an examination of the
medium compatibility.
Notice
▼ Installation position 8 ▶ Installation of the pump with EP control in the oil
Air bleeding the housing Filling reservoir only when using mineral hydraulic oils and
T1 The housing of the axial piston an oil temperature in the reservoir of max. 80 °C.
unit is to be filled via T1 before ▶ In this case, the other drain port must be plugged.
attachment of the piping The housing of the axial piston unit must be filled
before fitting the piping and filling the reservoir with
T1 hydraulic fluid.
SB
ht min
S
R hmin

R The housing of the
axial piston unit is to be filled
via T1/T2 before attachment of
the piping
SB
ht min
T2
S T1
hmin
Project planning notes
Project planning notes
▶ The pump is designed to be used in open circuits. ▶ For controllers requiring external pilot pressure, suffi-
▶ Project planning, installation and commissioning of the cient control fluid must be provided to the associated
axial piston units requires the involvement of skilled ports to ensure the required pilot pressures for the
personnel. respective controller function. These controllers are
▶ Before using the axial piston unit, please read the subject to leakage due to their design. An increase in
corresponding instruction manual completely and control fluid demand has to be anticipated over the
thoroughly. If necessary, this can be requested from total operating time. The design of the control fluid
Bosch Rexroth. supply must thus be sufficiently large. If the control
▶ Before finalizing your design, please request a binding fluid is too low, the respective controller function may
installation drawing. be impaired and undesired system behavior may result.
▶ The specified data and notes contained herein must be ▶ Please note that a hydraulic system is an oscillating
observed. system. This can lead, for example, to the stimulation
▶ Depending on the operating conditions of the the natural frequency within the hydraulic system
axial piston unit (working pressure, fluid temperature), during operation at constant rotational speed over
the characteristic curve may shift. a long period of time. The excitation frequency of the
▶ Preservation: Our axial piston units are supplied as pump is 9 times the rotational speed frequency.
standard with preservation protection for a maximum This can be prevented, for example, with suitably
of 12 months. If longer preservation protection is designed hydraulic lines.
required (maximum 24 months), please specify this in ▶ Please note the details regarding the tightening torques
plain text when placing your order. The preservation of port threads and other threaded joints in the
periods apply under optimal storage conditions, instruction manual.
details of which can be found in the data sheet 90312 ▶ The ports and fastening threads are designed for the
or the instruction manual. pmax permissible pressures of the respective ports,
▶ Not all versions of the product are approved for use in see the connection tables. The machine or system
a safety function according to ISO 13849. Please consult manufacturer must ensure that the connecting elements
the responsible contact person at Bosch Rexroth and lines correspond to the specified application
if you require reliability parameters (e.g. MTTFD) for conditions (pressure, flow, hydraulic fluid,
functional safety. temperature) with the necessary safety factors.
Depending on the type of control used, electromagnetic ▶ The working ports and function ports are only intended
effects can be produced when using solenoids. to accommodate hydraulic lines.
Applying a direct voltage signal (DC) to solenoids does
not create electromagnetic interference (EMI) nor is the
solenoid affected by EMI. Electromagnetic interference
(EMI) potential exists when operating and controlling
a solenoid with a modulated direct voltage signal
(e.g. PWM signal) Appropriate testing and measures
should be taken by the machine manufacturer to ensure
other components or operators (e.g. with pacemaker)
are not affected by this potential.
▶ Pressure controllers are not safeguards against
pressure overload. Be sure to add a pressure relief
valve to the hydraulic system.
Safety instructions
Safety instructions
▶ During and shortly after operation, there is a risk of

burning on the axial piston unit and especially on the
solenoids. Take the appropriate safety measures
(e.g. by wearing protective clothing).
▶ Moving parts in control equipment (e.g. valve spools)
can, under certain circumstances, get stuck in position
as a result of contamination (e.g. contaminated
hydraulic fluid, abrasion, or residual dirt from
components). As a result, the hydraulic fluid flow and
the build-up of torque in the axial piston unit can no
longer respond correctly to the operator’s
specifications. Even the use of various filter elements
(external or internal flow filtration) will not rule out
a fault but merely reduce the risk.
The machine/system manufacturer must test whether
remedial measures are needed on the machine for the
application concerned in order to bring the driven
consumer into a safe position (e.g. safe stop) and
ensure any measures are properly implemented.
Bosch Rexroth AG © Bosch Rexroth AG 1992. All rights reserved, also regarding any disposal,

Glockeraustraße 2 exploitation, reproduction, editing, distribution, as well as in the event of
89275 Elchingen applications for industrial property rights. The data specified within only
Germany serves to describe the product. No statements concerning a certain condition
Phone +49 7308 82-0 or suitability for a certain application can be derived from our information.
info.ma@boschrexroth.de The information given does not release the user from the obligation of own
www.boschrexroth.com judgment and verification. It must be remembered that our products are
subject to a natural process of wear and aging.

Bombas Rexroth A11V (L) O

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bombas Rexroth A11V (L) O

Uploaded by

Copyright:

Available Formats

RE

Axial piston variable pump

▶ All-purpose high pressure pump

Operating mode 40 60 75 95 130 145 190 260

Control device1) 40 60 75 95 130 145 190 260

● = Available ○ = On request ‒ = Not available

1) The following combinations are not available with the power

Drive shaft 40 60 75 95 130 145 190 260

Mounting flange 40 60 75 95 130 145 190 260

Working port 40 60 75 95 130 145 190 260

● = Available ○ = On request ‒ = Not available

2) S-shaft suitable for combination pump!

Swivel angle indicator 40 60 75 95 130 145 190 260

Connector for solenoids 40 60 75 95 130 145 190 260

● = Available ○ = On request ‒ = Not available

Viscosity and temperature of hydraulic fluids

Maximum permissible viscosity on cold start

Filtration of the hydraulic fluid Charge pump (impeller)

NG 40 60 75 95 130 145 190 260

The need for housing flushing is eliminated at the version

Working pressure range

Pressure at port for working line A Definition

▼ Minimum pressure (high-pressure side) ▼ Pressure definition

1) > 5 bar, please contact us

Without charge pump (A11VO)

With charge pump (A11VLO)

▼ Maximum permissible rotational speed of the A11VO

0.95 ηt = Total efficiency (ηt = ηv × ηhm)

Permissible rotational speed depending on

Permissible radial and axial loading on the drive shafts

Permissible input and through-drive torques

1st pump 2nd pump M3

Torque at 1st pump M1

1) Efficiency not considered

LR – Power controller, fixed setting

pump depending on the working pressure so that a given

Vg min Displacement Vg max

LRC – Override with cross sensing LR3 – High-pressure-dependent override

Half-sided cross sensing function ▼ Circuit diagram NG 40 to 145

When using the LRC controller on the 1st pump (A11VO) Z

▼ Circuit diagram NG 40 to 145

▼ Circuit diagram NG 190 to 260

▼ Circuit diagram NG 190 to 260

LG1/2 – Pilot-pressure related override LG2 Positive power override

external control element which is not part of the A11VO Z

▼ Circuit diagram NG 40 to 145

LE2 – Electrically proportional override (negative control)

power controller via a proportional solenoid.

Technical data, solenoid LE2

▼ Effect of power override with increasing pressure or current

LRD – With pressure cut-off

the displacement of the pump back to Vg min after reaching

Setting range from 50 to 350 bar.

▼ Circuit diagram NG 190 to 260

Vg min Displacement Vg max T1 M A

increases, the pump is swiveled back (towards Vg min),

Vg min Displacement Vg max

▼ Characteristic curve ▼ Characteristic curve

200 300 400 500 600 0 5 10 15 20 25 30

▼ Circuit diagram NG 40 to 145 ▼ Circuit diagram NG 40 to 145

Vg max Vg min Vg max Vg min

▼ Circuit diagram NG 190 to 260 ▼ Circuit diagram NG 190 to 260

LR… – with stroke limiter